SyncMaster 700DRN-A LCD Display User Manual
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product.
Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor. • Otherwise, this may result in damage to the screen display. Install your product in a well ventilated location.
Safety Instructions Others The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves. • Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center. If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. • Otherwise, this may result in electric shock or fire.
Safety Instructions Set a resolution and frequency appropriate to the product. • Otherwise, your eyesight may be damaged. When using headphones or earphones, do not turn the volume too high. • Having the sound too loud may damage your hearing. If you continually move closer to the product screen, your eyesight may be failing. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes.
Safety Instructions When replacing the battery, insert it with right polarity (+, -). • Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid. Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time. • Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.
Safety Instructions Refer to the Cable Safety Specifications. • UL specifications - Use a cable with 14 AWG or more • KS specification - Use a cable with 20.SQ or more • IEC specification - Use a cable with 2.
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Introduction Cables D-Sub Cable GND Cable (3) Others Shock Sensor Remote Control Batteries (AAA X 2) (Not available in all locations) Sold separately DVI Cable LAN Cable Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values.
Introduction Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume. ENTER button [ENTER] Activates a highlighted menu item. SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time.
Introduction RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port PC / DVI / HDMI AUDIO IN (PC/DVI/ HDMI Audio Connection Terminal (Input)) HDMI IN Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable.
Introduction DC OUT Make sure to use connecting DC-OUT terminal to the authorized TV-Tuner Box[SBBDT*]. Otherwise, this may result in damage to the product. AV IN [VIDEO] (VIDEO Connection Terminal) Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.
Introduction 1. Connect the GND wires to the bottom part of both sides of the product and then to the back of the product as shown by figure ( 2. ). Connect the other side of the GND wires to the ground box when indoors or to the ground pole that has been pushed into the ground when outdoors. Note The ground (GND) is used to prevent product noise and to protect people from electric shock due to electric leakage.
Introduction Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. Note The TV menu is available when a TV tuner box is installed. POWER OFF Number Buttons DEL button + VOL MUTE TV/DTV MENU INFO Color Buttons TTX/MIX STILL AUTO S.MODE MDC LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT SRS MagicInfo P.
Introduction PIP SWAP 1. POWER Turns the product On. 2. Off Turns the product Off. 3. Number Buttons Press to change the channel. 4. DEL The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV. button 5. + VOL - Adjusts the audio volume. 6. Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. MUTE 7.
Introduction Changing the SOURCE is only allowed for external devices that are connected to the monitor at the time. 19. 20. ENTER/PRE-CH CH/P This button is used to return to the immediately previous channel. In TV mode, selects TV channels. 21. D.MENU DTV menu display 22. GUIDE Electronic Program Guide (EPG) display. 23. RETURN 24. Up-Down Left-Right buttons 25. 26. EXIT SRS Returns to the previous menu.
Introduction 30. PIP Every time you press the button, a PIP screen appears. - This fuction does not work for this LCD Display. 31. SWAP Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. - This fuction does not work for this LCD Display.
Using the Software MDC (Multi-Display Channel) Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MDC installation file. Note If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MDC executable file on the CD. 3. When the Installation Shield Wizard window appears, click "Next". 4. Select "I agree to the terms of the license agreement" to accept the terms of use. 5. Click "Install". 6.
Using the Software Using MDC
Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Select Button Remocon Info Grid Safety Lock Display Selection Port Selection Control Tools 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4. The setting for the PC Serial Port can change. The original value is COM1. 5.
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 4. The selected port is stored in the program and used for the next program as well. Power Control 1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display.
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display. When selecting one set at a time, turn on the Mute function for the selected set.
Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) DTV - Changes the Input Source of the selected display to DTV. 6) AV - Changes the Input Source of the selected display to AV.
Info Grid shows some basic information necessary to Image Size Control. 1) ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI. 5) PC Source - When you click Image Size, the PC Source tab first appear. - The Image Size Control button controls Image Size available for PC, BNC, DVI.
Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source. 3) Switch Image Size of the selected display randomly.
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display. 4) Shows the On Time settings. 5) Shows the Off Time settings.
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small. 5) Double 1 - Turns on the PIP of the selected display and changes the size to Double 1.
Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) AV - Changes the source of the PIP of the selected display to AV.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM." 1) Picture - Available only for TV, AV, S-Video, Component, HDMI, DTV.
1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM.
Settings Audio 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM.
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection. z The place will be set up by pressing a number in the selected mode.
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 25 . 2. The display you wish to control does not appear on the other Control Info Grids - Check to see if the display power is ON.
Adjusting the LCD Display Input Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note The TV menu is available when a TV tuner box is installed. Source List MENU → ENTER → [Input] → ENTER → [Source List] → , → ENTER Use to select PC, DVI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. HDMI 5. MagicInfo 6. TV Note • The direct button on the remote control is the 'SOURCE' button.
Adjusting the LCD Display → , → ENTER Name the input device connected to the input jacks to make your input source selection easier. VCR, DVD, Cable STB, HD STB, Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR, PC Picture [PC / DVI / MagicInfo Mode] Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note The TV menu is available when a TV tuner box is installed.
Adjusting the LCD Display 1. Entertain High brightness For watching motion pictures such as a DVD or VCR. 2. Internet Medium brightness For working with a mixture of images such as texts and graphics. 3. Text Normal brightness For documents or works involving heavy text. 4. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
Adjusting the LCD Display Sharpness MENU → → ENTER → [Picture] → [Sharpness] → , → ENTER → [Custom] → → → ENTER → → ENTER Adjusts the Sharpness. Color Tone MENU → → , → ENTER → [Picture] → → →ENTER → [Color Tone] → ENTER The color tones can be changed. (Not available in Dynamic Contrast mode of On.) 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled.
Adjusting the LCD Display Red MENU → → [Red] → , → ENTER → [Picture] → → → → ENTER → [Color Control] → ENTER → ENTER Green MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] → → ENTER → [Green] → , → ENTER Blue MENU → → ENTER → [Picture] → → ENTER → [Blue] → , → → → ENTER → [Color Control] → → → ENTER Color Temp. MENU → → , → ENTER → [Picture] → → → → ENTER → [Color Temp.] → ENTER Color Temp. is a measure of the 'warmth' of the image colors.
Adjusting the LCD Display Coarse MENU → → ENTER → [Picture] → → [Coarse] → , → → → → ENTER → [Image Lock] → ENTER → ENTER Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine MENU → → ENTER → [Picture] → ENTER → [Fine] → , → → → → ENTER → [Image Lock] → → → ENTER Removes noise such as horizontal stripes.
Adjusting the LCD Display (Not available in Dynamic Contrast mode of On.) Note The direct button on the remote control is the 'AUTO' button. Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable. MENU → ance] → ENTER → [Picture] → → → → → → → ENTER → [Signal Bal- (Available in PC mode only) (Not available in Dynamic Contrast mode of On.
Adjusting the LCD Display MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → ENTER → → [Signal Control] → → → ENTER→ [B-Gain] → , 4. → ENTER R-Offset MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → ENTER → → [Signal Control] → → → → ENTER→ [R-Offset] → , 5. → ENTER G-Offset MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → ENTER → → [Signal Control] → → → → → ENTER→ [G-Offset] → , 6.
Adjusting the LCD Display 2. 4:3 Dynamic Contrast MENU → → ENTER → [Picture] → → → → → → → → → ENTER → [Dynamic Contrast] → → ENTER , Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2.
Adjusting the LCD Display Note The TV menu is available when a TV tuner box is installed. Mode MENU → → , → ENTER → [Picture] → ENTER → [Mode] → ENTER The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Dynamic, Standard, Movie, or Custom can be activated. (Not available in Dynamic Contrast mode of On.) 1. Dynamic 2. Standard 3. Movie 4. Custom Note The direct button on the remote control is the 'P.MODE' button.
Adjusting the LCD Display Brightness MENU → ness] → , → ENTER → [Picture] → → ENTER → [Custom] → → ENTER → [Bright- → ENTER Adjusts the Brightness. Sharpness MENU → → ENTER → [Picture] → [Sharpness] → , → ENTER → [Custom] → → → ENTER → → ENTER Adjusts the picture Sharpness. Color MENU → [Color] → , → ENTER → [Picture] → → ENTER → [Custom] → → → → ENTER → → ENTER → [Custom] → → → → → ENTER → ENTER Adjusts the picture Color.
Adjusting the LCD Display → , → ENTER The color tones can be changed. The individual Color components are also user adjustable. (Not available in Dynamic Contrast mode of On.) 1. Off 2. Cool2 3. Cool1 4. Normal 5. Warm1 6. Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function is disabled. Color Temp. MENU → → , → ENTER → [Picture] → → → → ENTER → [Color Temp.] → ENTER Color Temp. is a measure of the 'warmth' of the image colors.
Adjusting the LCD Display 3. Zoom 2 4. 4:3 5. Just Scan (Not available in Dynamic Contrast mode of On.) Note The Zoom1, Zoom2 are not available HDMI. The Just Scan are available in HDMI. Digital NR (Digital Noise Reduction) MENU → → , → ENTER → [Picture] → → → → → → ENTER → [Digital NR] → ENTER Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1. Off 2.
Adjusting the LCD Display Dynamic Contrast MENU → → ENTER → [Picture] → Contrast ] → → → → → → → → ENTER → [Dynamic → ENTER , Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Brightness Sensor MENU → → ENTER → [Picture] → [Brightness Sensor] → , → → → → → → → → ENTER → →ENTER Brightness Sensor is to automatically detect distribution of inputted visual signal and adjust to create optimum brightness. 1.
Adjusting the LCD Display Mode MENU → → , → → ENTER → [Sound] → ENTER → [Mode] → ENTER The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4. Speech Selects Speech when watching a show that is mostly dialogue (i.e., news). 5.
Adjusting the LCD Display Treble MENU → → , → → ENTER → [Sound] → → ENTER → [Custom ]→ →ENTER→ [Treble] → ENTER Emphasizes high frequency audio. Balance MENU → ance] → , → → ENTER → [Sound] → → ENTER → [Custom ]→ → →ENTER→ [Bal- → ENTER Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume MENU → → , → → ENTER → [Sound] → → → ENTER → [Auto Volume] → ENTER Reduces the difference in volume control between broadcasters. 1. Off 2.
Adjusting the LCD Display perience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. 1. Off 2. On Setup Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note The TV menu is available when a TV tuner box is installed. Language MENU → → , → → → ENTER → [Setup] → ENTER → [Language ] → ENTER You can choose one of 13 languages. Note The language chosen affects only the language of the OSD.
Adjusting the LCD Display Clock Set MENU → Set] → , / , → → → ENTER → [Setup] → → ENTER → [Time ] → ENTER→ [Clock → ENTER Current Time Setting. Sleep Timer MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → ENTER→ [Sleep Timer] → , → ENTER Turns the LCD Display off automatically at certain times. 1. Off 2. 30 3. 60 4. 90 5. 120 6. 150 7.
Adjusting the LCD Display → , → ENTER / , Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically. Off Timer MENU → → → → ENTER → [Setup] → → [Off Timer] → , → ENTER → [Time ] → → → → ENTER → ENTER / , Turns the LCD Display off automatically at a preset time.
Adjusting the LCD Display Safety Lock PIN MENU → → → → ENTER → [Setup] → → → → ENTER → [Safety Lock PIN ] → [0~9, 0~9, 0~9, 0~9] → [0~9, 0~9, 0~9, 0~9] → [0~9, 0~9, 0~9, 0~9] The password can be changed. Energy Saving MENU → → , → → → ENTER → [Setup] → → → → → ENTER → [Energy Saving] → ENTER This feature adjusts the power consumption of the unit in order to save energy. 1. Off 2.
Adjusting the LCD Display 1. Normal 2. Low Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. When the Video Wall is on, you can adjust the Video Wall screen setting. MENU → Wall ] → → → ENTER → [Setup] → → → → → → → ENTER → [Video Note When Video Wall is running, the Auto Adjustment, Image Lock, and Size functions are not available.
Adjusting the LCD Display 1. Full Provides a full screen without any margins. 2. Natural Displays a natural image with the original aspect ratio intact. Horizontal MENU → → → → ENTER → [Setup] → → → → Wall ]→ → → ENTER → [Horizontal] → , → → → ENTER → [Video → → ENTER → [Video → → ENTER → [Video → ENTER Sets how many parts the screen should be divided horizontally. Five adjustment levels: 1, 2, 3, 4, and 5.
Adjusting the LCD Display The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. Safety Screen The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time. • The Safety Screen function scrolls the screen for the specified period of time.
Adjusting the LCD Display Horizontal Dot MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → → ENTER → [Horizontal Dot] → , → ENTER Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical Line MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → → → ENTER → [Vertical Line] → , → ENTER Sets how many pixels the screen moves vertically.
Adjusting the LCD Display Timer Timer MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → ENTER → [Timer] → , → ENTER You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish. 1. Off 2.
Adjusting the LCD Display Use this function to set the execution period for each mode set in the timer. Time MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → → → → ENTER → [Time] → , → ENTER Within the set period of time specify a time for execution.
Adjusting the LCD Display Eraser MENU → → → → ENTER → [Setup] → → → → [Safety Screen] → → → → →ENTER → [Eraser] → → → → ENTER → This function prevents after-images on the screen by moving a rectangular pattern.
Adjusting the LCD Display → , → ENTER Adjusts the Power On time for the screen. Caution: Set the Power On time to be longer to avoid overvoltage. Side Gray MENU → → → → ENTER → [Setup] → → → → ENTER → [Side Gray] → , → → → → → → → → ENTER Select the brightness of the grey for the screen background. 1. Off 2. Light 3. Dark Reset Reverts the product settings to factory defaults. The Reset function is only available when PC / DVI is being used.
Adjusting the LCD Display Note Available in PC mode only Note The Reset function is not available when Video Wall is On. Color Reset MENU → → → → ENTER → [Setup] → → → → → ENTER → [Reset ]→ → ENTER → [Color Reset ] → , → → → → → → → → ENTER OSD Rotation MENU → → → → ENTER → [Setup] → → → → → ENTER → [OSD Rotation ] → , → → → → → → → → → → → → → → → → → ENTER OSD Rotate 1. Landscape 2.
Adjusting the LCD Display Multi Control Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note The TV menu is available when a TV tuner box is installed. Multi Control Assigns an individual ID to the SET. MENU → → → → → ENTER → [Multi Control ] → ENTER → , → [0~9] • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.
Adjusting the LCD Display Note The TV menu is available when a TV tuner box is installed. Note • The remote control can be used to select MagicInfo. However, it is recommended to use a separate USB keyboard to utilize MagicInfo fully. • For MagicInfo in Device mode, moving external devices while booting may cause errors. Set up external devices only if the LCD Display turns on. • Do not unplug the LAN cable used for the network (ex: video display). Otherwise, the program (MagicInfo) may stop.
Adjusting the LCD Display You can select an Application to be executed in your computer when Windows starts. 2. Select TCP/IP - step 2 In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3.
Adjusting the LCD Display When using multiple languages, you can choose and set a specific language among them. 4. Select Screen Type - step 4 You can select which rotation type will be applied to your device. 5.
Adjusting the LCD Display Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop. The icon will appear.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances, or a wet cloth. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user will be required to pay costs and related expenses for repairing damages caused. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer.
Troubleshooting A: Check if the signal cable between the computer and the LCD Display is securely connected. Q: When the product’s internal cooling system operates, condensation may occur on the product surface under certain atmospheric temperature and humidity conditions. A: This symptom does not affect the product performance and will disappear as the atmospheric temperature and humidity conditions change.
Troubleshooting A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The power Indicator blinks green. A: The LCD Display is currently saving the changes made to the settings to the OSD memory. Q: The screen is blank and the power indicator light is steady green or blinks every 0.
Troubleshooting A: Check if the power is on. A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity. Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. Q&A Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.
Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Specifications General General Model Name SyncMaster 700DRN-A LCD Panel Size 70 " Diagonal (177 cm) Display area 1549.44 mm (H) x 871.56 mm (V) Pixel Pitch 0.807 mm (H) x 0.807 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7 M Resolution Optimum resolution 1920 x 1080@ 60 Hz (RB) Maximum resolution 1920 x 1080 @ 60 Hz (RB) Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB 0.7 Vp-p ±5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.
Specifications Environmental considerations Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This LCD Display can be installed on any Plug & Play compatible system. The interaction of the LCD Display and the computer systems will provide the best operating conditions and LCD Display settings.
Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFTLCD. • Resolution: 1920x1080 • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Change the Color Information periodically Note Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes.
Information • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically • Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement.
Information Note ( Please check CD's User Guide at "OSD Function", some model's will not available ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down.
Information - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not available )
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com/mx Latin America ARGENTINA 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.
Appendix Europe BELGIUM 02 201 2418 http://www.samsung.com/be (Dutch) http://www.samsung.com/ be_fr (French) CZECH REPUBLIC 800 (800-726786) SAMSUNG http://www.samsung.com/cz DENMARK 8 - SAMSUNG (7267864) http://www.samsung.com/dk EIRE 0818 717 100 http://www.samsung.com/ie FINLAND 30 - 6227 515 http://www.samsung.com/fi FRANCE 01 4863 0000 http://www.samsung.com/fr GERMANY 01805 SAMSUNG http://www.samsung.de (7267864, € 0,14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.
Appendix CIS http://www.samsung.com/ ua_ru UZBEKISTAN 8-10-800-500-55-500 http://www.samsung.com/ kz_ru Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.com/au CHINA 400-810-5858 http://www.samsung.com/cn 010-6475 1880 HONG KONG 3698 - 4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 3030 8282 http://www.samsung.com/in 1-800-3000-8282 1800 110011 INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.
Appendix Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle.
Appendix Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only accessories should not be mixed with other commercial wastes for disposal. Correct disposal of batteries in this product - Europe only (Applicable in the European Union and other European countries with separate battery return systems.
