for use by qualified installers, !f yOU aie ha2ing prob!ems instai!ing this dishWashe, Please ca!l : 1 _800,SAMSUNG (726,7864) for assistance : www.samsung.com the possibilities Thank you for purchasing this Samsung product. To recewe more complete service. please register your product at www.samsung.
Throughout this manual, you'll see Warning and Caution notes, These warnings, cautions, and the important sCety instructions that follow do not cover all possible conditions and situations that may occur, It's your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher, Samsung is not liable for damages resulting from improper use, IMPORTANT SAFETY INSTRUCTIONS What the icons and signs in this installation guide mean: WARNING Hazards or unsafe
GROUNDING INSTRUCTIONS For a permanently connected appliance: This appliance must be connected to grounded metal, a permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two or more people are needed to move a dishwasher and avoid potential injuries.
oont nt PREPARING INSTALLING THE DISHWASHER ENCLOSURE 5 Product dimensions 5 Cutout dimensions THE DISHWASHER 6 8 STEP 1 STEP 2 Checking the parts and tools Selecting the best location for the dishwasher 9 10 Water supply requirements Electrical requirements 11 12 STEP 3 STEP 4 STEP 5 STEP 6 13 14 15 17 STEP STEP STEP STEP 18 STEP 11 SPECIFICATIONS / 4 contents 7 8 9 10 Preparing the dishwasher Placing the dishwasher and connecting water supply line Leveling the dishwasher Securing th
d p p rncj PRODUCT Side view (DMR78 series/ DMR77 series) DIMENSIONS 27" (686 mm) ,4 Rear view (DMR78 series DMR77 Series/ DMR57 Series) _ .... _" 20 _/2"(520 mm) 24 _/2"(622 mm) Side view (DMR57 series) i The water supply 24 *A" (629 mm) i and drain hose line, power cable should go through this part. 24 _/2' (622 mm) CUTOUT [_ DIMENSIONS This dishwasher is designed to be enclosed on top and on both sides by a standard residential kitchen unit.
Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you're not at risk of injury when washing dishes. STEP 1 CHECKING THE PARTS AND TOOLS Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. This will save installation time and simplify the installation process.
Tools required Electric drill Safe ty glasseS Gloves Adjustable wrench Wire stripper Pliers Tape measure Tubing cutter Pencil Cutting Flashlight Nipper Phillips screwdriver knife Hole cutter Flat screwdriver Level installing the dishwasher 7
[_ ew installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, the connections for the dishwasher being replaced must be checked for compatibility with the new dishwasher and replaced as necessary. STEP 2 SELECTING THE BEST LOCATION FOR THE DISHWASHER The following criteria are important to ensure the best location for the dishwasher. 1.
STEP 3 WATER SUPPLY REQUIREMENTS 1. The dishwasher can be connected to either the hot or the cold water supply. If the temperature of the water supplied to the dishwasher is below 149 °F (65 °C), connect it to the hot water supply. If it is higher than 149 °F (65 °C), connect it to the cold water supply. 2. Ensure that the water supply valve is turned off before connecting the water supply line to the dishwasher. 3.
STEP 4 ELECTRICAL REQUIREMENTS The electrical requirements for the dishwasher are as follows: • In the United States, in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, in accordance with the Canadian Electric Code C22.1-1atest edition/Provincial and Municipal codes and/or local codes. The dishwasher must be connected with the correct rated voltage supply marked on the rating plate of the unit. 2.
STEP 5 PREPARING THE DISHWASHER 1. Ensure that the circuit breaker and water supply valve are turned off before proceeding with the following steps. 2. Ensure that the kick plate is placed on the cushion front, and make sure to keep it. 3. Install the 90" elbow at the Inlet valve. When inserting the elbow into the Inlet valve, use Teflon tape or sealing compound to prevent water leakage. To prevent blocking the inlet valve, make sure that the Teflon tape or sealing compound does not enter the valve. 4.
STEP 6 PLACING THE DISHWASHER SUPPLY LINE AND CONNECTING WATER 1. Adjust the four leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (Refer to the figures in STEP 7.) 2. Locate the water supply line for connecting the inlet valve on the left and the power cable for connecting the junction box on the right. 3.
STEP 7 LEVELING THE DISHWASHER 1. Open the door and place the level against the top of the tub from inside and check whether the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level. 2. Check whether the dishwasher is upright (perpendicular), as shown in the figure to the right. 3. Open the door of the dishwasher and check whether both the tub and door clearances are correct.
STEP 8 SECURING THE DISHWASHER The dishwasher should be fixed to the countertop or side walls for additional stability and safety. 1. When the countertop is made of wood or the material will not be damaged by drilling, follow the instructions in 2-1 below. When the countertop is made of granite, marble or any other kind of material that can be damaged by drilling, follow the instructions in 2-2 below. 2-1. Check to connect the Installation brackets to the front top of the dishwasher as shown in Figure 8.
STEP 9 CONNECTING THE DRAIN HOSE 1. Check the parts on the sink to which the drain hose is connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures. Connecting the drain outlet must be done in accordance with the water pipe installation regulations in your region. Case 1. Without disposal f hose Hose'clamp Case 2.
3. Check the size of the sink's drain hose connector. If needed, cut the drain hose so its end fits into the sink connector (1/2 in., 3/4 in. or 1 in. - as shown in the Figure below). If the end of the drain hose does not fit into the drain hose connector of the sink, use an adaptor purchasable at a plumbing/hardware supply store. 4. When connecting the drain hose, make sure to fasten it using a hose clamp. Failing to do so may cause water leakage. 5.
STEP 10 WIRING CONNECTIONS 1. Before connecting the power cable to the dishwasher, make sure to turn off the circuit breaker. 2. Check to remove the junction box cover located at the bottom right at the front of the dishwasher. You will find three power wires from the dishwasher including the grounding line. 3. Connect the power cable to the dishwasher. Twist and connect each wire using wire connectors. When using wire connectors, insert each wire as shown in Figure 14 and rotate the wire connector.
I Power supply 120 V, 60 Hz AC only Water pressure 20 - 120 psi (140 - 830 kPa) Dimensions (WidthxDepthxHeight) 237/8x 243Ax 337/8in. (605 x 627 x 860 mm) Nominal 120 °F (49 °C) [_ inlet water temperature Specifications are subject to change without notice for quality improvement purposes. The actual appearance of the dishwasher may differ from the illustrations in this manual.
QUESTIONS OR COMMENTS? USA 1-800-SAMSUNG (726-7864) www.samsung.com CANADA 1-800-SAMSUNG (726-7864) www.samsung.com/ca/ Code No.
