DV431AE* DV431AG* Gas and Electric Dryer user manual This manual is made with 100% recycled paper. imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service or accessory parts, please register your product at or contact www.samsung.com/register DV431AEP-03021D_EN.
features 1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra large 17 kg capacity dryer circulates more air through your clothes, drying them faster for a wrinkle-free result. 3. Sanitize course This course allows you to sanitize garments by permeating high temperature heat deep into the fabric during the drying cycle. Use this course to keep your bedding and curtains clean. When selecting this cycle, 99.
safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WARNING - Risk of Fire • Clothes dryer installation must be performed by a qualified installer. • Install the clothes dryer according to the manufacturer’s instructions and local codes.
safety instructions WARNING WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3.
WHAT TO DO IF YOU SMELL GAS: • • • • • • Do not try to light any appliance. Do not turn on the appliance. Do not touch any electrical switch. Do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
safety instructions The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance. Do not sit on top of the dryer. Because of continuing product improvements, Samsung reserves the right to change specifications without notice.
contents installing your dryer 8 8 9 10 10 11 13 13 14 14 15 16 16 17 19 20 21 Tools needed for installation See Dryer Exterior Ducting requirements Important to installer Location considerations Alcove or closet installation Mobile home installation Exhausting Gas requirements Electrical requirements Grounding Electrical connections Replacement parts and accessories Installation Final installation checklist Dryer Exhaust Tips Door Reversal operating Instructions, tips 22 Overview of the control panel
installing your dryer Tools needed for installation Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup, adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer, you are responsible. Make sure you have everything necessary for proper installation. 1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. 2. A POWER CORD for electric dryers (except Canada). 3.
Ducting requirements • • • • • • • • • • • • • • • • • • 01 installing your dryer • Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation. Lint accumulation should be cleaned regularly. If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall.
installing your dryer If the new dryer is installed into an existing exhaust system you must make sure: • The exhaust system meets all local, state, and national codes. • That a flexible plastic duct is not used. • To Inspect and clean all lint buildup from inside the existing duct. • The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
Alcove or closet installation MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS: A B 1 in. (2.5 cm) 1 in. (2.5 cm) 27 in. (68.6 cm) 17 in. (43.2 cm) 27 in. (68.6 cm) 1 in. (2.5 cm) 2 in. (5 cm) 31.9 in. (81.1 cm) 01 installing your dryer Sides – 1 in / 25 mm Top – 17 in / 432 mm Rear – 5 in / 127 mm Closet Front – 2 in / 51 mm If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²) unobstructed air opening. 5 in. (12.7cm) A. Recessed area B.
installing your dryer With optional pedestal base or stacking kit Required Dimensions for Installation With Pedestal 51.7 in. (131.4 cm) to clear open door 39 in. (99.1 cm) 53.6 in. (136.2 cm) 341.1 in. (86.5 cm) 5 in. (12.7 cm) 27 in. (68.6 cm) 2.5 in. (6.3 cm) 3 in. (7.6 cm) 48 in.² * (310 cm²) 24 in.² * (155 cm²) 3 in. (7.6 cm) Closet or Door 1 in. (2.5 cm) 31.9 in. (81.1 cm) 5.5 in.** (14 cm) Required Dimensions for Installation With Stacking Kit 6 in. * (15.2 cm) 78 in. (198.1 cm) 1 in.
Mobile home installation 01 installing your dryer The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made. Locate an area that has adequate fresh air.
installing your dryer Gas requirements Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas.
Grounding This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for the electrical current. Gas models Your dryer has a cord with an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
installing your dryer Electrical connections Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models Dryers require a 120/240 volt, 60 Hz AC approved electrical service.
Installation Gather the required tools and parts before starting the installation. Read and follow the instructions provided with any tools listed here. Pliers Cutting knife Pipe wrench (gas only) Nut drivers Level Phillips Screwdriver Duct tape Wrench 01 installing your dryer Tools and Parts For proper installation, we recommend that you hire a professional. To install: 1. Move your dryer to an appropriate location for installation.
installing your dryer 4. Review the Exhausting section before installing the exhaust system. Install the ductwork from your dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic flexible exhaust material. Tip for tight installations: install a section of exhaust system to your dryer before putting it in place.
4-WIRE system connections 01 installing your dryer 1. Remove the center terminal block screw. 2. Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw. 3. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block. 4. Connect the other wires to the outer terminal block screws. Tighten screws. 5. Tighten the strain relief screws. 6.
installing your dryer Dryer Exhaust Tips Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 1. Make sure your dryer is installed properly so it exhausts air easily. 2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually.
Door Reversal 8. Reinsert the screw in the other hole. 4. Remove a screw on the Frame Front 9. Reinsert the screw (Step 4) on the Frame Front 5. Remove the two screws on the opposite side of the door hinge. 10. Place the door on the other side and reattach it to the dryer. 6. Remove two screws from the holder lever. 11. Reattach the holder lever. 7. Remove a screw from the door hinge. 12. Reattach the screws in the remaing holes. 01 installing your dryer 1. Unplug the power cord. 2.
operating Instructions, tips WARNING To reduce the risk of fire, electric shock, or injury to persons,read the IMPORTANT SAFETY. INSTRUCTIONS before operating this appliance. Overview of the control panel 1 1 Cycle Selector 2 3 4 5 6 7 8 9 To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate.
3 4 Digital Graphic Display Select Cycle Option Wrinkle Prevent -Wrinkle Prevent provides approximately 180 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling. Press the Wrinkle Prevent button to activate this feature. The indicator light above the pad will illuminate when Wrinkle Prevent is selected. The load is dry, and can be removed at any time during the Wrinkle Prevent cycle.
operating Instructions, tips 5 Temp Selection Button To select the correct temperature for the load, press the Temp button. An indicator light will illuminate next to the desired temperature. Press the button repeatedly to scroll through the settings. High – For sturdy cottons or those labeled Tumble Dry. Medium – For permanent press, synthetics, lightweight cottons, or items labeled Tumble Dry Medium. Medium Low – For lower heat than Medium to dry synthetic or washable knit fabrics.
Child lock A function to prevent children from playing with your dryer. Setting/Releasing How to Set: 1. It can be set while your dryer is running. 2. Once you set the Child Lock function, no button, except for the Power button, will respond until you release the Child Lock function. 3. The Child Lock indicator will be lit. 1. If the dryer is powered on again, the Child Lock function stays on. 2. To release that function, follow the instructions above.
operating Instructions, tips Rack Dry Installing the drying rack 1. Open the dryer door. 2. Position drying rack in tumbler, placing the front lip of the drying rack on the top of the lint filter. 3. Place the rear legs in the two recessed areas of the dryer’s back wall then push down the middle of the drying rack to fix. 4. Place the items to be dried on the rack, leaving space between them so air can circulate. 5. Close the dryer door. 6.
Clean the lint filter • • • After each load. To shorten drying time. To operate more energy efficiently. Frame Front Filter Door Load the dryer properly • • • • Place only one washload in your dryer at a time. Mixed loads of heavy and lightweight fabrics will dry differently, which may result in lightweight fabrics being dry while heavy fabrics remain damp at the end of a drying cycle. Add one or more similar items to your dryer when only one or two articles of clothing need drying.
care and cleaning Control Panel Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel. The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your dryer and wipe up any spills or overspray immediately. Tumbler Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an allpurpose cleaner.
special laundry tips Special laundry tips Bedspreads & Comforters • • • Blankets • • Curtains & Draperies • • Follow the care label instructions or dry on the Normal cycle and High temperature. Make sure the item is thoroughly dry before using or storing. May require repositioning to ensure even drying. Use Normal cycle and dry only one blanket at a time for best tumbling action. Make sure the item is thoroughly dry before using or storing.
troubleshooting Check these points if your dryer… PROBLEM SOLUTION Doesn’t run. • • • • Make sure the door is latched shut. Be sure the power cord is plugged into a live electrical outlet. Check the home’s circuit breaker and fuses. Press the Start/Pause button again if the door is opened during the cycle. Doesn’t heat. • • • • Check the home’s circuit breaker and fuses. On a gas dryer, check that the gas supply is on. Clean the lint filter and exhaust duct.
PROBLEM SOLUTION Shuts off before load is dry • • • • • • Garments still wrinkled after • Wrinkle-Care • Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.
troubleshooting Information codes Information codes may be displayed to help you better understand what is occurring with your Dryer. ERROR DISPLAY Meaning SOLUTION tE Clogged Lint Screen Vent is restricted Clean the screen or vent. If the problem continues, call for service. HE Invalid heating Temp in running the dryer Call for service. dE Running the dryer with door open Close the door and then restart. If the problem continues, call for service.
appendix Fabric care chart Wash Cycle Special Instructions Warning Symbols for Laundering Normal Line Dry/ Hang to Dry Do Not Wash Permanent Press / Wrinkle Resistant / Wrinkle Control Drip Dry Do Not Wring Gentle/Delicates Dry Flat Do Not Bleach Hand Wash Heat Setting Do Not Tumble Dry High No Steam (added to iron) Hot Medium Do Not Iron Warm Low Cold Any Heat Dry Clean No Heat/Air Do Not Dry Clean Water Temperature** Bleach Any Bleach (when needed) Iron-Dry or Steam Temperatu
appendix Protecting the environment This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. Declaration of conformity This appliance complies with UL2158.
Cycle chart Default Cycle Wrinkle prevent Time Sensor dry level Time Time Time Normal High (Medium) Normal dry 42 min 39 min 3 min Heavy Duty High (No change) Normal dry 58 min 55 min 3 min Perm Press Medium (No change) Normal dry 32 min 29 min 3 min Towels High (Medium) Normal dry 50 min 47 min 3 min Bedding High (No change) Normal dry 50 min 47 min 3 min Delicates Extra Low (No change) Normal dry 34 min 33 min 1 min Wool Low (No change) Normal dry (No change) 2
note DV431AEP-03021D_EN.
note DV431AEP-03021D_EN.
QUESTIONS OR COMMENTS? Country CALL OR VISIT US ONLINE AT BRAZIL 0800-124-421 4004-0000 www.samsung.com MEXICO 01-800-SAMSUNG(726-7864) www.samsung.com PANAMA 800-7267 www.samsung.com Code No. DC68-03021D_EN DV431AEP-03021D_EN.