SyncMaster 740NPlus / 940NPlus Install driver Install programs
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug. z This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause electric shock or fire inside the monitor.
Put down the monitor carefully. z Failing to do so may damage the monitor. Do not place the monitor face down. z This may damage the TFT-LCD surface.The installation of the bracket must be done by a qualified professional. Installing a wall bracket must be done by a qualified professional. z z Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. z Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.
the monitor could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center . z The monitor may malfunction, causing electric shock or fire. Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. z Failure to do so may cause electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. z This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center. When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.
z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product. z Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality. When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Without stand Monitor With stand Monitor & Simple stand Bottom MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Monitor & Pivot stand Monitor & Sliding Stand Monitor & Lowest HAS Stand Manual Quick Setup Guide Warranty Card (Not available in all locations) D-sub Cable Power Cord Cable User's Guide, Monitor Driver, Natural Color software, MagicTune™ software MagicRotation software
Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™ [ ] MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Custom, Text, Internet, Game, Sport and Movie, Dynamic Contrast. Each mode has its own pre-configured brightness value. You can easily select one of seven settings by simply pressing MagicBright™ control button.
] Enter button [ ] Activates a highlighted menu item. AUTO button Use this button for auto adjustment. Power button [ ]/ Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once Power indicator as the monitor saves your adjustments. See PowerSaver described in the manual for further information regarding power saving functions.
Connecting the Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use appropriate connection for your computer. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [ RGB IN ] Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-sub connection cable.
Monitor and Bottom Pivot Stand / Sliding Stand A.Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
Simple stand Pivot stand Sliding Stand Lowest HAS Stand A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4.
4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. (Microsoft® Windows® XP Operating System) This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/. 5. Monitor driver installation is completed.
3. Click "Personalization" and then "Display Settings". 4. Click "Advanced Settings…". 5. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message “Windows needs…” is displayed, as shown in the figure below, click "Continue". This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence.
Microsoft® Windows® XP Operating System 1. Insert CD into the CD-ROM driver. 2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2.
If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button. Microsoft® Windows® Millennium Operating System 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver".
One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI).
1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4. [AUTO]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
Menu Locked Description After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu MagicBright™ Description Push the MagicBright button to circle through available preconfigured modes.
Menu Description Brightness When OSD is not on the screen, push the button to adjust brightness.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the [ ] button to adjust brightness. Contrast Color You can use the on-screen menus to change the contrast according to personal preference. (Not available in MagicColor mode of Full and Intelligent.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. 3) Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
Menu Description Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only) Fine Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only) Sharpness Changes the clearance of image. (Not available in MagicColor mode of Full and Intelligent.
Menu Description You can choose one of 9 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Position You can change the vertical position where the OSD menu appears on your monitor. Transparency Change the transparency of the background of the OSD.
Menu Description Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values. Information Menu Information Description Shows a video source, display mode on the OSD screen.
Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the Installation Shield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use. 6. Choose a folder to install the MagicTune™ program. 7. Click "Install." 8. The "Installation Status" window appears. 9. Click "Finish." 10.
The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows® Control Panel. Perform the following steps remove MagicTune™ . 1. 2. 3. 4. 5. 6. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows® XP, go to [Control Panel] in the [Start] menu. Click the "Add or Remove Programs" icon in Control Panel. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™ ." Click on it to highlight it.
Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicRotation installation file. 3. Select installation Language, Click "Next". 4. When the InstallShield Wizard window appears, click "Next." 5. Select "I accept the terms of the license agreement" to accept the terms of use. 6. Choose a folder to install the MagicRotation program. 7. Click "Install." 8. The "Setup Status" window appears. 9. Click "Finish.
z z z z z Windows Windows Windows Windows Windows NT 4.0 2000 XP Home Edition XP Professional Vista™ Hardware z z 128MB Memory above(recommended) 25MB Free Hard disk space above Service Packs z z It is recommended that your System has the latest Service Pack installed. For Windows® NT 4.0, it is recommended to install Internet Explorer 5.0 and above with Active Desktop component. * For more information, visit the MagicRotation website. * Windows® is registered trademark of Microsoft Corporation,Inc.
Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see "Check Signal Cable" on the screen? Check the signal cable connection.
disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the ' ' button.
Check when MagicTune™ does not function properly. MagicTune™ feature is found only on PC (VGA) with Window OS that supports Plug and Play. * To check whether your PC is available for MagicTune™ feature, follow the steps below (When Windows is XP); Control Panel -> Performance and Maintenance -> System -> Hardware -> Device Manager -> Monitors -> After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. MagicTune™ is an additional software for the monitor.
manual for details.) How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control Panel→Display→Settings. * Contact the video card manufacturer for details. How can I set the Power Saving function? Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual).
The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips z A monitor recreates visual signals received from the computer.
SyncMaster 740NPlus General General Model Name SyncMaster 740NPlus LCD Panel Size 17 " Diagonal (43 cm) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg / 10.4 lbs Dimensions (WxHxD)/ Weight (Sliding Stand) 366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg / 10.4 lbs Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 366.0 X 351.4 X 200.0 mm / 14.4 X 13.8 X 7.9 inch (with Basic Stand) / 4.8 kg / 10.6 lbs VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.
functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.
Rate.
SyncMaster 940NPlus General General Model Name SyncMaster 940NPlus LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.55kg / 12.2 lbs Dimensions (WxHxD)/ Weight (Sliding Stand) 407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.7 kg / 12.6 lbs Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 407.6 X 368.2 X 200.0 mm / 16.0 X 14.5 X 7.9 inch (with Basic Stand) / 5.8 kg / 12.8 lbs VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.
functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.
Rate.
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
BELGIUM 02 201 2418 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(7267864) (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.
PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.A.E 800SAMSUNG (7267864) 8000-4726 http://www.samsung.
1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. { { Resolution: 1280 x 1024 Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product.
416, Mae tan-3dong, Yeongtong - gu, Suwon City, Gyeonggi-do Korea
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate a correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
