SSC21WEB-cover 2004.8.
SSC21WEB-1 2004.8.25 5:38 PM Page 2 IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Read these instructions. Keep these Instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
SSC21WEB-1 2004.8.25 5:38 PM Page 3 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SSC21WEB-1 2004.8.25 5:38 PM Page 4 IMPORTANT SAFEGUARDS Caution Power source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fire or electric shock. Do not remove the cover by yourself. (Control switches are at the front of the monitor.) 1. Read Instructions : All the safety and operating instructions should be read before the appliance is operated. 2.
SSC21WEB-1 2004.8.25 5:38 PM Page 5 8. Accessories : Do not place this monitor on an unstable cart, stand, tripod, bracket or table. The monitor may fall causing serious injury to a child or adult and serious damage to the appliance. Use only with a cart, stand, tripod. bracket or table recommended by Samsung or sold with the monitor. Any mounting of the monitor should follow Samsung’s instructions and should use a mounting accessory recommended by Samsung. 9.
SSC21WEB-1 2004.8.25 5:38 PM Page 6 13. Lightning : For added protection for this monitor during a lightning storm or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the monitor due to lightning and power-line surges. 14. Overloading : Do not overload wall outlets and extension cords as this can result in a risk of fire of electric shock. 15.
SSC21WEB-1 2004.8.25 5:38 PM Page 7 18. Replacement Parts : When replacement parts are required be sure the service technician has used replacement parts specified by Samsung or have the same characteristics as the original parts. Unauthorized substitutions may result in fire electric shock or other hazards. 19. Safety Check : Upon completion of any service or repairs to this monitor ask the service technician to preform safety checks to determine that the monitor is in proper operating condition.
SSC21WEB-1 2004.8.25 5:38 PM Page 8 Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
SSC21WEB-1 2004.8.25 5:38 PM Page 9 The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD. America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA IC Compliance Notice This Class (A) digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
SSC21WEB-1 2004.8.25 5:38 PM Page 10 Contents IMPORTANT SAFETY INSTRUCTIONS ...........................Eng-2 IMPORTANT SAFEGUARDS ..............................................Eng-4 FCC & ICES Information .......................................................Eng-7 Chapter 1: System Components and Installation 1-1) Environmental requirements for installation and safety ...Eng-12 1-2) System Components......................................................
SSC21WEB-1 2004.8.25 5:38 PM Page 11 Chapter 3: Setting each item function at SETUP MENU 3-1) ADJUST MENU function and setting method .............Eng-25 3-2) DATE/TIME MENU Function setting..........................Eng-26 3-3) DWELL TIME MENU function setting .......................Eng-26 3-4) DISPLAY MENU function setting ..............................Eng-27 3-5) TITLE MENU Function setting ....................................Eng-28 3-6) ALARM MENU Function setting.................................
SSC21WEB-1 2004.8.25 5:38 PM Page 12 Chapter 1: System Components and Installation 1-1) Environmental requirements for installation and safety This section describes the environmental requirements for safe installation and use. Install the product on a flat table or in a rack. It should be used only when level and should not be used when stood vertically or obliquely.
SSC21WEB-1 2004.8.25 5:38 PM Page 13 1-2) System Components The system consists of the following: STANDARD CAMERA MONITOR CAMERA BRACKET POWER CODE & INSTALLATION MANUAL VCR CABLE CAMERA CABLE SENSOR CONNECTOR NOTE ITEM MODEL DESCRIPTION Q’ty MONITOR SSC21WEB 21" FLAT CRT MONITOR 1 STANDARD CAMERA SOD14C NORMAL TYPE CAMERA 4 CAMERA BRACKET SBR-110 STAND TYPE BRACKET 4 Tapping Screw 3 CAMERA CABLE MCB-60 6PIN SHIELD CABLE 4 60ft(1ft=0.
SSC21WEB-1 2004.8.25 5:38 PM Page 14 1-3) CAMERA composition and installation method 1) Standard Camera composition (SOD14C) PIN NUMBER SPEC ! SPEAKER(HOT) @ VIDEO_OUT # GND $ SPEAKER(COLD) % AUDIO_OUT/ALARM_OUT ^ 12V DC a. Lens It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area. b. Microphone Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor. c.
SSC21WEB-1 2004.8.25 5:38 PM Page 15 f. Speaker It outputs the sound signal which was transfered from the monitor. 2) INSTALLING STANDARD CAMERA (SOD14C) SOD14C s camera can be attached to the wall, ceiling or shelf using the camera mount bracket (SBR-110). Choose an installation site that can sufficiently support the weight of the equipments to be installed. Attach the camera mount bracket to the wall or ceiling using the supplied three screws (M4 X L15).
SSC21WEB-1 2004.8.25 5:38 PM Page 16 3) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA(SOD14C) (1) Overview CAMERA MOUNT BRACKET (SBR-110) is used to attach the camera to a wall, ceiling or shelf. (2) Installation Explains the installation of CAMERA MOUNT BRACKET as wall as the installation of the camera onto the CAMERA MOUNT BRACKET. • Choose an installation site that can sufficiently support the weight of the equipments to be installed.
SSC21WEB-1 2004.8.25 5:38 PM • Page 17 Loosen the handle by turning it in a counter clockwise direction and then adjust the camera position . Tighten the handle, turning it clockwise, and lock the camera in position. • Connect the camera cable to the camera. Handle (3) Specifications Use : Indoor Installation : Wall or Ceiling Dimensions : 57 (W) X 47.2(H) X 100.
SSC21WEB-1 2004.8.25 5:38 PM Page 18 1-4) CAMERA Composition and Connecting Method to MONITOR After positioning monitor and installing four cameras to a desired location, please connect CAMERA to MONITOR through CAMERA CABLE (MCB-60) as shown in the below figure. Please check whether or not it is properly connected. Connection status checking method : • Turn on the monitor after connecting cameras, and check if camera image is displayed. The initial screen mode of monitor is quad mode.
SSC21WEB-1 2004.8.25 5:38 PM Page 19 1-5) External terminal connecting method for CAMERA and MONITOR 1) External terminal connecting method for CAMERA • An additional PIR sensor or external sensor can also be connected. • The additional PIR sensor can be connected as shown in the above graphic. • Sensor’s trigger signal is NO (Normal Open). • Sensor is not supplied.
SSC21WEB-1 2004.8.25 5:38 PM Page 20 f) Not Used g) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR. h) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR. i) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR. j) Connect the G (ground) terminal on the rear panel to the Ground terminal of the VCR.
SSC21WEB-1 2004.8.25 5:38 PM Page 21 Chapter 2: MONITOR FRONT PANEL KEY Function and Using Method Front Panel 2-1) TALK KEY TALK KEY allows users to transmit voice signal to intended camera by inputting voice with built-in √ MIC in the front of the monitor. For this function, select a target camera with the œENTER√ SWITCH on the FRONT PANEL, and press AUD/SP SEL KEY. At this time, if a voice signal is generated through the MIC with the TALK KEY pressed, the signal will be transmitted to the camera.
SSC21WEB-1 2004.8.25 5:38 PM Page 22 2-4) POWER SAVE- KEY Allows users to set POWER SAVE MODE of monitor. PICTURE screen is off when the POWER SAVE KEY is pressed, and the ON/OFF status of the monitor can be judged through LED ON/OFF status. Users can exit from POWER SAVE MODE by pressing POWER SAVE BUTTON again under picture “OFF” status. POWER SAVE MODE is automatically cancelled and picture is “ON” when an event such as an alarm or loss at POWER SAVE MODE occurs.
SSC21WEB-1 2004.8.25 5:38 PM Page 23 2-8) PIP- KEY Can be used to see the main screen while Single screen is displayed. The main screen can be changed and transfered to another channel while PIP is working. Please refer to "CHAPTER 4. DISPLAY MODE SETTING" for PIP function and details. 2-9) FREEZE- KEY This key allows users to see a target camera picture at PAUSE MODE.
SSC21WEB-1 2004.8.25 5:38 PM Page 24 2-13) ENTER- KEY √ key, it allows users to 1. enter SET UP MENU movement and As a multi functional œENTER√ SETTING MODE and set data, and 2. display single camera picture. Please refer to the below picture. • œENTER√ √ SWITCH using method at MENU setting Used to change data value after moving to target menu and entering setting mode by turning switch left or right. • Used to enter target setting mode by pressing switch.
SSC21WEB-1 2004.8.25 5:38 PM Page 25 Chapter 3: Setting each item function at SETUP MENU Pressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see the following menu OSD box. Setting method of each SETUP MENU function and operation is as follows. 06/01/03 SETUP 13:14:00 MENU 1. ADJUST 2. DATE/TIME 3. DWELL TIME 4. DISPLAY 5. TITLE 6. ALARM 7. NETWORK SETUP 8.
SSC21WEB-1 2004.8.25 5:38 PM Page 26 3-2) DATE/TIME MENU Function setting • Function: Sets the display date format and current time. • √ SWITCH at setup menu, Setting method: Move to #2. DATE/TIME MENU by using œENTER√ then press the ENTER SWITCH to display the OSD as shown in the below figure. (The figure shows the initial setting status.
SSC21WEB-1 2004.8.25 5:38 PM Page 27 √ SWITCH, each camera picture will be If the time is set for each camera channel by using œENTER√ displayed for the set time and switched to the next picture automatically. 3-4) DISPLAY MENU function setting • Function: Allows users to select the color and ON/OFF of borderline at QUAD DISPLAY. • √ SWITCH at Setting method: Move to #4. DISPLAY SETTING MENU by using œENTER√ SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure below.
SSC21WEB-1 2004.8.25 5:38 PM Page 28 3-5) TITLE MENU Function setting • Function: Set the title of each camera at your discretion. • √ SWITCH at SETUP MENU, Setting method: Move to #5. TITLE MENU by using œENTER√ and press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status.) 06/01/03 TITLE CAMERA1 CAMERA2 CAMERA3 CAMERA4 CAMERA5 CAMERA6 CAMERA7 CAMERA8 13:14:00 SETTING CAM1 CAM2 CAM3 CAM4 CAM5 CAM6 CAM7 BCAM8 0 1 2 3 4 5 6 7 8 9 : = .
SSC21WEB-1 2004.8.25 5:38 PM Page 29 3-6) ALARM MENU Function setting • Function: Allows users to set the ALARM MODE for each camera. • √ SWITCH at SETUP Setting method: Move to #6. ALARM MENU by using œENTER√ MENU, and press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status.
SSC21WEB-1 2004.8.25 5:38 PM Page 30 3-7) NETWORK SETTING function and setting method • Function: Allows users to select the STATIC (fixed) IP, DHCP, PPPoE of Setting. • √ SWITCH at Setting method: Move to #7, NETWORK SETUP MENU by using œENTER√ SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status) 06/01/03 13:14:00 NETWORK SETTING 1. NETWORK ACCESS 2. HTTP PORT STATIC.../DHCP.../PPPoE...
SSC21WEB-1 2004.8.25 5:38 PM Page 31 5) After setting, move to the main screen by using the MENU BOTTOM. 6) Set values will be stored shown below. It takes 2 or 3 seconds. 06/01/03 13:14:00 [S] 06/01/01 13:14:00 NETWORK SETTING CAM1 On completion of setting to Static IP(Fixed IP)setup, the screen, [S] is displayed. If the network connection is cancelled or cut, [S] starts blinking. Open your Internet Explorer web browser.
SSC21WEB-2 2004.8.25 6:30 PM Page 32 DHCP User - Constituted by Dynamic IP on the cable/xDSL modem network You can use the SSC21WEB products through the network using Dynamic IP on cable/xDSL modem. In this case, it should be connected with DDNS to support the Dynamic IP. In case a user (EX : cable modem user) does not need ID and password of the communications that he subscribes for when he logs on to he internet, he may provide the configuration using DHCP.
SSC21WEB-2 2004.8.25 6:30 PM Page 33 √ at NETWORK ACCESS, then press ENTER 2) Move to ‘DHCP...’ by using œENTER√ SWITCH to set to DHCP. 06/01/03 13:14:00 DHCP ACCESS DNS 1 DNS 2 168.126.63.001 168.126.63.002 3) DNS 1 and DNS 2 will be automatically set to DNS as shown below. √ switch to change it. Use œENTER√ 4) After setting, move to the main screen by using the MENU BOTTOM. 5) Set values will be stored as shown below. It takes 2 or 4 seconds.
SSC21WEB-2 2004.8.25 6:30 PM Page 34 8) Open your Internet Explorer web browser, type in the following in the URL window and press Enter. http://sff0000.websamsung.net Where ff0000 is the MAC address of your SSC21WEB in this example. If your SSC21WEB’s MAC address is ff0001, then type in ff0001 instead of ff0000 * Note : MAC Address. Locate the MAC Address of the SSC21WEB (each SSC21WEB has its own unique MAC address) It can be checked in ‘7.NETWORK SETUP” of SETUP MENU’.
SSC21WEB-2 2004.8.25 6:30 PM Page 35 ADSL User (PPPoE) - Constituted by IP on PPPoE (ADSL) SSC21WEB products can be used on the network using IP through PPPoE (ADSL). In case of a user (EX : ADSL user) who needs ID and password of the communications that he subscribes for in case of internet connection, the configurations using PPPoE would be available. In case of a configuration using PPPoE, SSC21WEB connection is made through the domain names (EX : http://sff0000.websamsung.
SSC21WEB-2 2004.8.25 6:30 PM Page 36 06/01/03 13:14:00 PPPoE... ACCESS DNS 1 DNS 2 USER ID USER PWD 168.126.63.001 168.126.63.002 ******** ******** 4) When the PPPoE (ADSL) type in the User Name and Password (and Confirm Password) given to you by the ADSL Service Provider. CAUTION In case of using ADSL (ISP-internet service provider, you must type correct User Name and Password by ISP to connect to SSC21WEB.
SSC21WEB-2 2004.8.25 6:30 PM Page 37 10) You can view the video source of the SSC21WEB from a remote location PC. 11) Make sure the remote PC meets the minimum specification requirements described in chapters 1 and 2, and make sure that the PC is internet capable and set up to able to browse the internet. 12) Open your Internet Explorer web browser, type in the following in the URL window and press ENTER. http://sff0000.websamsung.
SSC21WEB-2 2004.8.25 6:30 PM Page 38 CAUTION The connection to SSC21WEB is unavailable for about 2~5 minutes after ADSL Modem’s power ON. Since the connection would not be available, as IP is not received from ADSL communications, please reboot by turning off the power of ADSL Modem and SSC21WEB for more than 5 seconds and then try to connect again. 3-8) SSC21WEB basic setting 1) Open your Internet Explorer web browser, type in the following in the URL window and press ENTER.
SSC21WEB-2 2004.8.25 6:30 PM Page 39 6) When you enter properly, a window appears as shown below.
SSC21WEB-2 2004.8.25 6:30 PM Page 40 3-8-1) “LIVE” MENU - CAMERA SELECT Initial display mode of monitor if QUAD A.
SSC21WEB-2 2004.8.25 6:30 PM Page 41 PLAY STOP LIVE MODE change ADMIN MODE change - SINGLE SCREEN DISPLAY In case users want to see the camera image at full mode, Select a target camera by turning camera select key. After that it’ selected camera image will be displayed at full screen.
SSC21WEB-2 2004.8.25 6:30 PM Page 42 - Auto SEQUENCY DISPLAY MODE Pressing on the SEQUENCE KEY on the front allow to automatically switch to SINGLE MODE Full screen or QUAD MODE. If the DWELL TIME SETTING of SETUP MENU is set to 3 seconds and the SEUQENCY KEY is pressed at this time, the operation will be carried out as follows.
SSC21WEB-2 2004.8.25 6:30 PM Page 43 1. Recording When you make a recording from the Viewer, the file is automatically saved onto a directory preset by the Viewer by default. This directory is usually “C:\Program Files\Samsung \SSC21WEB\00-30-6F-FF-00” 00-30-6F-FF-00 is the MAC ADDRESS of the product. (user can change this in the SAVE KEY .Record Folder setting), where “Server Name” is the name of your SSC21WEB you have given during setup of the SSC21WEB.
SSC21WEB-2 2004.8.25 6:31 PM Page 44 2. PLAY When you select on a play key and press the Open button or double click the file, that file will play back on the Remote Viewer as a motion clip. When the file has finished playing or when you press the Stop button, the Remote Viewer will go back to Live screen. You can select several files simultaneously at once (up to 10) and the files will be played back in the order of the file name (by date and time).
SSC21WEB-2 2004.8.25 6:31 PM Page 45 3. PLAYER - Player installation/execution/deletion - Installation Player will be installed together when it is connected to SSC21WEB. - Execution (Follow the instruction to execute it separately.) Click Start Program —> SSC WEB Control —> Player. (Fig. 3-!) 1 2 FIG.3 - Deletion Click Start —> Program —> SSC WEB Control —> Uninstall. (Fig.
SSC21WEB-2 2004.8.25 6:31 PM Page 46 - Program screen configuration - How to play 1. Play - back File - Open... Selecting this, you can choose one between fjp and jpg on a window as shown below.
SSC21WEB-2 2004.8.25 6:31 PM Page 47 Having chosen and opened a file, you will see a picture as shown below. Reverse playback Enlarge Playback Reduce Pause Original size Stop Partial storing(AVI support) To the back frame Save the present frame as a JPEG image To the front frame Print Speed control Status Display the playback speed, bar magnification, and information on the storage.
SSC21WEB-2 2004.8.25 6:31 PM Page 48 Additional function (Tool) - Partial recording - Snap shot - Print - Partial Recording Partial recording is to separate a section from the file selected and played and save it as a form of AVI. Select in the toolbar and a window will appear as shown below. Start time and End time of the file will be displayed and the user can decide the section. You need to type in the correct time to execute the partial recording function.
SSC21WEB-2 2004.8.25 6:31 PM Page 49 And press ‘Save’. Then press ‘Record’ button and the picture below shows that it was completed. * Note : “AVI file frame speed setting” Frame control function of Dialogue box is to control the number of frames of AVI files. Although the original file has been recorded at a speed of 10 frames per second, 30 frames or 3-second frames of the original file will be stored and become a “second in an AVI file if you set the number of AVI file frames to 30 frames.
SSC21WEB-2 2004.8.25 6:31 PM Page 50 - Snap shot It is a function to save the present image as a form of a jpeg file. Select in the toolbar. The result will be as follows. Type in the file name and press ‘Save’ to store it as a jpeg file. - Print It is a function to print the present image. Select be as follows. Eng-50 in the toolbar.
SSC21WEB-2 2004.8.25 6:31 PM Page 51 Type in the phrase you added in ‘Description’. Then press the ‘OK’ button. Select Print and press ‘OK’.
SSC21WEB-2 2004.8.25 6:31 PM Page 52 Admin Menu It is an administrator’s menu to set the general items on SSC21WEB Server. To use this menu, you need the administrator’s ID and Password. On delivery, they are “root” (administrator’s ID) / “root” (administrator’s Password). The password can be changed on Admin Menu. Admin Menu Entering 1) Click the Admin menu and a login window will appear. 2) When you connect to the SSC21WEB Server through Web browser, the initial screen will be as follows.
SSC21WEB-2 2004.8.25 6:31 PM Page 53 3) Type in the administrator and password in the user’s name and password columns and press Enter key to execute the Admin Menu as shown below. 4) Screen configuration ! : General menus of Admin Menu. The menus related to SSC21WEB Server are divided into System, Network, Monitor Setup, and Utilities in the main. Each of them has several sub menus.
SSC21WEB-2 2004.8.25 • 6:31 PM Page 54 Admin Menu Structure Category System Configuration Main Menu System Information Admin.
SSC21WEB-2 2004.8.25 6:31 PM Page 55 3-8-2) System Configuration Menu. 1. System Information In this menu, you can check the information on the system including the name of the SSC21WEB Server, its model name and the version of the model and change the name of the SSC21WEB Server. - Menu Configuration Server Name Type in the name of the SSC21WEB Server. * Server’s name should be composed of 19 or less numerals or English alphabets.
SSC21WEB-2 2004.8.25 6:32 PM Page 56 2. Admin Password In this menu, the password of the administrator (root) can be changed. - Menu Configuration Administrator’s ID Old Password Administrator’s ID is always “root”. The initial password is “root”. New Password Type the password you want to change into. * The password should be composed of 4-8 digit numerals or alphabets. Confirm Password Type again the password you want to change into. After completing setting, click Apply button.
SSC21WEB-2 2004.8.25 6:32 PM Page 57 3. Access Configuration This menu is to set the targets the SSC21WEB Server can have an access to. - Menu Configuration Access Limitation Configuration This is to limit the maximum frame speed when the users, who are registered in the system, join and see the images. The users, who join in the system after this setting, will be connected at the limited speed. The access speed can be limited on the Local Network depending on the forwarding state of the network.
SSC21WEB-2 2004.8.25 6:32 PM Page 58 4. User Registration This is a user control menu to register, change, or delete the users who can use the SSC21WEB Server.
SSC21WEB-2 2004.8.25 6:32 PM Page 59 - Menu Configuration User ID Password Decide the ID of the person you want to register. Decide the password of the person you want to register. Confirm Type again the password of the person you want to register. Password Full Name Type in the name of the person you want to register. Add This is a menu to register a user. It is to fix the user’s ID, Password, name, and the authority of the user how far he/she can use the system.
SSC21WEB-3 2004.8.25 6:41 PM Page 60 5. Video Configuration This is to set the data to be added in the video data and set an environment for each channel. - Menu Configuration Image Size This is to choose the size of the image of video data. You can choose between 2 kinds of size (Small / large). Image Quality This is to choose the quality of the image. You can choose between 3 levels (High, Normal, Low). After completing setting, click Apply button.
SSC21WEB-3 2004.8.25 6:41 PM Page 61 6. Alarm Notification This notifies the registered users of an alarm arising situation through e-mails. At this time, maximum 5 M-JPEG pictures, which were stored, can be sent together. - Menu Configuration Service SMTP server address Authentication Login User ID Password Sender (E-mail) E-mail address 1 ~4 Image count Choose if you want to send the ALARM notifying E-MAIL. SMTP server of the ISP that provides SSC21WEB with services. ISP’s confirmation required.
SSC21WEB-3 2004.8.25 6:41 PM Page 62 EX) When user who has an e-mail address (SSC21WEB@yahoo.com) and password(123456) in YAHOO sets “Alarm Notification” in order to send a mail to test1@yahoo.com... After completing setting, click Apply button. If you click the back button, initial values are typed in all fields. The image transfer is not supported in all SMTP servers. Check the J-PEG image transfer in your mail account. In the event of Alarm, please use PLAYER to catch normal JPEG images.
SSC21WEB-3 2004.8.25 6:41 PM Page 63 3-8-3) Network Configuration Menu. 1. Network Configuration On this menu, you can fix the general environment related to the network of the SSC21WEB Server and check the present status of it. - Menu Configuration Network Configuration PPPoE(ADSL) Set “Static IP” or “DHCP”. Set PPPoE (ADSL). Network Ports Set “Network Port”. View Network Status Modification of HTTP and other application network port numbers. Network Status Notify View of network status.
SSC21WEB-3 2004.8.25 6:42 PM Page 64 1-1. Network Configuration : Static IP / DHCP Client 1) If the of the SSC21WEB Server is Static : Choose “Static IP”. 2) Type in the IP Address you want to assign to the SSC21WEB Server, NetMask, GateWay, DNS1, and DNS2 addresses. 1-2. Network Configuration : Static IP / DHCP Client 1) If the IP of the SSC21WEB Server is DHCP : Choose “DHCP Client”. 2) Type in the addresses of DNS 1 and DNS 2.
SSC21WEB-3 2004.8.25 6:42 PM Page 65 3) Click Apply button to apply the settings. If you click Reset button, the latest setting will be applied again. Click Back button if you don’t want to apply the setting. 4) Open your Internet Explorer web browser, type in the following in the URL window and press ENTER. http://sff0000.websamsung.net Where ff0000 is the MAC address of your SSC21WEB in this example. If your SSC21WEB’s MAC address is ff0001, then type in ff0001 instead of f0000.
SSC21WEB-3 2004.8.25 6:42 PM Page 66 2. PPPoE (ADSL) for Eth0 1) Service : Decide if you want to try PPPoE Connection or not. 2) User ID : User’s ID that is registered in th ISP. 3) User Password : User’s password that is registered in the ISP. 4) Confirm Password : Confirm the password. 5) DNS (Domain Name Service) : Service to convert a Domain Name (ex. www.yahoo.com) into an IP address (ex. 216.109.127.28).
SSC21WEB-3 2004.8.25 6:43 PM Page 67 3. Network Ports Configuration It sets the HTTP Port number to use when the SSC21WEB Server communicates with a Client PC. The present SSC21WEB Server uses HTTP Port (80). - HTTP Port 1) This is the port the Client PC uses to connect to the web page of the SSC21WEB Server. Depending on the environment of the network, its value can be varied. 2) The fault values is 80 and it can be assigned up to 65535 maximum.
SSC21WEB-3 2004.8.25 6:43 PM Page 68 4. View Network Status This is a menu to see the general status of the network setting of the SSC21WEB Server. - Menu Configuration Common Status LAN Status It is to check the status of the Gateway, DNS 1, and DNS 2. It is to check the status of the STATIC IP Address, Netmask, and MAC Address. PPPoE Status If the PPPoE service is in the connection status, “Link is up”. At this time, the service IP and NETMASK can be also checked.
SSC21WEB-3 2004.8.25 6:44 PM Page 69 1) DHCP Client has been set in “Network Configuration” menu and an IP has been assigned from the actual DHCP Server to make communication possible. 2) PPP Client has been set in “PPPoE” menu and communication has become possible through the connection with ISP or PPP Server. - Menu Configuration Mail Notification E-mail forwarding or not. Enable : Forward E-mails. Disable : Doesn’t forward E-mails.
SSC21WEB-3 2004.8.25 6:44 PM Page 70 Choose to use the Mail Notification function or not. Choose “Enable” if you want to notify the network status of the SSC21WEB Server to the people who want through e-mails. Type the address of the SMTP Server. * SMTP Server plays a part as a relay that receives the mail of the user and delivers it to the receiver. Set “Authentication Login” to Enable and type in the ID and password assigned from the SMTP server.
SSC21WEB-3 2004.8.25 6:44 PM Page 71 6. DDNS CONFIGURATION - Menu Configuration Server DDNS Server Select Enable or Disable Websamsung.net Note The domain name of this system is sff0000.websamsung.net CAUTION In case of a configuration using DHCP, as the connection to SSC21WEB is made using domain names (EX : http://sff0000.websamsung.
SSC21WEB-3 2004.8.25 6:44 PM Page 72 3-8-4) Monitor Set up - Menu Configuration Please refer to the CHAPTER3 of the user’s manual. Date & Time View Event Log Set the display data format and current time. Display the time and data of camera event and type of event Dwell Time Displays each picture for pre-set time and automatically Switches it to the next picture at SEQUENTIAL DISPLAY MODE.
SSC21WEB-3 2004.8.25 6:45 PM Page 73 3-8-5) Utilities This menu is for the flash memory’s update, rebooting, restoring to the basics, and system upgrade. - Menu Configuration Save Configuration Save Configuration is required to save all of new configuration in the system. Otherwise, no new configuration will be saved effective.
SSC21WEB-3 2004.8.25 6:45 PM Page 74 1. Save Configuration This menu is to save all of the present setting in the Flash Memory. If you changed any of the setting for the SSC21WEB, it is recommended that you save it in the Flash Memory in this menu.
SSC21WEB-3 2004.8.25 6:45 PM Page 75 2. Reboot This menu is for the rebooting of the system. It is better to reboot the system if you change the setting and update the flash. 1. Click “Reboot” in the utilities group. 2. Click “Reboot!!!”.
SSC21WEB-3 2004.8.25 6:46 PM Page 76 4. System Update This menu is to update the inner programs and data of the SSC21WEB Server. They are recorded in the Flash Memory and composed of 4 parts called Kernel Image, Ram disk Image, System Image, and Web Image respectively. Each image file should be stored in the user’s PC for update. Depending on the range you want to update, press the start button properly. Normal (System and Web) Update Update only the System Web.
SSC21WEB-3 2004.8.25 6:46 PM Page 77 4-2. All (kernel, RAM disk, System, Web) Update When you click the start button located in the right side of “All (Kernel, RAM disk, System, Web) Update”, a window will appear to ask if you want to update. Click “Cancel” to stop updating. 1. “OK” to proceed updating. 2. A pop-up window will appear. Choose “Zimage” in the browse.
SSC21WEB-3 2004.8.25 6:46 PM Page 78 3. Click “Next” button to move to the next stage. Click “Skip” button to move to the next stage without Kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file.
SSC21WEB-3 2004.8.25 6:47 PM Page 79 Click “Previous button to go back to the previous stage. Click the next button to execute update of the program and move to the next stage. Click the cancel button to stop the update process. 4. In the next stage, a pop-up window will appear for the file searching for the RAM Disk Update. Choose “rfs.gz” in the browse.
SSC21WEB-3 2004.8.25 6:47 PM Page 80 5. Click “Next” button to move to the next stage. Click “Skip” button to move to the next stage without Kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file. Click “Previous” button to go back to the previous stage. Click the next button to execute update of the program and move to the next stage. Click the cancel button to stop the update process.
SSC21WEB-3 2004.8.25 6:47 PM Page 81 6. In the next stage, a pop-up window will appear for the file searching process for the System Image Update. Choose “Fw_2pq.tar.gz” in the browse. 7. Click “Next” button to move to the next stage.
SSC21WEB-3 2004.8.25 6:47 PM Page 82 Click “Skip” button to move to the next stage without kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file. Click “Previous” button to go back to the previous stage. Click the next button to execute update of the program and move to the next stage. Click the cancel button to stop the update process. 8. In the next stage, a pop-up window will appear for the file searching process for the System Image Update.
SSC21WEB-3 2004.8.25 6:48 PM Page 83 9. Click “Next” button to move to the next stage. Click “Skip button to move to the next stage without Kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file. Click “Previous” button to go back to the previous stage. Click the next button to execute update of the program and move to the next stage. Click the cancel button to stop the update process.
SSC21WEB-3 2004.8.25 6:48 PM Page 84 10. A window will appear for rebooting after completing all the update processes. Click the reboot button and press the confirmation button to reboot the system. 11. Close your web browser and wait for about a minute before you log in again Files relate to the update of SSC21WEB Kernel Image RAM Disk Image zimage rfs.gz System Image Fw_2pq.tar.gz Web page Image web.tar.
SSC21WEB-3 2004.8.25 6:48 PM Page 85 3-9) VIEW EVENT LOG MENU function and setting method • Function: Displays the time and date of camera event and type of event. • √ Setting method:Move to #7. VIEW EVENT LOG MENU by using œENTER√ SWITCH at SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status.) 06/01/03 Sequence of event happening Camera No. that event happened.
2004.8.25 6:48 PM Page 86 Chapter 4: DISPLAY MODE setting method 4-1) SINGLE SCREEN DISPLAY Initial display mode of monitor is QUAD A. In case users want to see the camera image at √ SWITCH left and right. After that, full mode, select a target camera by turning œENTER√ press the ENTER SWITCH and selected camera image will be displayed at full screen. If √ SWITCH left / right at SINGLE DISPLAY MODE at this time, users turn the œENTER√ they can see another camera image at full screen.
SSC21WEB-3 2004.8.25 6:48 PM Page 87 4-2) QUAD MODE DISPLAY Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUAD DISPLAY MODE, or QUAD A (QUAD B) to QUAD B (QUAD A), or PIP MODE to QUAD MODE, press the QUAD/PAGE KEY.
2004.8.25 6:48 PM Page 88 4-3) AUTO SEQUENTIAL DISPLAY MODE Pressing on the SEQUENCE KEY on the front allows screen to automatically switch to SINGLE MODE full screen or QUAD MODE. (‘no-signal’ channels will be skipped while single screen is auto-switching.) If the DWELL TIME SETTING of SETUP MENU is set to 3 seconds and the SEQUENCE KEY is pressed at this time, the operation will be carried out as follows.
SSC21WEB-3 2004.8.25 6:48 PM Page 89 4-4) PIP MODE DISPLAY Can be used to see PIP screen in Single screen mode. √ on PIP screen ,the main screen will change. If you press the If you press the œENTER√ œENTER√ √ to the left and right,the main screen can be transferred to another channel. Sub-screen location can be selected on DISPLAY MENU in SETUP MENU.
2004.8.25 6:48 PM Page 90 4-5) ZOOM MODE DISPLAY When users want to see zoomed image of a specific area of the display, press the ZOOM KEY in the front to display zoom selection area. Select zoom target area by turning œENTER√ √ SWITCH left and right, and press the ENTER SWITCH, then, the selected area will be displayed at full single mode with zoomed area doubled. At zoom function operation at SINGLE DISPLAY MODE (CH2), the operation will be carried out as shown in figure below.
SSC21WEB-3 2004.8.25 6:48 PM Page 91 Chapter 5: Each product feature SOD14C : Standard Camera Model Name SOD14C Broadcasting System NTSC STANDARD Imaging Device 1/4 ”SUPER HAD IT CCD Effective Pixels S 510(H) x 492(V) Synchronization Internal Resolution H :330 TV Lines, V: 350 TV Lines Signal Output VBS 1.0Vp-p(75ohms composite) S/N Ratio ≤ 48 dB Minimum Scene Illumination 2lux(F2.0, 50 IRE) Gamma Correction 0.45 Lens Focal Length (f) : 3.8mm, Aperture Ratio (F) : 2.
SSC21WEB-3 2004.8.25 6:48 PM Page 92 OBSERVATION MONITOR (SSC21WEB) Video Input • CAMERA 8 Input: 1.0Vp-p(CVBS), 75Ω (vertical) • VCR 1 Input (to Video Out of VCR) : 1.0Vp-p, 75Ω (vertical) Video Output • BNC 4 Output: 1.0 Vp-p, 75Ω (vertical), S-Jack Type, CVBS • VCR 1 Output: 1.
SSC21WEB-3 2004.8.
SSC21WEB-3 2004.8.25 6:48 PM Page 94 The system performance may decrease if the computer has lower specification than the recommecdations, is not installed with the latest service pack, or has an illegally installed operation system(OS). A unique MAC address is registered to this device. If the administrator setting and monitoring may not be available due to conflicting unregistered MAC addresses, please contact a local service center or head office.
SSC21WEB-3 2004.8.25 6:48 PM Page 95 Appendix A) Software up data The initial screen of Samsung Electronics’ web site is as follows. 1. http://www.securitysamsung.com http://www.samsung.com/Products/CCTV.htm 2. Network Security in Homepage 3. Download the following items from SSC21WEB.
SSC21WEB-3 2004.8.25 6:48 PM Page 96 Appendix B) IP Router Setup Guide List of Routers compatible with SSC21WEB. Refer to Router User’s Manual for the detailed router setup. 1. Total System Configuration 2. Local System Configuration 3. Step-by-Step Examples : Linksys (Model : WRT54G) Netgear (Model : WGR614v4) D-Link (Model : DI-624+) SMC (Model : 7004VBR) CAUTION Other routers may be incompatible with SSC21WEB.
SSC21WEB-3 2004.8.
SSC21WEB-3 2004.8.25 6:48 PM Page 98 Local System Configuration 1. Connect LAN cable of Cable/ADSL modem or Direct Fixed/Static IP LAN Line to WAN port of IP Router. 2. Connect LAN ports of IP Router(1~4 or 1~8) to Ethernet port SSC21WEB to be set up and to Ethernet port of Local PC to use during setup. 3. Connect Video cable of Camera to SSC21WEB. 4. Turn on the SSC21WEB power.
SSC21WEB-3 2004.8.25 6:48 PM Page 99 Step-by-Step Setup Example of IP Router Linksys model WRT54G 1. Click the “Application and Gaming” tab. 2. Click “Port Range Forward”. 3. Port forwarding Row #1 : ! Application : Set this to “HTTP” @ Start and End : Set both to “From 10000 to 65535” # Protocol : Select “TCP” $ IP Address : SETUP MENU -> 7. NETWORK SETUP -> Check IP from network status to apply it identically to Private IP after DHCP setup.
SSC21WEB-3 2004.8.26 10:1 AM Page 100 Step-by-Step Setup Example of IP Router Netgear model WGR614v4 SSC21WEB 10000 10000 192.168.0.101 1. Click the “Router Status” 2. Click the WAN and LAN Port information. Write down the WAN Port IP Subnet Mask number and the LAN Port IP Address number. You will need it later when setting up the SSC21WEB. 3. Click “Advanced” and “Port Forwarding” 4.
SSC21WEB-3 2004.8.25 6:48 PM Page 101 Step-by-Step Setup Example of IP Router D-Link model DI-624+ 1. Select “Virtual Server” and “Advanced” You need to create Virtual Servers (Port Forwarding) for HTTP, TCP and Upgrade separately. 2. Virtual Server (Port Forwarding) for HTTP ! Enabled : Leave this “checked” @ Name : Set this to “HTTP” # Private IP : SETUP MENU -> 7. NETWORK SETUP -> Check IP from network status to apply it identically to Private IP after DHCP setup.
SSC21WEB-3 2004.8.25 6:48 PM Page 102 Step-by-Step Setup Example of IP Router SMC model 7004VBR 1. Select “NAT” and “Virtual Server” You need to create Virtual Servers (Port Forwarding) for HTTP 2. Virtual Server (Port Forwarding) for HTTP : use the first empty ID row. ! IP Address : SETUP MENU -> 7. NETWORK SETUP -> Check IP from network status to apply it identically to Private IP after DHCP setup. (Eng-32 Setup) * That is not in use by any other device connected to the Router including the Local PC.
SSC21WEB-cover 2004.8.25 6:23 PM Page 1 Samsung CCTV dba GVI 2801 Trade Center Drive. Suite 120 Carrollton, TX 75007 Toll Free : 888-595-2288 Part No.
