SyncMaster 591S/793S/793DF/795DF/797DF/997DF/793MB/795MB
INDEX Main Page Safety Instructions Notational Power nstallation Troubleshooting Check List Q&A Self-Test Feature Check Cleaning Other Specifications General Specifications Introduction Unpacking Preset Timing Modes PowerSaver Front Rear Bottom Information Service Terms Natural Color Authority Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Base Installation
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. z If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Do not use a damaged or loose plug. z This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands.
Installation Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Put your monitor in a location with low humidity and a minimum of dust. z An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or human body. Place the monitor on a flat and stable surface. z The monitor can cause injury by falling. Set down the monitor carefully. z It could be damaged or broken.
Cleaning When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using. Do not spray detergent directly on the monitor.
Other Do not remove cover(or back). No user serviceable parts inside. z z This may cause an electric shock or a fire. Refer servicing to qualified service personnel. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. z This may cause an electric shock or a fire. Do not place any heavy objects on the monitor. z This may cause an electric shock or a fire.
Other Keep the monitor away from any magnetic substances. z This may cause discoloring or distortion of the image.
Unpacking Monitor and Stand Power Cord Stand Quick Setup Guide (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
Front 1. Menu button 2. Adjust buttons 3. Enter button 4. Power button 5. Power indicator Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the menu. Used to select the OSD menu. Use this button to turn the monitor on and off. This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
Rear SyncMaster 591S/793S/793DF/795DF /797DF/997DF/793MB/795MB General (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal Cable Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. BNC Connectors (Option) SyncMaster 997DF (The configuration at the back of the monitor may vary from product to product.) 1.
Bottom 1. Signal Cable 2. Power port 3. Tilt/Swivel Base Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Connect the power cord for your monitor to the power port on the back of the monitor. You can separate the base from the monitor.
Connecting Your Monitor General SyncMaster 591S/793S/793DF/795DF /797DF/997DF/793MB/795MB 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included).
Connecting Your Monitor pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter. 4. When you use a BNC connector. Connect the signal cable to the BNC signal port on the back of your monitor/computer. 5. Turn on your computer and monitor. If your monitor displays an image, installation is complete. Opstilling-For multimedia-model 1. Sluk for computeren og fjern strømkablet. 2. Tilslut signalkablet til din computers videoport (videoboard, videokort eller grafikkort).
Connecting Your Monitor Fodstykke for Multimedia højttaler 1. Mic by-pass jack For transmission af din stemme, tilslut et lydkabel fra mic by-pass jack til mic in jack på lydkortets slot i din computer. 2. Stereo input jack Tilslut et lydkabel fra input kilden (lydkort, computer, CD-ROM drev). 3. DC strømkabel Tilsluttes til monitorens DC 12V output jack. 4. Strømindikator Lyser grøn, når der er tændt for højttalerne. 5. On/Off lydstyrke Tænder/slukker og justerer lydstyrken 6.
Installing the Monitor Driver Automatic Manual When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.com/ (WorldWide) http://www.samsungusa.
Installing the Monitor Driver Automatic Manual When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.com/ (WorldWide) http://www.samsungusa.
Installing the Monitor Driver 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
Installing the Monitor Driver This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window.
Installing the Monitor Driver How to install 1. 2. 3. 4. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced..". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver..
Base Installation With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle. Note: The base is detachable. Attaching the Base 1. 2. 3. 4. Place the monitor upside-down on a flat work surface. Align the tabs on the base with the corresponding slots on the bottom of the monitor. Press the base onto the monitor until the tabs are fully engaged in the slots. Push the base toward the front of the monitor until the release latch clicks into the locked position.
Check List Note Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Symptom Check List Solutions No images on the screen. I cannot turn on the monitor. Is the power cord connected properly? Check the power cord connection and supply. Can you see " Check the signal cable connection.
Check List Symptom Check List Solutions The image on the screen is shaking. Check the monitor configuration to see if it is in Interlace Mode. (Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc) The signal from the video card exceeds the maximum resolution and frequency of the monitor. Are there any magnetic products such as a power adapter, speaker or a high voltage wire near by? Move the monitor away from anything that can create a strong magnetic field.
Check List Symptom Check List Solutions The screen is out of focus or OSD cannot be adjusted. Have you adjusted the resolution or frequency on the monitor? Adjust the resolution and frequency of the video card. (Refer to the Preset Display Modes). The screen is partially distorted. Are there any magnetic products such as an adapter, speaker or a high voltage wire near the monitor? Enter the OSD and perform a "Degauss".
Q&A Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows XP/2000: Set the resolution at the Control Panel, Display, Settings . * Contact the video card manufacturer for details.
Self-Test Feature Check SyncMaster 591S/793S/793DF/795DF/797DF/793MB/795MB Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If your monitor works normally, the following screen appears. SyncMaster 591S/793DF/795DF SyncMaster 997DF Failure of any of the boxes to appear indicates a problem with your monitor.
Self-Test Feature Check l A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Sync. Out of Range, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. l Judging the monitor's working condition If there is no image on the screen or an "Sync.
General Model Name General PowerSaver Preset Timing Modes SyncMaster 797DF Picture Tube Type 17"(43cm) DynaFlat (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 1024 x 768 68.677 84.997 94.
General Model Name General PowerSaver Preset Timing Modes SyncMaster 795DF/795MB Picture Tube Type 17"(43cm) DynaFlat (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 1024 x 768 68.677 84.997 94.
General Model Name General PowerSaver Preset Timing Modes SyncMaster 793S Picture Tube Type 17"(43cm) Full square type (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.23mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 53.674 85.061 56.
General Model Name General PowerSaver Preset Timing Modes SyncMaster 793DF/793MB Picture Tube Type 17"(43cm) DynaFlat (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 53.674 85.061 56.
General Model Name General PowerSaver Preset Timing Modes SyncMaster 591S Picture Tube Type 15" (38cm) Full square type (35cm viewable) Deflection angle 90 ° Dot Pitch 0.24mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static/Glare.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 85.008 36.000 -/- VESA, 640 x 480 43.269 75.000 31.
General Model Name General PowerSaver Preset Timing Modes SyncMaster 997DF Picture Tube Type 19"(48cm) DynaFlat (45.8cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static/Glare.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 1024 x 768 68.677 84.997 94.
Service AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 1300 362 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc.
Service UKRAINE : SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE 4 Glybochitska str. Kiev, Ukraine Tel. 8-044-4906878 Fax 8-044-4906887 Toll-free 8-800-502-0000 http://www.samsung.com.ua/ United Kingdom : Samsung Electronics (UK) Ltd. Samsung House, 225 Hook Rise South Surbiton, Surrey KT6 7LD Tel. : (0208) 391 0168 Fax. : (0208) 397 9949 < European Service Center & National Service > Stafford Park 12 Telford, Shropshire, TF3 3BJ Tel. : (0870) 242 0303 Fax. : (01952) 292 033 http://samsungservice.co.
Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
Natural Color Natural Color Software Program One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI).
Authority Information in this document is subject to change without notice. © 2004 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
