SyncMaster 460UTn-2, 460UT-2, 460UTn-B, 460UT-B LCD Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product.
Safety Instructions DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT. • Otherwise, this may result in fire. Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature.
Safety Instructions When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it with a soft, dry cloth. • (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.
Safety Instructions If thunder or lightning is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.
Safety Instructions To avoid eyestrain, do not sit too close to the product. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces eye fatigue. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result in fire.
Safety Instructions The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery. Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.
Introduction Package Contents Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the holding the grooves on package. both sides of the package box. Remove the Styrofoam and vinyl cover. Note • After unpacking the package, make sure to check the contents of the package. • Store the packaging box in case you need to move the Product later. • If any items are missing, contact your dealer.
Introduction Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all locations) Cables Power Cord D-Sub Cable MagicInfo Software CD, MagicInfo Manual CD (Applicable to the 460UTn-2, 460UTn-B model only) Others Remote Control Batteries (AAA X 2) (BP59-00138B) (Not available in all locations) Sold separately Semi Stand KIT LAN Cable USB Cable (Applicable to the 460UTn-2, 460UTn-B model only) 9
Introduction Sold separately RGB to BNC Cable Wall Mount KIT RGB to COMPONENT Cable Network Box (Applicable to the 460UT-2, 460UT-B model only) TV Tuner Box Your LCD Display Front SOURCE button Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [PC] → [DVI] → [AV] → [Component] → [HDMI1] → [HDMI2] → [DisplayPort] → [MagicInfo] → [TV] Note • A TV tuner box (sold separately) must be connected to use the TV.
Introduction Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on the LCD Display. Rear Note See the "Connections" section for details about cable connections. The LCD Display's configuration at the back may vary slightly depending on the model.
Introduction • Connect a DVI or DVI-HDMI cable to [DVI OUT (LOOPOUT)] on the product and [DVI IN] or [HDMI IN] on another monitor. • HDMI and network signals sent via the [DVI OUT(LOOPOUT)] port are displayed on the second display which has the [DVI IN] port. Note • The Loopout function can be used to duplicate the screen of the primary display. Connect [DVI OUT] on the primary display to [DVI IN] or [HDMI] on another display.
Introduction Connect a DP cable to [DP IN] on the product and DP IN on another display. R] AV/COMPONENT AUDIO IN [L-AUDIO- Connect the [AV/COMPONENT AUDIO IN [L-AUDIO-R]] port on the monitor to the audio output port on the PC or on the external device using an audio cable. AV IN Connect the [AV IN] terminal of your monitor to the video output terminal of the external device using a VIDEO cable. AUDIO OUT Connect a headphone or an External speaker.
Introduction Note The MAGICINFO OUT port must be connected to the [HDMI IN 2 (MAGICINFO)] port. RJ 45 MDC (MDC PORT) MDC(Multiple Display Control) Program Port Connect the LAN cable to [RJ45 MDC] on the product and LAN on the PC. To use an MDC, the MDC program must be installed on the PC. Note Go to Multi Control and select RJ45 MDC as the MDC Connection.
Introduction USB (USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. Note Applicable to the 460UTn-2, 460UTn-B model only. Kensington Lock slot A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, refer to the User Manual supplied with the locking device for more information.
Introduction Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. POWER OFF Number Buttons DEL / GUIDE button + VOL SOURCE D.MENU TOOLS Up-Down Left-Right buttons INFO PC/DVI/HDMI/DP TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV MENU RETURN EXIT MagicInfo POWER Turns the product On/Off. OFF Turns the product Off.
Introduction SOURCE Selects a connected external input source or MagicInfo mode. Press the button to change the input signal SOURCE. Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time. D.MENU DTV menu display - This function does not work for this LCD Display. TOOLS Use to quickly select frequently used functions. - This function does not work for this LCD Display.
Introduction comes back on if MUTE or - VOL + is pressed in the Mute mode. CH/P In TV mode, selects TV channels. - This is activated when a TV tuner box is installed. Selects the TV mode directly. TV - This is activated when a TV tuner box is installed. MENU RETURN EXIT MagicInfo Opens the on-screen menu and exits from the menu or closes the adjustment menu. Returns to the previous menu. Exits from the menu screen. MagicInfo Quick Launch Button.
Introduction Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display.
Introduction Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Introduction There are two hinges(left and right). Use the correct one. 2. A- Captive Screw B- Wall Bracket C- Hinge (Left) D- Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. A3. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.
Introduction To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1. Remove the 4 screws on the back of the product. 2. Insert the screw B into the plastic hanger. Notice 3. • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes.
Introduction 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A- LCD Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2.
Introduction Make sure to use the top center, and not the left or the right side of the product to adjust the angle.
Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the [DVI IN] port on the back of your LCD Display and the DVI port on the computer.
Connections Note Select HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 as an input source when connected to the PC via an HDMI cable. To obtain normal picture and audio from the PC, HDMI2 (only with a 460UT-2, 460UT-B model) or HDMI1 must be selected before PC is selected in Edit Name. To enable audio when DVI Device is selected, be sure to establish the connection using step ( ). Connect the Audio cable for your LCD Display to the AUDIO port on the back of the LCD Display.
Connections Connect between the [DVI OUT(LOOPOUT)] port on the LCD Display and the input port on another monitor using a DVI cable. Connect between the [AUDIO OUT] port on the LCD Display and the audio input port on another monitor using a stereo cable. Note Select DVI Mode as an input source for the external monitor connected to [DVI OUT]. DVI OUT does not support HDCP. Connecting AV Devices 1.
Connections Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Display . 2. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [L-AUDIO-R]] on the LCD Display . 3. Press SOURCE on the product or remote control and select "AV". 4.
Connections Connecting Using a HDMI Cable 1. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] (only with a 460UT-2, 460UT-B model) or [HDMI IN 1] on the product and the HDMI output port on a digital device. 2. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2(only with a 460UT-2, 460UT-B model)" Note In HDMI mode, only PCM format audio is supported.
Connections nect the opposite jack to the [RGB/DVI/DP/HDMI AUDIO IN] terminal of the LCD Display. 3. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2(only with a 460UT-2, 460UT-B model)" Connecting a DVD Player Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the DVD player. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [L-AUDIO-R]] on the LCD Display and the AUDIO OUT jacks on the DVD player.
Connections Connecting a DTV Set Top (Cable/Satellite) Box Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the Set Top Box. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [L-AUDIO-R]] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note • Press SOURCE on the product or remote control and select "Component". • For an explanation of Component video, see your Set Top Box owner's manual.
Connections Connecting a LAN Cable 1. Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC. Note Applicable to the 460UTn-2, 460UTn-B model only. Connecting a USB devices 1. You can connect USB devices such as a mouse or keyboard. Note Applicable to the 460UTn-2, 460UTn-B model only.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CDROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. (Start) and "Control Panel". Then, double-click on "Appearance and PersonalClick ization". 3. Click "Personalization" and then "Display Settings". 4.
Using the Software If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will...", then click "Next" and then click "Have disk".
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see the following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is certified by Microsoft, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver), then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location...", then click "Next" button. 8. Click the "Have Disk" button. 9. Specify A:\(D:\driver), then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11.
Using the Software 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. MDC(Multiple Display Control) Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MDC System installation program. Note If the screen for installing the software does not appear, install it using the MDC System execution file in the MDC folder of the CD-ROM. 3. If the installation wizard screen does appear, click "Next." 4.
Using the Software Installation Problems The installation of MDC can be affected by such factors as the video card, motherboard and the network environment. Uninstall The MDC program can be removed only by using the "Add or Remove Programs" option of the Windows® Control Panel. Perform the following steps remove MDC. Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select MDC System from the list and then click the "Add/Delete" button.
Introduction Unlike the previous method which used the serial data communication specifications RS-232C, an Ethernet function has been added. Connect the first display device and the PC by entering the IP address. To connect to another display device, use an RS-232C serial cable. Refer to the figure above. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Lamp Control Add a Device Display Selection Remote Control All Safety Lock Control Tools Fault Device Alert OSD Display 1. Use the main icons to switch into each screen. 2. You can add a device by entering the IP address configured on the monitor. 3. Allows you to enable or disable the remote control signal receiving function of the display unit. 4. Set the Safety Lock function.
1. Enter the IP address of the monitor to be connected and press the Add button to add the IP address. If you click the OK button, adding the monitor is completed. System 1. Click System in the main menu to open the system adjustment screen. Info Grid shows some basic information necessary to System. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Selects displays you want to adjust using the Select All button or checkboxes.
System allows controlling some of the functions of the selected display. 1) Power On/Off - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (If you deselect a single display or all displays, the default value 10 will be restored.) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display.
- Sets whether the Source OSD will be displayed to indicate when the Source is changed. 2) Not Optimum Mode OSD - Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported. 3) No Signal OSD - Sets whether the No Signal OSD will be displayed to indicate when there is no signal. 4) MDC OSD - Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC.
• PC Mode Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) DTV - Changes the Input Source of the selected display to DTV. 6) AV - Changes the Input Source of the selected display to AV.
- Changes the Input Source of the selected display to Component. 9) MagicInfo - The Input source of MagicInfo works only on MagicInfo model. 10) HDMI1/HDMI2 - Changes the Input Source of the selected display to HDMI. 11) DP - Switches the input source for the selected display to DP. 12) Channel - Channel arrow appears when the Input Source is TV. HDMI2 may not be supported depending on the product. DP may not be supported depending on the product.
Image Size TV, AV, S-Video, Component, DVI(HDCP), HDMI1, HDMI2, DTV 1. Click Image Size of the main icons and the Image Size control screen appears. Info Grid shows some basic information necessary to Image Size Control. 1) To adjust Image Size in TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV mode, click the Video Source tab. Select the display you want to adjust by using the Select All button or by checking the checkbox.
Info Grid shows some basic information necessary to Time Control. 1) Clock Set - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) Timer - Sets up Timer1, Timer2, Timer3 and Holiday Management. 3) Shows whether Timer is activated. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model. Time Control is available only for the displays for which the power status is ON.
5) Holiday - Applies the Holiday Management function to the Timer. 6) Repeat - Available selections include Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, and Manual. z z z z z z Once : The Timer goes off only once. EveryDay : EveryDay: The Timer repeats daily. Mon~Fri : The Timer repeats from Monday through Friday. Mon~Sat : The Timer repeats from Monday through Saturday. Sat~Sun : Sat~Sun: The Timer goes off on Saturday and Sunday. Manual : Select a day of the week you want the Timer to go off. 2.
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small. 5) Double 1 - Turns on the PIP of the selected display and changes the size to Double 1.
Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) TV - Changes the source of the PIP of the selected display to TV. 6) DTV - Changes the source of the PIP of the selected display to DTV.
Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will be displayed if one of the connected monitors is selected, and the default settings will be displayed if all monitors are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode. 1) Picture - Available only for TV, AV, S-Video, Component, HDMI1, HDMI2, DTV. 2) Contrast - Adjusts Contrast of the selected display.
Basic information required to adjust settings is displayed. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode. 1) Picture PC - Available only for PC, BNC, DVI and DP. 2) Contrast - Adjusts Contrast of the selected display.
Basic information required to adjust Audio is displayed in the display window. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode. 1) Audio - Controls audio settings for all input sources. 2) Bass - Adjusts Bass of the selected display.
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal. The Maintenance Control feature is available only for the displays whose power status is ON. The Input source of MagicInfo works only on MagicInfo model.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. - Allows you to adjust the backlight of the selected display regardless of the time. The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall Control - Video Wall properties can be configured. 1) On / Off - Turns on/off the Video Wall function of the selected display. 2) Format - The format can be selected to see a divided screen.
z Natural 3) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection. z The place will be set up by pressing a number in the selected mode. z The maximum number of monitors that can be arranged: Horizontal X Vertical = 100 z Up to 15 monitors can be arranged in a row.
Adjusting the LCD Display Input Available Modes • PC / DVI / DP • AV • Component • HDMI • MagicInfo For an 460UT-2, 460UT-B model, MagicInfo can only be enabled when a network box is connected. Source List Use to select PC, HDMI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. Component 5. HDMI1 6. HDMI2 7. DisplayPort 8. MagicInfo 9. TV PIP Note The PIP function is not available when Video Wall is On.
Adjusting the LCD Display When external AV devices such as VCRs or DVDs are connected to the LCD Display , PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off/On) Note • PIP turns off when the LCD Display is switched to an external source. • If you select , , in Size, Position and Transparency will not be activated. PIP Turns the PIP Screen Off/On. • Off • On Source Note For PC, this is deactivated if the cable is disconnected.
Adjusting the LCD Display Size Changes the Size of the PIP window. Position Changes the Position of the PIP window. Transparency Adjusts the Transparency of PIP windows.
Adjusting the LCD Display Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo / DHR / PC / DVI Devices Note • The displayed devices differ depending on the external input mode. • When connecting a PC to the HDMI terminal, set Edit Name to PC. In other cases, set Edit Name to AV.
Adjusting the LCD Display Note • By adjusting the picture using the Custom function, MagicBright will change to Custom mode. • Not available when Dynamic Contrast is set to On. 1. Contrast Adjusts the Contrast. 2. Brightness Adjusts the Brightness. 3. Sharpness Adjusts the Sharpness. 4. Gamma Adjust the mid-range brightness (Gamma) for the picture.
Adjusting the LCD Display Note Not available when Dynamic Contrast is set to On. The color tones can be changed. 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled. If you set the Color Tone to Off, the Color Control function is disabled Color Control Adjusts individual Red, Green, Blue color balance. Note Not available when Dynamic Contrast is set to On. 1. Red 2. Green 3. Blue Color Temp.
Adjusting the LCD Display Note Available in PC mode only. Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Position Adjusts the screen location horizontally and vertically.
Adjusting the LCD Display Signal Balance Selects either On or Off with the signal balance. Signal Control Note Available when Signal Balance is set to On. 1. R-Gain 2. G-Gain 3. B-Gain 4. R-Offset 5. G-Offset 6. B-Offset Size The Size can be switched. 1.
Adjusting the LCD Display 2. 4:3 HDMI Black Level When watching with a DVD or set-top box connecting to the product via HDMI, image quality deterioration (black level, lower-quality contrast, lighter color tone, etc.) may occur depending on the connected external device. 1. Normal 2. Low Note For Timing which can be used for both the PC and the DTV in HDMI mode, HDMI Black Level will be activated. PIP Picture Adjusts the PIP Screen Settings. Note • 1.
Adjusting the LCD Display Note Only enabled when the PIP input source is HDMI. 5. Tint Adds a natural tone to the PIP window. Note The Tint slider is only displayed when the input signal is NTSC and is only enabled when the PIP input source is HDMI. Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note Disabled when PIP is set to On.
Adjusting the LCD Display Picture [ AV / HDMI / Component Mode] Available Modes • PC / DVI / DP • AV • Component • HDMI • MagicInfo For an 460UT-2, 460UT-B model, MagicInfo can only be enabled when a network box is connected. Mode The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Dynamic, Standard, Movie, or Custom can be activated. Note Not available when Dynamic Contrast is set to On. 1. Dynamic 2. Standard 3.
Adjusting the LCD Display Brightness Adjusts the Brightness. Sharpness Adjusts the picture Sharpness. Color Adjusts the picture Color. Tint Adds a natural tone to the display. Note Operates only if the video signal is NTSC. Color Tone The color tones can be changed. The individual Color components are also user adjustable. Note Not available when Dynamic Contrast is set to On. 1. Off 2. Cool2 3. Cool1 4. Normal 5. Warm1 6.
Adjusting the LCD Display Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function is disabled. Color Temp. Color temp. is a measure of the 'warmth' of the image colors. Note When Dynamic Contrast mode and Color Tone are Off, this function is activated. Size The Size can be switched. 1. 16:9 - Sets the picture to 16:9 wide mode. 2. Zoom 1 - Magnifies the size of the picture on the screen. 3. Zoom 2 - Magnifies the size of the picture more than Zoom 1. 4.
Adjusting the LCD Display Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1. Off 2. On Note Digital NR function is not available for all resolutions. HDMI Black Level When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
Adjusting the LCD Display PIP Picture Adjusts the PIP Screen Settings. Note Available Modes: PIP On 1. Contrast Adjusts the Contrast of the PIP window on the screen. 2. Brightness Adjusts the Brightness of the PIP window on the screen. 3. Sharpness Adjusts the Sharpness of the PIP window on the screen. Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note Disabled when PIP is set to On.
Adjusting the LCD Display Picture Reset Reset the screen settings. Sound Available Modes • PC / DVI / DP • AV • Component • HDMI • MagicInfo For an 460UT-2, 460UT-B model, MagicInfo can only be enabled when a network box is connected. Mode The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4.
Adjusting the LCD Display Custom The sound settings can be adjusted to suit your personal preferences. Note • You can hear the sound even when sound value is set to 0. • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass Emphasizes low frequency audio. Treble Emphasizes high frequency audio. Balance Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume Reduces the difference in volume control between broadcasters. 1. Off 2.
Adjusting the LCD Display experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. 1. Off 2. On Sound Select Enable the sound of either the primary or secondary display in PIP mode. Note Available when PIP is set to On. 1. Main 2. Sub Sound Reset Reset the sound settings.
Adjusting the LCD Display Language You can choose one of 13 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. Clock Set Current Time Setting. Sleep Timer Turns the LCD Display off automatically at certain times. 1. Off 2. 30 3. 60 4. 90 5.
Adjusting the LCD Display 6. 150 7. 180 Timer1 / Timer2 / Timer3 You can set the LCD display to automatically turn on or off at a specified time. Note • Only enabled when the clock is set using the Clock Set menu. • The Manual option allows you to select a day of the week. Holiday Management • Add You can register holidays. • Delete Selected You can delete selected holidays. Note • Only enabled when registered holidays are selected. • More than one holiday can be selected and deleted.
Adjusting the LCD Display • Delete All You can delete all the registered holidays. Menu Transparency Change the transparency of the background of the OSD. 1. High 2. Medium 3. Low 4. Opaque Safety Lock Change PIN The password can be changed. The preset password for the LCD Display is "0000". Note If you forgot your password, press the remote buttons MUTE → 1 → 8 → 6 → On to reset the password to "0000.
Adjusting the LCD Display Lock On → [0∼9] → [0∼9] → [0∼9] → [0∼9] This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings. Energy Saving This feature adjusts the power consumption of the unit in order to save energy. 1. Off 2. On Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen.
Adjusting the LCD Display • Off • On Format The Format can be selected to see a divided screen. • Full Provides a full screen without any margins. • Natural Displays a natural image with the original aspect ratio intact. Horizontal Sets how many parts the screen should be divided horizontally. Fifteen adjustment levels: 1~13. Vertical Sets how many parts the screen should be divided vertically. Fifteen adjustment levels: 1~13.
Adjusting the LCD Display Screen Position The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Position. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. • The screen can be split into a maximum of 100 sub-screens.
Adjusting the LCD Display Horizontal Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time Set the time interval for performing the horizontal or vertical movement, respectively. Timer Timer You can set the timer for Screen Burn Protection.
Adjusting the LCD Display • Off • On Mode You can change the Safety Screen Type. • Bar • Eraser • Pixel Period Use this function to set the execution period for each mode set in the timer. Time Within the set period of time specify a time for execution.
Adjusting the LCD Display This function prevents after-images on the screen by moving long black and white vertical lines. Eraser This function prevents after-images on the screen by moving a rectangular pattern. Pixel This function prevents after-images by moving many pixels on the screen. Side Gray Select the brightness of the grey for the screen background.
Adjusting the LCD Display When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x 768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. Note Available in PC mode only. 1. Off 2. 1024 X 768 3. 1280 X 768 4. 1360 x 768 5.
Adjusting the LCD Display Advanced Settings Configures the settings more elaborately. Fan & Temperature Prevents the product from overheating using Fan Speed Setting and Temperature Control. Fan Control Selects auto or manual for the fan speed settings. Fan Speed Setting Sets the fan speed within a range of 0 and 100. Note Enabled when Fan Control is set to Manual. Temperature Control Sets a maximum temperature to prevent the product from overheating.
Adjusting the LCD Display Current Temperature Shows the current temperature of the product. Auto Power Enables or disables Auto Power for the product. • Off • On Note When Auto Power is On, the product will power on automatically as soon as it is connected to power. Button Lock Locks or unlocks the monitor control buttons on the product.
Adjusting the LCD Display User Auto Color 1. Auto Color Automatically adjusts the colors. 2. Reset Resets the color settings. Note Enabled only in PC mode. Standby Control Sets the standby mode, which will be activated when no input signal is detected. • Off A message will read if no input signal is detected. • On Power-saving mode will be activated if no input signal is detected.
Adjusting the LCD Display Lamp Schedule Enables the Lamp value to be adjusted to a user-specified value at a specified time in MDC mode. OSD Display Displays or hides a menu item on the screen.
Adjusting the LCD Display • Off • On MDC OSD • Off • On Software Upgrade Performs a software upgrade. Note • Enabled only in DVI, HDMI, HDMI2, or MagicInfo mode. • Enabled only with an aspect ratio of 16:9. Setup Reset Reset all the values for a setting. Reset All Reset all the settings for the display.
Adjusting the LCD Display For an 460UT-2, 460UT-B model, MagicInfo can only be enabled when a network box is connected. Multi Control Assigns an individual ID to the SET. • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. • MDC Connection Selects a port to receive the MDC inputs from. • • Communicates with the MDC via a RS232C MDC cable.
Adjusting the LCD Display For an 460UT-2, 460UT-B model, MagicInfo can only be enabled when a network box is connected. Note • The remote control can be used to select MagicInfo. However, it is recommended to use a separate USB keyboard to utilize MagicInfo fully. • For MagicInfo in Device mode, moving external devices while booting may cause errors. Set up external devices only if the LCD Display turns on. • Do not unplug the LAN cable used for the network (ex: video display).
Adjusting the LCD Display You can select an Application to be executed in your computer when Windows starts. 2. Select TCP/IP - step 2 In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3.
Adjusting the LCD Display When using multiple languages, you can choose and set a specific language among them. 4. Select Screen Type - step 4 You can select which rotation type will be applied to your device. 5.
Adjusting the LCD Display Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop. The icon will appear.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user is responsible for any damage caused by using these substances. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer.
Troubleshooting A: Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: "Check Signal Cable" message.
Troubleshooting Q: The screen color is inconsistent. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The Power Indicator blinks. A: The LCD Display is currently saving the changes made in the settings to the OSD memory.
Troubleshooting A: Check if the batteries are empty. A: Check if the power is on. A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity. Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. Q&A Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.
Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Specifications General General Model Name SyncMaster 460UTn-2 / 460UT-2 / 460UTn-B / 460UT-B LCD Panel Size 46 inches (116 cm) Display area 1018.35 mm (H) x 572.54 mm (V) Pixel Pitch 0.746 mm (H) x 0.746 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7M Resolution Optimum resolution 1366 x 768 @ 60 Hz Maximum resolution 1920 x 1080 @ 60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.
Specifications Dimensions (W x H x D) / Weight 460UT-2 1025.7 mm x 579.8 mm x 130.0 mm (40.4 x 22.8 x 5.1 inches) / 26.3 Kg (58.0 Ibs) 460UTn-B 1025.7 mm x 579.8 mm x 130.0 mm (40.4 x 22.8 x 5.1 inches) / 20.8 Kg (45.9 Ibs) 460UT-B 1025.7 mm x 579.8 mm x 130.0 mm (40.4 x 22.8 x 5.1 inches) / 19.3 Kg (42.
Specifications Class A (Information Communication equipment for industrial use) : 460UTn-2, 460UTn- B Attention dealers and users. This device is registered for EMC requirements for industrial use (Class A) and can be used in areas other than general households. Class B(Information Communication equipment for residential use) : 460UT-2, 460UT-B This device is registered for EMC requirements for home use (Class B). It can be used in all areas.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Fre- Pixel Clock quency (Hz) (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.
Information For a Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFTLCD. • Resolution: 1366 x 768 • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. • The Image Retention Free function applied to the product is recommended. - For detailed configuration procedures, refer to the back page.
Information Rotate the Color Information with 2 different colors every 30 minutes. • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically • Use Bright colors with little difference in luminance.
Information Apply the Screen Erasing function on Product • Apply the Screen Erasing function - Symptom: 2 Vertical blocks move while erasing the display 94
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com Latin America ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG(726-7864) http://www.samsung.
Appendix Europe EIRE 0818 717100 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com FINLAND 030 - 6227 515 http://www.samsung.com FRANCE 01 48 63 00 00 http://www.samsung.com GERMANY 01805 SAMSUNG http://www.samsung.com (726-7864, € 0,14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com LATVIA 8000-7267 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LUXEMBURG 261 03 710 http://www.
Appendix Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.com CHINA 400-810-5858 http://www.samsung.com 010-6475 1880 HONG KONG (852) 3698 - 4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 3030 8282 http://www.samsung.com 1800 110011 1800 3000 8282 1800 266 8282 INDONESIA 0800-112-8888 http://www.samsung.com 021-5699-7777 JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com NEW ZEALAND 0800 SAMSUNG (0800 726 http://www.
Appendix Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle.
Appendix Correct disposal of batteries in this product - Europe only (Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.