Installation and Operating Instructions Ceramic Glass Hob CTR364T003 / CTR364N004 / CTR364D005 / CTR364E006 / CTR364T010 / CTR364N011 / CTR364D012 / CTR364E013 / C61RAAST / C61RABAL / C61RACN / C61RADST To avoid the risk of accidents or damage to the hob, read all instructions before installing or using the appliance. Keep this manual for future reference. CTR364T010_XSG-00129A-01_EN.
CTR364T010_XSG-00129A-01_EN.
Contents EN Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using This Manual EN Please take the time to read this owner’s manual, paying particular attention to the safety information contained in the following section, before using your appliance. Keep this manual for future reference. If transferring ownership of the appliance, please remember to pass the manual on to the new owner. The following symbols are used in the text This is the safety alert symbol. Warning indicates information concerning your personal safety.
Safety The safety aspects of this appliance comply with accepted technical standards and the German Appliance Safety Law. However, as manufacturers we also believe it is our responsibility to familiarise you with the following safety instructions. EN Electrical safety • Be sure the appliance is properly installed and grounded by a qualified technician. • The appliance should be serviced only by qualified service personnel.
Safety (continued) EN Safety during use • This appliance is to be used only for normal cooking and frying in the home. It is not designed for commercial or industrial use. • Never use the hob for heating the room. • Take care when plugging electrical appliances into mains sockets near the hob. Mains leads must not come into contact with the cooktop. • Overheated fat and oil can catch fire quickly. Never leave surface units unattended when preparing foods in fat or oil, for example, when cooking chips.
Installing the Hob Important: Be sure the new appliance is installed and grounded only by qualified personnel. Please observe this instruction. The warranty will not cover any damage that may occur as a result of improper installation. Technical data is provided at the end of this manual.
Installing the Hob (Continued) EN Connecting to the mains power supply Before connecting, check that the nominal voltage of the appliance, that is, the voltage stated on the rating plate, corresponds to the available supply voltage. The rating plate is located on the lower casing of the hob. Shut off power to circuit before connecting wires to circuit. The heating element voltage is AC230 V~. The appliance also works perfectly on older networks with AC220 V~.
Installing the Hob (Continued) Installing into the countertop EN Make a note of the serial number on the appliance rating plate prior to installation. This number will be required in the case of requests for service and is no longer accessible after installation, as it is on the original rating plate on the underside of the appliance. Pay special attention to the minimum space and clearance requirements.
Installing the Hob (Continued) EN 90 x4 2 = 490+1 100 100 = 8 CTR364T010_XSG-00129A-01_EN.
Parts and Features Cooking zones and control panel EN Single cooking zone 1800W Single cooking zone 1200 W 14 8 3 18 m 83 m m m 14 8 m m m m 1 Control panel Single cooking zone 1200 W Single cooking zone 1800W Indicators for heat settings and residual heat “Lock” control sensor Heat setting selectors “On/Off” control sensor 9 CTR364T010_XSG-00129A-01_EN.
Parts and Features (Continued) EN Components 1 Ceramic Glass Hob 2 Installation Brackets 3 Screws 10 CTR364T010_XSG-00129A-01_EN.
Parts and Features (Continued) The key features of your appliance EN • Ceramic glass cooking surface: The appliance has a ceramic glass cooking surface and four rapid - response cooking zones. The hob’s powerful radiant heater elements significantly shorten the amount of time required for the zones to heat up. • Touch control sensors: Your appliance is operated using touch control sensors.
Parts and Features (Continued) EN Safety shutoff If one of the cooking zones is not switched off or the heat setting is not adjusted after an extended period of time, that particular cooking zone will automatically switch itself off. Any residual warmth will be indicated with (for “hot”) in the digital displays corresponding to the particular cooking zones. The cooking zones switch themselves off at the following times.
Before You Begin Initial cleaning EN Wipe the ceramic glass surface with a damp cloth and ceramic cooktop glass cleaner. Important: Do not use caustic or abrasive cleaners. The surface could be damaged. Hob Use Using suitable cookware Better pans produce better results. • You can recognise good pans by their bases. The base should be as thick and flat as possible. • When buying new pans, pay particular attention to the diameter of the base. Manufacturers often give only the diameter of the upper rim.
Hob Use (Continued) EN • Always position pots and pans before switching on the cooking zone. • Dirty cooking zones and pan bases increase power consumption. • When possible, position the lids firmly on the pots and pans to cover completely. • Switch the cooking zones off before the end of the cooking time to use the residual heat for keeping foods warm or for thawing. • The base of the pan should be the same size as the cooking zone.
Hob Use (Continued) Switching the appliance on EN Touch the “Lock ” sensor for approximately 3 seconds. The appliance is switched on using the “On / Off ” control sensor. Touch the “On / Off ” sensor. The digital displays will show . After the “On / Off ” sensor has been actuated to switch on your appliance, a heat setting must be selected within approximately 10 seconds. Otherwise, the appliance will switch itself off for safety reasons.
Hob Use (Continued) EN Switching the appliance off To completely switch off the appliance, use the “On / Off Touch the “On / Off ” sensor. ” control sensor. After switching off a single cooking zone or the entire cooking surface, the presence of residual heat will be indicated in the digital displays of the corresponding cooking zones in the form of an (for “hot”).
Hob Use (Continued) Using the child safety lock EN You can use the child safety lock to safeguard against unintentionally turning on a cooking zone and activating the cooking surface. The lock control sensor can be used only when the power is on. Switching the child safety lock on 1. Touch the control sensor for approximately 3 seconds. An acoustic signal will sound as confirmation. approx . 3 sec . 2. Touch any heat setting control sensor .
Hob Use (Continued) EN Switching the child safety lock off 1. Touch the control sensor for approximately 3 seconds. An acoustic signal will sound as confirmation. approx . 3 sec . 18 CTR364T010_XSG-00129A-01_EN.
Hob Use (Continued) Locking and unlocking the control panel EN At any stage during the cooking process, the control panel, with the exception of the “On / Off ” control sensor, can be locked in order to prevent the settings from being changed unintentionally, for example, by wiping over the panel with a cloth. 1. Touch the lock control sensor for approximately 3 seconds. The indicator light in the lock control sensor will illuminate. The control sensors are now locked. 2.
Cleaning and Care EN Hob Important: Cleaning agents must not come into contact with a heated ceramic glass surface: All cleaning agents must be removed with adequate amounts of clean water after cleaning because they can have a caustic effect when the surface becomes hot. Do not use any aggressive cleaners such as grill or oven sprays, scouring pads or abrasive pan cleaners. Clean the ceramic glass surface after each use when it is still warm to the touch.
Cleaning and Care (Continued) Problem Dirt 1. Remove burnt-on sugar, melted plastic, aluminium foil or other materials with a glass scraper immediately and while still hot. EN I mportant: There is a risk of burning yourself when the glass scraper is used on a hot cooking zone: 2. Clean the hob as normal when it has cooled down. If the cooking zone on which something has melted has been allowed to cool, warm it up again for cleaning.
Warranty and Service EN FAQs and troubleshooting A fault may result from a minor error that you can correct yourself with the help of the following instructions. Do not attempt any further repairs if the following instructions do not help in each specific case. Warning: Repairs to the appliance are to be performed only by a qualified service technician. Improperly effected repairs may result in considerable risk to the user. If your appliance needs repair, please contact your customer service centre.
Warranty and Service (Continued) What does it mean when the burner does not glow red? • The selected temperature of the cooking zone is maintained by a sensor that cycles the zone on and off, so the surface cooking area will not always glow red. If you select a low heat setting, the heat will cycle on and off more frequently than at higher settings. The heat also cycles on and off at the highest setting.
Technical Data EN Appliance dimensions Width Depth Height 575 mm 505 mm 55 mm Worktop cut - out dimensions Width Depth Corner radius 560 mm 490 mm 3 mm Cooking rings Position Diameter Power Front left 183 mm 1,800 W Rear left 148 mm 1,200 W Rear right 183 mm 1,800 W Front right 148 mm 1,200 W Connection voltage Maximum connected load power Weight : Net 7.5 kg Gross 10.0 kg 230 V ~ 50 Hz 6.0 kW 24 CTR364T010_XSG-00129A-01_EN.
Note EN 25 CTR364T010_XSG-00129A-01_EN.
Code No.:DG68- 00129A-01 CTR364T010_XSG-00129A-01_EN.
