DV5471A* DV5451A* Gas and Electric Dryer user manual This manual is made with 100% recycled paper. imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service or accessory parts, please register your product at or contact www.samsung.com/register 1-800-SAMSUNG (726-7864) DV5471AE-03022A-03_EN.
features 1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultralarge 7.4cu.ft(DV5471A*), 7.3cu.ft(DV5451A*) capacity dryer circulates more air through your clothes, drying them faster, for a wrinkle-free result. 2. Steam Cycle This cycle sprays a small amount of water into the dryer drum after several minutes of tumbling with heat.
7. Easy Reversible Door The direction of our reversible door can be changed easily. 8. 4-way Vent (electric model only) You can install the exhaust vent in the following four (4) positions: back, either side, bottom. Features _3 DV5471AE-03022A-03_EN.
safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur.
WARNING WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3.
safety instructions WARNING - Risk of Fire • • • • WARNING Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer’s instructions and local codes. Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets. Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside. Do not reach into the appliance when the drum is moving. Do not install or store this appliance where it will be exposed to the weather. Do not tamper with controls.
contents 15 15 16 17 19 20 22 23 Unpacking your dryer Basic requirments Ducting requirements Important to installer Location considerations Alcove or closet installation Mobile home installation Exhausting Gas requirements Commonwealth of Massachusetts installation instructions Electrical requirements Grounding Electrical connections Installation - General procedure Final installation checklist Connecting the inlet hose Dryer Exhaust Tips Door Reversal 25 28 28 29 30 30 30 Overview of the control panel
installing your dryer UNPACKING YOUR DRYER WARNING Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene, etc.) well out of childrens’ reach Control panel [ BACK ] Top Cover 01 installing your dryer Unpack your Dryer and inspect it for shipping damage. Make sure you have received all of the items shown below. If your Dryer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (726-7864).
installing your dryer Tools needed Pliers Cutting knife Pipe wrench (gas only) Nut drivers Level Phillips Screwdriver Duct tape Wrench BASIC REQUIRMENTS Make sure you have everything necessary for proper installation • A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. • A POWER CORD for electric dryers (except in Canada). • GAS LINES (if installing a gas dryer). The gas lines must meet national and local codes.
DUCTING REQUIREMENTS • • • • • • • • • • • • • • • • • 01 installing your dryer • Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation. Lint accumulation should be cleaned regularly. If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall.
installing your dryer If the new dryer is being installed into an existing exhaust system, you must make sure: • The exhaust system meets all local, state, and national codes. • That a flexible plastic duct is not used. • To Inspect and clean all lint buildup from inside the existing duct. • The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
MOBILE HOME INSTALLATION 01 installing your dryer The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a dryer in a mobile home, you must make provisions for anchoring the dryer to the floor.
installing your dryer GAS REQUIREMENTS Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas.
ELECTRICAL REQUIREMENTS Wiring diagram is located on the plate below the control panel or frame back. • • • Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
installing your dryer ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service.
INSTALLATION - GENERAL PROCEDURE For proper installation, we recommend that you hire a qualified installer. Read these instructions completely before you begin the installation. To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it lies across both cushion-tops. Push the dryer so that it is near its final location. Set your dryer upright. Leave enough room around the dryer so you can attach the duct work, power cord, etc. 2.
installing your dryer 6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below. 7. Three Wire system instructions: A. External ground connector B. Neutral grounding wire (green/yellow) C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. ¾” (1.9 cm) UL-listed strain relief 1. Loosen or remove the center terminal block screw. 2.
U.S. MODELS: IMPORTANT – All U.S. models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block. Remove the terminal block cover plate.
installing your dryer CONNECTING THE INLET HOSE Method1 - Using the Y Connector and Long Hose The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. Turn off the cold water faucet. 2. If you have a washer water hose attached to the cold water Y-Connector faucet, unscrew and remove the hose. 3. If space permits, attach the brass female end of the “Y”connector to the cold water faucet. Turn by hand until tight. Water Hose 4.
Method2 - Using the Short Hose, Long Hose, and Y Connector Do not overtighten. You can damage the coupling. 5. Attach the ‘Y” connector to the stainless male end of the small hose. Screw on the coupling by hand until it is tight. 6. Using pliers, tighten the coupling with an additional two thirds turn. 01 installing your dryer The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.
installing your dryer DRYER EXHAUST TIPS Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 1. Make sure your dryer is installed properly so it exhausts air easily. Wall Dryer DUCT EXHAUST 2. Use 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. TAPE DUCT 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely.
DOOR REVERSAL 11. Turn the Holder-Glass upside down and remove the 8 screws. 4. Remove the two screws from the lever-holder and then remove the screw on the opposite side from the lever-holder. 5. Assemble the lever-holder using the screws that were removed from the lever-holder-in Step 4 and then fasten the screws marked by the circle in the figure to the opposite side from the lever-holder. 12. Remove 2 SupportHinges and the HingeDoor 6. Remove the two screws from the Frame-Front. 7.
installing your dryer 18. Install the 2 Cushion Cover(F)s that you removed in Step 8. 20. Remove the CushionCover(F). Failure to do so may result in the malfunction. Store the removed Cushion-Cover(F) in a safe location. When you change the direction in which the door opens so that the door opens to the left, you have to install the Cushion-Cover(F) onto the door again. 19. Install the Lever-Door onto the other side. 21.
operating instructions, tips OVERVIEW OF THE CONTROL PANEL 2 1 Digital Graphic Display 2 Select Cycle Option 3 4 5 6 7 8 02 operating instructions, tips 1 The display window shows the estimated time remaining in the cycle after you have pressed the Start/Pause button. The estimated time remaining may fl uctuate as the cycle progresses. The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is in the cool-down phase, the Cooling light will illuminate.
operating instructions, tips To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate. The Nomal, Heavy Duty, Perm Press, Bedding, Towels, Delicates, Wool cycles are Sensor Dry cycles. Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the load reaches the dryness level you have selected with the Dry Level Selection Button (see below). Normal – Use this cycle to dry loads of cotton, underwear, and linen.
5 Temp Selection Button 6 Time Selection Button 7 Start/Pause selection button Press to pause and restart programs. 8 Power button Press once to turn your dryer on, press again to turn it off. If you turn your dryer on and do not touch any buttons for 10 minutes, the power automatically turns off. 02 operating instructions, tips To select the temperature for the load, press the Temp button. An indicator light will illuminate next to the temperature you selected.
operating instructions, tips CHILD LOCK A function to prevent children from playing with your dryer. Setting/Releasing If you want to set or release the Child Lock, press the Temp. and Time buttons simultaneously for 3 seconds. Child Lock Details - You can set Child Lock while your dryer is running. Once you turn Child Lock on, no button, except for the Power button, will respond until you release the Child Lock function. The Child Lock indicator will be lit.
RACK DRY Installing the drying rack 02 operating instructions, tips 1. Open the dryer door. 2. Place the Drying Rack inside the product, and then align the holes of the filter handle of the Drying Rack to the front projections. 3. Place the rear legs in the two recessed areas of the dryer’s back wall, and then push down the middle of the drying rack to fix it in place. 4. Place the items to be dried on the rack, leaving space between them so air can circulate. 5. Close the dryer door. 6.
operating instructions, tips CLEAN THE LINT FILTER • • • After each load. To shorten drying time. To operate more energy efficiently. Do not operate your dryer without the lint filter in place. Frame Front Filter Door LOAD THE DRYER PROPERLY • • • • Place only one washload in your dryer at a time. In mixed loads, heavy and lightweight fabrics will dry differently. This may result in lightweight fabrics being dry while heavy fabrics remain damp at the end of a drying cycle.
care and cleaning CONTROL PANEL TUMBLER Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an allpurpose cleaner. Tumble old towels or rags to remove any excess stain or cleaning substance. Once these steps are followed, stains may still be visible, but should not transfer to subsequent loads. 03 care and cleaning Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel.
special laundry tips Special laundry tips Please follow the care label or manufacturer’s instructions for drying special items. If care label instructions are not available, use the following information as a guide. Bedspreads & Comforters • • • Follow the care label instructions or dry using the Bedding cycle. Make sure the item is thoroughly dry before using or storing. May require repositioning to ensure even drying.
troubleshooting CHECK THESE POINTS IF YOUR DRYER… SOLUTION Doesn’t run. • • • • Make sure the door is latched shut. Be sure the power cord is plugged into a live electrical outlet. Check your home’s circuit breakers or fuses. Press the Start/Pause button again if the door is opened during the cycle. Doesn’t heat. • • • • • Check your home’s circuit breakers or fuses. Select a heat setting other than Air Fluff. On a gas dryer, check that the gas supply is on. Clean the lint filter and exhaust duct.
troubleshooting PROBLEM SOLUTION Shuts off before load is dry • The dryer load is too small. Add more items or a few towels and restart the cycle. The dryer load is too large. Remove some items and restart the dryer. • Lint on clothes • Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.
appendix FABRIC CARE CHART Wash Cycle Special Instructions Warning Symbols for Laundering Normal Line Dry/ Hang to Dry Do Not Wash Permanent Press / Wrinkle Resistant / Wrinkle Control Drip Dry Do Not Wring Gentle/Delicates Dry Flat Do Not Bleach Hand Wash Heat Setting Do Not Tumble Dry High No Steam (added to iron) Hot Medium Do Not Iron Warm Low Cold Any Heat Dry Clean No Heat/Air Do Not Dry Clean Water Temperature** Bleach Any Bleach (when needed) Iron-Dry or Steam Temperatu
appendix PROTECTING THE ENVIRONMENT This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. DECLARATION OF CONFORMITY This appliance complies with UL2158. SPECIFICATIONS C D A B TYPE DIMENSIONS FRONT LOADING DRYER Div A. Height 44.
CYCLE CHART Elec. Dryer Type Default (Initial temp. 20.1~30.
warranty SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
Except as set forth herein, there are no warranties on this product either express or implied, and samsung disclaims all warranties including, but not limited to, any implied warranties of merchantability, infringement or fitness for a particular purpose. No warranty or guarantee given by any person, firm, or corporation with respect to this product shall be binding on samsung.
QUESTIONS OR COMMENTS? Country CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com MEXICO 01-800-SAMSUNG(726-7864) www.samsung.com Code No. DC68-03022A-03_EN DV5471AE-03022A-03_EN.
DV5471A* DV5451A* Secadora a gas y eléctrica manual del usuario Este manual está impreso en papel 100% reciclado. imagine las posibilidades Gracias por adquirir este producto Samsung. Para que podamos brindarle un servicio más completo, registre su producto en www.samsung.com/register 1-800-SAMSUNG (726-7864) DV5471AE_03022A-03_MES.
características 1. Capacidad extra grande ¡Las capacidades de secado ultra al alcance de la mano! Ahora puede secar cargas extra grandes. Nuestra secadora ultra grande, con 7.4cu.ft(DV5471A*), 7.3cu.ft(DV5451A*) de capacidad, hace circular más aire entre su ropa, secándola más rápido, para obtener un resultado sin arrugas. 2. Ciclo de vapor Este ciclo rocía una pequeña cantidad de agua en el tambor de la secadora después de varios minutos de secado con calor.
7. Puerta fácilmente reversible La dirección de la puerta reversible puede modificarse fácilmente. 8. Ventilación de 4 direcciones (modelo eléctrico solamente: DV5471AE*, DV5451AE*) Puede instalar la ventilación del drenaje en las siguientes cuatro (4) posiciones: atrás, en cualquiera de los laterales, en la parte inferior. características _3 DV5471AE_03022A-03_MES.
instrucciones de seguridad Felicitaciones por la compra de la nueva secadora Samsung. Este manual contiene información importante acerca de la instalación, el uso y el cuidado del electrodoméstico. Lea detenidamente estas instrucciones a fin de aprovechar al máximo los múltiples beneficios y funciones de la secadora.
ADVERTENCIA ADVERTENCIA: Para reducir el riesgo de incendio, descargas eléctricas o lesiones físicas cuando usa este electrodoméstico, siga las instrucciones de seguridad básicas que figuran a continuación: 1. Lea todas las instrucciones antes de usar este electrodoméstico. 2.
instrucciones de seguridad ADVERTENCIA - Riesgo de incendio • • • • La instalación de la secadora de ropa debe estar a cargo de un instalador calificado. Instale la secadora de ropa según las instrucciones del fabricante y los códigos locales. No instale una secadora de ropa con materiales para ventilación de plástico flexible.
No permita que los niños o las mascotas jueguen sobre el electrodoméstico, dentro de él o frente a él. Se requiere de supervisión cuando el electrodoméstico es utilizado cerca de niños y mascotas. Antes de desechar la secadora o de retirarla de servicio, quite la puerta del compartimiento de secado para evitar que los niños y las mascotas queden atrapados dentro de la secadora. No introduzca la mano en el electrodoméstico cuando el tambor esté en movimiento.
contenido INSTALACIÓN DE LA SECADORA 23 Desembalaje de la secadora Requisitos básicos Requisitos para el tendido de conductos Importante para el instalador Consideraciones acerca de la ubicación Instalación del electrodoméstico en un gabinete o en un hueco Instalación en casas rodantes Drenaje Requisitos en cuanto al gas Instrucciones de instalación de la comunidad de Massachusetts Requisitos eléctricos Conexión a tierra Conexiones eléctricas Instalación - procedimiento general Lista de verificación final d
instalación de la secadora DESEMBALAJE DE LA SECADORA ADVERTENCIA Los materiales de embalaje pueden ser peligrosos para los niños. Mantenga todos los materiales de embalaje (bolsas de plástico, poliestireno, etc.) lejos del alcance de los niños. Panel de control [ PARTE POSTERIOR ] Cubierta superior 01 instalación de la secadora Desembale la secadora e inspecciónela para controlar que no se hayan producido daños durante el transporte.
instalación de la secadora Herramientas necesarias Pinzas Cúter Llave inglesa para tuberías (sólo de gas) Llave de tuercas Nivel Destornillador Phillips Cinta para conductos Llave inglesa REQUISITOS BÁSICOS Asegúrese de tener todo lo necesario para realizar una instalación adecuada • Se requiere un TOMACORRIENTE CON CONEXIÓN A TIERRA. Consulte la sección Requisitos eléctricos. • Un CABLE DE ALIMENTACIÓN para las secadoras eléctricas (excepto en Canadá).
REQUISITOS PARA EL TENDIDO DE CONDUCTOS • • • • • • • • • • • • • • • • • 01 instalación de la secadora • Utilice un conducto de acero galvanizado rígido o de aluminio rígido, de 4 pulgadas (10,2 cm) de diámetro. No utilice un conducto de menor tamaño. Los conductos de más de 4 pulgadas (10,2 cm) de diámetro pueden causar una mayor acumulación de pelusa. Periódicamente, debe retirar la pelusa acumulada.
instalación de la secadora Si la nueva secadora se está instalando dentro de un sistema de drenaje existente, debe asegurarse de que: • El sistema de drenaje cumpla con todos los códigos locales, estaduales y nacionales; • No se utilice un conducto flexible de plástico; • Se controle y limpie toda la pelusa acumulada del interior del conducto existente; • Compruebe que el conducto no esté enroscado o aplastado; • El regulador de tiro de la tapa de drenaje se abra y se cierre sin inconvenientes.
INSTALACIÓN EN CASAS RODANTES 01 instalación de la secadora La instalación de la secadora en casas rodantes debe cumplir con la Norma de Construcción y Seguridad de Casas Fabricadas, Título 24 CFR, Parte 3280 [denominada anteriormente Norma Federal para la Construcción y la Seguridad de Casas Rodantes, Título 24, HUD (Parte 280), 1975] (para los Estados Unidos) o las Normas CSA Z240 (para Canadá). Cuando se instala una secadora en una casa rodante, debe tener la precaución de asegurar la secadora al piso.
instalación de la secadora REQUISITOS EN CUANTO AL GAS Utilice únicamente gas natural o gas LP (gas licuado de propano). LA INSTALACIÓN DEBE REALIZARSE EN CONFORMIDAD CON LOS CÓDIGOS LOCALES, O EN AUSENCIA DE ELLOS, CON EL CÓDIGO NACIONAL PARA GAS Y COMBUSTIBLES ANSI/Z223.1, LA REVISIÓN MÁS RECIENTE (PARA LOS ESTADOS UNIDOS), O CON LOS CÓDIGOS DE INSTALACIÓN CAN/CGA-B149 (PARA CANADÁ). Las secadoras a gas están equipadas con un orificio para el quemador de modo que puedan ser utilizadas con gas natural.
REQUISITOS ELÉCTRICOS El diagrama del cableado se encuentra en la placa debajo del panel de control o en la espalda del marco. • • • La conexión inadecuada del conductor de conexión a tierra del equipo puede generar una descarga eléctrica. Consulte a un electricista o técnico calificado si le surgen dudas acerca de si la conexión a tierra de su secadora es correcta.
instalación de la secadora CONEXIONES ELÉCTRICAS Antes de poner al electrodoméstico en funcionamiento o realizar pruebas, siga las instrucciones de conexión a tierra de la sección Conexión a tierra. Se recomienda que se destine un circuito derivado individual (o separado) sólo para la secadora. NO UTILICE UN CABLE PROLONGADOR. Modelos a gas – EE.UU. y Canadá Se requiere un servicio eléctrico aprobado de CA de 120 voltios, 60 Hz, con un fusible o disyuntor de 15 A. Modelos eléctricos – Sólo EE.UU.
INSTALACIÓN - PROCEDIMIENTO GENERAL Para realizar una instalación adecuada, recomendamos contratar a un instalador calificado. Lea estas instrucciones en su totalidad antes de iniciar la instalación. Para mover la secadora con facilidad, coloque dos de las protecciones superiores de cartón en el piso. Incline la secadora hacia uno de los laterales, de modo tal que quede atravesando ambas protecciones. Empuje la secadora de modo que quede cerca de su ubicación definitiva.
instalación de la secadora 6. Consulte la sección Requisitos Eléctricos, luego siga las instrucciones para conexión de sistemas de 3 cables (Paso 7) o las instrucciones para el sistema de 4 cables (Paso 8) a continuación. 7. Instrucciones para el sistema de tres cables: A. Conector a tierra externo B. Cable a tierra neutro (verde/amarillo) C. Tornillo central de color plateado del bloque de terminales D. Cable neutro (cable blanco o central) E.
MODELOS ESTADOUNIDENSES: IMPORTANTE – Todos los modelos estadounidenses están diseñados para una CONEXIÓN DE SISTEMAS DE 3 CABLES. El armazón de la secadora está conectado a tierra al conductor neutro del bloque de terminales. Se requiere una CONEXIÓN DE SISTEMAS DE 4 CABLES para las construcciones nuevas o remodeladas, las casas rodantes o si los códigos locales no permiten la conexión a tierra a través del neutro.
instalación de la secadora CONEXIÓN DE LA MANGUERA DE ENTRADA Método1 - Uso del conector en forma de "Y" y manguera larga La secadora debe conectarse a la llave de agua fría mediante las nuevas mangueras de entrada. No utilice mangueras viejas. 1. Cierre la llave de agua fría. 2. Si tiene una manguera de agua de la lavadora conectada a Conector Y la llave de agua fría, desatornille y quite la manguera. 3.
Método2 - Uso de la manguera corta, la manguera larga y el conector en forma de "Y" Manguera larga No la ajuste en exceso. Puede dañar la unión. 01 instalación de la secadora La secadora debe conectarse a la llave de agua fría mediante las nuevas mangueras de entrada. No utilice mangueras viejas. Si el conector en forma de "Y" no puede conectarse directamente a la llave de agua fría, debe utilizar la manguera corta. 1. Cierre la llave de agua fría. Manguera corta 2.
instalación de la secadora SUGERENCIAS ACERCA DEL DRENAJE DE LA SECADORA ADVERTENCIA Un conducto flexible de plástico o de un material que no sea el metal presenta un potencial riesgo de incendio. 1. Asegúrese de que su secadora esté instalada correctamente para que extraiga el aire fácilmente. Pared Secadora 2. Utilice un conducto de metal rígido, de 4” de diámetro. Coloque cinta en todas las uniones, incluso en la secadora. Nunca use tornillos que atrapen pelusa.
INVERSIÓN DE LA PUERTA 11. Voltee de cabeza la titular de vidrio y retire los 8 tornillos. 4. Retire los dos tornillos del cierre de la placa de apoyo y, luego, retire el tornillo del lado opuesto de la placa de apoyo. 5. Monte la placa de apoyo utilizando los tornillos retirados de la placa de apoyo en el paso 4 y apriete el tornillo marcado por el círculo en la figura en el lado opuesto de la placa de apoyo. 12. Retire el soporte de la bisagra y 2 las bisagras. 6.
instalación de la secadora 18. Instale las 2 protecciones de la cubierta(F) que ha retirado en el paso 8. 20. Retire la protección de la cubierta (F). De no hacerlo puede resultar en un mal funcionamiento. Guarde la protección de la cubierta (F) en un lugar seguro. Cuando cambie la dirección de la puerta para que se abra hacia la izquierda, debe montar de nuevo la protección de la cubierta (F) en la puerta. 19. Instale el cierre de la puerta en el lado opuesto. 21.
manual de instrucciones, sugerencias DESCRIPCIÓN GENERAL DEL PANEL DE CONTROL 2 1 Pantalla gráfica digital 2 Opción de selección de ciclo 3 4 5 6 7 8 02 manual de instrucciones, sugerencias 1 La pantalla digital muestra el tiempo restante del ciclo calculado después de presionar el botón Start/Pause (Inicio/Pausa). El tiempo restante calculado puede fluctuar a medida que avance el ciclo. Se iluminará la luz de Drying (Secar) y se mantendrá iluminada hasta que se haya cumplido el ciclo.
manual de instrucciones, sugerencias Esta función sólo puede seleccionarse en el ciclo Sensor Dry (Secado con sensor) y el nivel de secado sólo puede seleccionarse desde Normal Dry (Secado normal), More Dry (Más seco) y Very Dry (Muy seco). Signal (Señal) – Cuando el ciclo haya finalizado, se escuchará una señal sonora. Cuando selecciona la opción Wrinkle Prevent (Prevención de arrugas), la señal sonora sonará en forma intermitente.
4 Botón de selección Nivel de secado 5 Botón de selección Temp 6 Botón de selección Tiempo 7 Botón de selección Inicio/ Pausa Presiónelo para detener y reiniciar los programas. 8 Botón Encendido Presiónelo una vez para encender la secadora y presiónelo nuevamente para apagarla. Si enciende su secadora y no toca ningún botón durante 10 minutos, se apagará automáticamente.
manual de instrucciones, sugerencias SEGURO PARA NIÑOS Una función para evitar que los niños jueguen con la secadora. Configuración/Liberación Si desea configurar o liberar esta función, presione simultáneamente los botones Temp. (Temp.) y Time (Tiempo) durante 3 segundos. Detalles del Seguro para niños - Puede configurar el Seguro para niños mientras su secadora está en funcionamiento.
RACK DRY (SECADO EN ESTANTE) Instalación del estante de secado Estante de secado 02 manual de instrucciones, sugerencias 1. Abra la puerta de la secadora. 2. Coloque el estante de secado dentro del producto y luego alinee los orificios de la tapa del filtro con la parte frontal sobresaliente. 3. Coloque las patas traseras en las dos áreas empotradas de la pared trasera de la secadora y luego empuje hacia abajo en el centro del estante de secado para ajustarlo en su lugar. 4.
manual de instrucciones, sugerencias LIMPIE EL FILTRO PARA PELUSAS • • • Después de cada carga. Para reducir el tiempo de secado. Para hacer uso de la energía con mayor eficacia. No haga funcionar la secadora sin el filtro para pelusas colocado. Marco delantero Filtro Puerta CARGUE LA SECADORA DE MANERA ADECUADA • • • • Coloque sólo una carga de ropa en la secadora por vez. En cargas mixtas, las telas pesadas y livianas se secan en forma diferente.
cuidado y limpieza PANEL DE CONTROL TAMBOR Elimine todas las manchas, tales como las de crayón, tinta o tintura de la tela (proveniente de artículos nuevos, tales como toallas o jeans) con un limpiador común. Posteriormente, seque las toallas o prendas viejas para eliminar todo exceso de manchas o solución de limpieza. Una vez que se hayan seguido estos pasos, es posible que las manchas aún sean visibles, pero no se transferirán a las cargas subsiguientes.
sugerencias para prendas especiales Sugerencias para prendas especiales Siga las instrucciones del fabricante o de la etiqueta de indicaciones para secar prendas especiales. Si no se dispone de etiquetas con indicaciones, use la siguiente información como guía. Cubrecamas y edredones • • • Ropa de cama • • Cortinas y paños de tela • • Siga las instrucciones de la etiqueta con indicaciones o seque usando el ciclo Bedding (ropa de cama).
guía de solución de problemas CONTROLE ESTOS PUNTOS SI SU SECADORA... SOLUCIÓN No funciona. • • • • No calienta. • • • • • No seca. • • • • • • • • • Hace ruido. • • • • No seca de manera uniforme. • • Tiene olor. • • Asegúrese de que la puerta esté cerrada con traba. Asegúrese de que el cable de alimentación esté enchufado a un tomacorriente que funcione. Controle los disyuntores o fusibles de su casa.
guía de solución de problemas PROBLEMA SOLUCIÓN Se apaga antes de que la carga esté seca • • Pelusa en las prendas • • • • La carga de la secadora es demasiado pequeña. Agregue más prendas o algunas toallas y reinicie el ciclo. La carga de la secadora es demasiado grande. Retire algunas prendas y vuelva poner en funcionamiento la secadora. Limpie el filtro para pelusas antes de cada carga.
apéndice TABLA DE INDICACIONES SOBRE LA TELA Ciclo de lavado Instrucciones especiales Símbolos de advertencia para el lavado Normal (Normal) Secar colgado/tender No lavar Planchado permanente / Antiarrugas / Control de arrugas Colgar para que escurra No retorcer Prendas suaves / delicadas Secar en posición horizontal No usar lejía Lavado a mano Secado con calor No secar en secadora Alto Sin vapor (agregado a la plancha) Caliente Medium (Mediana) No planchar Tibia/Tibia Bajo Fría Cual
apéndice PROTECCIÓN DEL MEDIO AMBIENTE Este electrodoméstico se fabrica con materiales reciclables. Si decide desechar este electrodoméstico, siga la normativa local relacionada con la eliminación de desechos. Corte el cable de alimentación para que el electrodoméstico no pueda conectarse a una fuente de alimentación. Quite la puerta para que los animales y los niños pequeños no puedan quedar atrapados dentro del electrodoméstico. DECLARACIÓN DE CONFORMIDAD Este electrodoméstico cumple con la norma UL2158.
TABLA DE CICLOS Tipo de secadora eléctrica Predeterminado (temperatura inicial 21.0~30.0° C) Ciclo Control temp.
garantía SECADORA SAMSUNG GARANTÍA LIMITADA PARA EL COMPRADOR ORIGINAL El presente producto de la marca SAMSUNG, tal como lo provee y distribuye SAMSUNG ELECTRONICS AMERICA, INC.
Excepto lo establecido en el presente, no existen garantías sobre este producto, ya sean expresas o tácitas, y samsung desconoce todas las garantías que incluyen, aunque no en carácter taxativo, cualquier garantía tácita de que el producto se encuentra en condiciones aptas para la venta, de defraudación de derechos o de que el producto se adecua a los fines específicos para los cuales se adquiere.
¿TIENE PREGUNTAS O COMENTARIOS? País LLAME AL O VISÍTENOS EN LÍNEA EN U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com MEXICO 01-800-SAMSUNG (726-7864) www.samsung.com N.º de código: DC68-03022A-03_MES DV5471AE_03022A-03_MES.