Imagine the possibilities Thank you f@"purchasing this Samsung p_'oduct.
INSTALLING YOUR DRYER /' / 7 7 8 9 9 9 11 12 12 Unpacking your dryer Basic requirments Ducting requirements Important to installer Location considerations Alcove or closet installation Exhausting Gas requirements Commonwealth of Massachusetts installation instructions 13 13 14 Electrical requirements Grounding Electrical connections 15 18 18 19 20 Installation - General procedure Connecting the Inlet Hose Final installation check list Dryer Exhaust Tips Door Reversal OPERATING INSTRUCTIONS, TIPS
Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer's many benefits and features. WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur.
A WARNING WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3.
WARNING ,, ,, -- Risk of Fire Clothes dryer installationmust be performed by a qualified installer. Install the clothes dryer according to the manufacturer's instructions and local codes. Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint.
Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets. Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside. Do not reach into the appliance when the drum is moving. Do not install or store this appliance where it will be exposed to the weather. Do not tamper with controls.
UNPACKING YOUR DRYER Unpack your dryer and Inspect it for shipping damage. Make sure you have received all of the items shown below. If your dryer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (726-7864). To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer. Z_ Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene, ....... etc.) well out of children's reach.
DUCTING ,, REQUIREMENTS Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. ,, Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation. Lint accumulation should be cleaned regularly. ,, If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.
If the newdryer is beinginstalledinto an existingexhaustsystem,you must makesure: The exhaust system meets all local, state, and national codes. That a flexible plastic duct is not used. To Inspect and clean all lint buildup from inside the existing duct. The duct is not kinked or crushed. The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
With optional pedestal Required Dimensions base or stacking kit for installation With Pedestal (Model No.: WE302*' "< 57.8in. (146.7cm)to clearopen door _© 42.6in. (108.3cm) ........ _ ......... 53.7in. (136.5cm 32 in. (81.3cm) I_-- 5 in. (12.7cm) _ 30 in. (76.2cm) ---_1 N- 5in. 3 in. (12.7cm) 48in.2* (310cm2) 3 in, Closetor Door Required Dimensions _ for Installation (7.6cm) 1 in. -'_1 _ (2.5era) With Stacking 32.5in. J-_l (82.6cm) J_- 7.5in.** (19era) Kit (Model No.
EXHAUSTING The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amount of lint and moisture from being blown into the room. In the United States: All dryers must be exhausted to the outside. The required exhaust duct is 4 inches (10.2 cm) in diameter.
GAS REQUIREMENTS Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSVZ223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.
ELECTRICAL REQUIREM ENTS The wiring diagram is located on the plate below the control panel or frame back. Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer - if it doesn't fit the outlet, have a proper outlet installed by a qualified electrician.
ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. EXTENSION CORD. Gas models- DO NOT USE AN U,S, and Canada A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models - U,S, only Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service.
INSTALLATION For proper installation, - GENERAL we recommend PROCEDURE that you hire a qualified installer. Read these instructions completely before you begin the installation. To install the dryer, follow these steps: 1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer sideby-side so you have easy access to both appliances. To move the dryer easily, lay two of the carton cushion-tops on the floor.
Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below. 7. Three Wire system instructions: 6. A. B. O. External ground connector Neutral grounding wire (green/yellow) Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. 3_,,(1.9 cm) UL-listed strain relief 1o Loosen or remove the center terminal block screw. E 2.
U.S. MODELS: Z_ Risk Of Electric Shock WARNING All U.S.models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block. Remove the terminal block cover plate.
CONNECTING THE INLET HOSE M ETHOD1 The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. If space permits, attach the brass female end of the "Y" connector to the cold water faucet. 2. Turn the cold water faucet off. 3. Attach the straight end of long hose to "Y' connector. 4. Using pliers, tighten the coupling with an additional two-thirds turn. Do not overtighten, as it may damage the coupling. ,_L l 5.
DRYER EXHAUST TIPS Z_ Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 1. Make sure your dryer is installed properly so it exhausts air easily. 2. Use 4" diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually.
DOOR REVERSAL If you want to reverse the direction of the door, it is recommended calling a qualified service technician. 1, Unplug the power cord. 2, Remove the one screw from the COVER HANDLE. 3, Remove the 7 screws (MS, M4 2type) from the BRACKET DOOR. 4, Remove DOOR from BRACKET DOOR. 5, Remove the RINE-E and PIN from the BRACKET DOOR. PIN .... _'oi_ 6, Remove the BRACKET DOOR from the HINGE. J/ 7.
10. Remove the the 9 screws. (L12 lea, L14 5 ea, L18 2 ea). 11. Remove the COVER HANDLE and LEVER DOOR. L12 L14 j i i!!!!!!!i HANDLE COVER ':::'_,,,_t_ !iiiiiiiiiiiiiiiii:iiii_:ii!_ u8 :i"_i'_ _ ,/ DOOR LEVER 12. Remove the the 1 screw(L14). 13. Rotate the HOLDER GLASS (BIG ROUNDED STEEL) 180 °. 14. Assemble the the 1 screw (L14). 15. Assemble the COVER HANDLE and LEVER DOOR on the HOLDER GLASS. 16.Assemble the 9 screws. (L12 lea, L14 5 ea, L18 2 ea).
I _ J I z_To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY ....... INSTRUCTIONS before operating this appliance. OVERVIEW OF THE CONTROL PANEL Manua HEAVY DUTY BEDDING "_ NORMAL F ......................................................................................... PRESS woo DELICATES ACTIVE [] _!_' • i TOWELS //_ QUICK DRY TIME DRY /_i _ ., X_ \7, Very Dry High 60mlr_ More Dry Medium 5gram Med 40rain Normal Less Damp __
WOOL - For machine washable and tumble dryable wool only. DEMCATES - The DELICATES cycle is designed to dry heat-sensitive items at a low drying temperature. ACTIVE WEAR - The ACTIVE WEAR cycle is for exercise wear and outdoor wear such as sports jerseys, training pants, water-repellent jackets and other performance clothing. Thick fabrics like a zipper or velcro closure of a jacket, or training socks may not be completely dried. TOWELS - To dry bath towels and similar items.
I na n tnAct one, t _ J I Anti Static - To reduce statics by clothing friction and spray steam at the later period of drying cycle. It is only available with: NORMAL, HEAVY DUTY, PERM PRESS, DELICATES (Dry level of every cycle exceeds Normal) and TIME DRY cycle. Rack Dry - Rack Dry is available in the TIME DRY cycle. Temperature will be set to Extra Low only. (Refer to the "Rack Dry" section on page 25.
RACK DRY Using the drying rack 1. The drying rack is installed in the drum at in default state. 2. When using this dryer for the first time, remove the drying rack from the drum. Pull upwards vertically and take the drying rack out of the drum. Remove the package and keep it properly stored. 3. When you need to use drying rack, refer to the following steps for installation. Installing the drying rack 1. Open the dryer door. 2.
MY CYCLE Allows you to activate your custom dry (Cycle, Dry Level, Temp) with one button convenience. Press the My Cycle button to load and use the saved My Cycle options. The "My Cycle" light will indicate activation. Also, the chosen course and option lights will flicker. You can set options as follows in the My Cycle mode. 1. Press the Power button. 2. Select cycle using the Cycle Selector. 3. After cycle selection, set each option (Dry Level, Temp, Time) 4.
Child Lock Details - You can turn Child Lock on while your dryer is running. - Once you turn Child Lock on, no button, except for the power button, will respond until you turn off the Child Lock function. The Child Lock indicator will be lit. - If you have not turned off Child Lock, and then turned the dryer off and on, the Child Lock function will still be on. To turn off Child Lock, follow the instructions above.
I _ J I CLEAN THE LINT FILTER • After or before each load. To shorten drying time. To operate more energy efficiently. not operate your dryer without the lint filter in place. _Do Frame Front J_ Filter _OOF LOAD THE DRYER PROPERLY Place only one washload in your dryer at a time. In mixed loads, heavy and lightweight fabrics will dry differently. This may result in lightweight fabrics being dry while heavy fabrics remain damp at the end of a drying cycle.
0 The "Vent Sensor _ lamp is turned off. The "Vent Sensor _" lamp illuminates. 2 The "Vent Sensor _" lamp blinks. " The ductwork is free from blockages. When a part of the duct or the lint filter is blocked by lint or a foreign object. When the resistance is high because the duct is too long or bent. When the duct is blocked by lint or a foreign object. When the resistance is very high because the duct is too long or bent excessively.
CONTROL PANEL Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel. The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your dryer and wipe up any spills or overspray immediately. TUMBLER Remove any stains from the tumbler caused by crayon, ink, fabric dye (from new items such as towels or jeans) and so on with an all-purpose cleaner.
Special laundry tips Please follow the care label or manufacturer's instructions for drying special items. If care label instructions are not available, use the following information a guide, Bedspreads & Comforters as Follow the care label instructions or dry using the Bedding cycle. Make sure the item is thoroughly dry before using or storing. May require repositioning to ensure even drying. Blankets Use the Normal cycle and dry only one blanket at a time for best tumbling action.
CHECK THESE POINTS IF YOUR DRYER... Doesn't Doesn't run. heat. Doesn't d ry, ,, Make sure the door is latched shut. ,, • • Be sure the power cord is plugged into a live electrical outlet. Check your home's circuit breakers or fuses. Press the Start/Pause button again if the door is opened during the cycle. • Check your home's circuit breakers or fuses. • • • Select a heat setting other than Air Fluff. On a gas dryer, check that the gas supply is on. Clean the lint filter and exhaust duct.
Shuts off before load is dry The dryer load is too small. Add more items or a few towels and restart the cycle. The dryer load is too large. Remove some items and restart the dryer. Lint on clothes Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.
appendx FABRIC CARE CHART The following symbols provide garment care directions. The Clothing care labels include symbols for washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to mpeimize garment life and reduce laundering problems.
PROTECTING THE ENVIRONMENT This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. DECLARATION OF CONFORMITY This appliance complies with UL2158. SPECIFICATIONS Product 42.6" Product 44.6" 30" (762) B. Width Install E.
CYCLE CHART DV56 H9100E(G)* (o ' factory setting, Cycl_ Sensor ' selectable) !_ii_i!_i _i_i_!2!_i!_!i!i!iiii!_i_i_i_ ¸i_¸i_ ¸i_ ¸i_¸i_ ¸i_ ¸i_ ¸i_¸i_ ¸i_ ¸_i_i_i_i_ii_iii!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_ ¸_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_i!_i_!_i!_i!_ _ii!ii!i_!iiiii! EGO NORMAL Cottons, Work clothes, Linen Normal Dry (Adjustable) NORMAL Cottons, Work clothes, Linen, Mixed Loads Normal Dry (Adjustable) HEAVY DUTY Heavy Fabncs such as jean, corduroys, heavy wo
SAMSUNG DRYER LiMiTED WARRANTY TO ORiGiNAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
SAMSUNG DRYER LiMiTED WARRANTY TO ORiGiNAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of: One (1) year part and labor This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the Canada.
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
Scan the QR code* or visit www.samsung.com/spsn to view our heLpfuL How-to Videos and Live Shows *Requires Scan this with QUESTIONS your reader to be knstalled on your smartphone smartphone OR COMMENTS? U.S.A 1-800-SAMSUNG (726-7864) CANADA 1-800-SAMSUNG (726-7864) MEXICO 01-800-SAMSUNG (726-7864) www.samsung.com/us/support www.samsung.com/ca/support www.samsung.com/ca_fr/support (English) (French) www.samsung.com/mx/support Code No.
