LCD DISPLAY quick start guide 400CX-2, 400CXN-2, 460CX-2, 460CXN-2 ii
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing,contact your dealer. Contact a local dealerto buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box Check the contents of by holding the grooves the package. on both sides of the package box. Remove the Styrofoam and vinyl cover.
Introduction Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all locations) MagicInfo Software CD, MagicInfo Manual CD (Applicable to the CXN-2 model only) Cables Power Cord Others Remote Control Batteries (AAA X 2) (Not available in all locations) Sold separately DVI Cable LAN Cable (Applicable to the CXN-2 model only) 10 Wall Mount KIT
Introduction Sold separately Component to D-sub Cable Semi Stand KIT D-Sub Cable Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Down-Up buttons) / Channel buttons Moves from one menu item to another vertically or adjusts selected menu values. / When OSD is not on the screen, press the button to adjust channels.
Introduction [PC] → [DVI] → [AV] → [Component] → [HDMI]→ [MagicInfo] → [TV] Note MagicInfo supports the CXN-2 model only. D.MENU Opens the on-screen D.MENU. Power button [ ] Use this button for turning the LCD Display on and off. Brightness Sensor (Optional) Automatically detects the surrounding brightness it accordingly. This function is activated only on the models equipped with an auto brightness sensor.
Introduction POWER S/W ON [│ ] / OFF [O] Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB/COMPONENT IN (PC Video Connection Terminal) " Use a D-Sub Cable (15 pin D-Sub) PC mode (Analog PC) " Connect the RGB/COMPONENT IN port on the monitor to the COMPONENT port on the external device using the D-SUB to COMPONENT cable.
Introduction DVI/RGB/HDMI AUDIO IN(PC/DVI/ HDMI(PC) Audio connection terminal(input)) AV / COMPONENT AUDIO IN [R- AUDIO- L] Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [ R- AUDIO - L] port of the LCD Display. DVI OUT " Connect a monitor to another monitor through a DVI cable. " Connect the DVI OUT port on the monitor to the HDMI IN port on the other monitor using the DVI to HDMI cable.
Introduction COMMON INTERFACE This contains information on CAM inserted in the CI slot and displays it. When not inserting CI CARD in some channels, Scramble Signal is displayed on the screen. You can install the CAM anytime whether the TV is ON or OFF. SERVICE This is a reserved terminal used for servicing. ANT IN Connect the CATV cable or TV antenna cable to the " ANT IN" port on the rear side of the LCD Display. Make sure to use a TV antenna cable (sold separately) as the antenna cable.
Introduction Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on the model.
Introduction POWER OFF Number Buttons DEL / GUIDE button + VOL SOURCE D.MENU TOOLS Up-Down Left-Right buttons INFO COLOR BUTTONS TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV MENU RETURN EXIT MagicInfo 1. POWER Turns the product On. 2. OFF Turns the product Off. 3. Number Buttons 4. DEL ton / GUIDE but- Press to change the channel. The "-" button is used to select Digital channels. For example, channel 4-1. Electronic Program Guide (EPG) display. - This fuction does not work for this LCD Display.
Introduction 8. TOOLS Use to quickly select frequently used functions. 9. Up-Down buttons 10. Left-Right INFO 11. COLOR BUTTONS Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Current picture information is displayed on the upper left corner of the screen. Press to add or delete channels and to store channels to the favorite channel list in the “Channel List” menu. - This fuction does not work for this LCD Display. 12.
Introduction 18. MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. 19. RETURN Returns to the previous menu. 20. EXIT Exits from the menu screen. 21. MagicInfo MagicInfo Quick Launch Button. Mechanical Layout (400CX-2 ,400CXN-2) Mechanical Layout Installation Wall Mount VESA Bracket " When installing VESA, make sure to comply with the international VESA standards.
Introduction Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation " Contact a technician for installing the wall bracket. " SAMSUNG Electronics is not responsible for any damages to the product or persons if you elect to install the unit on your own. " This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Introduction 1. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. 2. A - Captive Screw B - Wall Bracket C - Hinge (Left) D - Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.
Introduction To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1. Remove the 4 screws on the back of the product. 2. Insert screw B into the plastic hanger. Notice " Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. " Be careful when installing the product on the bracket as fingers can be caught in the holes.
Introduction 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A - LCD Display B - Wall Bracket C - Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2.
Introduction Make sure to use the top center, and not the left or the right side of the product to adjust the angle. Mechanical Layout (460CX-2 ,460CXN-2) Mechanical Layout Installation VESA Bracket " When installing VESA, make sure to comply with the international VESA standards. " Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.
Introduction Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation " Contact a technician for installing the wall bracket. " SAMSUNG Electronics is not responsible for any damage to the product or persons if you elect to install the unit on your own. " This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Introduction When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. 2. A - Captive Screw B - Wall Bracket C - Hinge (Left) D - Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. A - 3.
Introduction To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1. Remove the 4 screws on the back of the product. 2. Insert the screw B into the plastic hanger. Notice " Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. " Be careful when installing the product on the bracket as fingers can be caught in the holes.
Introduction 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A - LCD Display B - Wall Bracket C - Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2.
Introduction Make sure to use the top center, and not the left or the right side of the product to adjust the angle.
Connections Connecting a Computer Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. Connect the power cord for your LCD Display to the power port on the back of the LCD Display. Turn on the power switch. There are several ways to connect the computer to the monitor.
Connections Using the HDMI (digital) output on the graphics card. " Connect the HDMI IN port on the monitor to the HDMI port on the PC using the HDMI cable. Note " When the HDMI cable to the PC, ensure that you select HDMI from both the Source List and Edit Name before selecting PC or DVI device so that normal PC screen and sound can be outputted. " Note that sound is only available when connected according to the option 2 that follows.
Connections 1. Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the LCD Display. Using a TV antenna cable (sold separately). " When using an interior antenna terminal: Check the antenna terminal on the wall first and connect the antenna cable. " When using an outdoor antenna: If you are using an outdoor antenna, use a professional for installation if possible. " To connect the RF cable to the antenna input terminal: Keep the copper wire portion of the RF cable straight.
Connections 2. Insert the CAM with the CI CARD installed into the common interface slot. (Insert the CAM in the direction of the arrow, right up to the end so that it is parallel with the slot.) 3. Check if you can see a picture on a scrambled signal channel. Connecting AV Devices 1. Connect the Video and [R-AUDIO-L] port of the DVD, VCR or DTV Set-Top Box to the Video and [R-AUDIO-L]port of the LCD Display. 2. Play the DVD, VCR or Camcorder with a DVD disc or tape inserted. 3.
Connections " For an explanation of Component video, consult your DVD or external device's user manual. Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV/COMPONENT AUDIO IN [R-AUDIOL] on the LCD Display . 2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display . 3.
Connections Connecting Using a DVI to HDMI Cable 1. Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable. 2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the DVI / RGB AUDIO IN terminal of the LCD Display. Connecting Using a DVI Cable 1.
Connections Connecting a DTV Set Top (Cable/Satellite) Box 1. Connect the Component to D-sub cable(sold separately) to the product's RGB/ COMPONENT IN port and the COMPONENT - PR, Y, PB ports on the Set-Top Box. 2. Connect a set of audio cables between the AV/COMPONENT AUDIO IN [R-AUDIOL] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note " Select Component using the SOURCE button on the front of the LCD Display or on the remote control.
Connections Note Connect the LAN cable. (Applicable to the CXN-2 model only) Connecting a USB device " You can connect USB devices such as a mouse or keyboard.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting " Do not use benzene, thinner or other flammable substances, or a wet cloth. " We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. " Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) " The user will be required to pay costs and related expenses for repairing damages caused.
Troubleshooting PC Mode Q: The LCD Display screen flickers. A: Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) TV Mode Q: TV screen is blurred or shows noise signals. A: Check if the TV antenna connector is securely connected to the external antenna. (Refer to Connecting TV) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed.
Troubleshooting Q: Ghost images are shown in the picture. A: Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display. If not, reset them referring to the current Information under the LCD Display menu and Preset Timing Modes. Q: The image is too light or too dark. A: Adjust the brightness and contrast. (Refer to theBrightness, Contrast) Q: The screen color is inconsistent. A: Adjust color usingCustom under OSD Color Adjustment menu.
Troubleshooting Q: The sound is too high or too low. A: Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: The remote control buttons do not respond. A: Check the polarities (+/-) of the batteries. A: Check if the batteries are empty. A: Check if the power is on. A: Check if the power cord is securely connected.
Troubleshooting Q: How can I clean the outer case/LCD Panel? A: Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the LCD Display. Q: How can I play the video? A: The video supports the MPEG1 and WMV codecs only. Install the corresponding codec to play the video. Note that some of the codecs can be incompatible.
