DV448AE* DV448AG* DV438AE* DV438AG* Gas and Electric Dryer user manual This manual is made with 100% recycled paper. imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service or accessory parts, please register your product at or contact www.samsung.com/register 1-800-SAMSUNG (726-7864) DV448AEG-02555A-10_EN.
features 1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultralarge 7.4 cu.ft. capacity dryer circulates more air through your clothes, drying them faster, for a wrinkle-free result. 2. Steam cycle This cycle sprays a small amount of water into the dryer drum after several minutes of tumbling with heat. It reduces bad odors from clothing that are difficult to remove when washing with water, and also reduces wrinkles. 3.
safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur.
safety instructions WARNING WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3.
WARNING - Risk of Fire • • • • WARNING Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer’s instructions and local codes. Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
safety instructions Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets. Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside. Do not reach into the appliance when the drum is moving. Do not install or store this appliance where it will be exposed to the weather. Do not tamper with controls.
contents 13 13 14 15 16 16 19 20 21 Tools needed for installation See Exhaust Requirements Ducting requirements Important to installer Location considerations Alcove or closet installation Mobile home installation Exhausting Gas requirements Commonwealth of Massachusetts installation instructions Electrical requirements Grounding Electrical connections Connecting the inlet hose Replacement parts and accessories Installation Final installation checklist Dryer Exhaust Tips Door Reversal 22 24 25 25 25 26 2
installing your dryer TOOLS NEEDED FOR INSTALLATION Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup, adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer you are responsible. Make sure you have everything necessary for proper installation. 1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. 2. A POWER CORD for electric dryers (except Canada). 3.
DUCTING REQUIREMENTS • • • • • • • • • • • • • • • • • 01 installing your dryer • Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation. Lint accumulation should be cleaned regularly. If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall.
installing your dryer If the new dryer is being installed into an existing exhaust system you must make sure: • The exhaust system meets all local, state, and national codes. • That a flexible plastic duct is not used. • To Inspect and clean all lint buildup from inside the existing duct. • The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
MOBILE HOME INSTALLATION 01 installing your dryer The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made. Locate an area that has adequate fresh air.
installing your dryer GAS REQUIREMENTS Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas.
ELECTRICAL REQUIREMENTS Wiring diagram is located on the plate below the control panel. • WARNING • 01 installing your dryer • Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
installing your dryer ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service.
CONNECTING THE INLET HOSE Method1 Do not overtighten, as it may damage the coupling. 5. Attach angled end of long hoses to fill the valve at the bottom of the dryer’s rear frame. Screw on coupling by hand until it is seated on fill valve connector. 6. Using pliers, tighten the coupling with an additional twothirds turn. Water Hose 01 installing your dryer The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1.
installing your dryer REPLACEMENT PARTS AND ACCESSORIES If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864). INSTALLATION Gather the required tools and parts before starting the installation. Read and follow the instructions provided with any tools listed here.
U.S. MODELS: IMPORTANT – All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If the 4-wire system is used, the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.
installing your dryer 6. Review Gas Requirements section. Remove the pipe thread protective cap. Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections. Pipe joint compound must be resistant to the action of any liquefied petroleum gas. Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4” (1.9 cm) female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer.
4-WIRE system connections 01 installing your dryer 1. Remove the center terminal block screw. 2. Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw. 3. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block. 4. Connect the other wires to the outer terminal block screws. Tighten screws. 5. Tighten the strain relief screws. 6.
installing your dryer DRYER EXHAUST TIPS Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 1. Make sure your dryer is installed properly so it exhausts air easily. Wall Dryer DUCT EHAUST 2. Use 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. TAPE DUCT 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely.
DOOR REVERSAL 8. Reinsert the screw in the other hole. 4. Remove a screw on the Frame Front 9. Reinsert the screw (Step 4) on the Frame Front 5. Remove the two screws on the opposite side of the door hinge. 10. Place the door on the other side and reattach it to the dryer. 6. Remove two screws from the holder lever. 11. Reattach the holder lever. 7. Remove a screw from the door hinge. 12. Reattach the screws in the remaing holes. WARNING 01 installing your dryer 1. Unplug the power cord. 2.
operating Instructions, tips OVERVIEW OF THE CONTROL PANEL 1 1 Cycle Selector 2 7 3 4 5 6 7 8 9 To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate. The Normal, Heavy Duty, Towels, Perm Press and Delicates cycles are Sensor Dry cycles. Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level (very dry to damp dry) is reached.
Digital Graphic Display 3 Dry Level Selection Button 4 Temp Selection Button 5 Time Selection Button 6 Signal Selection Button 02 operating Instructions, tips 2 The display window shows the estimated time remaining in the cycle after the Start/Pause button is pressed. The estimated time remaining may fluctuate as the cycle progresses. The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is in the cool-down phase, the Cooling light will illuminate.
operating Instructions, tips 7 Select Cycle Option Adjust Time – Time can be added or subtracted from the automatically set times in the Manual Dry cycles (Time Dry, Quick Dry, or Air Fluff cycles). To add or subtract time from the cycle, press the Adjust Time arrow pad up or down until the desired time is displayed. Wrinkle Prevent -Wrinkle Prevent provides approximately 90 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling.
DRUM LIGHT Lights the dryer drum while the dryer is running. Setting & releasing It can be set while your dryer is not only running but also when it is stopped. If you do not turn the Drum Light off 5 minutes after turning it on, the Drum Light is automatically turned off. CHANGING LANGUAGE You may change the language shown in the display from English to French or Spanish. Press and hold the Rack Dry and Wrinkle Prevent buttons for 3 seconds until the display changes.
operating Instructions, tips RACK DRY Installing the drying rack 1. Open the dryer door. 2. Position drying rack in tumbler, placing the front lip of the drying rack on the top of the lint filter. 3. Place the rear legs in the two recessed areas of the dryer’s back wall then push down the middle of the drying rack to fix. 4. Place the items to be dried on the rack, leaving space between them so air can circulate. 5. Close the dryer door. 6. Use the Time Dry cycle.
CLEAN THE LINT FILTER • • • After each load. To shorten drying time. To operate more energy efficiently. LOAD THE DRYER PROPERLY • • • • Place only one washload in your dryer at a time. Mixed loads of heavy and lightweight fabrics will dry differently, which may result in lightweight fabrics being dry while heavy fabrics remain damp at the end of a drying cycle. Add one or more similar items to your dryer when only one or two articles of clothing need drying.
care and cleaning CONTROL PANEL Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel. The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your dryer and wipe up any spills or overspray immediately. TUMBLER Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an allpurpose cleaner.
special laundry tips SPECIAL LAUNDRY TIPS Bedspreads & Comforters • • • Blankets • • Curtains & Draperies • • Follow the care label instructions or dry on the Normal cycle and High temperature. Make sure the item is thoroughly dry before using or storing. May require repositioning to ensure even drying. Use Normal cycle and dry only one blanket at a time for best tumbling action. Make sure the item is thoroughly dry before using or storing.
troubleshooting CHECK THESE POINTS IF YOUR DRYER… PROBLEM SOLUTION Doesn’t run. • • • • Make sure the door is latched shut. Be sure the power cord is plugged into a live electrical outlet. Check the home’s circuit breaker and fuses. Press the Start/Pause button again if the door is opened during the cycle. Doesn’t heat. • • • • • Check the home’s circuit breaker and fuses. Select a heat setting other than Air Fluff. On a gas dryer, check that the gas supply is on.
PROBLEM SOLUTION Shuts off before load is dry • • • • • • Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.
troubleshooting INFORMATION CODES Information codes may be displayed to help you better understand what is occurring with your Dryer. ERROR DISPLAY SOLUTION DISPLAY For any codes not listed above, call 1–800–726–7864 (1–800–SAMSUNG) 32_ troubleshooting DV448AEG-02555A-10_EN.
appendix FABRIC CARE CHART Wash Cycle Special Instructions Warning Symbols for Laundering Normal Line Dry/ Hang to Dry Do Not Wash Permanent Press / Wrinkle Resistant / Wrinkle Control Drip Dry Do Not Wring Gentle/Delicates Dry Flat Do Not Bleach Hand Wash Heat Setting Do Not Tumble Dry High No Steam (added to iron) Hot Medium Do Not Iron Warm Low Cold Any Heat Dry Clean No Heat/Air Do Not Dry Clean Water Temperature** Bleach Any Bleach (when needed) Iron-Dry or Steam Temperatu
appendix PROTECTING THE ENVIRONMENT This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. DECLARATION OF CONFORMITY This appliance complies with UL2158.
CYCLE CHART Default Cycle Wrinkle prevent Sensor dry level Time Time Time Time Normal High (Medium) Normal dry 44 min 39 min 5 min 90 min Heavy Duty High (No change) Normal dry 60 min 55 min 5 min 90 min Towels High (Medium) Normal dry 52 min 47 min 5 min 90 min Perm Press Medium (No change) Normal dry 34 min 24 min 10 min 90 min Delicates Low (No change) Normal dry 29 min 24 min 5 min 90 min Sanitize High (No change) Very dry (No change) 60 min 55 min 5 min 9
warranty SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
QUESTIONS OR COMMENTS? Country CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com MEXICO 01-800-SAMSUNG(726-7864) www.samsung.com Code No. DC68-02555A-10_EN DV448AEG-02555A-10_EN.
DV448AE* DV448AG* DV438AE* DV438AG* Secadora a gas y eléctrica Manual del usuario Este manual está impreso en papel 100% reciclado. imagina las posibilidades Gracias por adquirir este producto Samsung. Para que podamos brindarle un servicio más completo, registre su producto en www.samsung.com/register 1-800-SAMSUNG (726-7864) DV448AEG-02555A-10_MES.
características 1. Capacidad extra grande ¡Capacidades de ultra secado al alcance de la mano! Ahora puede secar cargas extra grandes. Nuestra secadora ultra grande, con 7,4 cu.ft. de capacidad, hace circular más aire entre su ropa, secándola más rápido, para obtener un resultado sin arrugas. 2. Ciclo Steam (vapor) Este ciclo rocía una pequeña cantidad de agua en el tambor de la secadora después de varios minutos de secado con calor.
instrucciones de seguridad Felicitaciones por la compra de la nueva secadora Samsung. Este manual contiene información importante acerca de la instalación, el uso y el cuidado del electrodoméstico. Lea detenidamente estas instrucciones a fi n de aprovechar al máximo los múltiples benefi cios y funciones de la secadora.
instrucciones de seguridad ADVERTENCIA ADVERTENCIA: Para reducir el riesgo de incendio, descargas eléctricas o lesiones físicas cuando usa este electrodoméstico, siga las instrucciones de seguridad básicas que fi guran a continuación: 1. Lea todas las instrucciones antes de usar este electrodoméstico. 2.
ADVERTENCIA - Riesgo de incendio • • • • La instalación de la secadora de ropa debe estar a cargo de un instalador califi cado. Instale la secadora de ropa según las instrucciones del fabricante y los códigos locales. No instale una secadora de ropa con materiales para ventilación de plástico fl exible. Si se instala un conducto de metal fl exible (tipo lámina metálica), debe ser de un tipo específi co identifi cado por el fabricante del electrodoméstico como adecuado para utilizar con secadoras de ropa.
instrucciones de seguridad No permita que los niños o las mascotas jueguen sobre el electrodoméstico, dentro de él o frente a él. Se requiere de supervisión cuando el electrodoméstico es utilizado cerca de niños y mascotas. Antes de desechar la secadora o de retirarla de servicio, quite la puerta del compartimiento de secado para evitar que los niños y las mascotas queden atrapados dentro de la secadora. No introduzca la mano en el electrodoméstico cuando el tambor esté en movimiento.
contenido 13 13 14 15 16 16 19 20 21 Herramientas necesarias para la instalación Consulte la sección Requisitos para el drenaje.
instalación de la secadora HERRAMIENTAS NECESARIAS PARA LA INSTALACIÓN Contrate a un profesional para instalar la secadora adecuadamente. En caso de que sea necesaria una visita del servicio técnico como consecuencia de una mala configuración, ajuste y conexión, se considerará responsabilidad del instalador. Si usted mismo instala la secadora, usted será el responsable. Asegúrese de tener todo lo necesario para realizar una instalación adecuada. 1. Se requiere un TOMACORRIENTE CON CONEXIÓN A TIERRA.
REQUISITOS PARA EL TENDIDO DE CONDUCTOS • • • • • • • • • • • • • • • • • 01 instalación de la secadora • Utilice un conducto de acero galvanizado rígido o de aluminio rígido, de 4 pulgadas (10,2 cm) de diámetro. No utilice un conducto de menor tamaño. Los conductos de más de 4 pulgadas (10,2 cm) de diámetro pueden ocasionar una mayor acumulación de pelusa. Periódicamente, debe retirar la pelusa acumulada.
instalación de la secadora Si la nueva secadora se está instalando dentro de un sistema de drenaje existente, debe asegurarse de que: • el sistema de drenaje cumpla con todos los códigos locales, estaduales y nacionales; • no se utilice un conducto flexible de plástico; • se controle y limpie toda la pelusa acumulada del interior del conducto existente; • el conducto no esté enroscado o aplastado; • el regulador de tiro de la tapa de drenaje se abra y se cierre sin inconvenientes.
INSTALACIÓN EN CASAS RODANTES 01 instalación de la secadora La instalación de la secadora en casas rodantes debe cumplir con la Norma de Construcción y Seguridad de Casas Fabricadas, Título 24 CFR, Parte 3280 [denominada anteriormente Norma Federal para la Construcción y la Seguridad de Casas Rodantes, Título 24, HUD (Parte 280), 1975] (para los Estados Unidos) o las Normas CSA Z240 (para Canadá).
instalación de la secadora REQUISITOS EN CUANTO AL GAS Utilice únicamente gas natural o gas LP (gas licuado de propano). LA INSTALACIÓN DEBE REALIZARSE EN CONFORMIDAD CON LOS CÓDIGOS LOCALES, O EN AUSENCIA DE ELLOS, CON EL CÓDIGO NACIONAL PARA GAS Y COMBUSTIBLES ANSI/ Z223.1, LA REVISIÓN MÁS RECIENTE (PARA LOS ESTADOS UNIDOS), O CON LOS CÓDIGOS DE INSTALACIÓN CAN/CGA-B149 (PARA CANADÁ). Las secadoras a gas están equipadas con un orificio para el quemador de modo que puedan ser utilizadas con gas natural.
REQUISITOS ELÉCTRICOS El diagrama del cableado se encuentra en la placa debajo del panel de control. • • • La conexión inadecuada del conductor de conexión a tierra del equipo puede generar una descarga eléctrica. Consulte a un electricista o técnico califi cado si le surgen dudas acerca de si la conexión a tierra de su secadora es correcta. No modifi que el enchufe provisto con la secadora; si no entra en el tomacorriente, solicite a un electricista califi cado que instale el tomacorriente adecuado.
instalación de la secadora CONEXIONES ELÉCTRICAS Antes de poner al electrodoméstico en funcionamiento o realizar pruebas, siga las instrucciones de conexión a tierra de la sección Conexión a tierra. Se recomienda que se destine un circuito derivado individual (o separado) sólo para la secadora. NO UTILICE UN CABLE PROLONGADOR. Modelos a gas – EE.UU. y Canadá Se requiere un servicio eléctrico aprobado de CA de 120 voltios, 60 Hz, con un fusible o disyuntor de 15 A. Modelos eléctricos – Sólo EE.UU.
CONEXIÓN DE LA MANGUERA DE ENTRADA Método 1 agua No ajuste demasiado ya que se puede dañar la unión. 5. Conecte el extremo angular de las mangueras largas para llenar la válvula en la parte inferior del armazón trasero de la secadora. Enrosque la unión a mano hasta que se asiente en el conector de la válvula de carga. 6. Ajuste la unión con dos tercios de giro adicionales utilizando la pinza.
instalación de la secadora REEMPLAZO DE LAS PIEZAS Y LOS ACCESORIOS Si es preciso reemplazar piezas o accesorios de la secadora, comuníquese con el distribuidor al que le compró la secadora o con el centro de atención al cliente de SAMSUNG al 1-800-SAMSUNG (726-7864). INSTALACIÓN Reúna las herramientas y piezas necesarias antes de comenzar la instalación. Lea y siga las instrucciones provistas con cualquier herramienta enumerada aquí.
MODELOS ESTADOUNIDENSES: IMPORTANTE: Todos los modelos estadounidenses fueron fabricados para una CONEXIÓN DE SISTEMAS DE 3 CABLES. El armazón de la secadora está conectado a tierra al conductor neutro del bloque de terminales. Se requiere una CONEXIÓN DE SISTEMAS DE 4 CABLES para las construcciones nuevas o remodeladas, las casas rodantes o si los códigos locales no permiten la conexión a tierra a través del neutro.
instalación de la secadora 6. Consulte la sección Requisitos en cuanto al gas. Retire la cubierta protectora de la rosca para tubos. Aplique compuesto de unión de tuberías o 1 1/2 vueltas aproximadamente de cinta de teflón en todas las conexiones roscadas. El compuesto de unión de tuberías utilizado debe ser resistente a la acción del gas licuado de petróleo. Conecte el suministro de gas a la secadora.
Conexiones de sistemas de 4 CABLES 01 instalación de la secadora 1. Retire el tornillo central del bloque de terminales. 2. Conecte el cable a tierra (verde o sin cubierta) del cable de alimentación al tornillo conductor a tierra externo. 3. Conecte el cable neutro (cable blanco o central) del cable de alimentación y el cable a tierra del electrodoméstico (verde con franjas amarillas) debajo del tornillo central del bloque de terminales. 4.
instalación de la secadora SUGERENCIAS ACERCA DEL DRENAJE DE LA SECADORA ADVERTENCIA Un conducto flexible de plástico o de un material que no sea el metal presenta un potencial riesgo de incendio. 1. Asegúrese de que su secadora esté instalada correctamente para que extraiga el aire fácilmente. Pared Secadora 2. Utilice un conducto de metal rígido, de 4” de diámetro. Coloque cinta en todas las uniones, incluso en la secadora. Nunca use tornillos que atrapen pelusa.
INVERSIÓN DE LA PUERTA 8. Vuelva a colocar los tornillos en los otros orificios. 4. Retire un tornillo del frente delantero. 9. Vuelva a colocar el tornillo (Paso 4) en el frente delantero. 5. Retire los dos tornillos del lado opuesto de la bisagra de la puerta. 10. Coloque la puerta sobre el lado contrario y vuelva a fijar a la secadora. 6. Retire los dos tornillos de la placa de apoyo. 11. Vuelva a conectar la placa de apoyo. 7. Retire un tornillo de la bisagra de la puerta. 12.
manual de instrucciones, sugerencias DESCRIPCIÓN GENERAL DEL PANEL DE CONTROL 1 1 Selector de ciclos 2 7 3 4 5 6 7 8 9 Paraseleccionar un ciclo, gire el disco Selector de ciclos hasta llegar al ciclo deseado. La luz del indicador junto al nombre del ciclo se iluminará. Los ciclos Normal (Normal), Heavy Duty (Servicio pesado), Towels (Toallas), Perm Press (Plancha permanente) y Delicates (Prendas delicadas) son ciclos Sensor Dry (Secado con sensor).
3 4 5 6 Pantalla gráfica digital Botón de selección Dry Level (Nivel de secado) Botón de selección Temp (Temperatura) Botón de selección Time (Tiempo) Botón de selección Signal (Señal) 02 manual de instrucciones, sugerencias 2 Lapantalla digital muestra el tiempo restante del ciclo calculado después de presionar el botón Start/Pause (Inicio/Pausa). El tiempo restante calculado puede fluctuar a medida que avance el ciclo.
manual de instrucciones, sugerencias 7 8 9 Opción de selección de ciclo Adjust Time (Ajustar tiempo): se puede agregar o restar tiempo a los tiempos configurados automáticamente en los ciclos de Manual Dry (Secado manual) (ciclos Time Dry (Secado con temporizador), Quick Dry (Secado rápido), o Air Fluff (Secado a temperatura ambiente). Para agregar o restar tiempo al ciclo, presione la tecla Adjust Time (Ajustar tiempo) con la flecha hacia arriba o hacia abajo hasta que aparezca el tiempo deseado.
LUZ DEL TAMBOR Enciende el tambor de la secadora mientras se realiza el secado. Si desea configurar o liberar esta función, presione simultáneamente los botones Dry Level (Nivel de secado) y Temp. (Temperatura). Puede configurarse no sólo cuando su secadora está en funcionamiento sino también cuando está detenida. Si no apaga la luz del tambor 5 minutos después de que se encienda, la luz del tambor se apaga automáticamente.
manual de instrucciones, sugerencias RACK DRY (SECADO EN ESTANTE) Instalación del estante de secado 1. Abra la puerta de la secadora. 2. Coloque el estante de secado en el tambor, con el borde superior del estante de secado encima del filtro para pelusas. 3. Coloque las patas traseras en las dos áreas empotradas de la pared trasera de la secadora y luego empuje hacia abajo en el centro del estante de secado para ajustar. 4.
LIMPIE EL FILTRO PARA PELUSAS Después de cada carga. Para reducir el tiempo de secado. Para hacer uso de la energía con mayor eficacia. No haga funcionar la secadora sin el filtro para pelusas colocado. CARGUE LA SECADORA DE MANERA ADECUADA • • • • Coloque sólo una carga de ropa en la secadora por vez.
cuidado y limpieza PANEL DE CONTROL Limpie con un paño suave y húmedo. No utilice sustancias abrasivas. No rocíe el panel directamente con limpiadores en aerosol. El acabado del panel de control puede dañarse a causa de algunos productos removedores de suciedad y manchas de tratamiento previo al lavado. Aplique dichos productos lejos de la secadora y limpie el líquido derramado o el rocío inmediatamente.
sugerencias para prendas especiales SUGERENCIAS PARA PRENDAS ESPECIALES Cubrecamas y edredones • • • Frazadas • • Cortinas y paños de tela • • Siga las instrucciones de la etiqueta o seque en el ciclo Normal (Normal) y con temperatura High (Alta). Asegúrese de que la prenda esté completamente seca antes de usarla o guardarla. Tal vez deba volver a colocarla para garantizar un secado uniforme.
guía de solución de problemas CONTROLE ESTOS PUNTOS SI SU SECADORA… PROBLEMA SOLUCIÓN No funciona. • • • • No calienta. • • • • • No seca. • • • • • • • • • Hace ruido. • • • • Asegúrese de que la puerta esté cerrada con traba. Asegúrese de que el cable de alimentación esté enchufado a un tomacorriente que funcione. Controle los disyuntores y fusibles de la casa. Presione el botón Start/Pause (Inicio/Pausa) nuevamente si la puerta se abre durante el ciclo.
SOLUCIÓN No seca de manera uniforme. • • Tiene olor. • • Se apaga antes de que la carga esté seca • • Pelusa en las prendas • • • • Es posible que las costuras, los bolsillos y otras áreas resistentes similares no se sequen por completo cuando el resto de la carga ha llegado al nivel de secado seleccionado. Esto es normal. Seleccione la opción Very Dry (Muy seco) si lo desea.
guía de solución de problemas CÓDIGOS DE INFORMACIÓN Pueden aparecer códigos de información para ayudarle a comprender mejor qué ocurre con la secadora. PANTALLA DE ERROR PANTALLA DE SOLUCIÓN Para los códigos que no figuran más arriba, llame al 1–800–726–7864 (1–800–SAMSUNG). 32_ guía de solución de problemas DV448AEG-02555A-10_MES.
apéndice TABLA DE INDICACIONES DEL TEJIDO Ciclo de lavado Instrucciones especiales Símbolos de advertencia para el lavado Normal Secar colgado / tender No lavar Plancha permanente / Antiarrugas / Control de arrugas Colgar para que escurra No retorcer Prendas suaves / delicadas Secar en posición horizontal No usar lejía Lavado a mano Secado con calor No secar en secadora High (Alta) Sin vapor (agregado a la plancha) Caliente Medio No planchar Cálida Bajo Fría Cualquier calor Limpiar
apéndice PROTECCIÓN DEL MEDIO AMBIENTE Este electrodoméstico se fabrica con materiales reciclables. Si decide deshacerse de este electrodoméstico, siga la normativa local relacionada con la eliminación de desechos. Corte el cable de alimentación para que el electrodoméstico no pueda conectarse a una fuente de alimentación. Quite la puerta para que los animales y los niños pequeños no puedan quedar atrapados dentro del electrodoméstico.
TABLA DE CICLOS Predeterminado Ciclo Manual Dry (Secado manual) Steam Cycles (Ciclos de vapor) Enfriar Prevención de arrugas Control de temp. Nivel de secado con sensor Tiempo Tiempo Tiempo Tiempo Normal High (Medium) (Alta (Media)) Normal dry (Secado normal) 44 min. 39 min. 5 min. 90 min. Heavy Duty (Servicio pesado) High (No change) (Alta (Sin cambios)) Normal dry (Secado normal) 60 min. 55 min. 5 min. 90 min.
garantía SECADORA SAMSUNG GARANTÍA LIMITADA PARA EL COMPRADOR ORIGINAL El presente producto de la marca SAMSUNG, tal como lo provee y distribuye SAMSUNG ELECTRONICS AMERICA, INC.
EXCEPTO LO ESTABLECIDO EN EL PRESENTE, NO EXISTEN GARANTÍAS SOBRE ESTE PRODUCTO, YA SEAN EXPRESAS O TÁCITAS, Y SAMSUNG DESCONOCE TODAS LAS GARANTÍAS QUE INCLUYEN, AUNQUE NO EN CARÁCTER TAXATIVO, CUALQUIER GARANTÍA TÁCITA DE QUE EL PRODUCTO SE ENCUENTRA EN CONDICIONES APTAS PARA LA VENTA, DE DEFRAUDACIÓN DE DERECHOS O DE QUE EL PRODUCTO SE ADECUA A LOS FINES ESPECÍFICOS PARA LOS CUALES SE ADQUIERE.
¿TIENE PREGUNTAS O COMENTARIOS? País LLAME AL O VISÍTENOS EN LÍNEA EN U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com MEXICO 01-800-SAMSUNG(726-7864) www.samsung.com Número de código DC68-02555A-10_MES DV448AEG-02555A-10_MES.