User Manual SyncMaster S23A950D / S27A950D The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality. 2011 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics. Microsoft, and Windows are registered trademarks of Microsoft Corporation.
Before Using the Product Icons used in this manual The following images are for reference only. Real-life situations may differ from what is shown in the images. Symbols for safety precautions A serious or fatal injury may result if instructions are not followed. Warning Caution Personal injury or damage to properties may result if instructions are not followed. Activities marked by this symbol are prohibited. Instructions marked by this symbol must be followed.
Before Using the Product Cleaning Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. Take the following steps when cleaning. 1. Power off the monitor and computer. 2. Disconnect the power cord from the monitor. Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result. 3. Wipe the monitor with a clean, soft and dry cloth.
Before Using the Product Securing the Installation Space z Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product. The appearance may differ depending on the product. 10 cm 10 cm 10 cm 10 cm 10 cm Precautions for storage High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby.
Before Using the Product Warning Do not use a damaged power cord or plug, or a loose power socket. z An electric shock or fire may result. Do not plug many products into the same power socket. z Otherwise, the socket may overheat and cause a fire. Do not touch the power plug with wet hands. z Otherwise, an electric shock may result. Insert the power plug all the way in so it is not loose. z An unstable connection may cause a fire.
Before Using the Product Caution Do not unplug the power cord when the product is in use. z The product may become damaged by an electric shock. Do not use the power cord for products other than authorized products supplied by Samsung. z ! An electric shock or fire may result. Keep the power socket where the power cord is connected unobstructed. z If any problem occurs in the product, unplug the power cable to completely cut the power to the product.
Before Using the Product Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.). z The product may fall and break or cause a personal injury. z Using the product in an area with excess vibration may damage the product or cause a fire. Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke. z ! An electric shock or fire may result.
Before Using the Product Put down the product carefully. z The product may fall and break or cause a personal injury. ! SAMSUNG ! Installing the product in an unusual place (a place exposed to a lot of fine particles, chemical substances or extreme temperatures, or an airport or train station where the product should operate continuously for an extended period of time) may seriously affect its performance.
Before Using the Product During a lightning or thunderstorm, power off the product and remove the power cable. z ! An electric shock or fire may result. Do not drop objects on the product or apply impact. z An electric shock or fire may result. ! Do not move the product by pulling the power cord or any cable. z Otherwise, the power cable may be damaged and product failure, an electric shock or fire may result. If a gas leakage is found, do not touch the product or power plug.
Before Using the Product Caution Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. z ! If you are not going to use the product for an extended period of time, activate power-saving mode or a moving-picture screen saver. -_! Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc).
Before Using the Product Do not hold the monitor upside-down or move it by holding the stand. z The product may fall and break or cause a personal injury. Do not use humidifiers or stoves around the product. z An electric shock or fire may result. Rest your eyes for more than 5 minutes for every 1 hour of product use. z Eye fatigue will be relieved. ! Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.
Before Using the Product Correct posture to use the product Use the product in the correct posture as follows: z Straighten your back. z Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at the screen. Keep your eyes directly in front of the screen. z Adjust the angle so light does not reflect on the screen. z Keep your forearms perpendicular to your upper arms and level with the back of your hands. z Keep your elbows at about a right angle.
Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS 3D 2 Copyright 3 3 Icons used in this manual Symbols for safety precautions 4 Cleaning 4 5 5 Cleaning Securing the Installation Space Precautions for storage 5 Safety Precautions 5 7 9 Electricity and Safety Installation Operation 13 Correct posture to use the product 19 Checking the Contents 19 20 Removing the Packaging Checking the Components 21 Parts 21 23 24 24 25 Frontal Buttons Reverse Side Tidying Up the Connected Cables
Table Of Contents CONNECTING AND USING A SOURCE DEVICE SCREEN SETUP CONFIGURING TINT 32 Before Connecting 32 Pre-connection Checkpoints 32 Connecting the Power 33 Connecting and Using a PC 33 35 36 37 Connecting to a PC Driver Installation Setting Optimum Resolution Changing the Resolution Using a PC 39 Connecting to a Video Device 39 Connection Using the HDMI Cable 39 Connecting Headphones 40 MAGIC 40 41 42 SAMSUNG MAGIC Angle SAMSUNG MAGIC Bright Configuring SAMSUNG MAGIC Color 43
Table Of Contents RESIZING OR RELOCATING THE SCREEN SETUP AND RESET 48 Blue 48 Configuring Blue 48 Color Tone 49 Configuring the Color Tone Settings 50 Gamma 50 Configuring Gamma 51 Image Size 51 Changing the Image Size 52 H-Position 52 Configuring H-Position 52 V-Position 52 Configuring V-Position 53 Menu H-Position 53 Configuring Menu H-Position 53 Menu V-Position 54 Configuring Menu V-Position 55 ECO 55 56 58 59 Eco Motion Sensor Eco Light Sensor Eco Saving Eco Icon
Table Of Contents INFORMATION MENU AND OTHERS TROUBLESHOOTING GUIDE SPECIFICATIONS 63 Display Time 63 Configuring Display Time 64 Key Repeat Time 64 Configuring Key Repeat Time 65 Customized Key 65 Configuring Customized Key 65 Off Timer On/Off 65 Configuring Off Timer On/Off 66 Off Timer Setting 66 Configuring Off Timer Setting 67 Reset 67 Initializing Settings (Reset) 68 INFORMATION 68 Displaying INFORMATION 68 Configuring Brightness in the Startup Screen 68 Configuring
Table Of Contents APPENDIX 81 Contact SAMSUNG WORLD WIDE 87 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) 88 Terminology INDEX Table Of Contents 18
1 1.1 Preparations Checking the Contents 1.1.1 Removing the Packaging 1 Open the packaging box. Be careful not to damage the product when you open the packaging with a sharp instrument. 2 Remove the Styrofoam from the product. 3 Check the components and remove the Styrofoam and plastic bag. 4 z The appearance of actual components may differ from the image shown. z This image is for reference only. Store the box in a dry area so that it can be used when moving the product in the future.
1 Preparations 1.1.2 Checking the Components z Contact the dealer from whom you purchased the product if any item is missing. z The appearance of the components and items sold separately may differ from the image shown. Components Quick Setup Guide Warranty User Manual (Not available in some locations) Cleaning cloth Power cable DC power adapter 3D Glasses & 3D Glasses User Manual DVI-Dual cable Wire holders z Components may differ in different locations.
1 1.2 Preparations Parts 1.2.1 Frontal Buttons The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. z If the MENU button is not visible, lightly tap the area around the [ become visible. ] button. The MENU button will z The onscreen display menu only appears when the MENU button light is lit. z The button light will remain on for 10 seconds and then dim.
1 Preparations Icons Description z Open or close the onscreen display (OSD) menu, or return to the last menu. z OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings. To lock the OSD control, press the MENU button [ m ] for five seconds. m To unlock the locked OSD control, press the MENU button [ m ] for more than five seconds. If the OSD control is locked, z Brightness, Contrast and 3D can be adjusted, and INFORMATION can be viewed.
1 Preparations 1.2.2 Reverse Side The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. DISPLAYPORT IN Port DVI IN HDMI IN DC 14V Description Connects to a source device using an DP cable. Connects to a source device via a DVI cable. Connects to a source device using an HDMI cable. Connects to an audio output device such as headphones. Connects to the DC power adapter.
1 Preparations 1.2.3 Tidying Up the Connected Cables Tidy up the cables using the cable holder on the back of the stand. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. 1.2.4 Kensington Lock An anti-theft lock allows you to use the product securely even in public places. The locking device shape and locking method depend on the manufacturer.
1 Preparations 1.2.5 Adjusting the Product Tilt The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. 20° z You can adjust the tilt of your monitor. z Hold the lower part of the product and adjust the tilt carefully.
2 3D This feature allows you to view 3D content such as 3D movies. You can view 3D content using(SyncMaster-dedicated) Samsung 3D glasses. 2.1 3D z You can purchase "SyncMaster-dedicated 3D glasses (model name: SSG-M3750CR)" separately. Contact the dealer you purchased the product from for details about purchasing the 3D glasses. z The product may not be compatible with 3D glasses other than the model specified above. z Power off the 3D glasses if you will not be using them.
2 3D Configuring the 3D Mode 1 2 3 4 Press [ m ] on the product. Press [ ] to move to Picture and press [ Press [ ] to move to 3D and press [ Press [ ] to move to 3D Mode and press [ ] on the product. ] on the product. ] on the product. The following screen will appear. 3D 3D Mode Depth L/R Change 3D→2D : Off 2D→3D Frame Sequential Top-Bottom Side-by-Side Return Move Enter z Off: Disable the 3D Mode function. z 2D → 3D: Converts a normal video to 3D video.
2 3D 4 Press [ ] to move to Depth and press [ ] on the product. The following screen will appear. 3D Modo 3D Volver : 3D→2D : Cambio I/D : Imagen I/D 5 3D→2D Volver 5 6 Adjust the Depth using the [ Adjust Intro ] button. The selected option will be applied. 2.1.3 L/R Change Switch the left image to the right image, and vice versa. Configuring the L/R Change 1 2 3 4 Press [ m ] on the product. Press [ ] to move to Picture and press [ ] on the product.
2 3D Configuring the 3D → 2D 1 2 3 4 Press [ m ] on the product. Press [ ] to move to Picture and press [ Press [ ] to move to 3D and press [ Press [ ] to move to 3D → 2D and press [ ] on the product. ] on the product. ] on the product. The following screen will appear. 3D Modo 3D : Frame Seq. Profundidad Cambio I/D : Imagen I/D 3D→2D : Des På Volver 5 6 2.2 z Off z On Press [ Mover ] to move to the option you want and press the [ Intro ]. The selected option will be applied.
2 2.4 3D Playing 3D Games on a PC First, install the SyncMaster 3D GAME Launcher (TriDef 3D) software. SyncMaster 3D Game Launcher (TriDef 3D) is a game driver that allows you to play games in 3D on a PC. 1 2 3 4 Set your monitor as the default monitor for the PC. Install the "SyncMaster 3D Game Launcher (TriDef 3D)" software provided on a CD. z Install the software following the instructions displayed. z Alternatively, download and install the software from www.tridef.com/syncmaster.
2 2.5 3D Precautions when Viewing 3D Video z The 3D effect may be experienced differently depending on the viewer. You may not notice the 3D effect at all if you have a prescription for one eye that is very different from the other eye. z When viewing a 3D video under a fluorescent lamp or 3-wavelength lamp, you may notice a small amount of screen flickering.
3 3.1 Connecting and Using a Source Device Before Connecting 3.1.1 Pre-connection Checkpoints z Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. z Do not connect the power cable until all connections are completed. Connecting the power cable during connection may damage the product. z 3.2 Check the types of ports at the back of the product you want to connect.
3 3.3 Connecting and Using a Source Device Connecting and Using a PC 3.3.1 Connecting to a PC z Do not connect the power cable before connecting all other cables. z Ensure you connect a source device first before connecting the power cable. z Select a connection method suitable for your PC. Connecting parts may differ in different products. Connection Using the DVI Cable DVI IN 1 2 Connect the DVI cable to the DVI port on the back of the product and the DVI port on the PC.
3 Connecting and Using a Source Device Connection Using an HDMI-DVI Cable HDMI IN 1 Connect the HDMI-DVI cable to the HDMI port on the back of the product and the DVI port on the PC. 2 Connect the DC power adapter to the product and a power socket, and turn on the power switch on the PC. Audio is not available if the PC and product are connected via the HDMI-DVI port.
3 Connecting and Using a Source Device Connection Using an DP Cable (Digital Type) DISPLAYPORT IN 1 2 Connect the DP cable to the DP port on the back of the product and the DP port on the PC. Connect the DC power adapter to the product and a power socket, and turn on the power switch on the PC. Be sure to connect an audio output device such as headphones or speakers to [ ] on the product to hear audio. 3.3.
3 Connecting and Using a Source Device 3.3.3 Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase. Select a language and change the resolution to the optimum value. The optimal resolution for this monitor is as follows: 1920 x 1080 60Hz Follow the above settings to get the resolution. English Language 1 2 Press [ Enter ] to move to the language you want and press the [ ].
3 Connecting and Using a Source Device 3.3.4 Changing the Resolution Using a PC z Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. z The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP Go to Control Panel 1 → Display → Settings and change the resolution.
3 Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel → Display → Screen Resolution and change the resolution.
3 3.4 Connecting and Using a Source Device Connecting to a Video Device z Do not connect the power cable before connecting all other cables. z Ensure you connect a source device first before connecting the power cable. z The product can be connected to a video device. Connecting parts may differ in different products. 3.4.1 Connection Using the HDMI Cable HDMI IN 1 2 Connect an HDMI cable to the HDMI ports on the product and video device. Press [ ] to change the input source to HDMI.
4 4.1 Screen Setup Configure the screen settings such as brightness and color tone. MAGIC This feature provides the viewing angle, brightness, and tint to suit your preferences. 4.1.1 SAMSUNG MAGIC Angle Angle allows you to configure the settings to obtain the optimum picture quality according to your viewing angle. You can enjoy similar picture quality to when you view directly in front of the product by selecting a viewing mode appropriate for each viewing angle.
4 Screen Setup Lean Back Mode 2 z ③ : Select this option to view from a place lower than Lean Back Mode 1 ② mode. 5 6 ④ : Select this option to view from a place higher than the product. z Standing Mode z Side Mode z Group View: Select this option for more than one viewer to view from places z Custom: Lean Back Mode 1 will be applied by default if Custom is selected. Press [ ⑤ : Select this option to view from either side of the product.
4 Screen Setup Dynamic Contrast: Obtain balanced brightness through automatic contrast adjustment. z In AV mode MAGIC SAMSUNG MAGIC Angle SAMSUNG MAGIC Bright SAMSUNG MAGIC Color : Off : Dynamic Standard : Movie Custom Return 5 6 Move Enter z Dynamic: This mode is suitable when the ambient light is bright. z Standard: This mode is generally suitable for any environment. z Movie: This mode reduces eye fatigue. z Custom: Customize the contrast and brightness as required.
4 Screen Setup 5 6 4.2 z Off: Disable z Demo: Compare normal screen mode with z Full: Obtain a vivid picture quality for all areas including the flesh colors in the picture. z Intelligent: Improve the chroma for all areas except the flesh colors in the picture. Press [ Color. Color mode. ] to move to the option you want and press the [ ]. The selected option will be applied. Brightness Adjust the general brightness of the picture.
4 Screen Setup z This menu is not available when Bright is in Cinema or Dynamic Contrast mode. 4.3.1 Configuring Contrast 1 2 3 Press [ m ] on the product. Press [ ] to move to Picture and press [ Press [ ] to move to Contrast and press [ ] on the product. ] on the product. The following screen will appear. PICTURE 3D MAGIC Brightness 50 Contrast 75 Sharpness 60 Response Time Normal HDMI Black Level Low Return 4 4.
4 4.5 Screen Setup Response Time Accelerate the panel response rate to make video appear more vivid and natural. z It is best to set Response Time to Normal or Faster when you are not viewing a movie. z The functions available on the monitor may vary depending on the model. Refer to the actual product. 4.5.1 Configuring Response Time 1 2 3 Press [ m ] on the product. Press [ ] to move to Picture and press [ ] on the product. Press [ ] to move to Response Time and press [ ] on the product.
4 Screen Setup 3 Press [ ] to move to HDMI Black Level and press [ ] on the product. The following screen will appear. PICTURE 3D MAGIC Brightness 50 Contrast 75 Sharpness 60 Response Time HDMI Black Level Return Nomal Low Move Enter z Normal: Select this mode when there is no contrast ratio degradation. z Low: Select this mode to reduce the black level and increase the white level when there is a contrast ratio degradation.
5 Configuring Tint Adjust the tint of the screen. This menu is not available when Bright is set to Cinema or Dynamic Contrast mode. 5.1 Red Adjust the value of the color red in the picture. (Range: 0~100) A higher value will increase the intensity of the color. This menu is not available when Color is in Full or Intelligent mode. 5.1.1 Configuring Red 1 2 3 Press [ m ] on the product. Press [ ] to move to COLOR and press [ Press [ ] to move to Red and press [ ] on the product.
5 Configuring Tint 3 Press [ ] to move to Green and press [ ] on the product. The following screen will appear. COLOR Red 50 Green 50 Blue Color Tone Normal Gamma Mode1 Return 4 5.3 Adjust the Green using the [ 50 Adjust Enter ] button. Blue Adjust the value of the color blue in the picture. (Range: 0~100) A higher value will increase the intensity of the color. This menu is not available when Color is in Full or Intelligent mode. 5.3.
5 Configuring Tint z This menu is not available when Angle is enabled. z This menu is not available when Color is in Full or Intelligent mode. 5.4.1 Configuring the Color Tone Settings 1 2 3 Press [ m ] on the product. Press [ ] to move to COLOR and press [ ] on the product. Press [ ] to move to Color Tone and press [ ] on the product. The following screen will appear.
5 Gamma Adjust the mid-range brightness (Gamma) of the picture. This menu is not available when Angle is enabled. 5.5.1 Configuring Gamma 1 2 3 Press [ m ] on the product. Press [ ] to move to COLOR and press [ ] on the product. Press [ ] to move to Gamma and press [ ] on the product. The following screen will appear. COLOR Red 50 Green 50 Blue Color Tone Normal Gamma 5.
6 6.1 Resizing or Relocating the Screen Image Size Change the picture size. 6.1.1 Changing the Image Size 1 2 3 Press [ m ] on the product. Press [ ] to move to SIZE&POSITION and press [ Press [ ] to move to Image Size and press [ ] on the product. ] on the product. The following screen will appear.
6 6.2 Resizing or Relocating the Screen H-Position Move the screen to the left or right. Available only when Size is set to Screen Fit. 6.2.1 Configuring H-Position 1 2 3 Press [ m ] on the product. Press [ ] to move to SIZE&POSITION and press [ Press [ ] to move to H-Position and press [ ] on the product. ] on the product. The following screen will appear. SIZE&POSITION Image Size H-Position 50 V-Position : 50 Menu H-Position : 50 Menu V-Position 10 Return 4 6.
6 Resizing or Relocating the Screen 3 Press [ ] to move to V-Position and press [ ] on the product. The following screen will appear. SIZE&POSITION Image Size Wide H-Position 50 V-Position 50 Menu H-Position 50 Menu V-Position 10 Return 4 6.4 Adjust the V-Position using the [ Adjust Enter ] button. Menu H-Position Move the menu position to the left or right. 6.4.1 Configuring Menu H-Position 1 2 3 Press [ m ] on the product.
6 Resizing or Relocating the Screen 6.5.1 Configuring Menu V-Position 1 2 3 Press [ m ] on the product. Press [ ] to move to SIZE&POSITION and press [ ] on the product. Press [ ] to move to Menu V-Position and press [ ] on the product. The following screen will appear. SIZE&POSITION Image Size Wide H-Position 50 V-Position 50 Menu H-Position 50 Menu V-Position 10 Return 4 Adjust the Menu V-Position using the [ Adjust Enter ] button.
7 7.1 Setup and Reset ECO Adjust the power consumption of the product to save energy. 7.1.1 Eco Motion Sensor The Eco Motion Sensor activates to save power when it does not detect any movement within a specified area for a specified period of time. Configuring the Eco Motion Sensor 1 2 3 4 Press [ m ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Eco Motion Sensor and press [ ] on the product. ] on the product.
7 Setup and Reset Configuring Backlight 1 2 3 4 Press [ m ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Backlight and press [ ] on the product. ] on the product. ] on the product. The following screen will appear.
7 Setup and Reset 4 Press [ ] to move to Eco Light Sensor and press [ ] on the product. The following screen will appear. ECO Eco Motion Sensor 5 Min Backlight 'LPPLQJ Eco Light Sensor Sensitivity Off On Brightness Level Eco Saving Off Eco Icon Display Off Return 5 6 Move Enter z Off z On: The Eco sensor detects the ambient illumination and automatically controls the brightness. Press [ ] to move to the option you want and press the [ ].
7 Setup and Reset 3 4 Press [ ] to move to ECO and press [ ] on the product. Press [ ] to move to Brightness Level and press [ ] on the product. The following screen will appear. ECO Eco Motion Sensor 5 Min Backlight Dimming Eco Light Sensor On Sensitivity High Brightness Level Eco Saving Eco Icon Display Return 5 6 Brighter Current ଥࢿ Dimmer Off Move Enter z Brighter : Increase the current brightness of the screen.
7 Setup and Reset 6 The selected option will be applied. 7.1.4 z This menu is not available when Bright is in Dynamic Contrast mode. z This menu is not available when Eco Light Sensor is enabled. Eco Icon Display Configuring the Eco Icon Display Settings 1 2 3 4 Press [ m ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to ECO and press [ Press [ ] to move to Eco Icon Display and press [ ] on the product. ] on the product. ] on the product.
7 Setup and Reset z When the screen becomes brighter as the ambient light becomes brighter and the Eco Light Sensor activates, the brightness slide bar level will increase with a sun image displayed above the bar. When the screen becomes darker, the brightness slide bar level will decrease with a moon image displayed above the bar. The brightness slide bar will be displayed for three seconds after the sensor activates.
7 Setup and Reset The progress of a tree growing will be represented as 10 different images (stages). After one z full-grown tree is complete, the initial image will be restored and the number of trees will continue to accumulate. The number for energy trees will be rounded to one decimal place. 7.2 Menu Transparency Set the transparency for the menu windows: 7.2.1 Changing Menu Transparency 1 2 3 Press [ m ] on the product. Press [ ] to move to SETUP&RESET and press [ ] on the product.
7 Setup and Reset 3 Press [ ] to move to Language and press [ ] on the product. The following screen will appear. SETUP&RESET ECO Menu Transparency Language PC/AV Mode Auto Source Display Time Key Repeat Time Return 4 5 7.4 Press [ 'HXWVFK (QJOLVK (VSDxRO )UDQoDLV ,WDOLDQR 0DJ\DU 3ROVNL 3RUWXJXrV ƧNJLjLjǁƿǀ 6YHQVND 7UNoH ᣣᧄ⺆ ଞ˲߭ ∝䇁 Move Enter ] to move to the option you want and press the [ ]. The selected option will be applied. PC/AV Mode Set PC/AV Mode to AV.
7 7.5 Setup and Reset Auto Source Activate Auto Source. 7.5.1 Configuring Auto Source 1 2 3 Press [ m ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Auto Source and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET ECO Off Language English PC/AV Mode PC Auto Source Display Time Auto Manual Key Repeat Time Acceleration Return 4 5 7.
7 Setup and Reset 3 Press [ ] to move to Display Time and press [ ] on the product. The following screen will appear. SETUP&RESET ECO Menu Transparency Off Language English PC/AV Mode PC Auto Source Display Time Key Repeat Time Return 4 5 7.7 Press [ 5 sec 10 sec 20 sec 200 sec Move Enter ] to move to the option you want and press the [ ]. The selected option will be applied. Key Repeat Time Control the response rate of a button when the button is pressed. 7.7.
7 7.8 Setup and Reset Customized Key By configuring Customized Key to suit your preferences, you can change the screen settings more conveniently. 7.8.1 Configuring Customized Key 1 2 3 Press [ m ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Customized Key and press [ ] on the product. ] on the product. The following screen will appear. SETUP&RESET Customized Key Off Timer On/Off Off Timer Setting 3D ECO MAGIC Imege Size Reset Return z 4 5 7.
7 Setup and Reset 3 Press [ ] to move to Off Timer On/Off and press [ ] on the product. The following screen will appear. SETUP&RESET Customized Key 3D Off Timer On/Off Off : On Off Timer Setting Reset Return 4 5 Move Enter z Off: Deactivate the off timer so that the product does not power off automatically. z On: Activate the off timer so that the product powers off automatically. Press [ ] to move to the option you want and press the [ ]. The selected option will be applied. 7.
7 Setup and Reset 7.11 Reset Return all the settings for the product to the default factory settings. 7.11.1 Initializing Settings (Reset) 1 2 3 Press [ m ] on the product. Press [ ] to move to SETUP&RESET and press [ Press [ ] to move to Reset and press [ ] on the product. ] on the product. The following screen will appear.
8 8.1 INFORMATION Menu and Others INFORMATION View the current input source, frequency and resolution. 8.1.1 Displaying INFORMATION 1 2 Press [ m ] on the product. Press [ ] to move to INFORMATION. The current input source, frequency and resolution will appear. PICTURE COLOR Digital SIZE&POSITION 67.5kHz 60Hz PP 1920 x 1080 SETUP&RESET INFORMATION Move Exit 8.
8 INFORMATION Menu and Others 1 Press [ ] in the startup screen. The following screen will appear. Volume Exit 2 Adjust the Volume using the [ 50 Adjust Enter ] button.
9 9.1 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center 9.1.1 Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check if your product is operating normally by using the product test function. If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC, perform a self-diagnosis test.
9 Troubleshooting Guide Screen issue "Not Optimum Mode" is displayed. This message appears if the signal from the graphics card exceeds the maximum resolution or frequency for the product. Change the maximum resolution and frequency to suit the product performance, referring to Standard Signal Mode Table (page 78). The images on the screen look distorted. Check the cable connection to the product (Refer to "3.3 Connecting and Using a PC") The screen is not clear. The screen is blurry.
9 Troubleshooting Guide Sound issue The volume is too low. Adjust the volume. If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program. Source device issue A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is booting, have your PC serviced.
9 9.2 Troubleshooting Guide Q&A Question How can I change the frequency? Answer Set the frequency on your graphics card. z Windows XP: Select Control Panel → Appearance and Themes → Display → Settings → Advanced → Monitor, and adjust Refresh rate under Monitor settings. z Windows ME/2000: Select Control Pane l → Display → Settings → Advanced → Monitor, and adjust Refresh rate under Monitor settings.
9 Troubleshooting Guide Question How can I change the resolution? Answer z Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings and adjust the resolution. z Windows ME/2000: Go to Control Panel → Display → Settings and adjust the resolution. z Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize → Display Settings and adjust the resolution.
10 Specifications 10.1 General Model Name LCD Panel Synchroni zation S23A950D S27A950D Size 23 inches (58cm) 27 inches (68cm) Display area 511.8 mm (H) x 288.3 mm (V) 599.6 mm(H) x 337.7 mm (V) 20.1 inches (H) x 11.4 inches (V) 23.6 inches (H) x 13.3 inches (V) Horizontal Frequency 30~140khz Vertical Frequency 50Hz, 100HZ, 120Hz Display Color 16.
10 Specifications This device is a Class B digital apparatus. [Recommendation] - EU Only z Hereby, Samsung Electronics, declares that this [Monitor] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. z The official Declaration of Conformity may be found at http://www.samsung.com, go to Support > Search Product Support and enter the model name. z This equipment may be operated in all EU countries.
10 Specifications 10.2 PowerSaver The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power-savign mode only functions when the product is connected to a PC with a power-saving function.
10 Specifications 10.3 Standard Signal Mode Table This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Therefore, a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for the screen size of your product.
10 Specifications HDMI Resolution 800 x 600 56 Hz 800 x 600 60 Hz 1024 x 768 60 Hz 1280 x 800 60 Hz 1280 x 960 60 Hz 1280 x 1024 60 Hz 1440 x 900 60 Hz 1680 x 1050 60 Hz 1920 x 1080 60 Hz 640 x 480 60 Hz, 480p 720 x 480 60 Hz, 480p 720 x 576 50 Hz, 576p 1280 x 720 50 Hz, 720p 1280 x 720 60 Hz, 720p 1920 x 1080 24 Hz, 1080i Horizontal Frequency(kH z) Vertical Frequency(Hz) Pixel Clock(MHz) Sync Polarity(H/V) 35.156 56.250 36.000 +/+ 37.879 60.317 40.000 +/+ 48.363 60.004 65.000 -/- 49.
10 Specifications Resolution Horizontal Frequency(kH z) Vertical Frequency(Hz) Pixel Clock(MHz) Sync Polarity(H/V) 56.250 50.000 148.500 +/+ 67.500 60.000 147.500 +/+ 1920 x 1080 50 Hz, 1080p 1920 x 1080 60 Hz, 1080p z Horizontal Frequency The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.
Appendix Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca (English) http://www.samsung.com/ca_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com LATIN AMERICA ARGENTINE 0800-333-3733 http://www.samsung.com BOLIVIA 800-10-7260 http://www.samsung.
Appendix LATIN AMERICA GUATEMALA 1-800-299-0013 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) HONDURAS 800-27919267 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) JAMAICA 1-800-234-7267 http://www.samsung.com NICARAGUA 00-1800-5077267 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) PANAMA 800-7267 http://www.samsung.com/latin (Spanish) http://www.samsung.
Appendix EUROPE CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com Samsung Electronics Czech and Slovak, s.r.o., Oasis Florenc, Sokolovská 394/17, 180 00, Praha 8 DENMARK 70 70 19 70 http://www.samsung.com EIRE 0818 717100 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com FINLAND 09 85635050 http://www.samsung.com FRANCE 01 48 63 00 00 http://www.samsung.com GERMANY 0180 5 SAMSUNG bzw. http://www.samsung.com 0180 5 7267864* (*0,14 €/Min. aus dem dt.
Appendix EUROPE SWEDEN 0771 726 7864 (SAMSUNG) http://www.samsung.com SWITZERLAND 0848-SAMSUNG (7267864, CHF 0.08/min) http://www.samsung.com/ch (German) http://www.samsung.com/ch_fr (French) U.K 0330 SAMSUNG (7267864) http://www.samsung.com CIS ARMENIA 0-800-05-555 http://www.samsung.com AZERBAIJAN 088-55-55-555 http://www.samsung.com BELARUS 810-800-500-55-500 http://www.samsung.com GEORGIA 0-800-555-555 http://www.samsung.com KAZAKHSTAN 8-10-800-500-55-500 (GSM: 7799) http://www.
Appendix ASIA PACIFIC INDIA http://www.samsung.com 1800 1100 11 3030 8282 1800 3000 8282 1800 266 8282 INDONESIA 0800-112-8888 021-5699-7777 http://www.samsung.com JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com NEW ZEALAND 0800 SAMSUNG (0800 726 786) http://www.samsung.com PHILIPPINES 1-800-10-SAMSUNG (726-7864) for PLDT http://www.samsung.
Appendix MIDDlE EAST MOROCCO 080 100 2255 http://www.samsung.com OMAN 800-SAMSUNG (726-7864) http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic) SAUDI ARABIA 9200-21230 http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic) TURKEY 444 77 11 http://www.samsung.com U.A.E 800-SAMSUNG (726-7864) http://www.samsung.com AFRICA ANGOLA 91-726-7864 http://www.samsung.com BOTSWANA 0800-726-000 http://www.samsung.com CAMEROON 7095- 0077 http://www.
Appendix Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
Appendix Terminology OSD(On Screen Display) On screen display (OSD) allows you to configure on-screen settings to optimize the picture quality as required. It allows you to change the screen brightness, tint, size and many other settings using menus displayed on the screen. Gamma The Gamma menu adjusts the grey scale that represents middle tones on the screen. Adjusting the brightness brightens the whole screen, but adjusting Gamma only brightens the medium brightness.
Appendix Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen. It represents the level of display detail. A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time. E.g. A resolution of 1920 x 1080 consists of 1,920 horizontal pixels (horizontal frequency) and 1,080 vertical lines (vertical resolution).
Index Numerics M 3D 26 MAGIC 40 A O Appendix 81 OSD control lock 22 Auto Source 63 P C PowerSaver 77 Checking the Resolution and Frequency 70 Precautions for storage 5 Cleaning 4 Configuring Tint 47 Connecting Headphones 39 Connecting to a PC 33 Connecting to a Video Device 39 R Removing the Packaging 19 Response Time 45 Reverse Side 23 Contact SAMSUNG WORLD WIDE 81 Copyright 2 Correct posture to use the product 13 Customized Key 65 S Safety Precautions 5 Securing the Installation Space 5 S
