user manual

ManualsBrandsSamsung ManualsComputer MonitorComputer Monitor DE46C

User Manual

DE40C

DE46C

DE55C

The color and the appearance may differ depending on

the product, and the specifications are subject to

change without prior notice to improve the performance.

BN46-00299A-02

Summary of content (243 pages)

PAGE 1
User Manual DE40C DE46C DE55C The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
PAGE 2
Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS 12 Copyright 13 Cleaning 13 Storage 14 Safety Precautions 14 15 16 18 Symbols Electricity and Safety Installation Operation 23 Checking the Contents 23 25 Removing the Packaging (for DE40C and DE46C models only) Removing the Packaging (for DE55C models only) Checking the Components 28 Parts 28 30 31 32 35 Control Panel Reverse Side Anti-theft Lock Remote Control Connection Using an IR Stereo Cable 36 Before Installing the Product
PAGE 3
Table Of Contents CONNECTING AND USING A SOURCE DEVICE USING MDC 56 Before Connecting 56 Pre-connection Checkpoints 57 Connecting and Using a PC 57 60 Connecting to a PC Changing the Resolution 62 Connecting an External Monitor 63 Connecting to a Video Device 63 63 64 64 65 65 Connection Using the AV Cable Connection Using the Component Cable Connection Using an HDMI-DVI Cable Connection Using an HDMI Cable Connecting to an Audio System Connecting to an Antenna 66 Connecting the network bo
PAGE 4
Table Of Contents SCREEN ADJUSTMENT 73 What is MDC? 73 75 76 77 78 79 81 82 84 87 88 97 100 105 Connecting to MDC Connection Management Auto Set ID Cloning Command Retry Getting Started with MDC Main Screen Layout Menus Screen Adjustment Sound Adjustment System Setup Tool Settings Other Functions Troubleshooting Guide 107 Picture Mode 107 108 If the input source is PC, DVI or DisplayPort If the input source is AV, Component, HDMI or TV 108 Backlight / Contrast / Brightness / Sharpness / Color / T
PAGE 5
Table Of Contents SOUND ADJUSTMENT CHANNEL 113 Advanced Settings 114 114 114 114 114 114 114 115 115 115 Dynamic Contrast Black Tone Flesh Tone RGB Only Mode Color Space White Balance 10p White Balance (Off / On) Gamma Expert Pattern Motion Lighting (Off / On) 116 Picture Options 117 117 117 117 118 118 118 118 Color Tone Color Temp.
PAGE 6
Table Of Contents NETWORK SYSTEM 126 Network Setting 126 127 130 131 133 Connecting to a Wired Network Wired Network Settings Connecting to a Wireless Network Wireless Network Setting WPS(PBC) 134 Network Status 135 MagicInfo Lite Settings 136 Wi-Fi Direct 136 Soft AP 137 AllShare Settings 137 Using the AllShare Play Function 138 Device Name 139 Setup 140 Multi Control 140 Configuring settings for Multi Control 141 Time 141 142 142 143 143 Clock Sleep Timer On Timer Off Timer H
PAGE 7
Table Of Contents 146 Caption 146 146 147 Caption Caption Mode Digital Caption Options 148 Security 148 148 149 151 Safety Lock (Off / On) Button Lock (Off / On) Program Rating Lock (Off / On) Change PIN 151 PIP 152 Auto Protection Time 153 Screen Burn Protection 153 154 154 155 Pixel Shift Timer Immediate Display Side Gray 155 Ticker 156 Video Wall 156 156 157 157 157 Video Wall Format Horizontal Vertical Screen Position 158 Source AutoSwitch Settings Table Of Contents 7
PAGE 8
Table Of Contents SUPPORT 159 General 159 159 160 160 160 160 160 161 161 161 161 Max.
PAGE 9
Table Of Contents ALLSHARE PLAY MAGICINFO LITE 173 What is AllShare Play? 173 175 176 177 Read the following before using AllShare Play with a USB device Using a USB device Connecting to a PC over a network Using the DLNA features 178 Using the Basic AllShare Play Features 178 179 179 180 Sorting the file lists Playing Selected Files Copying Files Creating a Playlist (Playlist) 181 My List 181 My List options 182 Videos 182 Playing a Video 183 Photos 183 Viewing a Photo (or Slide Show)
PAGE 10
Table Of Contents TROUBLESHOOTING GUIDE 195 MagicInfo Lite Player 195 200 201 202 Network Schedule Local Schedule Internal AutoPlay USB AutoPlay 203 Local Schedule Manager 203 207 209 210 211 212 214 Registering a Local Schedule Modifying a Local Schedule Deleting a Local Schedule Running a Local Schedule Stopping a Local Schedule Viewing the details of a Local Schedule Copying a Local Schedule (Local Schedule) 216 Content Manager 216 217 Copying content Deleting content 218 Settings 218 218
PAGE 11
Table Of Contents SPECIFICATIONS APPENDIX 228 General 230 PowerSaver 231 Standard Signal Mode Table 233 License 234 Contact SAMSUNG WORLD WIDE 236 Responsibility for the Pay Service (Cost to Customers) 236 236 236 Not a product defect A Product damage caused by customer's fault Others 237 Optimum Picture Quality and Afterimage Burn-in Prevention 237 238 Optimum Picture Quality Prevention of Afterimage Burn-in 240 Terminology INDEX Table Of Contents 11
PAGE 12
Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality. © 2012 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics. Microsoft and Windows are registered trademarks of Microsoft Corporation.
PAGE 13
Before Using the Product Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. Take the following steps when cleaning. The following images are for reference only. Real-life situations may differ from what is shown in the images. 1. Power off the product and computer. 2. Disconnect the power cord from the product. Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result. 3.
PAGE 14
Before Using the Product Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL. This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.
PAGE 15
Before Using the Product Electricity and Safety The following images are for reference only. Real-life situations may differ from what is shown in the images. Warning Do not use a damaged power cord or plug, or a loose power socket.  An electric shock or fire may result. Do not use multiple products with a single power socket.  Overheated power sockets may cause a fire. Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
PAGE 16
Before Using the Product Caution Do not disconnect the power cord while the product is being used.  The product may become damaged by an electric shock. Only use the power cord provided with your product by Samsung. Do not use the power cord with other products.  ! A fire or electric shock may result. Keep the power socket where the power cord is connected unobstructed.  The power cord must be disconnected to cut off power to the product when an issue occurs.
PAGE 17
Before Using the Product Keep the plastic packaging out of the reach of children.  Children may suffocate. ! Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)  The product may fall and become damaged and/or cause an injury.  Using the product in an area with excess vibration may damage the product or cause a fire. Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke.
PAGE 18
Before Using the Product Caution Do not drop the product while moving.  Product failure or personal injury may result. ! Do not set down the product on its front.  The screen may become damaged. When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the product is not protruding.  The product may fall and become damaged and/or cause an injury.  Install the product only on cabinets or shelves of the right size.
PAGE 19
Before Using the Product If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer Service Center.  ! An electric shock or fire may result. Do not let children hang from the product or climb on top of it.  Children may become injured or seriously harmed. If the product is dropped or the outer case is damaged, turn off the power switch and disconnect the power cord. Then contact Samsung Customer Service Center.
PAGE 20
Before Using the Product Ensure the vents are not blocked by tablecloths or curtains.  100 An increased internal temperature may cause a fire. Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches, etc) into the product (via the vent or input/output ports, etc).  Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product. Then contact Samsung Customer Service Center.
PAGE 21
Before Using the Product Looking at the screen too close for an extended period of time can deteriorate your eyesight. ! Do not use humidifiers or stoves around the product.  A fire or electric shock may result. Rest your eyes for more than 5 minutes for every 1 hour of product use.  Eye fatigue will be relieved. ! Do not touch the screen when the product has been turned on for an extended period of time as it will become hot. Store small accessories out of the reach of children.
PAGE 22
Before Using the Product When replacing the battery, insert it with the right polarity (+, -).  Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid. ! The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.
PAGE 23
1 1.1 Preparations Checking the Contents The appearance of the actual product may differ from the images shown. 1.1.1 Removing the Packaging (for DE40C and DE46C models only) 1 Open the packaging box. Be careful not to damage the product when you open the packaging with a sharp instrument. 2 Remove the styrofoam from the product. 3 Check the product and remove the styrofoam and plastic bag. The appearance of the actual product may differ from the image shown. This image is for reference only.
PAGE 24
1 Preparations 1.1.2 Removing the Packaging (for DE55C models only) 1 Remove the black locking device at the bottom of the box. 1 2 2 Using the grooves in the box, lift and remove the top of the box. 3 Check the components and remove the styrofoam and plastic bag. 3 The appearance of actual components may differ from the image shown. This image is for reference only. 4 Store the box in a dry area so that it can be used when moving the product in the future.
PAGE 25
1.1.3 Checking the Components  Contact the vendor where you purchased the product if any components are missing.  The appearance of the components and items sold separately may differ from the image shown.  A stand is not provided with the product. To install a stand, you can purchase one separately. Components Components may differ in different locations.
PAGE 26
1 Preparations Items sold separately  The stand is not supplied.  The following items can be purchased at your nearest retailer.
PAGE 27
1 Preparations RS232C(OUT) Adapter RS232C(IN) Adapter The RS232C adapter can be used to connect to another monitor using the D-SUB (9-pin) type RS232C cable. Ensure you connect each of the adapters to the correct RS232C IN or OUT port on the product.
PAGE 28
1 1.2 Preparations Parts 1.2.1 Control Panel Panel Key POWER Remote sensor Speaker Panel Key Buttons Description Power on the product. If you press the [ ] button when the product is turned on, the control menu will be displayed. To exit the OSD menu, press and hold the panel key for at least one second. Move to the upper or lower menu. You can also adjust the value of an option. In TV mode, you can change the channel by moving the panel key up or down when the control menu is not displayed.
PAGE 29
1 Preparations Control menu If you press the [ ] button on the panel key ("1.2 Parts") when the product is turned on, the control menu will be displayed. CONTENT Return Icons Description Select the connected input source. Move the panel key right to select Source [ ] in the control menu. When the list of input sources is displayed, move the panel key up or down to select the desired input source. Next, press the panel key. Display the OSD menu.
PAGE 30
1 Preparations 1.2.2 Reverse Side The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. RS232C IN RS232C OUT IR / AMBIENT SENSOR IN AUDIO OUT RGB / DVI / HDMI / AV / COMPONENT AUDIO IN USB USB POWER DP IN HDMI IN DVI IN DP OUT ANT IN RGB IN Port IR COMPONENT IN OUT RJ45 Description [RS232C IN] Connects to MDC using an RS232C-stereo cable.
PAGE 31
1 Preparations Port Description [IR OUT] Receives the remote control signal via the external sensor board and outputs the signal via LOOPOUT. [RJ45] Connects to MDC using a LAN cable. Assembling the Holder-Wire stand 1.2.3 Anti-theft Lock  An anti-theft lock allows you to use the product securely even in public places.  The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
PAGE 32
1 Preparations 1.2.4 Remote Control  Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.  Remote control button functions may differ for different products. Power on the product. Power off the product. Enter the password in the OSD menu, or change the channel. Press to select additional channels (digital) being broadcasted by the same station.
PAGE 33
1 Preparations Adjusting the OSD with the Remote Control 1. Open the OSD menu. 2. Select from Picture, Sound, Channel, Network, System or Support in the displayed OSD menu screen. 3. Change settings as desired. 4. Finish setting. 5. Close the onscreen display (OSD) menu.
PAGE 34
Remote Control Reception Range 7m ~ 10m 1 Preparations Use the remote control within 7m to 10m from the sensor on the product at an angle of 30˚ from the left and right.  Store used batteries out of reach of children and recycle.  Do not use a new and used battery together. Replace both batteries at the same time.  Remove batteries when the remote control is not to be used for an extended period of time.
PAGE 35
1 Preparations 1.2.5 Connection Using an IR Stereo Cable Turn off the device before connecting the External Sensor Kit. After it is connected, turn on the device. Controlling more than one display product using your remote control 1 2 IR OUT IR/ AMBIENT SENSOR IN  Connect the [IR OUT] port on the product to the [IR / AMBIENT SENSOR IN] port on the other display product using the dedicated stereo cable.
PAGE 36
1 1.3 Preparations Before Installing the Product (Installation Guide) To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.  Ensure that an authorized installation company installs the wall mount.  Otherwise, it may fall and cause personal injury.  Make sure to install the specified wall mount. 1.3.1 Tilting Angle and Rotation Contact Samsung Customer Service Center for further details.
PAGE 37
1 Preparations 1.3.2 Ventilation 1. Installation on a Perpendicular Wall A Minimum 40 mm B Ambient temperature: Under 35 C  When installing the product on a perpendicular wall, allow at least 40 mm of space between the product and wall surface for ventilation and ensure that the ambient temperature is kept below 35 C. A B Figure 1.1 Side view 2. Installation on an Indented Wall Contact Samsung Customer Service Center for further details. Figure 1.
PAGE 38
1 1.4 Preparations Dimensions 5 1 2 4 3 Unit: mm (inches) Model name 1 2 3 4 5 DE40C 919.6 (36.2) 885.6 (34.9) 498.2 (19.6) 532.0 (20.9) 35.1 (1.38) DE46C 1054.5 (41.52) 1018.1 (40.1) 572.7 (22.5) 608.5 (24.0) 35.1 (1.38) DE55C 1249.5 (49.19) 1209.6 (47.6) 680.4 (26.8) 721.0 (28.4) 35.1 (1.38) All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. Refer to the dimensions prior to performing installation of your product.
PAGE 39
1 1.5 Preparations Installing the Wall Mount 1.5.1 Preparing before installing Wall-Mount To install a wall-mount from another manufacturer, use the Holder-Ring. 1 1.5.2 Installing the Wall Mount Kit The wall mount kit (sold separately) allows you to mount the product on the wall. For detailed information on installing the wall mount, see the instructions provided with the wall mount. We recommend you contact a technician for assistance when installing the wall mount bracket.
PAGE 40
1 Preparations  Standard dimensions for wall mount kits are shown in the table below.  Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.  Do not use screws that do not comply with the VESA standard screw specifications.  Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product.
PAGE 41
1 1.6 Preparations Remote Control 1.6.1 Cable Connection RS232C Cable  Interface RS232C (9 pins) Pin TxD (No. 2), RxD (No. 3), GND (No.
PAGE 42
1 Preparations  RS232C cable Connector: 9-Pin D-Sub to Stereo Cable 9 3 2 1 5 -P2- 6 1 -P1- -P1- Female -P1- -P2- -P2- Rx 2 --------> 1 Tx Tx 3 <-------- 2 Rx Gnd 5 --------- 3 Gnd STEREO PLUG (3.5ø) LAN Cable  Pin assignment 1 2 3 4 5 6 7 8 Pin No.
PAGE 43
1 Preparations  Connector: RJ45 Direct LAN cable (PC to HUB) HUB P2 RJ45 MDC P1 P1 P2 Signal P1 TX+ 1 TX- RJ45 MDC P2 Signal <--------> 1 TX+ 2 <--------> 2 TX- RX+ 3 <--------> 3 RX+ RX- 6 <--------> 6 RX- Cross LAN cable (PC to PC) RJ45 MDC P1 P2 Signal P1 P2 Signal TX+ 1 <--------> 3 RX+ TX- 2 <--------> 6 RX- RX+ 3 <--------> 1 TX+ RX- 6 <--------> 2 TX- 1 Preparations 43
PAGE 44
1 Preparations 1.6.
PAGE 45
1 Preparations  Connection 3 RJ45 RS232C OUT RS232C IN RS232C OUT IN RS232C OUT IN OUT 1 Preparations 45
PAGE 46
1 Preparations 1.6.3 Control Codes Viewing control state (Get control command) Header Command 0xAA Command type Data length ID Checksum 0 Controlling (Set control command) Header Command 0xAA Command type Data length Data 1 Value ID Checksum Command No.
PAGE 47
1 Preparations  To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID as "0xFE" and transmit commands. Commands will be executed by each device but ACK will not respond. Power control  Function A product can be powered on and off using a PC.
PAGE 48
1 Preparations Volume control  Function The volume of a product can be adjusted using a PC.
PAGE 49
1 Preparations Input source control  Function The input source of a product can be changed using a PC.
PAGE 50
1 Preparations Header Command Data length Ack/Nak r-CMD Val1 3 ‘N’ 0x14 "ERR" ID 0xAA Checksum 0xFF "ERR": A code showing what error has occurred Screen  Function The screen mode of a product can be changed using a PC. Screen mode cannot be controlled when the Video Wall function is enabled. This control can only be used on models that include a TV.
PAGE 51
1 Preparations Screen size control  Function The screen size of a product can be changed using a PC.
PAGE 52
1 Preparations PIP On/Off control  Function The PIP mode of a product can be turned on or off using a PC.   Only available on models that have the PIP function.  The mode cannot be controlled if Video Wall is set to On.  This function is not available in MagicInfo.
PAGE 53
1 Preparations Auto adjustment control (PC and BNC only)  Function Automatically adjust the PC system screen using a PC.
PAGE 54
1 Preparations Video Wall Mode Control  Function Video Wall mode can be activated on a product using a PC. This control is only available on a product whose Video Wall is enabled. This function is not available in MagicInfo.
PAGE 55
1 Preparations Safety Lock  Function PC can be used to turn the Safety Lock function on or off on a product. This control is available regardless of whether or not the power is turned on.
PAGE 56
2 2.1 Connecting and Using a Source Device Before Connecting Check the following before you connect this product with other devices. Devices that can be connected to this product include PCs, camcorders, speakers, set top boxes and DVD/Blu-ray Disc players. 2.1.1 Pre-connection Checkpoints  Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device.
PAGE 57
2 2.2 Connecting and Using a Source Device Connecting and Using a PC 2.2.1 Connecting to a PC  Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable.  A PC can be connected to the product in a variety of ways. Select a connection method suitable for your PC. Connecting parts may differ in different products.
PAGE 58
2 Connecting and Using a Source Device Connection Using an HDMI-DVI Cable HDMI IN RGB / DVI / HDMI / AV / COMPONENT AUDIO IN When you connect a PC to the product using an HDMI-DVI cable, set Edit Name to DVI PC to access video and audio content stored on the PC.
PAGE 59
2 Connecting and Using a Source Device Connection Using an DP Cable DP IN 2 Connecting and Using a Source Device 59
PAGE 60
2 Connecting and Using a Source Device 2.2.2 Changing the Resolution Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP Go to Control Panel 1 Display Settings, and change the resolution.
PAGE 61
2 Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution, and change the resolution.
PAGE 62
2 2.3 Connecting and Using a Source Device Connecting an External Monitor DP OUT DP IN The following images are for reference only. Real-life situations may differ from what is shown in the images.
PAGE 63
2 2.4 Connecting and Using a Source Device Connecting to a Video Device  Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable.  You can connect a video device to the product using a cable.  Connecting parts may differ in different products.  After connecting a source device, press the SOURCE button on the remote control and select the connected source device. 2.4.
PAGE 64
2 Connecting and Using a Source Device 2.4.3 Connection Using an HDMI-DVI Cable HDMI IN RGB / DVI / HDMI / AV COMPONENT AUDIO IN  Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device. When you connect a video device to the product using an HDMI-DVI cable, set Edit Name to DVI Device to access video and audio content stored on the video device.
PAGE 65
2 Connecting and Using a Source Device  Be sure to use an HDMI cable with a thickness of 14 mm or less.  Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection error may occur.  A basic high-speed HDMI cable or one with ethernet is recommended. This product does not support the ethernet function via HDMI. 2.4.5 Connecting to an Audio System AUDIO OUT 2.4.
PAGE 66
2 2.5 Connecting and Using a Source Device Connecting the network box (Sold separately) 2.5.1 MagicInfo To use MagicInfo, a network box (sold separately) must be connected to the product. For details on how to connect to a network box, refer to the user's manual provided with the network box upon purchase.  To change the MagicInfo settings, run "MagicinfoSetupWizard" on the desktop.  For details on how to use MagicInfo, refer to the DVD provided with the network box.
PAGE 67
2 Connecting and Using a Source Device 3 Select the default application you want to run when MagicInfo starts. MagicInfo Setup Wizard - v.1.12 Select Application - step 1 MagicInfo Pro (LAN, WAN based version) MagicInfo-i Premium (Web-based version) Select Later < Back(B) 4 Next(N) > Finish Cancel Enter the IP information. MagicInfo Setup Wizard - v.1.12 Select TCP/IP - step 2 Obtain an IP address automatically Use the following IP address: IP address: 192 . 168 . 0 .
PAGE 68
2 Connecting and Using a Source Device 5 Select a language. (The default language is English.) MagicInfo Setup Wizard - v.1.12 Select Language -step 3 Select the language you want to install on the system for menus and dialogs. Current Language : Engilsh Chinese [Traditional] German English French Italian Japanese Korean Russian Swedish Turkish Chinese [Simplified] Portuguese < Back(B) 6 Next(N) > Finish Cancel Select a display mode. MagicInfo Setup Wizard - v.1.
PAGE 69
2 Connecting and Using a Source Device 7 Double-check the settings you have just configured. MagicInfo Setup Wizard - v.1.12 Setup Information 1. Application : MagicInfo Pro [LAN,WAN based version\ 2. Internet Protocol [TCP/IP] IP : 192.168.0.102 3. Language : 4. Screen Type : English Landscape Do not show again < Back(B) Apply Finish Cancel If the execution icon does not appear, double-click the MagicInfo icon on the desktop. The icon will appear at the bottom right of the screen.
PAGE 70
2 2.6 Connecting and Using a Source Device Changing the Input source 2.6.1 Source MENU [m] Support Contents Home ENTER [ Source ] Source allows you to select a variety of sources and change source device names. Source You can display the screen of a source device connected to the product. Select a source from Source List to display the screen of the selected source.
PAGE 71
3 Using MDC MDC (Multiple Display Control) is an application that allows you to easily control multiple display devices simultaneously using a PC. 3.1 Configuring Settings for Multi Control MENU [m] System Multi Control ENTER [ ] Assign an individual ID to your product. 3.1.1 Configuring settings for Multi Control  ID Setup Assign an ID to a set. (Range: 0~99) Press  or to select a number, and press [ ].
PAGE 72
3 3.2 Using MDC MDC Program Installation/Uninstallation 3.2.1 Installation 1 2 Insert the installation CD into the CD-ROM drive. Click the MDC Unified installation program. If a software installation window is not displayed on the main screen, install with the MDC Unified execution file in the MDC folder on the CD. 3 4 5 Select a language for installation. Next, click "OK". When the "Welcome to the InstallShield Wizard for MDC_Unified" screen appears, click "Next".
PAGE 73
3 3.3 Using MDC What is MDC? Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC. 3.3.1 Connecting to MDC Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
PAGE 74
3 Using MDC Using MDC via Ethernet Enter the IP for the primary display device and connect the device to the PC. One display device can connect to another using an RS-232C serial cable. Connection using a direct LAN cable RJ45 Multiple products can be connected using the [RJ45] port on the product and the LAN ports on the HUB. Connection using a cross LAN cable RS232C OUT RJ45 Multiple products can be connected using the [RS232C IN / OUT] port on the product.
PAGE 75
3 Using MDC 3.3.2 Connection Management Connection management includes the Connection list and Connection list modification options. Connection list - Connection list shows the details of the connections such as connection setting (IP/ COM, Port No, MAC, and Connection Type), connection status, Set ID Range, and detected devices. Each connection can contain a maximum of 100 devices connected in serial daisy-chain fashion.
PAGE 76
3 Using MDC 3.3.3 Auto Set ID Auto Set ID feature assigns a Set ID for all the LFDs connected in daisy-chain of a selected connection. There can be a maximum of 100 LFDs in a connection. The Set ID is assigned sequentially in the daisychain running from 1 to 99, and then finally to Set ID 0.
PAGE 77
3 Using MDC 3.3.4 Cloning Using the Cloning feature, you can copy the setting of one LFD and apply it to multiple selected LFDs. You can select specific tab categories or all tab categories for cloning, using the copy setting option window.
PAGE 78
3 Using MDC 3.3.5 Command Retry This feature is used to specify the maximum number of times the MDC command will be retried in case of there being no reply or a corrupted reply from an LFD. The retry count value can be set using the MDC options window. The retry count value must be between 1-10. The default value is 1.
PAGE 79
3 Using MDC 3.3.6 Getting Started with MDC 1 To start the program, click Start 2 Click Add to add a display device.  Programs Samsung MDC Unified. If the connection is established via RS232C, go to Serial and specify the COM Port.
PAGE 80
3 Using MDC  If the connection is established via Ethernet, enter the IP that was entered for the display device.
PAGE 81
3 Using MDC 3.3.7 Main Screen Layout 1 6 5 4 2 3 1 Menu Bar Change the status of a display device or the properties of the program. 2 Device Category View a list of connected display devices or device groups. 3 Schedule Category View a list of schedules for display devices. 4 Set List Select the display device you want to adjust. 5 Modify the Set List Add, edit, regroup or delete sets. 6 Help Topics Display help topics for the program.
PAGE 82
3 Using MDC 3.3.8 Menus You can power on or off a selected device or change the input source or volume of the device. Choose display devices from the list of sets, and select the Home tab. 1 Home Select an item and change the corresponding setting. Power  On: Power on a selected display.  Off: Power off a selected display. Input Input Source : Change the input source.   Input sources available can vary depending on the Display Device Models.
PAGE 83
3 Using MDC 3  Alert Fault Device  This menu shows a list of display devices which have following errors - fan error, temperature error, brightness sensor error, or lamp error. Select a display device from the list. The Repair button will be enabled. Click the refresh button to refresh the error status of the display device. The recovered display device will disappear from the Fault Device List.  Fault Device Alert  Display device in which error is detected will be reported by email.
PAGE 84
3 Using MDC 3.3.9 Screen Adjustment The screen settings (contrast, brightness, etc.) can be adjusted. Choose display devices from the list of sets, and select the Picture tab. Custom Select an item and change the corresponding screen setting.  Color and Tint are not available if the input source is PC.  Red, Green, Blue and PC Screen Adjustment are not available if the input source is Video.
PAGE 85
3 Using MDC Green  Customize the intensity of green color for the selected display device. Blue  Customize the intensity of blue color for the selected display device. Options Dynamic Contrast Adjust the Dynamic Contrast for the selected display device. Gamma Control Change the gamma value for the selected display. Auto Motion Plus This option is used to view dynamic images.  Off: Disable the Auto Motion Plus function.  Clear: Set the level of Auto Motion Plus to clear.
PAGE 86
3 Using MDC HDMI Black Level Adjust the HDMI Black Level for the selected display device. Size Picture Size Adjust the screen size for the selected display device. The Detail item will be disabled if Picture Size is set to a mode that does not support detailed configuration. The -/+ buttons can be used to adjust Zoom. The screen can be relocated using the up/down/left/right buttons. Detail You can view details of the selected screen size.
PAGE 87
3 Using MDC 3.3.10 Sound Adjustment You can change the sound settings. Choose display devices from the list of sets, and select the Sound tab. The Bass or Treble item will be disabled if the item is not supported by the selected set. Bass Adjust the bass for the selected display. Treble Adjust the treble for the selected display. Balance(L/R) Adjust the volume of the left and right speakers of the selected display device.
PAGE 88
3 Using MDC 3.3.11 System Setup Choose display devices from the list of sets, and select the System tab. Video Wall The Video Wall function can be used to display part of a whole picture or repeat the same picture on each of connected multiple display devices. Video Wall is enabled only when devices are in the group. Video Wall Enable or disable Video Wall. Format Select the format to display the split screen.
PAGE 89
3 Using MDC H Select the number of horizontal display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. V Select the number of vertical display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. Screen Position View the layout of displays (configured by the screen divider) or change the layout as required.
PAGE 90
3 Using MDC PIP Basic information required to adjust PIP will appear in the menu screen.  PIP will be disabled when Video Wall is ON.  Note that Picture Size is disabled when PIP is ON. PIP Size View the PIP Size of the current display. PIP Source Select a PIP input source. Sound Select Select and enable the sound from either the primary screen or secondary screen. Channel The channel can be changed if PIP Source is TV.
PAGE 91
3 Using MDC General User Auto Color Automatically adjust the screen colors. Available only in PC mode. Auto Power Set the product to automatically power on. Standby Control Set the standby mode to activate if an input source is not detected. Fan & Temperature Configure the settings required to detect the fan speed and internal temperature for the product's protection. Fan Control Select a method to configure the fan speed. Fan Speed Configure the fan speed.
PAGE 92
3 Using MDC Security Safety Lock Lock the on-screen menus. To unlock the menus, set Safety Lock to Off. Button Lock Lock the buttons on the display device. To unlock the buttons, set Button Lock to Off. OSD Display Source OSD Select whether to display a message when the Source is changed. Not Optimum Mode OSD Select whether to display a message when a non-compatible mode is selected. No Signal OSD Select whether to display a message when there is no input signal.
PAGE 93
3 Using MDC Time Clock Set Change the current time on the selected display device according to the time set on a PC. If the time is not set on the display device, null values will be displayed. Timer  On Time: Set the time to power on the selected display device.  Off Time: Set the time to power off the selected display device.  Volume: Specify the volume of the display device when it is powered on by On Time.
PAGE 94
3 Using MDC  Once: Activate the timer only one time.  EveryDay: Activate the timer every day.  Mon~Fri: Activate the timer from Monday through Friday.  Mon~Sat: Activate the timer from Monday through Saturday.  Sat~Sun: Activate the timer on Saturdays and Sundays.  Manual: Customize days of the week. The checkboxes to select days of the week below Repeat are enabled only if Manual is selected.
PAGE 95
3 Using MDC Screen Burn Protection Pixel Shift Move the screen slightly at specified time intervals to prevent screen burn-in. Screen Saver This function prevents screen burn-in when the screen of the selected display device is left idle for an extended period of time.  Interval: Set the interval to activate the Screen Saver.  Mode: The Time setting can vary for each Mode.
PAGE 96
3 Using MDC Safety Screen The Safety Screen function can be used to prevent screen burn-in when a stationary image displays on the screen of a display device for an extended period of time. Lamp Control Lamp Control is used to adjust the backlight to reduce power consumption. Automatically adjust the backlight of the selected display device at a specified time. If Manual Lamp Control is adjusted, Auto Lamp Control will automatically switch to Off. Manually adjust the backlight for the selected display.
PAGE 97
3 Using MDC 3.3.12 Tool Settings 1 1 2 3 4 Security Panel Control Turn on or off the screen of a display device. Remote Control Enable or disable the remote control. 2 Reset Reset Picture Reset the screen settings. Reset Sound Reset the sound settings. Reset System Reset the system settings. Reset All Reset the screen, sound and system settings at the same time. (Menu Language, Security, Time, Multi Control and Anynet+ will not be initialized.
PAGE 98
3 Using MDC 3 Edit Column Options Language: Select a language to use in the MDC program. After selecting a language, restart the MDC program to use the selected language. Command Retry Count: Specify the number of retry attempts when a command fails. Error Status Interval: Specify the time interval to query the display device in order to check if "Fault Device" has occurred. Mail Alert Interval: Specify the time interval for email notifications in the event when "Fault Device" occurs.
PAGE 99
3 Using MDC Edit Column Select the items you want to display in the list of sets. 4 Information View the program information.
PAGE 100
3 Using MDC 3.3.13 Other Functions Resizing a Window Place the mouse pointer on a corner of the program window. An arrow will appear. Move the arrow to customize the size of the program window.
PAGE 101
3 Using MDC Group Management Creating Groups Create groups and manage the list of sets on a group basis. Duplicate group names cannot be used. 1 Right-click and select Group Edit in the display device list section on the left side of the program window. 2 In the Edit Group window displayed, click Add on the same level or Add on the sub level.  Add on the same level: Create a group on the same level as the selected group.
PAGE 102
3 Using MDC  3 Add on the sub level: Create a sub-group under the selected group. Enter the group name. Deleting Groups 1 2 Select a group name, and click Edit. 3 Click Yes. The group will be deleted. In the Edit Group window displayed, click Delete. Renaming Groups 1 2 Select a group name, and click Edit. In the Edit Group window displayed, click Rename. Rename 3 If a cursor appears in the old group name, enter a new group name.
PAGE 103
3 Using MDC Schedule Management Creating Schedules Create and register a schedule on a group basis. 1 Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled in the middle. 2 Click the Add button. The Add Schedule window will appear.
PAGE 104
3 Using MDC 3 Click Add below the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list window.  Device Group: Select a group.  Date&Time   Instant Execution: Run the schedule immediately.  Timer: Set the date, time and interval to run the schedule. Action: Select a function that will activate at the specified time and interval.
PAGE 105
3 Using MDC 3.3.14 Troubleshooting Guide Issue The display you want to control does not appear on the system information chart. Solution 1. Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). 2. Check that another display with a duplicate ID is not connected. Connecting displays with a duplicate ID can cause the displays not to be shown due to data collision. 3. Check that the display ID is within the range of 0 and 99.
PAGE 106
3 Using MDC How display properties are shown when multiple displays are used 1 2 3 When no display is selected: The default value is displayed. When one display is selected: Settings for the selected display are displayed. When two displays are selected (e.g. in sequence of ID 1 and ID 3): The settings for ID 1 are displayed before the settings for ID 3. 4 When the All+Select checkbox is checked and all displays are selected: The default settings are displayed.
PAGE 107
4 Screen Adjustment Configure the Picture settings (Brightness, Color Tone, etc.). The layout of the Picture menu options may vary depending on the product. 4.1 Picture Mode MENU [m] Picture Picture Mode ENTER [ ] Select a picture mode (Picture Mode) suitable for the environment where the product will be used. Different Picture Mode options are displayed depending on the current input source.
PAGE 108
4 Screen Adjustment 4.1.2 4.2 If the input source is AV, Component, HDMI or TV  Dynamic: This mode is suitable when the ambient light is bright.  Standard: This mode is generally suitable for any environment.  Natural: Suitable for reducing eye strain.  Movie: This mode reduces eye fatigue. Backlight / Contrast / Brightness / Sharpness / Color / Tint (G/R) MENU [m] Picture ENTER [ ] Your product has several options for adjusting picture quality.
PAGE 109
4 4.3 Screen Adjustment Screen Adjustment MENU [m] Picture Screen Adjustment ENTER [ ] Screen Adjustment provides various picture size and aspect ratio options. Select an option using the and arrow keys, and the press [ press [ ]. Use the arrow keys to select an option in the sub-menu, and then ]. Different Screen Adjustment options are displayed depending on the current input source.
PAGE 110
4 Screen Adjustment Do not set your product to 4:3 format for a long time. The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn) which is not covered by the warranty.  Screen Fit: Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals are inputted.  Custom: Changes the resolution to suit the user's preferences.
PAGE 111
4 Screen Adjustment 4.3.2 Zoom/Position Adjusts the picture position. Position is only available if Picture Size is set to Zoom1, Zoom2, Wide Fit or Screen fit.  To use the Position function after selecting Zoom1, Zoom2, Wide Fit or Screen fit, follow these steps. 1 2 3 4 5 Press the button to select Position. Press the [ Press the ] button. or Press the [ button to move the picture up or down. ] button. Select Close by pressing the and buttons sequentially.
PAGE 112
4 Screen Adjustment 4.3.4 Resolution Select If the picture is not normal even when the resolution of the graphics card is one of the following, you can optimize the picture quality by selecting the same resolution for the product as the PC using this menu. Available resolutions: Off / 1024 x 768 / 1280 x 768 / 1360 x 768 / 1366 x 768 This option is available when the input source is PC. 4.
PAGE 113
4 4.5 Screen Adjustment Advanced Settings MENU [m] Picture Advanced Settings ENTER [ ] Advanced Settings Dynamic Contrast Off Black Tone Off Flesh Tone 0 RGB Only Mode Color Space Off Native White Balance 10p White Balance Off The displayed image may differ depending on the model.
PAGE 114
4 Screen Adjustment 4.5.1 Dynamic Contrast Adjust the screen contrast.  Off / Low / Medium / High 4.5.2 Black Tone Select the black level to adjust the screen depth.  Off / Dark / Darker / Darkest 4.5.3 Flesh Tone Emphasize pink Flesh Tone. 4.5.4 RGB Only Mode Displays the Red, Green and Blue color for making fine adjustments to the hue and saturation.  Off / Red / Green / Blue 4.5.5 Color Space Adjusts the range and variety of colors (the color space) available to create images.
PAGE 115
4 Screen Adjustment  Blue: Adjust the blue level.  Reset: Resets the 10p White Balance to its default settings.  Available when the Picture Mode is set to Movie and when the external input is set to all input.  Some external devices may not support this function. 4.5.8 Gamma Adjust the primary color intensity. 4.5.9 Expert Pattern Use the Expert Pattern function to calibrate the picture.
PAGE 116
4 4.6 Screen Adjustment Picture Options MENU [m] Picture Select an option using the setting, and then press [ Picture Options and ENTER [ arrow keys, and the press [ ] ]. Use the arrow keys to change the ]. Picture Options Color Tone Off Color Temp. 10000K Digital Noise Filter Off MPEG Noise Filter Off HDMI Black Level Normal Flim Mode Off Calibrated Value Don’t Apply The displayed image may differ depending on the model.
PAGE 117
4 Screen Adjustment Input source Picture Mode Picture Options HDMI Dynamic, Standard, Natural, Movie Color Tone / Color Temp. / Digital Noise Filter / MPEG Noise Filter / HDMI Black Level AV, Component, TV, HDMI (1080i) Dynamic, Standard, Natural, Movie Color Tone / Color Temp. / Digital Noise Filter / MPEG Noise Filter / Film Mode 4.6.1 Color Tone If the input source is PC, DVI, DisplayPort or HDMI (PC connection).
PAGE 118
4 Screen Adjustment 4.6.5 HDMI Black Level Selects the black level on the screen to adjust the screen depth.  Normal / Low Available only in HDMI and DVI mode (AV Timing: 480p, 576p, 720p, 1080i, 1080p). 4.6.6 Film Mode Sets the product to automatically sense and process film signals from all sources and adjust the picture for optimum quality.  Off / Auto1 / Auto2 Available in TV, AV and COMPONENT (480i / 1080i) or HDMI(1080i). 4.6.
PAGE 119
5 5.1 Sound Adjustment Configure the sound (Sound) settings for the product. Sound Mode MENU [m] Sound Sound Mode ENTER [ ] Use the up and down arrow keys to select an option, and then press [ ]. Sound Sound Mode Standard Sound Effect Broadcast Audio Options Speacker Settings Reset Sound The displayed image may differ depending on the model.  Standard: Selects the normal sound mode.  Music: Emphasizes music over voices.  Movie: Provides the best sound for movies.
PAGE 120
5 5.2 Sound Adjustment Sound Effect MENU [m]  Sound Sound Effect ENTER [ ]  If Speaker Select is set to External, Sound Effect is disabled.  Available only when Sound Mode is set to Standard. Virtual Surround (Off / On) This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head Related Transfer Function) technology.
PAGE 121
5 5.3 Sound Adjustment Broadcast Audio Options MENU [m]  Sound Broadcast Audio Options ENTER [ ] Preferred Language (digital channels only) Use the up and down arrow keys to select a language, and then press [ ]. Digital-TV broadcasts can simultaneously transmit many audio tracks (for example, simultaneous translations of the program into foreign languages). You can only select a language from among the ones being broadcasted.
PAGE 122
5 Sound Adjustment  Auto Volume (Off / Normal / Night) Normal equalizes the volume level on each channel, so that when you change channels, the volume level is the same. Night equalizes and decrease the volume level on each channel, so each channel is quieter. Night is useful at night, when you may want to keep the volume low. To use the volume control of a connected source device, set Auto Volume to Off.
PAGE 123
6 Channel MENU [m] Channel ENTER [ ] This option is available when the input source is TV. Channel Antenna Cable Auto Program Clear Scrambled Channel Fine Tune Crosstalk Noise Reduction Off The displayed image may differ depending on the model. 6.1 Antenna (Air / Cable) MENU [m] Channel Antenna ENTER [ ] Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the LED display.
PAGE 124
6 6.2 Channel Auto Program The Auto Program function memorizes all channels that are available over the air or through your cable system and adds them to the Channel List. To start Auto Program, follow these steps: 1 MENU [m] Push Channel Auto Program ENTER [ ] on your remote. The Antenna Source screen appears. 2 On the Antenna Source screen, select the source of your product signal.
PAGE 125
6 6.4 Channel Fine Tune MENU [m] Channel Fine Tune ENTER [ ] (analog channels only) If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, fine tune the channel manually. Scroll to the left or right until the image is clear. 6.5  This function is only available in Cable mode.  Settings are applied to the channel you’re currently watching.
PAGE 126
7 7.1 Network Network Setting 7.1.1 Connecting to a Wired Network There are three ways to attach your product to your LAN using cable.  You can attach your product to your LAN by connecting the LAN port on the back of your product to an external modem using a LAN cable. See the diagram below.
PAGE 127
7 Network access the Internet so you do not have to enter them manually. Most home networks are Dynamic Networks. Some networks require a Static IP address. If your network requires a Static IP address, you must enter the IP address, subnet mask, gateway, and DNS values manually on your product Cable Setup Screen when you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values, contact your Internet Service Provider (ISP).
PAGE 128
7 Network Automatic Network Settings Use the Automatic Network Settings when connecting your product to a network that supports DHCP. To set up your product cable network connection automatically, follow these steps. How to set up automatically 1 2 3 Go to the Network Settings screen. Select Start, press [ ], and then press [ ] again. The network test screen appears and verifies the network connection. When the connection has been verified, the “Internet is connected successfully.” message appears.
PAGE 129
7 Network If you make a mistake when entering a number, re-enter the number to correct it. You can also press the up or down arrow button to change the number one unit at a time. 9 10 11 12 When done entering the IP Address, press [ ]. Press the down arrow key to go to the Subnet Mask fields, and then press [ ]. Repeat the same entry process for Subnet Mask, Gateway, and DNS Server. When done, select OK at the bottom of the page, and then press [ ].
PAGE 130
7 Network 7.1.3 Connecting to a Wireless Network To connect your product to your network wireless, you need a wireless router or modem and a Samsung Wireless LAN adapter (WIS10ABGN, WIS12ABGNX) , which you connect to your product back or side panel USB port. See the illustration below.
PAGE 131
7 Network  The product may not recognize the “Samsung Wireless LAN adapter” if you connect it to the product with a USB hub or USB extension cable other than the cable supplied with the product. 7.1.4 Wireless Network Setting Automatic Network Setup Most wireless networks have an optional security system that requires devices that access the network to transmit an encrypted security code called an Access or Security Key.
PAGE 132
7 Network Manual Network Setup Use the Manual Network Settings when connecting your product to a network that requires a Static IP address or if the automatic connection process has failed. Getting the Network Connection Values To view the Network connection values on most Windows computers, follow these steps. 1 2 3 4 Right click the Network icon on the bottom right of the screen. In the pop-up menu that appears, click Status. On the dialog that appears, click the Support tab.
PAGE 133
7 Network 13 Repeat the entry process for each field in the IP Address. If you make a mistake when entering a number, re-enter the number to correct it. You can also press the 14 15 16 17 or button to change the number one unit at a time. When done entering the IP Address, press [ Press the ]. button to go to the Subnet Mask fields, and then press [ ]. Repeat the same entry process for Subnet Mask, Gateway, and DNS Server. When done, select OK at the bottom of the page, and then press [ ].
PAGE 134
7 7.2 Network Network Status MENU [m] Network ENTER [ Network Status ] You can check the current network and Internet status. Network Status Your wireless network and Internet connection are setup and ready to use. 00 : 12 : fb : df : 29 : 76 ***. ***. ***. ***. ***. ***. ***. ***. ***. ***. ***. ***. ***. ***. ***. ***. MAC Address IP Address Subnet Mask Gateway DNS Server You are connected to the Internet.
PAGE 135
7 7.3 Network MagicInfo Lite Settings MENU [m] 1 Network MagicInfo Lite Settings ENTER [ ] Server  Server (Setting the MagicInfo Lite Server IP) Enter the server IP address and port number. Use 7001 as the port number.  If unable to connect to the server using port number 7001, check with your server administrator to find the correct port number and then change the port number.  FTP Mode Select an FTP operating mode: Active or Passive.
PAGE 136
7 7.4 Network Wi-Fi Direct MENU [m] Network Wi-Fi Direct ENTER [ ] Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router. To use this function, your mobile device should be supported by the Wi-Fi Direct. To connect your mobile device with your product using Wi-Fi Direct, follow these steps: 1 2 Go to Wi-Fi Direct screen (Network Wi-Fi Direct). The product starts to search devices.
PAGE 137
7 Network Return  Returns to the screen before entering the security key. 7.6  The security key should consist of more than 8 digits.  Input the generated security key into the device you want to connect.  If network does not operate normally, check the security key again. An incorrect security key may cause a malfunction.
PAGE 138
7 7.7 Network Device Name Select or enter a device name. This name can be shown on network remote controls over the network.
PAGE 139
8 8.1 System Setup MENU [m] System Setup ENTER [ ] Configure the channels and the time when setting up the product for the first time or when resetting the unit. System Setup Multi Control Time Menu Language Rotate Menu English Landscape Eco Solution Caption On The displayed image may differ depending on the model.
PAGE 140
8 8.2 System Multi Control MENU [m] System Multi Control ENTER [ ] Assign an individual ID to your product. 8.2.1 Configuring settings for Multi Control  ID Setup Assign an ID to a set. (Range: 0~99) Press  or to select a number, and press [ ]. ID Input Enter the ID number of the product connected to the input cable for input signal reception. Enter the number you want using the number buttons on the remote control.
PAGE 141
8 8.3 System Time MENU [m] System Time ENTER [ ] You can configure Clock Set or Sleep Timer. You can also set the product to automatically turn on or off at a specified time using the Timer function. 8.3.1 Clock Set the clock to use the various various timer features of the product. Changing the Setting for Clock  Clock Mode Set the current time manually or automatically.  Auto: Have the product set the current time automatically using the time from a digital channel.
PAGE 142
8 System 8.3.2 Sleep Timer Automatically shuts off the product after a preset period of time. (Off, 30 min, 60 min, 90 min, 120 min, 150 min and 180 min). Use the up and down arrows to select a period of time, and then press [ ]. To cancel Sleep Timer, select Off. 8.3.3 On Timer Set On Timer so that your product turns on automatically at a time and on a day of your choosing.  On Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the current time first.
PAGE 143
8 System 8.3.4 Off Timer Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer 1 ~ Off Timer 7) You must set the clock before you can use Off Timer. Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the days you want Off Timer to turn off your product.  The check mark indicates days you’ve selected. Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers.
PAGE 144
8 8.4 System Menu Language MENU [m] System Menu Language ENTER [ ] Set the menu language. A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your PC. 8.5 Rotate Menu MENU [m] System Rotate Menu ENTER [ ]  Landscape: Display the menu in landscape mode (default).  Portrait: Display the menu in portrait mode on the right side of the product screen.
PAGE 145
8 8.6 System Eco Solution MENU [m] System Eco Solution ENTER [ ] Eco Solution Energy Saving Off Eco Sensor On No Signal Power Off Off Auto Power Off Off The displayed image may differ depending on the model. 8.6.1 Energy Saving Save power with the Energy Saving feature. While Energy Saving mode is active, the product power consumption will be controlled to save power.  Off / Low / Medium / High / Picture Off 8.6.
PAGE 146
8 System 8.6.4 Auto Power Off (Off / On) The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel within 4 hours to prevent overheating. 8.7 Caption MENU [m] System Caption ENTER [ ] (On-Screen Text Messages) 8.7.1 Caption You can switch the caption function on or off. If captions are not available, they will not be displayed on the screen.
PAGE 147
8 System 8.7.3 Digital Caption Options (digital channels only) Adjusts the each option. When done, select Close.  Size: Options include Default, Small, Standard and Large. The default is Standard.  Font Style: Options include Default and Styles 0 to 7. The default is Style 0.  Font Color: You can change the color of the letters. Options include Default, White, Black, Red, Green, Blue, Yellow, Magenta and Cyan. The default is White.
PAGE 148
8 8.8 System Security MENU [m] System Security ENTER [ ] Every time you access the Security functions, the PIN screen will appear and the default PIN number is “0-0-0-0". The PIN screen closes and the Security menu appears. Security Safety Lock Off Button Lock Off Program Rating Lock Off Change PIN The displayed image may differ depending on the model. 8.8.1 Safety Lock (Off / On) It sets safe lock function.
PAGE 149
8 System 8.8.3 Program Rating Lock (Off / On) When turned on, the Program Rating Lock feature can automatically block programs that you deem inappropriate for your children. You must enter a PIN (personal identification number) before you can set or change any of the Program Rating Lock restrictions.   This option is available when the input source is TV.  The default PIN number for a new product set is “0-0-0-0”. TV Rating: You can block TV programs based on their ratings.
PAGE 150
8 System  Canadian English Rating: You can block TV programs based on their Anglophone Canadian rating. Canadian English Rating displays a column with locks and the following ratings categories. C: Programming intended for children under age 8. / C8+: Programming generally considered acceptable for children 8 years and over to watch on their own. / G: General programming, suitable for all audiences. / PG: Parental Guidance.
PAGE 151
8 System 8.8.4 Change PIN The Change PIN screen will appear. Choose any 4 digits for your PIN and enter it in Enter New PIN. Reenter the same 4 digits in Confirm New PIN. When the Confirm screen disappears, press the Close button. The product has memorized your new PIN. 8.9 PIP MENU [m]  System PIP , ENTER [ ]  If you have set Double( Size. ) mode in PIP (Picture-in-Picture), you cannot adjust the Picture  For PIP sound, refer to the Sound Select instructions.
PAGE 152
8 System  Size ( ,  Position ( , , , , In Double (  , , , ): Select a size for the subpicture. ): Select a position for the sub-picture. , ) mode, you cannot select Position. Sound Select (Main / Sub): You can choose to listen to the sound from the Main picture or the Sub picture. 8.
PAGE 153
8 System 8.11 Screen Burn Protection MENU [m] System Screen Burn Protection ENTER [ ] To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology. Pixel Shift moves the picture slightly on the screen. The Pixel Shift Time setting allows you to program the time between movements of the picture in minutes.
PAGE 154
8 System 8.11.2 Timer You can set the timer for Screen Burn Protection. Timer   Off Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals (Period). Period and Time can be configured when Repeat is selected.  Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to End Time). The option is enabled only when Clock Set is configured.  Mode: Select a screen protective pattern to display.
PAGE 155
8 System 8.11.4 Side Gray When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen.  Off / Light / Dark 8.12 Ticker Input text while a video or image is displayed and display the text on the screen.  Off / On Message, Time, Position, Motion, and Font Style are enabled only when Ticker is set to On.  Message: Enter a message to display on the screen.  Time: Set the Start Time and End Time to display a message (Message).
PAGE 156
8 System 8.13 Video Wall MENU [m] System Video Wall ENTER [ ] Customize the layout of multiple displays that are connected to form a video wall. In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays. To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support the MagicInfo function.
PAGE 157
8 System 8.13.3 Horizontal This function automatically divides the screen according to the specified number of horizontal displays. Enter the number of horizontally arranged displays. The horizontal screen will automatically be divided according to the number entered. A maximum of 15 displays can be assigned to the horizontal arrangement.  The screen can be divided into a maximum of 100 screens (horizontal and vertical screens multiplied).
PAGE 158
8 System 8.14 Source AutoSwitch Settings MENU [m] System Source AutoSwitch Settings ENTER [ ] Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will automatically search the different video input sources for active video.  Source AutoSwitch When the Source AutoSwitch is On, the display video source will automatically be searched for active video.
PAGE 159
8 System 8.15 General MENU [m] System General ENTER [ ] General Max. Power Saving On Game Mode Off BD Wise On Menu Transparency Medium Sound Feedback Off Auto Power Off Standby Control Auto The displayed image may differ depending on the model. 8.15.1 Max. Power Saving Turns off the product to reduce power consumption after the PC has been left idle for a specified period of time. Available only in PC, DVI, HDMI, DisplayPort mode. 8.15.
PAGE 160
8 System 8.15.3 BD Wise Provides the optimal picture quality for Samsung DVD, Blu-ray and Home Theater products which support BD Wise. When BD Wise is turned On, the picture mode is automatically changed to the optimal resolution. Available when you connect Samsung products that support BD Wise through an HDMI cable to the product. 8.15.4 Menu Transparency Adjust transparency of menu box.  High / Medium / Low 8.15.5 Sound Feedback Your product gives sound feedback when you use product.
PAGE 161
8 System 8.15.8 Lamp Schedule Enables the lamp value to be adjusted to a user-specified value at a specified time in MDC mode. 8.15.9 OSD Display Displays or hides a menu item on the screen.  Source OSD / No Signal OSD / MDC OSD 8.15.10 Power On Adjustment You can set the warm-up time for the screen to turn on after the power button is pressed. (Range: 0 – 50 seconds) A warm-up time that is too short may damage the product due to overvoltage. 8.15.
PAGE 162
8 System 8.16 Anynet+ (HDMI-CEC) MENU [m] 8.16.1 System Anynet+ (HDMI-CEC) ENTER [ ] Anynet+ (HDMI-CEC) What is Anynet+? Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung device has this feature, check if there is an Anynet+ logo on it.
PAGE 163
8 System Anynet+ Menu The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the product. Anynet+ Menu View PC Device List Description Changes Anynet+ mode to PC mode. Shows the Anynet+ device list. (device_name) MENU Shows the menu of the connected device menus. E.g. if a DVD player is connected, the disc menu of the DVD player will appear. (device_name) Tools Shows the tools menu of the connected device. E.g.
PAGE 164
8 System Troubleshooting for Anynet+ Problem Anynet+ does not work. Possible Solution  Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.  Check if the Anynet+ device power cord is properly connected.  Check the Anynet+ device’s Video/Audio/HDMI cable connections.  Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.  Check whether the remote control is Anynet+ compatible.  Anynet+ doesn’t work in certain situations.
PAGE 165
8 System Problem Possible Solution The Anynet+ device does not play. The connected device is not displayed.  You cannot use the play function when Plug & Play (initial setup) is in progress.  Check whether or not the device supports Anynet+ functions.  Check whether or not the HDMI cable is properly connected.  Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.  Search Anynet+ devices again.  Anynet+ requires an HDMI connection.
PAGE 166
8 System 8.19 Reset All MENU [m] System Reset All ENTER [ ] This option returns all the current settings for a display to the default factory settings. (Menu Language, Security, Time, Multi Control and Anynet+ will not be initialized.) 8.20 PC Module Power MENU [m] System PC Module Power ENTER [ ] The PC module can be turned on/off separately from the LFD. PC module: Refers to network boxes or PIM. 8.20.1 Synced Power-On To turn on the PC module without turning on the LFD, select Off.
PAGE 167
9 9.1 Support Software Update MENU [m] Support Software Update ENTER [ ] The Software Update menu lets you upgrade your products software to the latest version.  Current Version: This is the software version already installed in the product. Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade.
PAGE 168
9 Support View this information when your product does not work properly or when you want to upgrade the software. You can find information regarding our call centers and how to download products and software.
PAGE 169
9 9.3 Support Contents Home MENU [m] Support Contents Home ENTER [ ] You can enjoy useful and various contents. 9.3.1 Channel List MENU [m] Support Contents Home ENTER [ Channel List ] You can view all the channel searched. Channel List Added Ch. a 1 1futech a 2 24ore.tv a 3 BBC World a 4 Class News a 5 Coming Soon a 6 R4 DTT No Information A Antenna a 7 C2 a 8 C4 CH Mode Watch Page The displayed image may differ depending on the model.
PAGE 170
9 Support 9.3.2 Channel Manager MENU [m] Support Contents Home Channel Manager ENTER [ ] Display all the channels searched and edit the favorites. Change channel names, view information, and use the delete function. Channel All Added CH.
PAGE 171
9 Support Using Tools  Edit Favorites: Edit selected channels in Favorites.  A Add: Add selected channels to Favorites.  A Delete: Delete selected channels from Favorites.  B : Change the order of channels in Favorites.  C : Copy channels to another Favorites group.  D : Move to another Favorites group.  0~9 : Change the channel by entering a channel number using the remote control.  Return: Return to the previous menu.  Rename Channel: Change a selected channel name.
PAGE 172
9 Support 9.3.5 Source Source allows you to select a variety of sources and change source device names. You can display the screen of a source device connected to the product. Select a source from Source List to display the screen of the selected source. The input source can also be changed by using the SOURCE button on the remote control. The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
PAGE 173
10 AllShare Play Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device. 10.1 What is AllShare Play? Play photo, video or music files saved on a storage device. Wirelessly connect a smartphone to a PC using a wireless network. Play various content using one of the following methods in AllShare Play:  Using internal memory and a USB device: Play video, photo and music files from a USB device. Copy the files to the internal memory.
PAGE 174
10  AllShare Play The screensaver activates if the product is left idle for a period of time specified in Auto Protection Time.  Power-saving mode on some external hard disk drives may automatically deactivate after connecting to the product. File system and formats  Allshare play may not function properly with unlicensed multimedia files.  Media Transfer Protocol (MTP) is not supported.  Supported file systems include FAT16, FAT32 and NTFS (read only).
PAGE 175
10 AllShare Play 10.1.2 Using a USB device Connecting a USB device 1 2 Turn on your product. Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product. 3 A message "Connected Device" appears when the USB device is connected properly. Select type of content to play from Videos, Photos, and Music.  If only one USB device is connected, files saved on the USB device are displayed automatically.
PAGE 176
10 AllShare Play 10.1.3 Connecting to a PC over a network Play photo, video and music files saved on a PC through a network connection in AllShare Play mode.  For details on how to configure a network, refer to the section "7.1 Network Setting".  To view content saved on the PC, connect the product and PC to the same wireless router and visit http://www.samsung.com to download the AllShare PC software. Ensure the product and PC are connected to the same network subnet.
PAGE 177
10 AllShare Play 10.1.4 Using the DLNA features If you connect the product and a source device such as a cell phone or PC to the same network, you can play media content saved on the device such as videos, photos and music. Visit http://www.samsung.com or contact the Samsung Electronics Customer Center for more information. Additional software may need to be installed on your mobile device. Refer to the mobile device user manual for details.
PAGE 178
10 AllShare Play 10.2 Using the Basic AllShare Play Features MENU [m] Support Contents Home AllShare Play ENTER [ ] AllShare A ll Play / My List / Recently Played My List Videos Recently played ﬁles will be displayed here. What's New Updated ﬁles will be displayed here. Photos Playlist Music No playlists have been created. Create a playlist to quickly and easily access your content. Return The displayed image may differ depending on the model. 10.2.
PAGE 179
10 AllShare Play 10.2.2 Playing Selected Files 1 2 Select files from the list of Videos, Photos, or Music files. Press TOOL on the remote control and select Selection Play. The option does not appear if a folder is highlighted by the cursor. 3 Select files and press Play.  c appears for selected files.  To select all the files in the current folder, press Select All.  To deselect all the files, press Deselect All. 10.2.
PAGE 180
10 AllShare Play 10.2.4 Creating a Playlist (Playlist) Create a list of files you want to play continuously. 1 2 Select files from the list of Videos, Photos, or Music files. Press TOOL on the remote control and select Add to Playlist. The option does not appear if a folder is highlighted by the cursor. 3 Select files and press Add. The Add to Playlist page appears. 4 5 6  c appears for selected files.  To select all the files in the current folder, press Select All.
PAGE 181
10 AllShare Play 10.3 My List MENU [m] Support Contents Home AllShare Play My List ENTER [ ] Access desired content more conveniently and quickly. To play files, select files or a playlist (Playlist) and press [  ]. Recently Played: Display video, photo or music files that were recently played. This mode is suitable when playing files again that were played before.  What's New: Display new video, photo or music files that were uploaded to a PC or USB device.
PAGE 182
10 AllShare Play 10.4 Videos MENU [m] Support Contents Home AllShare Play Videos ENTER [ ] 10.4.1 Playing a Video Select the internal memory or a USB device. Select a file from the list of files. Press the [ ] button or [ ▶ ] (Play) button.  The file name appears on the top with its playing time.  If video time information is unknown, the playing time and progress bar are not displayed.  During video playback, you can search using the buttons.
PAGE 183
10 AllShare Play 10.5 Photos MENU [m] Support Contents Home AllShare Play Photos ENTER [ ] 10.5.1 Viewing a Photo (or Slide Show) 1 2 Select the internal memory or a USB device. Select a file from the list of files. Press the [ ] button.  To view files manually, one at a time, press the left or right arrow buttons.
PAGE 184
10 AllShare Play 10.6 Music MENU [m] Support Contents Home AllShare Play Music ENTER [ ] 10.6.1 Playing Music Select the internal memory or a USB device. Select a file from the list of files. Press the [  ] button or [ ▶ ] (Play) button. When the music is playing, you can search using the [ ◀◀ ] (REW) and [ ◀◀ 1 2 ] (FF) button. If the sound is abnormal when you play MP3 files, adjust the Equalizer in the Sound menu. (An overmodulated MP3 file may cause a sound problem.
PAGE 185
10 AllShare Play 10.7 Videos / Photos / Music Play Option menu When playing video or photo files, you can press the TOOLS button to display an Options menu. Below are a series of tables listing the options available and the media each option applies to. Option Name Operations Videos Photos Music View Sort music files grouped by Folder view, Title, Artist, Album or Genre. c Selection Play Select and play files from a list of music files.
PAGE 186
10 AllShare Play Option Name Operations Videos Subtitle Setting Displays the Subtitle Setting. You can set up a subtitle option. c Start Slide Show / Stop Slide Show You can start or stop a slide show. Slide Show Speed You can select the slide show speed during Alternatively, use the remote. ▶ or II Photos Music c button on the the slide show. Alternatively, use the ◀◀ c or button on the remote. ◀◀ Slide Show Effect You can set various slide show effects.
PAGE 187
10 AllShare Play 10.8 Supported Subtitle and AllShare Play file formats 10.8.1 Subtitle External  MPEG-4 timed text (.ttxt)  SAMI (.smi)  SubRip (.srt)  SubViewer (.sub)  Micro DVD (.sub or .txt)  SubStation Alpha (.ssa)  Advanced SubStation Alpha (.ass)  Powerdivx (.psb) Internal  Xsub Container: AVI  SubStation Alpha Container: MKV  Advanced SubStation Alpha Container: MKV  SubRip Container: MKV  MPEG-4 timed text Container: MP4 10.8.
PAGE 188
10 AllShare Play File Extension Type *.flac Codec FLAC FLAC Comments The Seek (jump) function is not supported. Supports up to 2 channel *.ogg OGG Vorbis Supports up to 2 channel *.wma WMA WMA Supports up to WMA 10 Pro 5.1 channel. WMA lossless audio is not supported. 10.8.4 Supported Video Formats File Extension Container Video Codec Resolution Frame rate (fps) Bit rate (Mbps) DIVX 3.11 / 4.x / 5.x / 6.x *.avi *.mkv *.asf MPEG4 SP / ASP *.wmv *.mp4 *.mov *.3gp *.vro *.mpg *.
PAGE 189
10 AllShare Play  Video content will not play, or not play correctly, if there is an error in the content or the container.  Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec listed in the table above.  If the Index Table is in error, the Seek (Jump) function is not supported.  You may experience file stuttering while playing a video through a network connection.
PAGE 190
11 MagicInfo Lite 11.1 File Formats Compatible with MagicInfo Lite Player [Read before using MagicInfo Lite Player]  The file system supports FAT16, FAT32 and NTFS.  A file with a vertical and horizontal resolution larger than the maximum resolution cannot be played. Check the vertical and horizontal resolution of the file.  Video that does not contain audio data is not supported. Check that the video file contains audio data.  Check the supported video and audio Codec types and Versions.
PAGE 191
11 MagicInfo Lite 11.1.1 Contents File Extension Container *.avi Video Codec Resolution Frame rate (fps) Bit rate (Mbps) Audio Codec DIVX 3.11 / 4.x / 5.x / 6.x *.mkv *.asf MPEG4 SP / ASP *.wmv *.mp4 *.mov AVI *.3gp MKV *.vro ASF *.mpg MP4 *.mpeg 3GP *.ts VRO *.tp VOB *.trp PS *.flv TS *.vob AC3 LPCM H.264 BP / MP / HP AAC 1920 x 1080 Motion JPEG 30 HE-AAC WMA 6 ~ 30 DD+ MPEG(MP3) Window Media Video v9 DTS Core G.711(ALaw, μ-Law) MPEG2 *.svi *.m2ts MPEG1 *.
PAGE 192
11 MagicInfo Lite Video  Video content without audio is not supported.  3D video is not supported.  Content with a resolution larger than the resolution specified in the table above is not supported.  Video content with a Bit rate or Frame rate larger than the rate specified in the table above can cause choppy video during playback.  Video content will not play, or not play correctly, if there is an error in the content or the container.
PAGE 193
11 MagicInfo Lite Flash  Compatible with Flash 10.1  Flash Animation   Compatible file format : SWF Resolution : 1280 x 720  Caution - Performance comparable to Flash Player on a Windows operating system cannot be guaranteed  Optimization is needed during content creation Flash Video  Compatible file format : FLV  Video  - Codec : H.264 BP - Resolution : 1920 x 1080 Audio -  Codec : H.
PAGE 194
11 MagicInfo Lite PDF  Compatible document file formats   Extension : pdf Functions not supported  Content less than 1 pixel not supported because of performance degradation issue.  Masked Image, Tiled Image content not supported.  Content with Rotated Text, not supported.  3D Shadow Effects not supported.
PAGE 195
11 MagicInfo Lite 11.2 MagicInfo Lite Player 11.2.1 Network Schedule Connecting to a server Network setup To run MagicInfo Lite, connect to a network. Refer to 126 page for details about the Network Settings menu. Server setup Go to MENU Network MagicInfo Lite Settings Server. Next, enter the server information. (E.g.: http://192.168.0.10:7001/MagicInfo/) Server Server http://192.168.0.
PAGE 196
11 MagicInfo Lite MagicInfo Lite Settings MENU [m] Support Contents Home MagicInfo Lite ENTER [ ] Press the MagicInfo Lite button on the remote control. You can view whether the server is connected (approval) in the MagicInfo Lite menu screen. To view whether the server is connected when a network schedule is running, press INFO on the remote. 1 Select MagicInfo Lite Player in the MagicInfo Lite menu.
PAGE 197
11 MagicInfo Lite Approving a connected device from the server 1 Access the server you have assigned to your device. 2 3 Enter your ID and password to log in. 4 Select Lite Device from the menus on the left. Select Device from the top menu bar.
PAGE 198
11 MagicInfo Lite 5 Select View Unapproved Lite Device from the sub-menus of Lite Device. 6 7 Select the Approve button for your device from the list of unapproved Lite devices. Enter the information required to approve the device.  Device Name: Enter the device name.  Device Model Name: Select your device model.  Device Group: Select  Location: Enter the current location of the device. to specify the group.
PAGE 199
11 MagicInfo Lite  For further details on how to configure a schedule, refer to the .  If a device is deleted from the list of devices approved by the server, the device will reboot to reset its settings. Setting the current time A schedule may not run if the time set on the device is different from the server's current time. 1 Go to the tabs Device 2 3 Select your device. Time. Select Clock Set, and sync the time with the server.
PAGE 200
11 MagicInfo Lite 11.2.2 Local Schedule Run a schedule created by Local Schedule Manager. Go to Local Schedule Manager Select the content you want to run This menu is disabled if there was no schedule run previously in Local Schedule Manager. 1 Select Local Schedule in the MagicInfo Lite Player menu screen. Run a schedule create by Local Schedule Manager.
PAGE 201
11 MagicInfo Lite 11.2.3 Internal AutoPlay Running Internal AutoPlay The option is enabled only when there is at least one content item, except for music files, in Internal Memory. 1 Select Internal AutoPlay in the MagicInfo Lite Player menu screen.  Play content, which has been copied to Internal Memory, in alphabetical order.
PAGE 202
11 MagicInfo Lite 11.2.4 USB AutoPlay Running Internal AutoPlay 1  The option is enabled only when there is at least one content item, except for music files, in USB AutoPlay.  Ensure a USB device is inserted. Be sure to create a folder named "MagicInfoSlide" in the USB device and put content in the folder.  USB AutoPlay automatically runs when a USB device is connected, regardless of whether the Internal Memory is running. Select USB AutoPlay in the MagicInfo Lite Player menu screen.
PAGE 203
11 MagicInfo Lite 11.3 Local Schedule Manager Configure the settings for playback from Local Schedule. Alternatively, select and play content from internal or USB memory according to the customized playback sequence. 11.3.1 Registering a Local Schedule 1 Select Local Schedule Manager in the MagicInfo Lite menu screen.
PAGE 204
11 3 MagicInfo Lite Select Time to set the time you want to play content. Create Time 12 : --:-- am ~ --:-- pm 00 am ~ Content Time 12 : 00 am No Item --:-- am ~ --:-- pm Content Save No Item Cancel Return  A maximum of 24 schedules can be created.  If more than one schedule is created, the start time must be different for each schedule. (Example of an incorrect setting: 12:00 am - 12:00 am / 12:00 am - 11:00 pm) 4 Select Content to specify the content you want to play.
PAGE 205
11 5 MagicInfo Lite Select Duration Duration Content Duration Menu1.jpg 00:00:05 Menu2.jpg 00:00:05 Up Down Save Cancel Return Specify the sequence and time duration to play content files.  Changing the playing sequence Select a content file and change the sequence using the Up or Down button.  Duration Set the duration to play content.  Duration cannot be specified for videos.  Duration must be at least 5 seconds. Press Save to save the settings. 6 Select Save.
PAGE 206
11 7 MagicInfo Lite Check that the schedule has been added to the Local Schedule Manager. Local Schedule Manager Storage Internal Memory No Playing Schedule Create Edit Delete All Schedule 2012.01.01_1834.
PAGE 207
11 MagicInfo Lite 11.3.2 Modifying a Local Schedule Ensure at least one Local Schedule is registered. 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. MagicInfo Lite MagicInfo Lite Player Local Schedule Manager Content Manager Close Settings Mode Server USB Local Schedule Connected Connected Return 2 Select the local schedule you want to modify. Local Schedule Manager Storage Internal Memory No Playing Schedule Create Edit Delete All Schedule 2012.01.01_1834.
PAGE 208
11 4 MagicInfo Lite Change the details of the local schedule. Next, select Save. Edit Time Content Time Content Time Content 12:00 am ~ 12:00 pm Delete Menu1.
PAGE 209
11 MagicInfo Lite 11.3.3 Deleting a Local Schedule Ensure at least one Local Schedule is registered. 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. MagicInfo Lite MagicInfo Lite Player Local Schedule Manager Content Manager Close Settings Mode Server USB Local Schedule Connected Connected Return 2 Select the local schedule you want to delete. Next, select Delete. Local Schedule Manager Storage Internal Memory No Playing Schedule Create Edit Delete All Schedule 2012.01.
PAGE 210
11 MagicInfo Lite 11.3.4 Running a Local Schedule Ensure at least one Local Schedule is registered. 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. MagicInfo Lite MagicInfo Lite Player Local Schedule Manager Content Manager Close Settings Mode Server USB Local Schedule Connected Connected Return 2 Select the local schedule you want to run. Next, select Run. Local Schedule Manager Storage Internal Memory No Playing Schedule Create Edit Delete All Schedule 2012.01.
PAGE 211
11 MagicInfo Lite 11.3.5 Stopping a Local Schedule This function is enabled only when a schedule is running. Selecting Stop will change the running mode from local schedule to network schedule. 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. MagicInfo Lite MagicInfo Lite Player Local Schedule Manager Content Manager Close Settings Mode Server USB Local Schedule Connected Connected Return 2 Select Stop. Local Schedule Manager Storage Internal Memory [Internal]2012.01.
PAGE 212
11 MagicInfo Lite 11.3.6 Viewing the details of a Local Schedule 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. MagicInfo Lite MagicInfo Lite Player Local Schedule Manager Content Manager Close Settings Mode Server USB Local Schedule Connected Connected Return 2 Select the local schedule you want to view the details of. Local Schedule Manager Storage Internal Memory No Playing Schedule Create Edit Delete All Schedule 2012.01.01_1834.
PAGE 213
11 3 MagicInfo Lite The details of the schedule will be displayed. Information 2012.01.01_1834.lsch 12:00 am~12:00 pm, 2 File(s) - Menu1.jpg Menu2.
PAGE 214
11 MagicInfo Lite 11.3.7 Copying a Local Schedule (Local Schedule) 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. MagicInfo Lite MagicInfo Lite Player Local Schedule Manager Content Manager Close Settings Mode Server USB Local Schedule Connected Connected Return 2 Select a storage device where the local schedule files to copy are saved. Local Schedule Manager Internal Memory Internal Memory Storage Playing Schedule No P USB Create Edit Delete All Schedule 2012.01.
PAGE 215
11 3 MagicInfo Lite Select local schedule files and press Copy. Local Schedule Manager Storage Internal Memory No Playing Schedule Create Edit Delete All Schedule 2012.01.01_1834.lsch Run Info Copy Close Return 4 A window appears asking if you want to copy the files to the Internal Memory or USB memory device. Select Yes to copy the files.
PAGE 216
11 MagicInfo Lite 11.4 Content Manager 11.4.1 Copying content 1 Select Content Manager in the MagicInfo Lite menu screen. MagicInfo Lite MagicInfo Lite Player Local Schedule Manager Content Manager Close Settings Mode Server USB Local Schedule Connected Connected Return 2 Select the content you want to copy. Next, select Copy.  If content under Internal Memory is selected: You can copy the content under Internal Memory to USB memory.
PAGE 217
11 MagicInfo Lite 11.4.2 Deleting content 1 Select Content Manager in the MagicInfo Lite menu screen. MagicInfo Lite MagicInfo Lite Player Local Schedule Manager Content Manager Close Settings Mode Server USB Local Schedule Connected Connected Return 2 Select the content you want to delete. Next, select Delete.  Content under Internal Memory and USB memory can be deleted at the same time. Content Manager Internal Memory Menu3.jpg USB Folder1 Menu4.jpg Menu1.jpg Menu2.
PAGE 218
11 MagicInfo Lite 11.5 Settings Settings Content Default Duration Content Ratio Image Effect None Default Content Menu1.jpg Screen Layout Landscape Close Delete All Content Safety Remove USB Return 11.5.1 Content Default Duration Specify the duration to play content.  Image Viewer Time, PPT Viewer Time, PDF Viewer Time, Flash Viewer Time The duration must be at least 5 seconds. 11.5.2 Content Ratio Specify the display aspect ratio by type when playing content.
PAGE 219
11 MagicInfo Lite 11.5.5 Screen Layout Change the screen orientation to landscape or portrait view.  Landscape / Portrait 11.5.6 Delete All Content Delete all the content files in Internal Memory. 11.5.
PAGE 220
11 MagicInfo Lite 11.6 When Content is Running 11.6.1 Viewing the details of the content that is running Press the INFO button on the remote control.
PAGE 221
11 MagicInfo Lite 11.6.2 Changing the settings for the content that is running Press the TOOLS button on the remote control. Tools Picture Mode Standard Sound Mode Standard PIP Off Background Music Off Background Music Setting Safety Remove USB Return You can change the Picture Mode or Sound Mode setting or safely remove a USB device (Safely Remove USB) while content is playing by pressing the TOOLS button on the remote control.
PAGE 222
12 Troubleshooting Guide 12.1 Requirements Before Contacting Samsung Customer Service Center 12.1.1 Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check if your product is operating normally by using the product test function. If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
PAGE 223
12 Troubleshooting Guide 12.1.3 Check the followings. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connection is secure. ("2.2 Connecting and Using a PC") Blank spaces are found at the top and bottom of the screen when an HDMI or HDMI-DVI cable is connected to the product and PC. Blank spaces on the screen are not caused by the product.
PAGE 224
12 Troubleshooting Guide Screen issue The screen is not clear. The screen is blurry. Adjust Coarse and Fine. Remove any accessories (video extension cable, etc) and try again. Set the resolution and frequency to the recommended level. The screen appears unstable and shaky. There are shadows or ghost images left on the screen. Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product.
PAGE 225
12 Troubleshooting Guide Remote control issue The remote control does not work. Make sure that the batteries are correctly in place (+/-). Check if the batteries are flat. Check for power failure. Make sure that the power cord is connected. Check for any special lighting or neon signs switched on in the vicinity. Source device issue A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is booting, have your PC serviced.
PAGE 226
12 Troubleshooting Guide 12.2 Q & A Question How can I change the frequency? Answer Set the frequency on your graphics card.  "Windows XP": Go to Control Panel Themes Display Settings Appearance and Advanced Monitor and adjust the frequency in Monitor Settings.  "Windows ME/2000": Go to Control Panel Settings Advanced Display Monitor and adjust the frequency in Monitor Settings.
PAGE 227
12 Troubleshooting Guide Question How can I change the resolution? Answer  "Windows XP": Go to Control Panel Themes  Display Appearance and Settings and adjust the resolution. "Windows ME/2000": Go to Control Panel Display Settings and adjust the resolution.  "Windows Vista": Go to Control Panel Personalization Personalize Appearance and Display Settings and adjust the resolution.
PAGE 228
13 Specifications 13.1 General Model Name Panel DE40C Size 40 inches (101 cm) Display area 885.6 mm (H) x 498.15 mm (V) 34.866 inches (H) x 19.612 inches (V) Dimensions (W x H x D) 919.6 x 532.0 x 35.1 mm 36.2 x 20.9 x 1.4 inches Weight 13.5 kg / 29.8 Ibs VESA 200 x 200 mm / 7.9 x 7.9 inches Model Name Panel DE46C DE55C Size 46 inches (116 cm) 54.6 inches (138 cm) Display area 1018.08 mm (H) x 572.67 mm (V) 1209.6 mm (H) x 680.4 mm (V) 40.082 inches (H) x 22.546 inches (V) 47.
PAGE 229
13 Specifications Model Name Signal connectors DE40C / DE46C / DE55C Input ANT IN(ATV/DTV), AV IN/COMPONENT IN(common), RGB IN(PC D-Sub), DVI IN, HDMI IN, DP IN, RGB/DVI/HDMI/AV/COMPONENT AUDIO IN, RJ45, RS232C IN, IR/AMBINET SENSOR IN Output IR OUT, AUDIO OUT, DP OUT(LOOP OUT), RS232C OUT USB 2 DOWN Environmental considerations Operating Temperature : 32˚F ~ 104˚F (0˚C ~ 40˚C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4˚F ~ 113˚F (-20˚C ~ 45˚C) Humidity : 5 % ~ 95 %, non-c
PAGE 230
13 Specifications 13.2 PowerSaver The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power-savign mode only functions when the product is connected to a PC with a power-saving function.
PAGE 231
13 Specifications 13.3 Standard Signal Mode Table  This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your monitor.  Check the frequency when you exchange a CDT monitor (connected to a PC) for an LCD monitor.
PAGE 232
13 Specifications Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1366 x 768 47.712 59.790 85.500 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900(RB) 60.000 60.000 108.000 +/+ VESA, 1680 x 1050 65.290 59.954 146.250 -/+ VESA, 1920 x 1080 67.500 60.000 148.500 +/+ Horizontal Frequency The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle.
PAGE 233
13 Specifications 13.4 License Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks. & DTS 2.0+ Digital Out and the DTS logos are trademarks of DTS, Inc. Product Includes software. Inc. All Rights Reserved.
PAGE 234
Appendix Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca http://www.samsung.com/ca_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com LATIN AMERICA ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 4004-0000 http://www.samsung.
PAGE 235
Appendix LATIN AMERICA GUATEMALA 1-800-299-0013 http://www.samsung.com/latin (Spanish) http://www.samsung.com/ latin_en (English) HONDURAS 800-27919267 http://www.samsung.com/latin (Spanish) http://www.samsung.com/ latin_en (English) JAMAICA 1-800-234-7267 http://www.samsung.com NICARAGUA 00-1800-5077267 http://www.samsung.com/latin (Spanish) http://www.samsung.com/ latin_en (English) PANAMA 800-7267 http://www.samsung.com/latin (Spanish) http://www.samsung.
PAGE 236
Appendix Responsibility for the Pay Service (Cost to Customers) When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician in the following cases. Not a product defect Cleaning of the product, Adjustment, Explanation, Re-installation and etc.  If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.
PAGE 237
Appendix Optimum Picture Quality and Afterimage Burn-in Prevention Optimum Picture Quality  To enjoy the optimum picture quality, go to Control Panel on your PC and adjust the resolution and refresh rate as follows. The picture quality of TFT-LEDs may degrade if the optimum resolution is not selected.
PAGE 238
Appendix Prevention of Afterimage Burn-in What is afterimage burn-in? Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that control the liquid crystals.
PAGE 239
Appendix  Powering Off, Screen Saver and Power Saving Mode  Power off the product for 2 hours after using it for 12 hours.  Power off the product for 4 hours after using it for 20 hours.  Go to Display Properties > Power Supply on your PC and set the product to power off as required.  Using a screen saver is recommended. It is best to use a single-color or moving-image screen saver.
PAGE 240
Appendix Terminology Dot Pitch The product and screen consist of red, green and blue dots. A shorter distance between the dots produces a higher resolution. Dot pitch refers to the distance between the shortest distance between dots of the same color. Dot pitch is measured in millimeters. Vertical Frequency The product displays a single image many times per second (like a fluorescent light that flickers) to display an image for a viewer to see.
PAGE 241
Appendix Multiple Display Control (MDC) MDC (Multiple Display Control) is an application that allows multiple display devices to be controlled simultaneously using a PC. Communication between a PC and monitor takes place using RS232C (serial data transmission) and RJ45 (LAN) cables. DVD (Digital Versatile Disc) DVD refers to a CD-sized mass storage disk where you can save multimedia (audio, video or game) applications using MPEG-2 video compression technology.
PAGE 242
Index A D Advanced Settings 113 Device Name 138 AllShare Settings 137 Dimensions 38 Antenna 65 DivX® Video On Demand 165 Antenna (Air/Cable) 123 Anynet+(HDMI-CEC) 162 Auto Adjustment 112 Auto Program 124 Auto Protection Time 152 B Batteries 33 Before Connecting 56 Before Installing the Product (Installation Guide) 36 E Eco Solution 145 Edit Name 172 Energy Saving 145 F File Formats Compatible with MagicInfo Lite Player 190 Fine Tune 125 Broadcast Audio Options 121 G Game Mode 159 C General 1
PAGE 243
Index N Screen Position 157 Network Setting 126 Security 148 Network Status 134 Settings 218 No Signal Power Off 145 Setup 139 Sleep Timer 142 P Parts 28 PC connection 57 PC Module Power 166 Photos 183 Picture Mode 107 Picture Options 116 Picture Size 109 Soft AP 136 Software Update 167 Sound Effect 120 Sound Mode 119 Source AutoSwitch Settings 158 Speaker Settings 121 Standard 108 Standard Signal Mode Table 231 PIP 151 Port 30 T PowerSaver 230 Ticker 155 Problem report 222 Time 141 Q U Q