the possibilities Thank you for purchasing this Samsung product, To recewe more cc _nolete serwce, please register your product at www, samsung.com/register DV350-02821A EN.
1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra large 7.4 cu.ft, capacity dryer circulates more air through your clothes, drying them faster for a wrinkle-free result. 2. Steam cycle This cycle sprays a small amount of water into the dryer drum after several minutes of tumbling with heat. It reduces bad odors from clothing that are difficult to remove when washing with water, and also reduces wrinkles. 3.
C Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer's many benefits and features. WARNING • - Risk of Fire Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer's instructions and local codes. Do not install a clothes dryer with flexible plastic venting materials.
WHAT TO DO IF YOU SMELL GAS: • Do not try to light any appliance. Do not turn on the appliance. Do not touch any electrical switch. Do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance. Do not sit on top of the dryer. ® Because of continuing product improvements, Samsung reserves the right to change specifications without notice.
content INSTALLING OPERATING YOUR DRYER INSTRUCTIONS, TIPS CARE AND CLEANING SPECIAL LAUNDRY TIPS TROUBLESHOOTING APPENDIX 7 Tools needed for installation 7 8 9 9 See Dryer Exterior Ducting requirements Important to installer Location considerations 9 10 Alcove or closet installation Mobile home installation 10 11 12 Exhausting Gas requirements Electrical requirements 12 13 Grounding Electrical connections 14 15 15 Connecting the inlet hose Replacement parts and accessories Installati
ncj 7o ArdrTer TOOLS NEEDED FOR INSTALLATION Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup, adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer, you are responsible. Make sure you have everything necessary for proper installation. 1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. 2. A POWER CORD for electric dryers (except Canada). 3. 4.
DUCTING • REQUIREMENTS Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. Ducts larger than 4 inches (10.2 cm) Lint accumulation should be cleaned If a flexible metal duct must be used, with a thin foil wall. Serious blockage in diameter can result in increased lint accumulation. regularly. use the type with a stiff sheet metal wall. Do not use a flexible duct can result if the flexible metal duct is bent too sharply.
If the new dryer is installed sure: ,, • • • into an existing exhaust system you must make The exhaust system meets all local, state, and national codes. That a flexible plastic duct is not used. To Inspect and clean all lint buildup from inside the existing duct. The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
MOBILE HOME INSTALLATION The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made. Locate an area that has adequate fresh air.
GAS REQUIREMENTS Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WiTH THE NATIONAL FUEL GAS CODE ANSVZ223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.
ELECTRICAL _ REQUIREMENTS Wiring diagram is located on the plate below the control panel. WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer - if it doesn't fit the outlet, have a proper outlet installed by a qualified electrician.
ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models - U.S. and Canada A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models - U.S. only Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service.
CONNECTING THE iNLET HOSE Method1 The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. If space permits, attach the brass female end of the "Y" connector to the cold water faucet. 2. Turn the cold water faucet off. 3. Attach the straight end of long hose to "Y' connector. 4. Using pliers, tighten the coupling with an additional twothirds turn. (_Do not overtighten, as it may damage the coupling. 5.
REPLACEMENT PARTS AND ACCESSORIES If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864). i NSTALLATION Gather the required tools and parts before starting the installation. Read and follow the instructions provided with any tools listed here.
4. Review the Exhausting section before installing the exhaust system. Install the ductwork from your dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic flexible exhaust material. Tip for tight installations: install a section of exhaust system to your dryer before putting it in place.
6. Review Gas Requirements section. Remove the pipe thread protective cap. Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections. _Pipe joint compound must be resistant to the action of any liquefied petroleum gas. Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4" (1.9 cm) female thread end of a flexible connector to the 3/8" (1 cm) male threaded end on the dryer. Securely tighten the gas line fitting over threads.
4-WIRE system connections 1. Remove the center terminal block screw. 2. Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw. 3. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow 4. stripes) under the central screw of the terminal block. Connect the other wires to the outer terminal block screws. Tighten screws. 3 5. Tighten the strain relief screws. 6.
DRYER EXHAUST _ TIPS Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 1. Make sure your dryer is installed properly so it exhausts air easily. 2. Use a 4" diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. ( I 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually.
DOOR REVERSAL 1. Unplug the power cord. 2. Remove two door hinge screws. 3. Lift the door and remove it. 4. Remove a screw on the Frame Front. 5. Remove the two screws on the opposite side of the door hinge. 6. Remove two screws from the holder lever. 7. Remove one black screw from the door hinge. 20 hstaling DV350-O2821A EN.indd 20 7. Reinsert the black screw in the other hole. 9. Reinsert the screw (Step 4) on the Frame Front. _' j:::i, \ G, ',, 10.
OVERVIEW OF THE CONTROL N _ _ Normal eavy uu_y _, Perm Press ___ Oe,cates _. _ rime ury Manual Dry ..... Quick Dry ,e,,es, @ ;; PANEL _3 More Dry [ } High @ Normal Dry 5 Medium Q Less Dry [} Low D Damp Dry [: Extra Low 20rnin, Dry Level Temp. Time @ @ @ @ 40rnin. _; 30min, D Louder [3 Softer {] Off Signal @©@ @ To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate.
The display window shows the estimated time remaining in the cycle after the Start/Pause button is pressed. The estimated time remaining may fluctuate as the cycle progresses. The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is in the cool-down phase, the Cooling light will illuminate. When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will illuminate.
Mixed Load Bell - This is an alarm that notifies the user when the average dry level is damp dry (80% dried). This is useful when the laundry contains various types of clothing you do not want to dry completely. An alarm sounds for five (5) seconds while continuing to perform the cycle. This function can only be selected in the Sensor Dry course, and the dry level can only be selected from among Normal Dry, More Dry.
DRUM LIGHT Lights the dryer drum while the dryer is running. Setting & releasing If you want to set or release the Drum Light, press both the Dry Level and Temp. buttons simultaneously. lt can be set while your dryer is not only running but also when it is stopped. If you do not turn the Drum Light off within 4 minutes of turning it on, it is automatically turned off. CHANGING THE LANGUAGE You may change the language shown in the display from English to French or Spanish.
RACK DRY Installing the drying rack 1. Open the dryer door. 2. Position the drying rack in the tumbler, placing the front lip of the drying rack on the top of the lint filter. 3. Place the rear legs in the two recessed areas of the dryer's back wall, then push down the middle of the drying rack to fix. 4. Place the items to be dried on the rack, leaving space between them so air can circulate. 5. Close the dryer door. 6. Use the Time Dry cycle.
CLEAN THE LINT FILTER • After each load. • To shorten drying time. • To operate more energy efficiently. Cleaning the Lint filter 1. Pull the case-filter out of the dryer. 2. Scrape the dust from the top part of the filter using your fingers. 3. Open the bottom cover and scrape the dust in the same way. 4. Shake off the dust, close the cover and install it in its place. not operate your dryer without the lint filter in place.
CONTROL PANEL Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel. The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your dryer and wipe up any spills or overspray immediately. TUMBLER Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an allpurpose cleaner.
SPECIAL LAUNDRY TIPS Please follow the care label or manufacturer's instructions for drying special items. If care label instructions are not available, use the following information a guide, Bedspreads & Comforters * * * Blankets * * Curtains & Draperies * * as Follow the care label instructions or dry on the Normal cycle and High temperature. Make sure the item is thoroughly dry before using or storing. May require repositioning to ensure even drying.
troLAbe hootncj CHECK THESE POINTS Doesn't run. • IF YOUR DRYER... Make sure the door is latched shut. Be sure the power cord is plugged into a live electrical outlet. Check the home's circuit breaker and fuses. Press the Start/Pause button again if the door is opened during the cycle. Doesn't heat. Check the home's circuit breaker and fuses. Select a heat setting other than Air Fluff. On a gas dryer, check that the gas supply is on. Clean the lint filter and exhaust duct.
Shuts off before load is dry • Dryer load is too small. Add more items or a few towels and restart the cycle. Dryer load is too large. Remove some items and restart the dryer. Lint on clothes Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.
INFORMATION CODES Information codes may be displayed to help you better understand what is occurring with your Dryer. tS tO dO Clogged Lint Screen Vent is restricted Clean the screen or vent. Running the dryer with door open Close the door and then restart. If the problem continues call for service. If the problem continues call for service. dF Door is not closing properly Call for service.
FABRIC CARE CHART The following symbols provide garment care direction. The Clothing care labels include symbols for washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to maximize garment life and reduce laundering problems.
PROTECTING THE ENVIRONMENT This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. DECLARATION OF CONFORMITY This appliance complies with UL2158. SPECIFICATIONS " " c " " - - i D_ DIMENSIONS DiV 38.6" (98.1) B. Width 27" (68.
CYCLE CHART i??_!_!_i_i_i_i_ii_il!_ii_!_;_(i_i_iiiiii!i!_i_i_i!i!_!i!_!i!!iiiiiii_!_!_ iiiiiiiiii!!_;_!!_;!;!!!iiiiiiii!iiii_i_i_i_iiiiiiiiii_i_!_;_ii_!!_ i_i_i!ii;iiiiiiiiiii_i_!i_i_!i!_i!ili_i_ii_ii_i ¸ High (No change) 3 min Normal dry 58 min 55 min 3 min Normal dry 32 min 29 min 3 min Normal dry 27 min 24 min 3 min More dry 60 min 55 min 5 min High 40 min 37 min 3 min Quick Dry High (No change) 30 min 27 min 3 min Refresh High (No change) 15 min 14 min 1 min Wrinkle-Car
SAMSUNG DRYER LiMiTED WARRANTY TO ORiGiNAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
\ EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
DV350-02821A EN.
QUESTIONS OR COMMENTS? U.S.A 1-800-SAMSUNG(726-7864) www,samsung.com MEXICO 01-800-SAMSUNG(726-7864) www,samsung.com Code No.
