Assembling the cleaner Product accessories Carton contents Empty carton. Find the parts shown above before disposing of packing materials. Vacuum Cleaner user manual English imagine the possibilities Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at www.samsung.
Safety information SAFETY INFORMATION • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Because the following operating instructions cover various models, the WARNING characteristics of your vacuum cleaner may differ slightly from those described in this manual. WARNING CAUTION/WARNING SYMBOLS USED WARNING CAUTION Indicates that a danger of death or serious injury exists. Indicates that a risk of personal injury or material damage exists.
Safety information IMpORTANT SAFETY INSTRucTIONS Thank you for purchasing a Samsung vacuum cleaner. When using an electrical appliance, basic precautions should always be followed, including the following : PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. WARNING : To reduce the risk of fire, electric shock, or injury. • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Do not leave vacuum cleaner unattended when it is plugged in.
Contents assembling the cleaner 05 operating the cleaner 09 How to operate 11 14 Maintain tools and filter Trouble shooting 20 4_ Contents 05. Introduction 06. Product accessories 07. Assembling the cleaner 08. Tool storage 09. Cord release 09. Power foot height adjustment 10. Power switch/Power foot brush roll switch 10. Circuit break (Reset switch) 11. How to operate 12. Using accessories 13. Longreach cleaning 14. Check rotating floor brush and drive belt 14. Replace drive belt 15.
Assembling the cleaner INTROducTION Cord clip Hose Carrying handle (Dust bin handle) Extension pipe wand Dusting brush holder Hanger cord Dust bin Hose guide Crevice tool holder Height adjustment knob Power foot (Brush roll) Smart inverter Handle release Furniture guard FRONT CAUTION WARNING BACK Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures. Plastic film can be dangerous.
Assembling the cleaner Product accessories Carton contents Ⓐ Ⓑ Ⓒ Ⓓ Empty carton. Find the parts shown above before disposing of packing materials. A. Vacuum cleaner body B. Handle C. Hose D. Extension Pipe wand Accessories Ⓔ Ⓕ The accessories are packed on the cleaner. E. Crevice tool F. Mini turbo brush G.
Assembling the cleaner 1 3 01 ASSEMblINg ThE clEANER 2 4 5 1 Slide fully retracted extension wand into the handle until you hear a click. 2 Slide fully retracted wand and handle into the slot on body until you hear a click. Makes sure slot guides and inserts. 3 Slide fully retracted hose into the handle until you hear a click. 4 Put hose into hose guide down the back of the vacuum cleaner. 5 Slide fully connected hose with the inverter.
Assembling the cleaner TOOl STORAgE Attach tools. Clip turbo tool into the caddy on the front of the handle. Attach dusting tool into the dusting tool holder on side of the body. Attach crevice tool into the crevice tool holder on side of the body. Mini turbo brush (Turbine brush) • Use for upholstered furniture, carpeted stairs and hard to reach places.
Operating the cleaner cORd RElEASE Turn cord release 180 degrees for easy cord removal. Store cord wraps to keep out of the way while vacuuming. 02 OpERATINg ThE clEANER Cord release Up pOwER FOOT hEIghT AdjuSTMENT The power foot on your SAMSUNG vacuum cleaner can be adjusted to clean several floor surfaces. For optimal cleaning performance, adjust to the lowest practical setting. If your cleaner is difficult to push, adjust to the next higher setting. 1. Place handle in upright position 2.
Operating the cleaner Power switch/Power foot brush roll switch Dust bin release Power ON/OFF Power control Pipe release Brush roll on/off The Power on/off button is located on the top body. Turn on vacuum by power button after plugging cord into electrical outlet. The vacuum is automatically controled by the dirt senser. The dirt sensor is automatic power control by dust amount. There are 3 suction power levels by power control button.
How to operate 03 hOw TO OpERATE Plug cord into electrical outlet. Press power on/off button. Push cleaner handle release down with foot and pull handle towards you. Handle release pedal is located on the lower left side you look at the back of the vacuum cleaner. Handle Positions Select the desired angle of the cleaner using the handle release pedal. The handle of your cleaner has three positions. Raise or lower the handle and release the pedal. A.
How to operate uSINg AccESSORIES Put the cleaner in the upright position to stop the brush-roll rotating, or simply press the brush-roll on/off button. Push down and pull out the handle, while pressing the pipe release button. Remove the hose and handle from the slot. The air flow is automatically inverted by the smart inverter. Choose any of the handy accessories or use the hose alone. Simply push the attachment firmly into the end of the extension wand. To remove tool, twist and pull apart gently.
Longreach cleaning 03 hOw TO OpERATE The stretch hose is extended for long reach and upstairs. Do not put the your Vacuum cleaner above you on the stairs when cleaning the stairs. Ensure it is positioned against up the bottom stairs.
Maintain tools and filter Check Rotating Floor Brush and Drive Belt You should check your vacuum cleaner’s rotating floor brush and drive belt regularly for wear or damage. You should also clean the brush and brush ends of strings, hair, and carpet fibers. These can wrap around the brush and hamper its ability to effectively clean your carpet. Also remove any debris that has accumulated under the brush cover. 1. Unplug cleaner from electrical outlet. 2.
Smart Inverter Silde inverter Hose inverter Maintain tools and filter _ 15 04 MAINTAIN TOOlS ANd FIlTER 1. Unplug cleaner from electrical outlet. 2. Remove 3 screws at back of the vacuum cleaner show with a screwdriver. 3. Clean up the smart inverter inside. 4. Refit hose inverter (Check the position carefully) 5. Refit smart inverter and 3 screws.(When refit the smart inverter while slide inverter pushing down) 6. Slide fully connected hose with the inverter(Check the position carefully) 7.
Maintain tools and filter Carton contents Brushbar Replacement 1. Remove the tool from the pipe, and turn upside down. Slide the switch to unlock position and remove bottom plate. 2. Remove brushbar and discard. 3. Inspect belt to ensure that it is in good condition. If broken or cracked, please replace. (See below for details.) 4. With the curved ends facing down, slide end plates of brushbar into slots on the tool. 5.
EMpTYINg ThE duST bIN To remove dust bin from vacuum cleaner, push the dust bin release button. Hold dust bin and push down bin release empty button to empty. Turn grille cyclone for easy dust removal. Ensure bin is empty and close dust bin base. Maintain tools and filter _ 17 04 MAINTAIN TOOlS ANd FIlTER When emptying any vacuum cleaner it is difficult to avoid exposure to dust.
Maintain tools and filter Cleaning the dust bin & Re-assembling the dust bin Push down cyclone release button. Turn grille cyclone for clean. Cleaning the clean bin. Rinse with cold water only. Ensure dust bin and grille is completely dry before refitting Fit cyclone assembly inside the bin Line up the front and rear guides and push down secure. Push down bin release empty button and refit the grille cyclone Close dust bin base. 1 2 3 4 5 6 7 8 Check the assembling dust bin base and body grille.
wAShINg YOuR FIlTER For safety, Turn power off and unplug before checking for blockages. Cover filter Sponge filter Micro filter Case filter The HEPA filter should be replaced every 6 months. Inse r t This Direction Inse r Inse rt This Direction t ThTihse HD EPAif rection ilter s months. Check the assembling order when Re-assembling the filter. The HEPA filter sh hould be replaced every 6 .
Trouble shooting Check this list of possible problems and solutions before bring your vacuum to a service center Problem Possible solution Vacuum cleaner won’t turn on • Not properly plugged into electrical outlet. • Vacuum cleaner not turned on. • No electricity in the electrical outlet.