DV330AE* DV340AE* Gas and Electric Dryer user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register DV340AE-02820B-03_EN.
features 1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra large 7.3 cu.ft. capacity dryer circulates more air through your clothes, drying them faster for a wrinkle-free result. 2. Sanitize course This course allows you to sanitize garments by permeating high temperature heat deep into the fabric during the drying cycle. Use this course to keep your bedding and curtains clean. When selecting this cycle, 99.
safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WARNING - Risk of Fire • • • • Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer’s instructions and local codes.
safety instructions WARNING WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3.
WHAT TO DO IF YOU SMELL GAS: • • • • • • Do not try to light any appliance. Do not turn on the appliance. Do not touch any electrical switch. Do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
safety instructions The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance. Do not sit on top of the dryer. Because of continuing product improvements, Samsung reserves the right to change specifications without notice.
contents INSTALLING YOUR DRYER 8 8 9 11 11 11 12 12 13 14 14 15 16 16 19 20 21 Tools needed for installation See Dryer Exterior Ducting requirements Important to installer Location considerations Alcove or closet installation Mobile home installation Exhausting Gas requirements Electrical requirements Grounding Electrical connections Replacement parts and accessories Installation Final installation checklist Dryer Exhaust Tips Door Reversal OPERATING INSTRUCTIONS, TIPS 22 25 25 25 26 27 27 27 Overview
installing your dryer TOOLS NEEDED FOR INSTALLATION Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup, adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer, you are responsible. Make sure you have everything necessary for proper installation. 1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. 2. A POWER CORD for electric dryers (except Canada). 3.
DUCTING REQUIREMENTS • • • • • • • • • • • • • • • • • • 01 installing your dryer • Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation. Lint accumulation should be cleaned regularly. If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall.
installing your dryer If the new dryer is installed into an existing exhaust system you must make sure: • The exhaust system meets all local, state, and national codes. • That a flexible plastic duct is not used. • To Inspect and clean all lint buildup from inside the existing duct. • The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
IMPORTANT TO INSTALLER Please read the following instructions carefully before installing the dryer. These instructions should be kept for future reference. REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD SUFFOCATING. LOCATION CONSIDERATIONS The dryer should be located where there is enough space at the front for loading the dryer, and enough space behind for the exhaust system. This dryer is factory-ready for rear exhaust.
installing your dryer MOBILE HOME INSTALLATION The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made. Locate an area that has adequate fresh air.
GAS REQUIREMENTS • • 01 installing your dryer Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas.
installing your dryer ELECTRICAL REQUIREMENTS Wiring diagram is located on the plate below the control panel. • WARNING • • Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require 120/208 volt, 60 Hz approved electrical service.
installing your dryer REPLACEMENT PARTS AND ACCESSORIES If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG(726-7864). INSTALLATION Gather the required tools and parts before starting the installation. Read and follow the instructions provided with any tools listed here.
U.S. MODELS: IMPORTANT – All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If the 4-wire system is used, the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.
installing your dryer 6. Review Gas Requirements section. Remove the pipe thread protective cap. Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections. Pipe joint compound must be resistant to the action of any liquefied petroleum gas. Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4” (1.9 cm) female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer.
4-WIRE system connections 01 installing your dryer 1. Remove the center terminal block screw. 2. Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw. 3. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block. 4. Connect the other wires to the outer terminal block screws. Tighten screws. 5. Tighten the strain relief screws. 6.
installing your dryer DRYER EXHAUST TIPS Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 1. Make sure your dryer is installed properly so it exhausts air easily. 2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually.
DOOR REVERSAL 7. Reinsert the screw in the other hole. 4. Remove a screw on the Frame Front. 9. Reinsert the screw (Step 4) on the Frame Front. 5. Remove the two screws on the opposite side of the door hinge. 10. Place the door on the other side and reattach it to the dryer. 6. Remove two screws from the holder lever. 11. Reattach the holder lever. 7. Remove a screw from the door hinge. 12. Reattach the screws in the remaining holes. 01 installing your dryer 1. Unplug the power cord. 2.
operating Instructions, tips OVERVIEW OF THE CONTROL PANEL 1 1 Cycle Selector 2 3 4 5 6 7 8 9 To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate. The Normal, Heavy Duty, Towels, Perm Press, Delicates and Sanitize cycles are Sensor Dry cycles. Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level (more dry to damp dry) is reached.
Dry Level Selection Button To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles, press the Dry Level button. An indicator light will illuminate next to the desired dryness level. Press the button repeatedly to scroll through the settings. Larger or bulkier loads may require the More Dry setting for complete dryness. The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle.
operating Instructions, tips 7 Select Cycle Option Mixed Load Bell - This is an alarm that notifies the user when the average dry level is damp dry (80% dried). This is useful when the laundry contains various types of clothing you do not want to dry completely. An alarm sounds for five (5) seconds while continuing to perform the cycle. This function can only be selected in the Sensor Dry course, and the dry level can only be selected from among Normal Dry, More Dry.
CHILD LOCK A function to prevent children from playing with your dryer. Setting/Releasing How to Set: 1. It can be set while your dryer is running. 2. Once you set the Child Lock function, no button, except for the Power button, will respond until you release the Child Lock function. 3. The Child Lock indicator will be lit. 1. If the dryer is powered on again, the Child Lock function stays on. 2. To release that function, follow the instructions above.
operating Instructions, tips RACK DRY Installing the drying rack 1. Open the dryer door. 2. Position the drying rack in the tumbler, placing the front lip of the drying rack on the top of the lint filter. 3. Place the rear legs in the two recessed areas of the dryer’s back wall, then push down the middle of the drying rack to fix. 4. Place the items to be dried on the rack, leaving space between them so air can circulate. 5. Close the dryer door. 6. Use the Time Dry cycle.
CLEAN THE LINT FILTER • • • After each load. To shorten drying time. To operate more energy efficiently. 03 operating Instructions, tips Cleaning the Lint filter 1. Pull the case-filter out of the dryer. 2. Scrape the dust from the top part of the filter using your fingers. 3. Open the bottom cover and scrape the dust in the same way. 4. Shake off the dust, close the cover and install it in its place. CAUTION When you re-insert the Filter-Case Filter, check the direction it is installed in.
care and cleaning CONTROL PANEL Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel. The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your dryer and wipe up any spills or overspray immediately. TUMBLER Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an allpurpose cleaner.
special laundry tips SPECIAL LAUNDRY TIPS Bedspreads & Comforters • • • Blankets • • Curtains & Draperies • • Follow the care label instructions or dry on the Normal cycle and High temperature. Make sure the item is thoroughly dry before using or storing. May require repositioning to ensure even drying. Use Normal cycle and dry only one blanket at a time for best tumbling action. Make sure the item is thoroughly dry before using or storing.
troubleshooting CHECK THESE POINTS IF YOUR DRYER… PROBLEM SOLUTION Doesn’t run. • • • • Make sure the door is latched shut. Be sure the power cord is plugged into a live electrical outlet. Check the home’s circuit breaker and fuses. Press the Start/Pause button again if the door is opened during the cycle. Doesn’t heat. • • • • • Check the home’s circuit breaker and fuses. Select a heat setting other than Air Fluff. On a gas dryer, check that the gas supply is on.
PROBLEM SOLUTION Shuts off before load is dry • • • • • • Garments still wrinkled after • Wrinkle-Release • Odors remain in clothing after Refresh. • Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.
troubleshooting INFORMATION CODES Information codes may be displayed to help you better understand what is occurring with your Dryer. ERROR DISPLAY MEANING SOLUTION Clogged Lint Screen Vent is restricted Clean the screen or vent. If the problem continues call for service. do dE Running the dryer with door open Close the door and then restart. If the problem continues call for service. dF Door is not closing properly Call for service.
appendix FABRIC CARE CHART Wash Cycle Special Instructions Warning Symbols for Laundering Normal Line Dry/ Hang to Dry Do Not Wash Permanent Press / Wrinkle Resistant / Wrinkle Control Drip Dry Do Not Wring Gentle/Delicates Dry Flat Do Not Bleach Hand Wash Heat Setting Do Not Tumble Dry High No Steam (added to iron) Hot Medium Do Not Iron Warm Low Cold Any Heat Dry Clean No Heat/Air Do Not Dry Clean Water Temperature** Bleach Any Bleach (when needed) Iron-Dry or Steam Temperatu
appendix PROTECTING THE ENVIRONMENT This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. DECLARATION OF CONFORMITY This appliance complies with UL2158.
CYCLE CHART Default Cycle Manual Dry Cooling Wrinkle prevent Time Temp control Sensor dry level Time Time Time Normal High (Medium) Normal dry 42 min 39 min 3 min Heavy Duty High (No change) Normal dry 58 min 55 min 3 min Perm Press Medium (No change) Normal dry 32 min 29 min 3 min Delicates Low (No change) Normal dry 27 min 24 min 3 min Sanitize High (No change) More dry 60 min 55 min 5 min Timed Dry High - 40 min 37 min 3 min Quick Dry High (No change) - 30
warranty SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
QUESTIONS OR COMMENTS? Country CALL OR VISIT US ONLINE AT CANADA 1-800-SAMSUNG(726-7864) www.samsung.com Code No. DC68-02820B-03_EN DV340AE-02820B-03_EN.
DV330AE* DV340AE* Sèche-linge à gaz et électrique Manuel d’utilisation Un monde de possibilités Nous vous remercions d’avoir choisi un produit Samsung. Afin de bénéficier d’un service plus complet, veuillez enregistrer votre produit à l’adresse www.samsung.com/register DV340AE-02820B-03_CFR.
caractéristiques 1. Très grande capacité La très grande capacité de séchage est désormais accessible à tous ! Vous pouvez désormais faire sécher d’importants volumes de linge en une seule fois. D’une capacité plus qu’exceptionnelle de 7.3 cu.ft. (207 litres), ce sèche-linge fait circuler plus d’air à travers vos vêtements les séchant plus vite et en réduisant le froissement. 2.
consignes de sécurité Félicitations pour l’achat de votre nouveau sèche-linge Samsung. Ce manuel contient de précieuses informations sur l’installation, l’utilisation et l’entretien de votre appareil. Prenez le temps de le lire pour tirer pleinement profit de tous les avantages et de toutes les fonctionnalités de votre sèche-linge. AVERTISSEMENT - Risque d’incendie • • • • L’installation du sèche-linge doit être effectuée par un technicien qualifié.
consignes de sécurité AVERTISSEMENT AVERTISSEMENT: afin de réduire les risques d’incendie, d’électrocution ou de blessures lors de l’utilisation de l’appareil, respectez les règles de sécurité de base suivantes : 1. Lisez toutes les consignes de sécurité avant d’utiliser l’appareil. 2.
QUE FAIRE EN CAS D’EMANATION DE GAZ : • • • • • • Ne tentez pas d’allumer un appareil électrique. Ne mettez pas l’appareil sous tension. Ne touchez à aucun interrupteur électrique. N’utilisez aucun téléphone dans le bâtiment. Faites évacuer tous les occupants de la pièce, du bâtiment ou du secteur. Appelez immédiatement votre fournisseur de gaz depuis le téléphone d’un voisin. Suivez les consignes que vous recevrez. • Si vous ne pouvez pas joindre votre fournisseur de gaz, appelez les pompiers.
consignes de sécurité Cet appareil doit être correctement mis à la terre. Ne branchez jamais le cordon d’alimentation sur une prise qui n’est pas correctement reliée à la terre et qui n’est pas conforme aux réglementations locales et nationales en vigueur. Consultez les instructions d’installation pour relier cet appareil à la terre. Ne vous asseyez pas sur le sèche-linge. Dans le cadre de l’amélioration constante de ses produits, Samsung se réserve le droit de modifier les spécifications sans préavis.
contenu INSTALLATION DU SÈCHE-LINGE 8 8 Outils requis pour l’installation 8 Extérieur du sèche-linge 9 Conditions requises en matière de conduits 11 Remarque importante pour l’installateur 11 Choix de l’emplacement d’installation 11 Encastrement dans une niche ou installation dans un placard 12 Installation en mobile home 12 Evacuation 13 Systèmes fonctionnant au gaz 14 Normes électriques 14 Mise à la terre 15 Raccordement électrique 16 Pièces de rechange et accessoires 16 Installation 19 Liste de contrôl
installation du sèche-linge OUTILS REQUIS POUR L’INSTALLATION Laissez un professionnel installer correctement votre sèche-linge. Si vous contactez le service aprèsvente suite à une installation, des réglages ou un branchement mal exécutés, la responsabilité relève de l’installateur. Si c’est vous qui avez installé le sèche-linge, la responsabilité vous incombe. Vérifiez que vous disposez de tous les éléments requis pour installer correctement l’appareil, comme suit. 1.
CONDITIONS REQUISES EN MATIÈRE DE CONDUITS • • • • • • • • • • • • • • • • • • 01 installation du sèche-linge • Utilisez un conduit en aluminium ou en acier galvanisé rigide d’un diamètre de 4”(10,2 cm). N’utilisez pas de conduit plus petit. Les conduits dont le diamètre est supérieur à 4”(10,2 cm) peuvent provoquer une trop grande accumulation de peluches. Vous devez retirer régulièrement les peluches accumulées.
installation du sèche-linge SECHE-LINGE ELECTRIQUE ET A GAZ Type de hotte d’évacuation * Recommandé A n’utiliser que pour les installations temporaires 4”(10,16 cm) 2,5”(6,35 cm) Nbre de coudes à 90 ° Rigide Métallique flexible* Rigide Métallique flexible* 0 24,4 m 12,4 m 22,6 m 10,1 m 1 20,7 m 11,2 m 18,9 m 8,8 m 2 17,4 m 10,1 m 15,5 m 7,6 m 3 14,3m 9m 12,5 m 6,5 m N’utilisez pas de conduits flexibles non métalliques.
REMARQUE IMPORTANTE POUR L’INSTALLATEUR Lisez attentivement les instructions suivantes avant d’installer le sèche-linge. Conservez soigneusement ces instructions pour référence ultérieure. RETIREZ LE HUBLOT DES APPAREILS MIS AU REBUT POUR EVITER QU’UN ENFANT NE S’ETOUFFE. CHOIX DE L’EMPLACEMENT D’INSTALLATION Le sèche-linge doit être installé dans un endroit suffisamment spacieux, tant à l’avant pour permettre de charger l’appareil, qu’à l’arrière pour le système d’évacuation.
installation du sèche-linge INSTALLATION EN MOBILE HOME Toute installation du sèche-linge dans un mobile home doit se faire conformément à la réglementation sur les normes de sécurité et de construction de bien manufacturé, titre 24 CFR, partie 3280-80 (anciennement norme fédérale sur la sécurité et la construction de mobile home, titre 24, HUD (partie 280), 1975) pour les Etats-Unis ou la norme CSA Standards Z240 pour le Canada.
SYSTÈMES FONCTIONNANT AU GAZ • • 01 installation du sèche-linge Utilisez uniquement du gaz naturel ou du propane liquide (PL). L’INSTALLATION DOIT ETRE CONFORME AUX REGLEMENTATIONS LOCALES EN VIGUEUR OU, EN L’ABSENCE DE DISPOSITIONS SPECIFIQUES, A LA REGLEMENTATION NATIONALE SUR LE GAZ COMBUSTIBLE ANSI/Z223.1 (NATIONAL FUEL GAS CODE), DERNIERE REVISION (POUR LES ETATS-UNIS) OU AUX DISPOSITIONS D’INSTALLATION CAN/CGA-B149 (POUR LE CANADA).
installation du sèche-linge NORMES ÉLECTRIQUES Le schéma de câblage est sur une plaque située sous le panneau de commande. • AVERTISSEMENT • • Un branchement incorrect du conducteur de mise à la terre peut représenter un risque de surtension électrique. Demandez conseil à un électricien ou un réparateur agréé si vous avez des doutes quant à la mise à la terre de l’appareil. Ne modifiez pas la prise fournie avec le sèche-linge.
RACCORDEMENT ÉLECTRIQUE Modèles au gaz : États-Unis et Canada Vous devez utiliser une alimentation électrique de 120 volts c.a., 60 Hz et un disjoncteur ou fusible de 15 A. Modèles électriques : États-Unis uniquement Aux Etats-Unis, la plupart des sèche-linge requièrent une alimentation en 120/240 volts c.a., 60 Hz, tandis que d’autres requièrent une alimentation en 120/208 volts, 60 Hz. Vous trouverez les spécifications électriques sur l’étiquette située derrière le hublot.
installation du sèche-linge PIÈCES DE RECHANGE ET ACCESSOIRES Si vous avez besoin de pièces de rechange ou d’accessoires pour votre sèche-linge, contactez votre revendeur ou le centre d’assistance clientèle de SAMSUNG au 1-800-SAMSUNG (726-7864). INSTALLATION Regroupez et vérifiez les pièces et outils requis avant de commencer l’installation. Lisez et respectez les instructions fournies avec les outils répertoriés ici.
MODELES POUR LES ETATS-UNIS : IMPORTANT : tous les modèles destinés aux Etat-Unis sont conçus pour un BRANCHEMENT 3 FILS. Le châssis du sèche-linge est relié à la terre par un conducteur neutre au niveau du bornier. Un BRANCHEMENT A 4 FILS est requis dans les cas suivants : nouvelles constructions, habitations rénovées, mobile homes, réglementations locales n’autorisant pas la mise à la terre via le conducteur neutre.
installation du sèche-linge 6. Consultez la section Systèmes fonctionnant au gaz. Retirez le capuchon de protection du filet au pas du gaz. Appliquez sur tous les raccords filetés un matériau de joint d’étanchéité pour canalisation ou une bande de Teflon sur 1 tour 1/2. Le matériau de joint d’étanchéité utilisé doit être résistant à l’action des gaz de pétrole liquéfié. Branchez l’alimentation en gaz sur votre sèche-linge.
Branchements à 4 FILS 01 installation du sèche-linge 1. Retirez la vis centrale du bornier. 2. Reliez le fil de terre (vert ou sans habillage) du cordon d’alimentation au conducteur à vis de terre externe. 3. Branchez le fil neutre (blanc ou central) du cordon d’alimentation et le fil de terre de l’appareil (vert à rayures jaunes) sous la vis centrale du bornier. 4. Reliez les autres fils aux bornes à vis extérieures. Serrez les vis. 5. Serrez les vis de décharge de tension. 6.
installation du sèche-linge CONSEILS POUR L’ÉVACUATION DU SÈCHE-LINGE Les conduits en plastique ou non métalliques représentent un danger potentiel d’incendie. AVERTISSEMENT 1. Assurez-vous que le sèche-linge a été installé de manière à ce que l’évacuation de l’air se fasse sans problème. 2. Utilisez un conduit d’évacuation métallique rigide de 4”(10,2 cm). Scellez tous les joints à l’aide d’un ruban en aluminium, y compris au niveau du sèche-linge.
INVERSION DU HUBLOT 7. Ré-engagez la vis dans l’autre trou. 4. Retirez une vis de l’avant du cadre. 9. Ré-engagez la vis (étape 4) à l’avant du cadre. 5. Retirez les deux vis sur le côté opposé de la charnière du hublot. 10. Placez le hublot de l’autre côté et refixez-le sur le sèche-linge. 6. Retirez les deux vis du dispositif de fermeture. 11. Remontez le dispositif de fermeture. 7. Retirez une vis de la charnière du hublot. 12. Ré-engagez les vis dans les trous restants.
instructions et conseils d’utilisation PRÉSENTATION DU PANNEAU DE COMMANDE 1 1 Sélecteur de programme 2 3 4 5 6 7 8 9 Cour choisir un cycle, positionnez le sélecteur sur le programme de votre choix. Un voyant s’allume à côté du programme choisi. Normal(Normal), Heavy Duty(Grand Rendement), Serviettes, Perm Press(Perm Press), Delicates(Délicats) et Sanitize(Stérilisation)sont des cycles fonctionnant avec capteur de séchage.
2 Bouton Dry Level (Niveau de séchage) 4 Bouton Temp. (Température) 5 Bouton Time (Temps) 6 Bouton Signal (Signal) 7 Options de programme 02 instructions et conseils d’utilisation 3 Affichage numérique La fenêtre d’affichage montre la durée estimée restante du programme une fois que vous avez appuyé sur le bouton Start/Pause (Démarrer/Pause). Cette durée estimée peut varier à mesure que le programme avance. Le voyant Séchage s’allume et reste allumé jusqu’à la fin du programme.
instructions et conseils d’utilisation 8 9 Bouton Start/ Pause (Démarrer/ Pause) Appuyez sur ce bouton pour interrompre et relancer les programmes. Bouton Power (Mise en marche) Appuyez une fois sur ce bouton pour mettre le sèche-linge en marche. Réappuyez dessus pour l’éteindre. Si le sèche-linge reste allumé pendant plus de 10 minutes sans qu’aucun bouton ne soit actionné, il s’éteint automatiquement. SÉCURITÉ ENFANT Cette fonction empêche les enfants de jouer avec le sèche-linge.
SÉCHAGE ÉTENDOIR Installation du support de séchage ARTICLES 02 instructions et conseils d’utilisation 1. Ouvrez le hublot du sèche-linge. 2. Placez la grille de séchage dans le tambour, en positionnant son bord avant sur le dessus du filtre à peluches. 3. Insérez les deux pieds arrière dans les orifices situés sur la paroi arrière du sèche-linge, puis appuyez sur le centre de la grille pour la fixer. 4.
instructions et conseils d’utilisation NETTOYAGE DU FILTRE À PELUCHES • • • Après chaque séchage. Pour réduire la durée de séchage. Pour un meilleur rendement énergétique. Nettoyage du filtre à peluches 1. Retirez le boîtier du filtre du sèche-linge. 2. Grattez la poussière située sur la partie supérieure du filtre à l’aide de vos doigts. 3. Ouvrez le capot inféreur et faites tomber la poussière en procédant de la même façon. 4. Refermez le capot et remettez le boîtier en place.
CHARGEMENT DU SÈCHE-LINGE • • • MISE EN MARCHE 1. 2. 3. 4. 5. 6. Chargez votre sèche-linge sans tasser le linge. Surtout, NE LE SURCHARGEZ PAS. Fermez le hublot. Sélectionnez le programme et les options appropriés en fonction de la charge de linge (voir pages 20 et 21). Appuyez sur le bouton Start/Pause (Démarrer/Pause). Le voyant du sèche-linge s’allume. Une estimation de la durée du programme apparaît sur l’écran.
entretien et nettoyage PANNEAU DE COMMANDE nettoyez-le avec un chiffon doux et humide. N’utilisez pas de produits abrasifs. Ne vaporisez aucun produit d’entretien directement sur le panneau de commande. Certains détachants pour tissu peuvent endommager le revêtement du panneau de commande. Appliquez donc ces produits à l’écart de votre sèche-linge et essuyez immédiatement toute éclaboussure ou vaporisation en excès.
conseils d’entretien du linge CONSEILS D’ENTRETIEN DU LINGE Couvre-lits et couettes • • • Couvertures • • Rideaux et tentures • • Observez les symboles de l’étiquette ou sélectionnez le programme de séchage Normal et la température Élevé Vérifiez que l’article est complètement sec avant de l’utiliser ou de le ranger. Il est parfois nécessaire de repositionner l’article dans le sèche-linge pour assurer un séchage homogène.
dépannage VÉRIFIEZ LES POINTS SUIVANTS SI VOTRE SÈCHE-LINGE... PROBLÈME SOLUTION Ne se met pas en route. • • • • Ne chauffe pas. • • • • • Ne sèche pas. • • • • • • • • • Fait du bruit. • • • • Assurez-vous que le hublot est bien fermé. Vérifiez que le cordon d’alimentation est branché sur une prise électrique opérationnelle. Vérifiez le disjoncteur et les fusibles de votre domicile. Appuyez de nouveau sur le bouton Démarrage/Pause en cas d’ouverture du hublot en cours de programme.
PROBLÈME SOLUTION Ne sèche pas le linge uniformément. • Dégage une odeur. • • S’arrête avant que le linge ne soit sec. • • Les vêtements sont pelucheux. • • • • Les vêtements sont • encore froissés après • le programme WrinkleRelesase(Sans froissement). Les vêtements gardent une odeur après le programme Refresh. • 05 dépannage • Les coutures, les poches et les autres zones épaisses peuvent ne pas sécher complètement alors que le reste du linge a atteint le niveau de séchage sélectionné.
dépannage CODES D’ERREUR Des codes système s’affichent parfois pour vous permettre de mieux comprendre le problème rencontré par le sèche-linge. AFFICHAGE DE L’ERREUR SIGNIFICATION SOLUTION Filtre à peluches bouché Capacités du système d’aération réduites Nettoyez le filtre ou le système d’aération. Si le problème persiste, appelez le service de dépannage. do dE Faire fonctionner le sèche-linge lorsque le hublot est ouvert Fermez le hublot, puis redémarrez.
annexe TABLEAU DES SYMBOLES TEXTILES Lavage Instructions spéciales Symboles de nettoyage Normale Séchage en suspension Ne pas laver Infroissable / Antifroissage Séchage sans essorage Ne pas tordre Délicat Séchage à plat Pas d’agent de blanchiment Lavage à la main Séchage Pas de séchage machine Élevée Pas de vapeur Hot Moyenne Pas de repassage Tiède Faible Froid Toutes températures Nettoyage à sec autorisé Pas de séchage Pas de nettoyage à sec Température de l’eau** Agent de blan
annexe PROTECTION DE L’ENVIRONNEMENT Cet appareil a été fabriqué à partir de matériaux recyclables. Si vous décidez de le jeter, veuillez respecter les normes locales en matière d’évacuation des déchets. Coupez le cordon d’alimentation de façon à ce que l’appareil ne puisse pas être raccordé à une source électrique. Enlevez le hublot pour que des animaux et des jeunes enfants ne se retrouvent pas piégés à l’intérieur de l’appareil. DÉCLARATION DE CONFORMITÉ Cet appareil est conforme à la norme UL2158.
TABLEAU DES PROGRAMMES Valeur par défaut Séchage à capteur Programme mimuté Refroidissement Prévention du froissement Temps Température Niveau du séchage par capteur Temps Temps Temps Normal (Normal) Élevé (Moyen) Séchage normal 42 min 39 min 3 min Heavy Duty (Grand Rendement) Élevé (Aucun changement) Séchage normal 58 min 55 min 3 min Perm Press (Perm Press) Moyen (Aucun changement) Séchage normal 32 min 29 min 3 min Delicates (Délicats) Bas (Aucun changement) Séchage normal
garantie SECHE-LINGE SAMSUNG GARANTIE LIMITÉE À L’ACHETEUR INITIAL Ce produit de la marque SAMSUNG, fourni, distribué par SAMSUNG ELECTRONICS AMERICA, INC. (SAMSUNG) et livré neuf, dans son emballage d’origine à l’acheteur initial, est garanti par SAMSUNG contre tout défaut de fabrication relatif aux matériaux et à la qualité d’exécution, pour une période de garantie limitée de : Un (1) an (pièces et main d’œuvre) Cette garantie limitée prend effet à la date originale d’achat.
SAUF EXCEPTION MENTIONNÉE DANS LE PRÉSENT DOCUMENT, SAMSUNG NE FOURNIT AUCUNE GARANTIE EXPRESSE OU IMPLICITE QUANT À CET APPAREIL, Y COMPRIS, MAIS SANS S’Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE, DE CONTREFAÇON OU D’APTITUDE À UN USAGE PARTICULIER. AUCUNE GARANTIE, QU’ELLE SOIT DONNÉE PAR UN TIERS, UNE ENTREPRISE OU UNE PERSONNE MORALE, NE POURRA ÊTRE CONSIDÉRÉE COMME UN ENGAGEMENT VIS-À-VIS DE SAMSUNG.
QUESTIONS OU COMMENTAIRES ? Pays APPELEZ LE OU RENDEZ-VOUS SUR LE SITE CANADA 1-800-SAMSUNG (726-7864) www.samsung.com N° code DC68-02820B-03_CFR DV340AE-02820B-03_CFR.