Install Manual 0
Install Manual ` Introduction Thank you for purchasing a Samsung SVR series digital video recorder. This manual is for SVR-3200, SVR-1680C, SVR-1660C, SVR-1645, SVR-960C, SVR-945, SVR-480. Before product installation and operation, please become thoroughly familiar with this user manual and other manuals referenced by this manual. This user manual and the software and hardware described here are protected by copyright law.
Install Manual After the expiration of the warranty period (3 years), examination and repair will be provided for a fee. Even during the warranty period, repair and examination of items outside the warranty scope will require payment. This product is not for exclusive use of crime prevention but for assistance in cases as fire or theft. We take no responsibility for damage from any incident.
Install Manual Contents Introduction ..................................................................................... 1 Product Warranty and Limits of Responsibility ............................................................ 1 Chapter 1. Safety Precautions ....................................................... 4 1.1 Explaining the Symbols ................................................................................. 4 Chapter 2. Summary ........................................................
Install Manual Chapter 1. Safety Precautions 1.1 Explaining the Symbols Warning Refers to information users need to know in order to prevent serious injury or death. Before installation 9 Verify the supplied voltage (AC100V~AC240V) before connecting to the power supply. 9 Make sure the power supply is off before installation. 9 Do not install in a very humid environment. Doing so may cause an electric shock or fire. 9 Make sure ground line is connected to reduce electric shock risk.
Install Manual Dismantling and cleaning 9 Do not dismantle, repair or modify the product deliberately. Doing so may cause a damage, an electric shock or an injury. 9 Do not use water, paint thinner or organic solvent for cleaning the product exterior. Doing so may cause a malfunction or an electric shock. Use a dry cloth to clean the exterior. Caution Provides information users need to know in order to prevent minor injury or product damage.
Install Manual Samsung Techwin cares for the environment at all product manufacturing stages, and is taking a number of steps to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s will to create environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
Install Manual Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment. To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system. The rechargeable battery incorporated in this product is not user replaceable. For information on its replacement, please contact your service provider.
Install Manual Chapter 2. Summary This unit is a digital video recording and playback device to record image and video input from 32/16/9 channels to its built-in hard disk. The buttons on the front of the unit as well as the mouse and GUI allow easy setup and operation. The Samsung SVR series of digital video recorders (DVRs) provide additional safety and security to banks, apartment buildings and complexes, government offices as well as other public, private and commercial facilities.
Install Manual Audio Recording SVR series DVRs provide real time audio recording.
Install Manual Each channel supports pre-emptive recording sequences up to 5 seconds prior to an actual event Search/Playback Various search and playback options are offered for the user’s convenience.
Install Manual Networking The product supports LAN, xDSL and other networking capabilities. Combined with the PC interface client, the core features of the device can be easily remotely controlled.
Install Manual 2.1 Components Please check the included accessories as follows. AC CORD Remote Controller Program CD SATA Cable HDD Mount Screw Install Manual DVR Quickguide SNM-128S Quickguide Rackmount & Screw For the SVR-945, a switched-mode power supply (SMPS) power cord is included, while a stand is included instead of the standard rack mount. SVR-480 does not include rack mount & Screw.
Install Manual 2.2 Description of product 2.2.1 Front view 2.2.1.1 No. 1 2 SVR-3200 Classification Function DVD-Multi for For copying recorded video and images to DVD/CD copying optical media. Channel LED Shows the data input and event operation status Jog can adjust setting values, control the STEP function, 3 JOG/SHUTTLE navigate through the menu, and adjust the playback speed and direction. Shuttle controls PTZ.
Install Manual PLAY lamp Lit when copying. 11 Power button Turns on or off the device. 12 ESC button The Escape button navigates up the menu tree and closes dialog windows. 13 COPY Starts Copy mode. 14 FUNC Starts Function mode. 15 MONITOR Cycles through from Monitor 1 to 4. 16 PTZ Starts or ends PTZ function. 17 USB1, USB2 USB ports for external devices (mouse, USB memory stick). 18 PLAY/ENTER Start playback or select an item on the menu.
Install Manual 2.2.1.2 No. 1 2 SVR-1680C, SVR-1660C, SVR-1645 Classification Function DVD-Multi for For copying recorded video and images to DVD/CD copying optical media. Channel LED Shows the data input and event operation status Jog can adjust setting values, control the STEP function, 3 JOG/SHUTTLE navigate through the menu, and adjust the playback speed and direction. Shuttle controls PTZ.
Install Manual closes dialog windows. 13 COPY Starts Copy mode. 14 FUNC Starts Function mode. 15 MONITOR Cycles through from Monitor 1 to 4 : SVR-1680C, Switches from main and sub monitor : SVR-1660C, SVR-1645 16 17 PTZ USB1, USB2 Starts or ends PTZ function. USB ports for external devices (mouse, USB memory stick). 18 PLAY/ENTER Start playback or select an item on the menu. 19 ◀/REW Navigates or selects in the menu, or for playback, changes the reverse playback speed.
Install Manual 2.2.1.3 No. 1 SVR-960C Classification DVD-Multi Function for For copying recorded video and images to DVD/CD copying optical media. 2 Channel LED Shows the data input and event operation status 3 Channel button Selects channel in live feed or playback 4 AUTO Starts or stops user defined sequences. 5 MULTI Changes split-screen sections for live video feeds or playback. 6 MENU Navigates into the Menu. 7 SEARCH Starts Search mode.
Install Manual 14 MONITOR Switches from main and sub monitor 15 PTZ Starts or ends PTZ function. 16 USB1, USB2 USB ports for external devices (mouse, USB memory stick). 17 PLAY/ENTER Start playback or select an item on the menu. 18 ◀/REW Navigates or selects in the menu, or for playback, changes the reverse playback speed. 19 ▶/FWD Navigates or selects in the menu, or for playback, changes the forward playback speed.
Install Manual 2.2.1.4 No. SVR-945 Classification Function 1 Channel LED Shows the data input and event operation status 2 Channel button Selects channel in live feed or playback 3 AUTO Starts or stops user defined sequences. 4 MULTI Changes split-screen sections for live video feeds or playback. 5 MENU Navigates into the Menu. 6 SEARCH Starts Search mode. 7 REC button Starts or stops manual recording REC lamp Lit when recording. HDD lamp Lit when HDD is working.
Install Manual 14 15 PTZ USB1, USB2 Starts or ends PTZ function. USB ports for external devices (mouse, USB memory stick). 16 PLAY/ENTER Start playback or select an item on the menu. 17 ◀/REW Navigates or selects in the menu, or for playback, changes the reverse playback speed. 18 ▶/FWD Navigates or selects in the menu, or for playback, changes the forward playback speed. 19 ▲/PAUSE Navigates or selects in the menu, or for playback, pauses live or recorded video.
Install Manual 2.2.1.5 No 1 SVR-480 Classification DVD-Multi Function for For copying recorded video and images to DVD/CD optical copying media. 2 Channel button Selects channel in live feed or playback 3 Channel LED Shows the data input and event operation status 4 AUTO Starts or stops user defined sequences. 5 MULTI Changes split-screen sections for live video feeds or playback. 6 MENU Navigates into the Menu. 7 SEARCH Starts Search mode.
Install Manual dialog windows. 13 COPY Starts Copy mode. 14 FUNC Starts Function mode. 15 MONITOR Switches from main and sub monitor 16 PTZ Starts or ends PTZ function. 17 PLAY/ENTER Start playback or select an item on the menu. 18 ◀/REW Navigates or selects in the menu, or for playback, changes the reverse playback speed. 19 ▶/FWD Navigates or selects in the menu, or for playback, changes the forward playback speed.
Install Manual 2.2.2 Rear Part 2.2.2.1 No. SVR-3200 Input/Output Function terminal name 1 POWER IN Socket for AC 100V ~ AC 240V power cord. 2 CH1 ~ 32 Connection terminal for camera BNC input. 3 MONITOR 1 ~ 4 Connection terminal for monitor BNC output. 4 AUDIO IN(RCA) RCA audio jack for RCA input. 5 AUDIO OUT Audio jack for speaker output. 6 GROUND Ground terminal between DVR and external device. 7 ETHERNET Ethernet port for network connections (RJ-45).
Install Manual 15 SENSOR IN Connection terminal for sensor input. 16 AUDIO IN(D-SUB) Connection terminal for audio output D-SUB. 17 D-I/O Connection terminal for DIGITAL IN/OUT.
Install Manual 2.2.2.2 No. SVR-1680C, SVR-1660C, SVR-1645 Input/Output Function terminal name 1 POWER IN Socket for AC 100V ~ AC 240V power cord. 2 CH1~16 Connection terminal for camera BNC input. 3 LOOP OUT Connection terminal for camera BNC output (loop). 4 MONITOR 1 ~ 2 Connection terminal for monitor BNC output. 5 AUDIO IN(RCA) RCA audio jack for RCA input. 6 AUDIO OUT Audio jack for speaker output. 7 GROUND Ground terminal between DVR and external device.
Install Manual 2.2.2.3 No. SVR-960C Input/Output Function terminal name 1 POWER IN Socket for AC 100V ~ AC 240V power cord. 2 GROUND Ground terminal between DVR and external device. 3 CH1~9 Connection terminal for camera BNC input. 4 LOOP OUT Connection terminal for camera BNC output (loop). 5 MONITOR 1 ~ 2 Connection terminal for monitor BNC output. 6 AUDIO IN(RCA) RCA audio jack for RCA input. 7 AUDIO OUT Audio jack for speaker output.
Install Manual 2.2.2.4 No. SVR-945 Input/Output Function terminal name 1 CH1~9 Connection terminal for camera BNC input. 2 LOOP OUT Connection terminal for camera BNC output (loop). 3 MONITOR 1 ~ 2 Connection terminal for monitor BNC output. 4 AUDIO IN(RCA) RCA audio jack for RCA input. 5 AUDIO OUT Audio jack for speaker output. 6 ETHERNET Ethernet port for network connections (RJ-45). 7 eSATA Connection terminal for external eSATA HDD or HDD for backups.
Install Manual 2.2.2.5 SVR-480 No. Input/Output Function terminal name 1 GROUND Ground terminal between DVR and external device. 2 CH1~4 Connection terminal for camera BNC input. 3 LOOP OUT Connection terminal for camera BNC output (loop). 4 MONITOR 1 ~ 2 Connection terminal for monitor BNC output. 5 AUDIO IN(RCA) RCA audio jack for RCA input. 6 AUDIO OUT Audio jack for speaker output. 7 ETHERNET Ethernet port for network connections (RJ-45).
Install Manual 2.2.3 Remote control All DVR unit features can be controlled with the remote controller; 16 units can be controlled with a single remote controller. Unit IDs should be set in the DVR Menu > Communication > Remote > Remocon ID. No. Classification Function 1 ID Selects ID. 2 FUNC Starts function mode. 3 MULTI Changes split-screen sections for live video or playback. 4 STATUS Displays system setup information. 5 MON Changes screen to spot monitor.
Install Manual No. 18 Classification (◀) Function Moves cursor left in setup menu. 19 (▶) Moves cursor right in setup menu. 20 (▲) Moves cursor up in setup menu. 21 (▼) Moves cursor down in setup menu. 22 ENTER Saves settings and execute. 23 ESC Cancels settings or navigates up in menu. 24 SEARCH( ) Displays the search menu. 25 FAST Fast reverses playback. REWIND(◀◀) 26 REWIND Reverses playback. PLAY(◀) 27 FORWARD Forwards playback. PLAY(▶) 28 FAST Fast forwards playback.
Install Manual Chapter 3. Installation 3.1 Installation & Connection 3.1.1 Basic connection and operation 3.1.1.1 Camera connection Connect the DVR and CCTV cameras using coaxial cable as in the following figure. - The cameras’ video input type must be one and only of NTSC or PAL. Both types should not be used together.
Install Manual 3.1.1.3 Audio connection Audio equipment connects to the DVR unit using RCA audio cables or D-SUB as shown in the following figure. SVR-480 does not support D-SUB audio. Refer to the following figure when connecting D-SUB. The audio inputs are pin numbers 5 ~ 16. 3.1.1.4 Power connection & operation Connect the power cable as shown in the following figure. - The DVR unit will boot automatically when the power is connected.
Install Manual 3.2 OSD Menu structure & Operation 3.2.1 Menu structure Press the [MENU] button on the front panel to change to setup mode and display the following dialog. Main menu Sub menu Setup dialog box (1) Main menu: The currently selected tab is highlighted in blue with submenus and options displayed below. Use the cursor [◀/▶] keys to navigate between submenu items then press [Enter] to activate it. (2) Sub menu: The currently selected submenu name is displayed in the title bar.
Install Manual 3.2.1.1 Character input dialog box The characters input dialog lets you input text. Character input Use the cursor [▲/▼] and [◀/▶] keys to choose characters then press [Enter] to input it. Use [Å] to backspace, and [Æ] to insert a space. When finished, press [Enter] to exit the character input dialog with the newly inputted value. 3.2.2 Remote control setup & basic operation 3.2.2.
Install Manual Remote Control ID supports a maximum of 16 IDs. For unused remote controllers, set Remote Control ID to Off. 3.2.2.2 Selecting IDs All DVR unit features can be controlled with the remote controller; 16 units can be controlled with a single remote controller. Unit IDs should be set. 1) Check the remote controller ID in DVR Menu. 2) Press the ID button on the remote controller. 3) Press the number button on the remote controller.
Install Manual 3.2.3 Example of installation structure 3.2.3.1 Basic connection diagram Connect the cameras, monitors and audio. 3.2.3.2 Extended connection diagram Connect the cameras, monitors, audio, sensors, relays and other peripherals. 3.2.3.3 External storage and backup connection diagram Connect a USB memory device or a “Samsung SVS-5E external HDD (eSATA)” unit.
Install Manual 3.2.3.4 Internet/Intranet connection diagram 3.2.4 Basic setup 3.2.4.1 Video check The product automatically powers on when the power cord is plugged in. Once it finishes booting up, the default 16 channel split-screen is displayed. If a password for the unit has been set, the password input dialog is displayed. Only the numeric buttons work here and all others are temporarily disabled until the correct password is entered. (The factory default has no password protection.) 3.2.4.
Install Manual Time Zone (1) Press [◀/▶] or [▲/▼] to select “Time Zone”, and then press [Enter]. (2) Press [◀/▶] to set the correct Time Zone, and then press [ESC]. Daylight Saving (1) When selecting a Daylight Saving Time zone, Daylight Saving automatically changes to On, and is Off for other time zones. (2) To customize the start and end time of DST, use the [◀/▶] buttons and change Daylight Saving to Custom. (3) Changing Daylight Saving to Custom displays the Custom DST Setup options.
Install Manual The second is for selecting a month, week, and day to define the start and end times of DST. Date Format (1) Press [◀/▶] or [▲/▼] to select “Date Format”, and then press [Enter]. Press [◀/▶] to select a date format: YYYY/MM/DD, MM/DD/YYYY, or DD/MM/YYYY. (2) Press [ESC] to exit edit mode. Time (1) Press [◀/▶] or [▲/▼] to select “Time”, and then press [Enter]. (2) Press [◀/▶] to individually select “Date” and “Time”. Press [▲/▼] to set the proper values for each.
Install Manual (1) Press [◀/▶] or [▲/▼] to select “Apply Date / Time” and then press [Enter]. A confirmation dialog is displayed as shown below. (2) Press [◀/▶] or [▲/▼] to select “YES” and then press [Enter]. Press [ESC] to cancel the new date/time and return to the original value from before. 3.2.4.3 Record setup Press [Menu] and select “Quick Setup” when the OSD menu appears. Program setup This menu allows user to set resolution, frame rates, and quality for each channel individually.
Install Manual Schedule Setup Select the “Schedule & Event” option, and set the Day & Time options. How to check the record status If the record setup is configured correctly, [REC LED] on the front panel will light up RED. Also, record status [S] will be displayed on the video screen. [S] indicates scheduled recording. 3.3 Using input/output terminals 3.3.1 Handling cable ends The following details how to handle cables for the terminal block.
Install Manual - Stranded wire: Strip 8 ~ 10㎜ of insulation off the end of the wire and solder it together. Use AWG 22 ~ 26 wire. - Solid wire: Strip 8 ~ 10㎜ of insulation off the end of the wire. Use AWG 20 ~ 26. 3.3.2 Wire insertion/removal When inserting/removing wires to/from the terminal block, push the driver as shown below and insert or remove the wire. 3.3.3 Sensor connections & settings 3.3.3.1 Specification The sensor specifications are as follows. Specification Electric capacity No.
Install Manual Sensor input terminal connection Connect sensors to S1 ~ S16 as illustrated in the figure below. Please note that the figure shows connecting sensors with dry contacts. Refer to the section on handling wiring for more information about connecting or disconnecting sensor wires. Sensor Settings (1) Press [Menu] and select “Event” when the OSD menu appears. (2) Press [Enter] or [▼] to enter the submenu, select “Sensor” and press [Enter].
Install Manual Individual sensor This option allows setting each of the 16 sensor input types individually. (1) Select a sensor then press [Enter]. (2) Set the input type for the selected sensor. (3) Press [ESC] to exit to the OSD menu when you are finished. Sensor setup lets you choose whether or not to use sensors and their type, and Record & Relay setup, while set separately, should be set according to the sensor type.
Install Manual Relay out connection Connect relays to R1 ~ R16 as illustrated in the figure below. The example shows how to connect a warning light. Refer to the section on handling wiring for more information about connecting or disconnecting relay wires. Relay Out Settings Relays can be triggered by following events; alarm sensor, motion detection, video loss, hard disk fail, hard disk full, fan fail, password fail, and DDNS registration failure.
Install Manual as Relay out, the Output can be operated with digital I/O. Also, if Input is operated, the emergency recording is started. Then the emergency recording starts to record with the Event Record value. Specification The D-I/O specifications are as follows. Specification Rated current No. of inputs/outputs 12 Output type DC 3V output Connection method Connect stripped wire end with 15 pin D_SUB. DC 3.
Install Manual For more information, refer to the user manual. The user manual can be downloaded from www.samsungcctv.com or on the CD provided with the product. 3.3.3.4 Serial communication terminal connections & settings Serial communication terminal connection for Pan/Tilt/Zoom PTZ cameras for the DVR unit can be connected through the COM port, and supported models configured through the OSD menu.
Install Manual Serial Comm.
Install Manual COM3 connection diagram (RS-232) PTZ, Keyboard Compatible List Model Manufacturer SDZ160/330, Samsung SPD SAMSUNG TECHWIN Keyboard SCC3000, Samsung SRX-100B BOSCH AutoDome, TC8560X-4 BOSCH PELCO(P), PELCO(D) PELCO Honeywell 755/655, HRX-2000, ScanDome2 HONEYWELL Sony EVI-D3x SONY VT VPT-4x VT AD SpeedDome AD SungJin SJ372R1’ SUNGJIN Samsung SCC641 SAMSUNG ELECTRONICS Panasonic WV-CS850 PANASONIC LG GAC-PT2 LG Keyboard KBD300A, WGI SPD1800/2600 WEBGATE Inc.
Install Manual Tokina TOKINA Kodicom KRE KODICOM Nuvico NUVICO Serial Settings A total of four serial ports are available for the DVR. Two are RS-232C(Com1, Com3) and the other two are RS-422/485(Com2, Com4). The Serial Port settings are available under Communication > Remote. The following options are provided for the Serial Port settings. PTZ(Serial) Select PTZ. To control the PTZ operation via serial port, select PTZ in the Device options, and then set up a serial port.
Install Manual Type Select a serial port. Protocol Select a connected PTZ device. Camera ID Enter the ID of the selected camera. Interface Select one from among Com2 to 4. To use RS-232, select Com3. For RS-422 or 485, select Com2 or 4. Baud rate/Parity/Stop Bit/Data Bit Enter the same settings as the ones for the PTZ device. Idle Time Activate or disable PTZ Home, and set up a standby duration for the device before moving to PTZ home.
Install Manual Type Select Coax. Protocol Select Pelco or Pelco Extended according to the coax protocol type of Pelco camera. AD Dome does not support menu control, Presets or AUX when setup with a coax protocol. Idle Time Activate or disable PTZ Home, and setup a standby duration of the device before moving to PTZ home. 3.3.3.
Install Manual Serial Settings (COM1) (1) In the OSD menu, navigate to Communication > Serial. (2) Set the “Serial Number” option to COM1 for text. (3) Set the Baud Rate/Parity/Stop bit/Data bit options identical to the Input device. Text Settings (1) On the OSD menu, select Event Setup > Text. (2) Set text and relations options. Some external devices may not be recognized. Please consult your product distributor prior to installation. 3.3.3.
Install Manual Supported USB devices conform to the following specifications. USB Spec. Ver. 2.0 Supported device USB memory stick types Output Max. 200mA per DC 5V / Port voltage/current The storage device should be formatted with the FAT32 file system. Supported storage devices are automatically recognized when copying. To copy video, set copying options in the Copy dialog, select the storage device, then copy the data. [CD/DVD Copy] [RE4 Copy] Select the channel to copy.
Install Manual [AVI Copy] Some USB storage devices may require additional software and drivers. Care should be taken in these cases as the DVR may not recognize some USB products like this. If copied files do not playback on another computer, double check that proper playback software and codecs are installed. 3.3.3.7 Video in/out connections The DVR video input/output are “Loop through" and detect connection status automatically to set terminal resistance.
Install Manual 3.3.3.8 Audio in/out connections There are 4 RCA audio in and 12 D-SUB audio in. All 16 audio sources can be monitored through a single output. The 12 D-SUB audio inputs use terminals 5 ~ 16 and are connected as shown in the following figure. 3.3.4 3.3.4.1 External Storage connections eSATA Port One eSATA external storage device can be connected through the eSATA port in the back of the DVR unit for a maximum of 8TB of storage space.
Install Manual 1. Turn DVR power OFF. 2. Connect external device and eSATA interface cable. 3. Turn external device power ON. 4. Turn DVR Power ON. 3.3.4.3 Supported HDD Refer to the appendix in the back of the manual for information on supported HDDs. 3.3.4.4 Registering & formatting HDDs When the DVR is first booted after a new HDD is physically installed, the "Disk Manager" automatically runs as shown in the following figure.
Install Manual Once the HDD is attached with the screws, insert it into an HDD bracket. For the location of HDDs, IntA is the bottom right, IntB is the upper right, IntC is the bottom left, and IntD is the upper left. The following picture shows an HDD being inserted to IntA. When attaching an HDD, first insert the front part of the HDD to the bracket, and then press down on the other side with the SATA port. Once the HDD is inserted, connect the SATA and power cables.
Install Manual After inserting the HDD, fasten the HDD fixture bracket as shown in the picture below. Now the HDD is fully attached to the product.
Install Manual To enable the newly attached HDD, you must change the availability of the HDD to "Yes" under the DVR Disk menu. To access the menu, go to Menu > System Settings > Disk > Disk Manager. The newly attached HDD will display in the HDD list with No in the Availability pane. To change the availability, place the cursor on No and then press Enter. When a dialog window appears, select "Yes." Now the HDD is ready to use.
Install Manual Detaching HDD Detaching an HDD is the same as attaching it, but in reverse order. Loosen the HDD fixture bracket. Unplug the SATA and power cables. Detach the HDD. When detaching an HDD, first lift up the back part of the HDD with the SATA port, and then the front part. Remove or keep the HDD fixture screws in case you want to attach an HDD later.
Install Manual Go to Menu > System Settings > Disk > Disk Manager. Select the detached HDD, and the press Enter. Select "Yes" in the dialog window and remove the HDD from the HDD list.
Install Manual 3.3.5 Remote monitoring & control Connections can be made through Internet/Intranet by using the remote computer. This connection can be used to control DVRs and monitor areas same as local spot. 3.3.5.1 Ethernet connection (1) Shut the DVR power off. (2) Connect the Ethernet cable to the DVR and hub or router. (3) Turn the DVR power on. To prevent damage to the DVR, turn the power on after connecting the Ethernet cable. The Ethernet cable should be securely connected.
Install Manual When using Ethernet Set the type to Ethernet and fill in the IP address, Netmask, Gateway, and DNS information provided by your network administrator. Use Up/Down direction keys or the mouse wheel to select the items, and then setup with the appropriate values. When using PPPoE Change the network configuration type to xDSL then navigate to the xDSL menu. Change the port from Ethernet. (IMPORTANT: You must remember the port.
Install Manual Trouble Shooting 1. DVR does not boot z Check power z Check power cord 2. Monitor does not display camera video z Check monitor power z Check cable between the monitor and DVR z Check monitor cable port z Check that DVR power is on 3. Some channels do not display images z Check camera power z Check camera video input z Check DVR video input port z Check whether the Screen > Activity option is on/off z Check the Monitor > Covert option for privacy settings 4.
Install Manual 8. Front buttons do not work z Check DVR power z Check screen lock status 9. Cannot connect to network z Check that network cable is properly connected z Check DVR IP address z Check PC IP address z Run a ping test 10. When to contact your reseller If any of the following happen, immediately turn of the DVR and contact the reseller that you purchased it from. z The product exhibits extremely abnormal behavior, e.g.
Install Manual Compatible HDD List Western Digital Capacity Model 1000GB WD10EVCS 750GB WD7500AVCS 500GB WD5000AVVS 320GB WD3200AVVS Compatible Media List DVD-R manufacture CD-R manufacture Mitsubishi (16X) Mitsubishi (16X) TDK (16X) TDK (16X) Imation (16X) Imation (16X) Sony (16X) Sony (16X) Specification Item Description Display SVR-3200 : 32 composite video 0.5–2 Vpp, 75 ohm automatic termination SVR-1680C/1660C/1645 : 16 composite video 0.
Install Manual Performance Recording Compression Record Rate/NTSC MPEG-4 SVR-3200 : 480fps@704x480, 960Cfps@704x240, 960Cfps@352x240 SVR-1680C : 480fps@704x480, 480fps@704x240, 480fps@352 x 240 SVR-1660C/1645 : 120fps@704x480, 240fps@704x240, 480fps@352x240 SVR-960C/945 : 120fps@704x480, 240fps@704x240, 270fps@352x240 SVR-480 : 120fps@704x480, 120fps@704x240, 120fps@352x240 SVR-3200 : 400fps@704x576, 800fps@704x288, 800fps@352x288 SVR-1680C : 400fps@704x576, 400fps@704x288, Record Rate/PAL 400fps@352x2
Install Manual Protocol support Monitoring Storage Maximum Capacity Internal HDD External HDD and NTP CMS Software(SNM-128S/P), Built-in web server SVR-3200/1680C/1660C : 16 TB SVR-1645/960C/945/480 : 8 TB SVR-3200/1680C/1660C : 4 HDD SVR-1645/960C/945/480 : 2 HDD SVR-3200/1680C/1660C : External eSATA 2 port SVR-1645/960C/945/480 : External eSATA 1 port DVD Writer (Back-up) DVD-R / CD-R USB (Back-up) 2 External USB Ports(USB 2.
Install Manual Outputs Connections Screw terminal 4 relay outputs, NO/NC (SVR-480 : Screw terminal 2 relay outputs, NO/NC) Remote notification Notification via e-mail Ethernet RJ45 10/100 Base-T Serial interface RS232 SVR-3200/1680C/1660C : RS485/RS422 PTZ control interface SVR-1645/960C/945/480 : RS485 Via coax cable (SVR-1680C/1660C/960C) PTZ Keyboard RS485, max. signal voltage ±12 V USB 2 USB 2.
Install Manual Dimensions SVR-3200, SVR-1680C, SVR-1660C, SVR-1645 71
Install Manual SVR-960C 72
Install Manual SVR-945 73
Install Manual SVR-480 74
Install Manual This product uses some Software programs which are distributed under the GNU GPL(General Public License)/LGPL license, and the program is licensed as is without warranty of any kind. , The program can be obtained from us for a period of three years after our last distribution of this product by sending email to help.cctv@samsung.com.
Install Manual Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents.
Install Manual charge to all third parties under the terms of this License.
Install Manual such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable.
Install Manual could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
Install Manual AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12.
Install Manual An "Application" is any work that makes use of an interface provided by the Library, but which is not otherwise based on the Library. Defining a subclass of a class defined by the Library is deemed a mode of using an interface provided by the Library. A "Combined Work" is a work produced by combining or linking an Application with the Library. The particular version of the Library with which the Combined Work was made is also called the "Linked Version".
Install Manual The object code form of an Application may incorporate material from a header file that is part of the Library.
Install Manual 1) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (a) uses at run time a copy of the Library already present on the user's computer system, and (b) will operate properly with a modified version of the Library that is interface-compatible with the Linked Version.
Install Manual Each version is given a distinguishing version number. If the Library as you received it specifies that a certain numbered version of the GNU Lesser General Public License "or any later version" applies to it, you have the option of following the terms and conditions either of that published version or of any later version published by the Free Software Foundation.
Install Manual 85
Install Manual 86
