SyncMaster 275T Install driver
Notation Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause electric shock or fire.
Failure to do so may cause electric shock or fire inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or the person carrying it. Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or the person carrying it. Do not place the product on an unstable or small surface area.
Do not place the monitor face down. This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause a malfunction or fire. Others Do not remove the cover (or back).
This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small metal objects on the monitor. This may a malfunction, an electric shock or fire.
Viewing the monitor continuously at a too close angle may result in damage to your eyesight. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.
the monitor directly in front of you. z Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level. z Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. z Keep your arms level with the back of your hands. z Keep the angle of the elbow perpendicular. z Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Package Contents Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Quick Setup Guide (Not available in all locations) User's Guide, Monitor Driver Cable Power Cord D-sub Cable Sold separately S-Video Cable RCA Cable Component Cable DVI-D Cable Speaker package(option) Speaker Your Monitor Front USB Cable
MENU button [ Adjust buttons [ Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. ] ] Analog/Digital(PC) : MagicBright™ button [ ] These buttons allow you to adjust items in the menu. MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Custom, Text, Internet, Game, Sports, Movie and Dynamic CR. Each mode has its own pre-configured brightness value.
This will save power and reduce eye fatigue. 4) Custom Select this mode when you want to adjust the image according to your preferences. >> Click here to see an animation clip Brightness button [ ] Enter button [ ]/ SOURCE button When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off.
POWER : Connect the power cord for your monitor to the POWER on the back of the monitor. DVI(HDCP) / RGB DVI(HDCP) : Connect the DVI cable to the DVI(HDCP) port on the back of your monitor. RGB : Connect the RGB terminal at the back of your monitor to your computer.
z The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. Stand Stopper z Remove the fixing pin on the stand to lift the monitor up and down. See Connecting Cables for further information regarding cable connections.
Connecting Cables Connect the power cord for your monitor to the POWER port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use appropriate connection for your computer. Using the RGB (Analog) connector on the video card. - Connect the signal cable to the 15-pin, RGB port on the back of your monitor. [ RGB ] Using the DVI (Digital) connector on the video card. - Connect the DVI cable to the DVI(HDCP) port on the back of your monitor.
Power Consumption Connect the To use 2.5W (Max., each port) 2.5W (Max., each port) 2.5W (Max., each port) UP port of the monitor and the USB port of the computer with the USB cable. DOWN port, you have to connect the UP (Upstream Cable) to the PC. Make sure to use the USB cable supplied with this monitor to connect the monitor's UP port and your computer's USB port. Connect the DOWN port of the USB monitor and a USB device with the USB cable.
When connecting a speaker, be careful that the grooves of the monitor and the speaker . ( )are aligned with each other. Adjust the aligned positions until you hear a ‘click’. If a speaker is connected correctly, you can hear a ‘click’.If a speaker is connected without you hearing a ‘click’, the holding part may become damaged. If you need to separate, please pull ( ) a little and push to the right.
This monitor allows the user to connect it to such input devices as a DVD player, a VCR or a camcorder without disconnecting the PC. The configuration at the back of the monitor may vary from product to product. Connecting AV Devices The monitor has AV connection terminals to connect AV input devices like DVD, VCR or Camcorder. You may enjoy AV signals as long as the monitor is turned on.
Connecting DVD/DTV Set Top Box Connect to the DVD/DTVSet Top Box input if the device has a DVD/DTV connector. You can watch Component simply by hooking up the Component with the monitor as long as the power is on. Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the PR, PB, Y input ports using a component video cable (PR, PB, Y). Then, start the DVD with a DVD disc inserted. Select Component using the SOURCE button.
Using ( ),You can swivel the monitor left and right at an angle of 90° to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide. When you try to rotate the monitor in the state of the power cord or cable connecting to the monitor, the power cord of cable can be destroyed. Tilt angle Using ( ), You can adjust the tilt anlgle within a range of 3° forward to 25° backward for the most comfortable viewing angle.
Monitor Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Monitor driver installation is completed. Installing the Monitor Driver (Manual) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux Microsoft® Windows Vista™ Operating System Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel".
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click "Update Driver…" in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System Insert the CD into the CD-ROM drive. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced.
Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver." and select "Install from a list or." then click "Next" button. Select "Don't search ,I will." then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
If you can see following "Message" window, then click the "Continue Anyway" button. Then click the "OK" button. This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click the "Close" button then click the "OK" button continually. Monitor driver installation is completed.
How to install Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Choose "Monitor." Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click "Update Driver." then click the "Next" button.
Control Buttons Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu. Analog/Digital(PC) : MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes.
When OSD is not on the screen, push the button to adjust brightness. Press this button to activate a highlighted menu item. Selects the input signal while the OSD is off. Press to self-adjust to the incoming Analog signal. The values of fine,coarse and position are adjusted automatically. AUTO PIP Push the PIP button to turn PIP On/Off. Direct Functions AUTO Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.
In case of pushing MENU button after locking OSD Menu Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the menu button for more than five (5) seconds to activate the OSD adjustment lock function. Locked Unlock : Hold down the menu button for more than five (5) seconds to deactivate the OSD adjustment lock function.
Menu MagicBright™ /Mode Description Analog/Digital(PC) : MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes. (Custom → Text → Internet → Game → Sports → Movie → Dynamic CR ) Digital(DVD)/AV/S-Video/Component : Mode The Monitor has four automatic picture settings that are preset at the factory.
Menu Description Brightness When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu SOURCE Description Selects the input signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- Analog, Digital, AV, S-Video and Component input signal.) Changing the source is only allowed for external devices that are connected to the monitor at the time.
Menu PIP Description Push the PIP button to turn PIP screen On/Off. You can view a picture from AV, S-Video, or Component through the PIP screen in Analog and Digital (PC) mode. OSD Function Input The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution.
Menu Description Play/Stop Use to select PC or other external input sources connected to the Monitor. Use to select the screen of your choice. Source List 1) Analog 2) Digital 3) AV 4) S-Video 5) Component MENU → → → , → Name the input device connected to the input jacks to make your input source selection easier.
using the OSD menu. 2) Text : For documentations or works involving heavy text. 3) Internet : For working with a mixture of images such as texts and graphics. 4) Game : For watching motion pictures such as a game. MagicBright™ 5) Sports : For watching motion pictures such as a Sports. 6) Movie : For watching motion pictures such as a DVD or Video CD. 7) Dynamic CR : Dynamic CR is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast.
2) 4:3 MENU → , → → , → → , → When the PIP is on, you can adjust the PIP screen setting. PIP Picture 1) Contrast : Adjusts the Contrast of the PIP window on the screen. 2) Brightness : Adjusts the Brightness of the PIP window on the screen. 3) Sharpness : Adjusts the Sharpness of the PIP window on the screen 4) Color : Adjusts the Color of the PIP window on the screen 5) Tint : Adds a natural tone to the PIP window.
This will save power and reduce eye fatigue. 4) Custom : Select this mode when you want to adjust the image according to your preferences MENU → , → → → , → You can use the on-screen menus to change the contrast and brightness according to personal preference. 1) Contrast : Adjust the Contrast. Contrast Brightness 2) Brightness : Adjust the Brightness. Custom Sharpness 3) Sharpness : Adjust the Sharpness. 4) Color : Adjust the picture Color. Color 5) Tint : Adds a natural tone to the display.
Menu Description Play/Stop Implements the natural color chroma according to the display screen. Automatically adjusts to the display screen. Can improve the skin tones. MagicColor 1) Off 2) Intelligent Enhance natural color except skin tone. 3) Full Displays both natural skin tones and enhanced colors. 4) Demo Displays the improved image on the left and the original on the right.
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Turn the PIP Screen on or off. You can view a picture from AV, S-Video, or Component through the PIP screen in Alalog and Digital mode. PIP 1) Off 2) On MENU → Source → , → , → → , → → , → , → → , → → , → Change the Position of the PIP window. / / / MENU → Setup → Change the Size of the PIP window.
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Play/Stop You can choose one of 11 languages. Language MENU → , → → → , → Changes the opaqueness of the background of the OSD.
Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the ' ' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". monitor driver? Driver Installation Instructions. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. Install the monitor driver according to the Driver Installation Instructions. Check the following items if there is trouble with the monitor. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting.
scratch the case. Do not allow any water to go inside the monitor. Self-Test Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check Turn off both your computer and the monitor. Unplug the video cable from the back of the computer. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below.
Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1920 x 1200 60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble.
Specifications General Model Name SyncMaster 275T LCD Panel Size 27" Wide Diagonal (68 cm) Display area 581.76 mm (H) x 363.6 mm (V) Pixel Pitch 0.303 mm (H) x 0.303 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Resolution Optimum resolution 1920x1200@60Hz Maximum resolution 1920x1200@60Hz Input Signal, Terminated RGB Analog, DVI-D, AV, S-Video, Component,USB(1U/4D) 0.7 Vp-p ± 5% TTL level (V high ≥ 2.0V, V low ≤ 0.
15pin 3-row D-sub connector, 24pin 3-row DVI-D connector, Composite, S-Video, Component Dimensions (W x H x D) / Weight 629.0 X 410.5 X 81.0 mm / 24.8 x 16.2 x 3.2 inch (Without Stand) 629.0 X 486.0 X 280.0 mm / 24.8 x 19.1 x 11.0 inch (With Stand) / 10.4 Kg / 22.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit : kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate.
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
BELGIUM 03 201 2418 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(7267864) (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.
INDIA 3030 8282, 1800 1100 11 http://www.samsung.com/in INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.com/jp MALAYSIA 1800-88-9999 http://www.samsung.com/my PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg THAILAND 1800-29-3232, 03-689-3232 http://www.samsung.com/th TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen. Example : If the resolution is 1920 x 1200 , this means the screen is composed of 1920 horizontal dots (horizontal resolution) and 1200 vertical lines (vertical resolution). S-Video Short for "Super Video.
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
