DV419AE* DV419AG* Gas and Electric Dryer user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register DV419AEW-02656A_EN.
features 1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultralarge 7.4 cu.ft. capacity dryer circulates more air through your clothes, drying them faster for a wrinkle-free result. 2. Steam cycle This cycle sprays a small amount of water into the dryer drum after several minutes of tumbling with heat. It reduces bad odors from clothing that are difficult to remove when washing with water, and also reduces wrinkles. 3.
safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WARNING - Risk of Fire • • • • Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer’s instructions and local codes.
safety instructions WHAT TO DO IF YOU SMELL GAS: • • • • • • Do not try to light any appliance. Do not turn on the appliance. Do not touch any electrical switch. Do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department.
The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance. Do not sit on top of the dryer. Because of continuing product improvements, Samsung reserves the right to change specifications without notice.
contents INSTALLING YOUR DRYER 7 7 8 9 9 9 10 10 11 12 12 13 14 15 15 18 19 20 21 23 24 24 24 25 26 26 26 27 27 27 27 27 Tools needed for installation See Dryer Exterior Ducting requirements Important to installer Location considerations Alcove or closet installation Mobile home installation Exhausting Gas requirements Electrical requirements Grounding Electrical connections Connecting the inlet hose Replacement parts and accessories Installation Final installation checklist Dryer Exhaust Tips Door Revers
installing your dryer TOOLS NEEDED FOR INSTALLATION SEE DRYER EXTERIOR 01 Installing your dryer Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup, adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer you are responsible. Make sure you have everything necessary for proper installation. 1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. 2.
installing your dryer DUCTING REQUIREMENTS • • • • • • • • • • • • • • • • • • • Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation. Lint accumulation should be cleaned regularly. If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall.
If the new dryer is installed into an existing exhaust system you must make sure: 01 Installing your dryer • The exhaust system meets all local, state, and national codes. • That a flexible plastic duct is not used. • To Inspect and clean all lint buildup from inside the existing duct. • The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
installing your dryer MOBILE HOME INSTALLATION The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made. Locate an area that has adequate fresh air.
GAS REQUIREMENTS • • 01 Installing your dryer Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas.
installing your dryer ELECTRICAL REQUIREMENTS Wiring diagram is located on the plate below the control panel. • WARNING • • Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require 120/208 volt, 60 Hz approved electrical service.
installing your dryer CONNECTING THE INLET HOSE Method1 The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. If space permits, attach the brass female end of the “Y” connector to the cold water faucet. 2. Turn the cold water faucet off. 3. Attach the straight end of long hose to “Y’ connector. 4. Using pliers, tighten the coupling with an additional twothirds turn. Do not overtighten, as it may damage the coupling. 5.
REPLACEMENT PARTS AND ACCESSORIES If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864). 01 Installing your dryer INSTALLATION Gather the required tools and parts before starting the installation. Read and follow the instructions provided with any tools listed here.
installing your dryer 4. Review the Exhausting section before installing the exhaust system. Install the ductwork from your dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic flexible exhaust material. Tip for tight installations: install a section of exhaust system to your dryer before putting it in place.
6. Review Gas Requirements section. Remove the pipe thread protective cap. Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections. Pipe joint compound must be resistant to the action of any liquefied petroleum gas. 3-WIRE system connections 01 Installing your dryer Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4” (1.9 cm) female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer.
installing your dryer 4-WIRE system connections 1. Remove the center terminal block screw. 2. Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw. 3. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block. 4. Connect the other wires to the outer terminal block screws. Tighten screws. 5. Tighten the strain relief screws. 6.
DRYER EXHAUST TIPS Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 01 Installing your dryer 1. Make sure your dryer is installed properly so it exhausts air easily. 2. Use 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually.
installing your dryer DOOR REVERSAL 1. Unplug the power cord. 2. Remove two door hinge screws. 3. Lift the door and remove it. 7. Reassemble the black screw in the other hole. 4. Remove a screw on the Frame Front 9. Reinsert the screw (Step 4) on the Frame Front 5. Remove the two screws on the opposite side of the door hinge. 10. Place the door on the other side and reattach it to the dryer. 6. Remove two screws from the holder lever. 11. Reattach the holder lever. 7.
operating Instructions, tips OVERVIEW OF THE CONTROL PANEL 1 Cycle Selector 2 6 3 4 5 6 7 8 To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate. The Normal, Heavy Duty, Towels, Perm Press, Delicates and Sanitize cycles are Sensor Dry cycles. Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level (very dry to damp dry) is reached.
operating Instructions, tips 2 3 4 5 Digital Graphic Display The display window shows the estimated time remaining in the cycle after the Start/Pause button is pressed. The estimated time remaining may fluctuate as the cycle progresses. The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is in the cool-down phase, the Cooling light will illuminate. When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will illuminate.
Select Cycle Option 7 Start/Pause selection button Press to pause and restart programs. 8 Power button Press once to turn your dryer on, press again to turn it off. If your dryer is left on for more than 10 minutes without any buttons being touched, the power automatically turns off. 02 Operating Instructions, Tips 6 Adjust Time – Time can be added or subtracted from the automatically set times in the Manual Dry cycles (Time Dry, Quick Dry, or Air Fluff cycles).
operating Instructions, tips DRUM LIGHT Lights the dryer drum while the dryer is running. Setting & releasing If you want to set or release the Drum Light, press both the Dry Level and Temp. buttons simultaneously. It can be set while your dryer is not only running but also when it is stopped. If you do not turn the Drum Light off within 4 minutes of turning it on, it is automatically turned off. CHANGING THE LANGUAGE You may change the language shown in the display from English to French or Spanish.
RACK DRY Installing the drying rack SUGGESTED ITEMS SUGGESTED TEMP. SETTINGS Washable sweaters (block to shape and lay flat on rack) Heat (Extra Low) Stuffed toys (cotton or polyester fiberfilled) Heat (Extra Low) Stuffed toys (foam or rubber-filled) Air Fluff Foam rubber pillows Air Fluff Sneakers Air Fluff WARNING 02 Operating Instructions, Tips 1. Open the dryer door. 2. Position drying rack in tumbler, placing the front lip of the drying rack on the top of the lint filter. 3.
operating Instructions, tips CLEAN THE LINT FILTER • • • After each load. To shorten drying time. To operate more energy efficiently. Do not operate your dryer without the lint filter in place. LOAD THE DRYER PROPERLY • • • • Place only one washload in your dryer at a time. Mixed loads of heavy and lightweight fabrics will dry differently, which may result in lightweight fabrics being dry while heavy fabrics remain damp at the end of a drying cycle.
care and cleaning CONTROL PANEL TUMBLER Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an allpurpose cleaner. Tumble old towels or rags to remove any excess stain or cleaning substance. Once these steps are followed, stains may still be visible, but should not transfer to subsequent loads. 03 Care and cleaning Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel.
special laundry tips SPECIAL LAUNDRY TIPS Please follow the care label or manufacturer’s instructions for drying special items. If care label instructions are not available, use the following information as a guide. Bedspreads & Comforters • • • Blankets • • Curtains & Draperies • • Follow the care label instructions or dry on the Normal cycle and High temperature. Make sure the item is thoroughly dry before using or storing. May require repositioning to ensure even drying.
troubleshooting CHECK THESE POINTS IF YOUR DRYER… SOLUTION Doesn’t run. • • • • Make sure the door is latched shut. Be sure the power cord is plugged into a live electrical outlet. Check the home’s circuit breaker and fuses. Press the Start/Pause button again if the door is opened during the cycle. Doesn’t heat. • • • • • Check the home’s circuit breaker and fuses. Select a heat setting other than Air Fluff. On a gas dryer, check that the gas supply is on. Clean the lint filter and exhaust duct.
troubleshooting PROBLEM SOLUTION Shuts off before load is dry • • Lint on clothes • • • • Garments still wrinkled after • Wrinkle-Care • Dryer load is too small. Add more items or a few towels and restart the cycle. Dryer load is too large. Remove some items and restart the dryer. Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.
INFORMATION CODES Information codes may be displayed to help you better understand what is occurring with your Dryer. ERROR DISPLAY MEANING SOLUTION Clean the screen or vent. If the problem continues call for service. dO Running the dryer with door open Close the door and then restart. If the problem continues call for service. dF Door is not closing properly Call for service. bE Invalid state of key circuit short for 30secs Make sure a button is NOT being pressed continuously.
appendix FABRIC CARE CHART The following symbols provide garment care direction. The Clothing care labels include symbols for washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to maximize garment life and reduce laundering problems.
PROTECTING THE ENVIRONMENT DECLARATION OF CONFORMITY This appliance complies with UL2158. 06 Appendix This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance.
appendix CYCLE CHART Default Cycle Cooling Wrinkle prevent Temp control Sensor dry level Time Time Time Time Normal High (Medium) Normal dry 44 min 39 min 5 min 90 min Heavy Duty High (No change) Normal dry 60 min 55 min 5 min 90 min Towels High (Medium) Normal dry 52 min 47 min 5 min 90 min Perm Press Medium (No change) Normal dry 34 min 24 min 10 min 90 min Delicates Low (No change) Normal dry 29 min 24 min 5 min 90 min Sanitize High (No change) Very dry 60 m
warranty SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
warranty EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
memo DV419AEW-02656A_EN.
QUESTIONS OR COMMENTS? Country CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com/us MEXICO 01-800-SAMSUNG(726-7864) www.samsung.com/mx Code No. DC68-02656A_EN DV419AEW-02656A_EN.
DV419AE* DV419AG* Secadora a gas y eléctrica Manual del usuario imagina las posibilidades Gracias por adquirir este producto Samsung. Para que podamos brindarle un servicio más completo, registre su producto en www.samsung.com/register DV419AEW-02656A_MES.
características 1. Capacidad extra grande ¡Capacidades de ultra secado al alcance de la mano! Ahora puede secar cargas extra grandes. Nuestra secadora ultra grande, con 7.3 cu.ft. (13 kg) de capacidad, hace circular más aire entre su ropa, secándola más rápido, para obtener un resultado sin arrugas. 2. Ciclo Steam (vapor) Este ciclo rocía una pequeña cantidad de agua en el tambor de la secadora después de varios minutos de secado con calor.
instrucciones de seguridad Felicitaciones por la compra de la nueva secadora Samsung. Este manual contiene información importante acerca de la instalación, el uso y el cuidado del electrodoméstico. Lea detenidamente estas instrucciones a fin de aprovechar al máximo los múltiples beneficios y funciones de la secadora. ADVERTENCIA - Riesgo de incendio • • • • La instalación de la secadora de ropa debe estar a cargo de un instalador calificado.
instrucciones de seguridad QUÉ HACER SI PERCIBE OLOR A GAS: • • • • • • No intente encender ningún electrodoméstico. No encienda el electrodoméstico. No toque ningún interruptor eléctrico. No utilice ningún teléfono de su edificio. Haga que todos los ocupantes se retiren del cuarto, edificio o área. Comuníquese inmediatamente con el proveedor de gas desde el teléfono de un vecino. Siga las instrucciones del proveedor de gas.
Este electrodoméstico debe conectarse a tierra correctamente. Nunca enchufe el cable de alimentación a un receptáculo que no esté conectado a tierra correctamente ni guarde conformidad con los códigos locales y nacionales. Consulte las instrucciones de instalación para conectar este electrodoméstico a tierra. No se siente encima de la secadora. Debido a las constantes mejoras a los productos, Samsung se reserva el derecho de modificar las especificaciones sin previo aviso.
contenido INSTALACIÓN DE LA SECADORA 20 Herramientas necesarias para la instalación Consulte Exterior de la secadora Requisitos para el tendido de conductos Importante para el instalador Consideraciones acerca de la ubicación Instalación del electrodoméstico en un gabinete o en un hueco Instalación en casas rodantes Drenaje Requisitos en cuanto al gas Requisitos eléctricos Conexión a tierra Conexiones eléctricas Conexión de la manguera de entrada Reemplazo de las piezas y los accesorios Instalación Lista
instalación de la secadora HERRAMIENTAS NECESARIAS PARA LA INSTALACIÓN CONSULTE EXTERIOR DE LA SECADORA 01 Instalación de la secadora Contrate a un profesional para instalar la secadora adecuadamente. En caso de que sea necesaria una visita del servicio técnico como consecuencia de una mala configuración, ajuste y conexión, se considerará responsabilidad del instalador. Si usted mismo instala la secadora, usted será el responsable.
instalación de la secadora REQUISITOS PARA EL TENDIDO DE CONDUCTOS • • • • • • • • • • • • • • • • • • • Utilice un conducto de acero galvanizado rígido o de aluminio rígido, de 4 pulgadas (10,2 cm) de diámetro. No utilice un conducto de menor tamaño. Los conductos de más de 4 pulgadas (10,2 cm) de diámetro pueden ocasionar una mayor acumulación de pelusa. Periódicamente, debe retirar la pelusa acumulada.
Si la nueva secadora se instala dentro de un sistema de drenaje existente, debe asegurarse de que: IMPORTANTE PARA EL INSTALADOR Lea las siguientes instrucciones con detenimiento antes de instalar la secadora. Estas instrucciones se deben conservar para consultas futuras.
instalación de la secadora INSTALACIÓN EN CASAS RODANTES La instalación de la secadora en casas rodantes debe cumplir con la Norma de Construcción y Seguridad de Casas Fabricadas, Título 24 CFR, Parte 3280 [denominada anteriormente Norma Federal para la Construcción y la Seguridad de Casas Rodantes, Título 24, HUD (Parte 280), 1975] (para los Estados Unidos) o las Normas CSA Z240 (para Canadá). Cuando se instala una secadora en una casa rodante, se debe tener la precaución de asegurar la secadora al piso.
REQUISITOS EN CUANTO AL GAS • • 01 Instalación de la secadora Utilice únicamente gas natural o gas LP (gas licuado de propano). LA INSTALACIÓN DEBE REALIZARSE EN CONFORMIDAD CON LOS CÓDIGOS LOCALES, O EN AUSENCIA DE ELLOS, CON EL CÓDIGO NACIONAL PARA GAS Y COMBUSTIBLES ANSI/ Z223.1, LA REVISIÓN MÁS RECIENTE (PARA LOS ESTADOS UNIDOS), O CON LOS CÓDIGOS DE INSTALACIÓN CAN/CGA-B149 (PARA CANADÁ).
instalación de la secadora REQUISITOS ELÉCTRICOS El diagrama del cableado se encuentra en la placa debajo del panel de control. • ADVERTENCIA • • La conexión inadecuada del conductor de conexión a tierra del equipo puede generar una descarga eléctrica. Consulte a un electricista o técnico calificado si le surgen dudas acerca de si la conexión a tierra de su secadora es correcta.
CONEXIONES ELÉCTRICAS Modelos a gas – EE.UU. y Canadá Se requiere un servicio eléctrico aprobado de CA de 120 voltios, 60 Hz, con un fusible o disyuntor de 15 A. Modelos eléctricos – Sólo EE.UU. La mayor parte de las secadoras estadounidenses requieren un servicio eléctrico aprobado de CA de 120/240 voltios, 60 Hz. Algunas requieren un servicio eléctrico aprobado de 120/208 voltios, 60 Hz. Los requisitos del servicio eléctrico pueden encontrarse en la etiqueta con información ubicada detrás de la puerta.
instalación de la secadora CONEXIÓN DE LA MANGUERA DE ENTRADA Método 1 La secadora debe conectarse a la llave de agua fría mediante las nuevas mangueras de entrada. No utilice mangueras viejas. 1. Si el espacio lo permite, conecte el extremo hembra de bronce del conector en forma de “Y” a la llave de agua fría. 2. Cierre la llave de agua fría. 3. Conecte el extremo recto de la manguera larga al conector en forma de “Y”. 4. Ajuste la unión con dos tercios de giro adicionales utilizando la pinza.
REEMPLAZO DE LAS PIEZAS Y LOS ACCESORIOS Si es preciso reemplazar piezas o accesorios de la secadora, comuníquese con el distribuidor al que le compró la secadora o con el centro de atención al cliente de SAMSUNG al 1-800-SAMSUNG (726-7864). INSTALACIÓN 01 Instalación de la secadora Reúna las herramientas y piezas necesarias antes de comenzar la instalación. Lea y siga las instrucciones provistas con cualquier herramienta enumerada aquí.
instalación de la secadora 4. Consulte la sección Drenaje antes de instalar el sistema de drenaje. Instale la red de conductos desde la secadora hasta la tapa de drenaje. El extremo con reborde de las secciones del conducto deben apuntar hacia afuera de la secadora. NO utilice tornillos con recubrimiento de metal cuando realice el montaje de los conductos. Se les debe colocar cinta a las uniones. Nunca utilice material de plástico flexible para el drenaje.
6. Consulte la sección Requisitos en cuanto al gas. Retire la cubierta protectora de la rosca para tubos. Aplique compuesto de unión de tuberías o 1 1/2 vueltas aproximadamente de cinta de teflón en todas las conexiones roscadas. Conecte el suministro de gas a la secadora. Se requiere un accesorio adicional para conectar el extremo de la rosca hembra de 3/4” (1,9 cm) de un conector flexible al extremo de la rosca macho de 3/8” (1 cm) de la secadora.
instalación de la secadora Conexiones de sistemas de 4 CABLES 1. Retire el tornillo central del bloque de terminales. 2. Conecte el cable a tierra (verde o sin cubierta) del cable de alimentación al tornillo conductor a tierra externo. 3. Conecte el cable neutro (cable blanco o central) del cable de alimentación y el cable a tierra del electrodoméstico (verde con franjas amarillas) debajo del tornillo central del bloque de terminales. 4.
SUGERENCIAS ACERCA DEL DRENAJE DE LA SECADORA ADVERTENCIA Un conducto flexible de plástico o de un material que no sea el metal presenta un potencial riesgo de incendio. 01 Instalación de la secadora 1. Asegúrese de que su secadora esté instalada correctamente para que extraiga el aire fácilmente. 2. Utilice un conducto de metal rígido, de 4” de diámetro. Coloque cinta en todas las uniones, incluso en la secadora. Nunca use tornillos que atrapen pelusa. 3. Mantenga los conductos lo más recto posible.
instalación de la secadora INVERSIÓN DE LA PUERTA 1. Desconecte el cable de alimentación. 2. Retire los dos tornillos de la bisagra de la puerta. 3. Levante la puerta y retírela. 8. Vuelva a colocar los tornillos negros en los otros orificios. 4. Retire un tornillo del frente delantero. 9. Vuelva a colocar el tornillo (Paso 4) en el frente delantero. 5. Retire los dos tornillos del lado opuesto de la bisagra de la puerta. 10. Coloque la puerta sobre el lado contrario y vuelva a fijar a la secadora. 6.
manual de instrucciones, sugerencias DESCRIPCIÓN GENERAL DEL PANEL DE CONTROL 1 Selector de ciclos 2 6 3 4 5 6 7 8 Paraseleccionar un ciclo, gire el disco Selector de ciclos hasta llegar al ciclo deseado. La luz del indicador junto al nombre del ciclo se iluminará. Los ciclos Normal (Normal), Heavy Duty (Servicio pesado), Towels (Toallas), Perm Press (Plancha permanente), Delicates (Prendas delicadas) y Sanitize (Desinfección) son ciclos Sensor Dry (Secado con sensor).
manual de instrucciones, sugerencias 2 3 4 5 Pantalla gráfica digital Botón de selección Dry Level (Nivel de secado) Botón de selección Temp (Temperatura) Botón de selección Time (Tiempo) Lapantalla digital muestra el tiempo restante del ciclo calculado después de presionar el botón Start/Pause (Inicio/Pausa). El tiempo restante calculado puede fluctuar a medida que avance el ciclo. Se iluminará la luz de Drying (Secar) y se mantendrá iluminada hasta que se haya cumplido el ciclo.
7 8 Opción de selección de ciclo Botón de selección Start/Pause (Inicio/ Pausa) Presiónelo para detener y reiniciar los programas. Botón Power (Encendido) Presiónelo una vez para encender la secadora y presiónelo nuevamente para apagarla. Si la secadora permanece encendida durante más de 10 minutos sin que se presione ninguno de los botones, se apagará automáticamente.
manual de instrucciones, sugerencias LUZ DEL TAMBOR Enciende el tambor de la secadora mientras se realiza el secado. Configuración y liberación Si desea configurar o liberar esta función, presione simultáneamente los botones Dry Level (Nivel de secado) y Temp. (Temperatura). Puede configurarse no sólo cuando su secadora está en funcionamiento sino también cuando está detenida. Si no apaga la luz del tambor antes de 4 minutos después de que se encienda, la luz del tambor se apaga automáticamente.
RACK DRY (SECADO EN ESTANTE) Instalación del estante de secado PRENDAS SUGERIDAS OPCIONES DE TEMP.
manual de instrucciones, sugerencias LIMPIE EL FILTRO PARA PELUSAS • • • Después de cada carga. Para reducir el tiempo de secado. Para hacer uso de la energía con mayor eficacia. No haga funcionar la secadora sin el filtro para pelusas colocado. CARGUE LA SECADORA DE MANERA ADECUADA • • • • Coloque sólo una carga de ropa en la secadora por vez.
cuidado y limpieza PANEL DE CONTROL TAMBOR Elimine todas las manchas, tales como las de crayón, tinta o tintura de la tela (proveniente de artículos nuevos, tales como toallas o jeans) con un limpiador común. Posteriormente, seque las toallas o prendas viejas para eliminar todo exceso de manchas o solución de limpieza. Una vez que se hayan seguido estos pasos, es posible que las manchas aún sean visibles, pero no se transferirán a las cargas subsiguientes.
sugerencias para prendas especiales SUGERENCIAS PARA PRENDAS ESPECIALES Siga las instrucciones del fabricante o de la etiqueta de indicaciones para secar prendas especiales. Si no se dispone de etiquetas con indicaciones, use la siguiente información como guía. Cubrecamas y edredones • • • Frazadas • • Cortinas y paños de tela • • Siga las instrucciones de la etiqueta o seque en el ciclo Normal (Normal) y con temperatura High (Alta).
guía de solución de problemas CONTROLE ESTOS PUNTOS SI SU SECADORA… SOLUCIÓN No funciona. • • • • No calienta. • • • • • No seca. • • • • • • • • • Hace ruido. • • • • Asegúrese de que la puerta esté cerrada con traba. Asegúrese de que el cable de alimentación esté enchufado a un tomacorriente que funcione. Controle los disyuntores y fusibles de la casa. Presione el botón Start/Pause (Inicio/Pausa) nuevamente si la puerta se abre durante el ciclo. Controle los disyuntores y fusibles de la casa.
guía de solución de problemas PROBLEMA SOLUCIÓN No seca de manera uniforme. • • Tiene olor. • • Se apaga antes de que la carga esté seca • • Pelusa en las prendas • • • • Prendas arrugadas después • del ciclo Wrinkle-Care • (Antiarrugas) Es posible que las costuras, los bolsillos y otras áreas resistentes similares no se sequen por completo cuando el resto de la carga ha llegado al nivel de secado seleccionado. Esto es normal. Seleccione la opción Very Dry (Muy seco) si lo desea.
CÓDIGOS DE INFORMACIÓN Pueden aparecer códigos de información para ayudarle a comprender mejor qué ocurre con la secadora. PANTALLA DE ERROR SIGNIFICADO SOLUCIÓN Limpie el filtro o el conducto de ventilación. Si el problema continúa, llame al servicio técnico. dO La secadora funciona con la puerta abierta Cierre la puerta y luego reinicie. Si el problema continúa, llame al servicio técnico. dF La puerta no está bien cerrada Solicite servicio técnico.
apéndice TABLA DE INDICACIONES DEL TEJIDO Los siguientes símbolos ofrecen indicaciones acerca de las prendas. La etiqueta de indicaciones de la prenda incluye símbolos para lavado, blanqueado, secado y planchado, o limpieza a seco cuando sea necesaria. El uso de símbolos garantiza la consistencia entre los fabricantes textiles de artículos nacionales e importados. Siga las indicaciones de la etiqueta para prolongar la vida útil de la prenda y reducir los problemas del lavado.
PROTECCIÓN DEL MEDIO AMBIENTE DECLARACIÓN DE CONFORMIDAD Este electrodoméstico cumple con la norma UL2158. 06 Apéndice Este electrodoméstico se fabrica con materiales reciclables. Si decide deshacerse de este electrodoméstico, siga la normativa local relacionada con la eliminación de desechos. Corte el cable de alimentación para que el electrodoméstico no pueda conectarse a una fuente de alimentación.
apéndice TABLA DE CICLOS Predeterminado Ciclo Enfriar Prevención de arrugas Control de temp. Nivel de secado con sensor Tiempo Tiempo Tiempo Tiempo Normal High (Medium) (Alta (Media)) Normal dry (Secado normal) 44 min. 39 min. 5 min. 90 min. Heavy Duty (Servicio pesado) High (No change) (Alta (Sin cambios)) Normal dry (Secado normal) 60 min. 55 min. 5 min. 90 min. Towels (Toallas) High (Medium) (Alta (Media)) Normal dry (Secado normal) 52 min. 47 min. 5 min. 90 min.
garantía SECADORA SAMSUNG GARANTÍA LIMITADA PARA EL COMPRADOR ORIGINAL El presente producto de la marca SAMSUNG, tal como lo provee y distribuye SAMSUNG ELECTRONICS AMERICA, INC.
garantía EXCEPTO LO ESTABLECIDO EN EL PRESENTE, NO EXISTEN GARANTÍAS SOBRE ESTE PRODUCTO, YA SEAN EXPRESAS O TÁCITAS, Y SAMSUNG DESCONOCE TODAS LAS GARANTÍAS QUE INCLUYEN, AUNQUE NO EN CARÁCTER TAXATIVO, CUALQUIER GARANTÍA TÁCITA DE QUE EL PRODUCTO SE ENCUENTRA EN CONDICIONES APTAS PARA LA VENTA, DE DEFRAUDACIÓN DE DERECHOS O DE QUE EL PRODUCTO SE ADECUA A LOS FINES ESPECÍFICOS PARA LOS CUALES SE ADQUIERE.
memo DV419AEW-02656A_MES.
¿TIENE PREGUNTAS O COMENTARIOS? País LLAME AL O VISÍTENOS EN LÍNEA EN U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com/us MEXICO 01-800-SAMSUNG(726-7864) www.samsung.com/mx Número de código DC68-02656A_MES DV419AEW-02656A_MES.