Instruction Manual DVD-HR710 DVD-HR721 www.samsung.com English Downloaded From DvDPlayer-Manual.
IMPORTANT NOTE Getting Started Warning TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover omitted if the cover is detachable.
Precaution Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) 2) 3) 4) 5) 6) 7) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
Getting Started • Do not place the HDD & DVD RECORDER on top of a heat source. • Do not disconnect the AC power cord while the power is on. • Do not attempt to change the hard disk. This may result in a malfunction. use discs fixed with exposed tape adhesive or leftover peeled-off stickers.) • Do not use scratch-proof protectors or covers. • Do not use discs printed with label printers available on the market. • Do not load warped or cracked discs.
Audio CD • Recording and playback can be performed on DVDRW discs in both the Video and VR Modes. • Once a DVD-RW recorded in both the Video and VR Modes is finalised, you cannot perform addtional recording. • Once a DVD-RW recorded in Video Mode is finalised, it becomes DVD-Video. CD-RW/-R • Use a 700MB(80 minutes) CD-R/RW disc. If possible, do not use a 800MB(90 minutes) or above disc, as the disc may not play back.
Getting Started COPY PROTECTION • Many DVD discs are encoded with copy protection. Because of this, you should only connect your HDD & DVD RECORDER directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs. • This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Do not use the following discs! Getting Started • LD, CD-G, CD-I, CD-ROM, DVD-ROM, DVD+R and DVD+RW discs should not be used in this product. [Note] Disc types that can be played : CD/CD-R/-RW/ MP3/JPEG/DVD-Video/DVD-RAM/-RW/-R. For a DVD-RW/-R disc, which has been recorded in Video Mode on another component, it can play only when finalised. • Some commercial discs and DVD discs purchased outside your region may not be playable with this product. When these discs are played, either “No disc.
Getting Started Contents Case 3: Connecting to an AV amplifier with a digital output jack .................................................23 Connecting to AV 3 IN, DV input jack...................24 Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV3 IN jacks ........24 Case 2 : Connecting a Camcorder to the DV IN jack ..............................................................24 Getting Started Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copying from HDD to DVD..................................109 About the Copy Screen ................................................109 Changing the Record Mode .........................................112 Copying Multiple Titles at One Time..................112 Deleting an Undesired Title from the Copy List...........114 Previewing a Selected Title from the Copy List...........114 Selecting Record Mode of Each Title from the Copy List. ........................................................
Getting Started General Features recording time, LP & SP modes provide less recording time with higher quality recording, XP mode gives you the highest quality recording. Automated Quality Adjustment for Timer Recording The HDD(Hard Disk Drive) & DVD RECORDER allows you to record and play high quality digital video on DVDRAM/-RW/-R discs or on the HDD. You can also edit digital images on DVD-RAM/-RW/-R discs or HDD.
©2005 Samsung Electronics Co. All rights reserved; No part or whole of this user’s manual may be reproduced or copied without the prior written permission of Samsung Electronics Co. Make sure to check the following terms before reading the user manual. Icons that will be used in manual Icon How to use the HDD & DVD RECORDER Term Definition HDD This involves a function available on the HDD.
■ NOTE Getting Started ■ You can only use either the VR or Video mode on a DVD-RW, but not both at the same time. You can change the DVD-RW to format to another format by reinitializing. It should be noted that the disc's data will be lost when changing formats. Step 5 Editing a recorded disc Editing on discs is easier than conventional video tapes. The HDD & DVD RECORDER supports many different edit functions, possible only with DVDs and HDD.
Unpacking Setting the Remote Control Check for the supplied accessories below. You can control certain functions of another manufacturer’s TV with this remote control. Control function buttons involve: TV STANDBY/ON, PROG , TV VOL + -, Number buttons, TV MUTE, INPUT button.
Getting Started To determine whether your television is compatible, follow the instructions below. 1. Switch your television on. 2. Point the remote control towards the television. 3. Press and hold the TV STANDBY/ON button and enter the two-figure code corresponding to the brand of your television, by pressing the appropriate number buttons.
Description Getting Started Front Panel 1 2 9 3 10 1. STANDBY/ON BUTTON Turns the HDD & DVD RECORDER on and off. 2. DVD BUTTON Select DVD mode. 3. HDD BUTTON Select HDD mode. 4. DISC TRAY Opens to accept a disc. 5. DISPLAY Displays the playing status, time, etc. 6. STOP BUTTON Stops disc playback. 7. SEARCH/SKIP BUTTONS Goes to the next title/chapter/track or goes back to the previous title/chapter/track. 4 5 11 6 7 12 8 13 14 8. PROG BUTTONS Select TV preset Channels.
Getting Started Rear Panel Fan The fan always revolves when the power is on. Ensure a minimum of 10cm clear space on all sides of the fan when installing the product. 1. DIGITAL AUDIO OUT(OPTICAL) 5. S-VIDEO OUT Connects to an amplifier having a digital optical audio input jack. 2. DIGITAL AUDIO OUT(COAXIAL) Connects to an amplifier having a digital coaxial audio input jack. 3. AUDIO OUT Connects to the audio input of external equipment using audio cables. 4.
Tour of the Remote Control 13. OK/DIRECTION Buttons (…†œ √ Buttons) 14. RETURN Button 1 20 3 21 4 5 22 7 8 9 10 11 23 24 25 26 7 9 27 28 17. COPY Button Press this when you copy DVD to HDD or HDD or viceversa. To start copying, press the COPY button on the title list screen or press the COPY button during the playback. 18. REPEAT Button Allows you to repeat a title, chapter, track or disc. 19. REC PAUSE Button Use this to pause during recording. 20. TV STANDBY/ON Button 29 21.
Connecting & Setting Up Connecting & Setting Up This section involves various methods of connecting the HDD & DVD RECORDER to other external components and required initial setting modes. Quick Overview A Quick Overview presented in this guide will give you enough information to start using the HDD & DVD RECORDER.
Additional connections You can connect your HDD & DVD RECORDER to the television using the SCART cable if the appropriate input is available on the television. 1. Connect the RF cable as shown. 2. Connect one end of the SCART cable to the AV1 socket on the rear of the HDD & DVD RECORDER. 3. Plug the other end into the appropriate connector on the television. 4. Plug in the HDD & DVD RECORDER and TV 5. Turn on the HDD & DVD RECORDER and TV. 6.
Connecting & Setting Up Antenna + HDD & DVD RECORDER + External decoder box + TV If you connect external decoder box to HDD & DVD RECORDER, you can record scrambled channels (CANAL+or Premiere broadcasts) received through the built-in TV tuner in HDD & DVD RECORDER. Other type of connecting the Video output cable There are several ways to output video signal not using scart cables. Select one of the following video connecting that best suits you below.
Case 1 : Connecting to a Video (Composite) output jack Case 2 : Connecting to an S-Video output jack 1. Connect an S-Video cable (not included) between the S-VIDEO OUT jack on HDD & DVD RECORDER and S-VIDEO INPUT jack on your TV (or AV amplifier). • You will enjoy high quality images. 2. Connect audio cables (white and red) between the AUDIO OUT jacks on the HDD & DVD RECORDER and AUDIO IN jacks on TV (or AV amplifier). (See pages 22~23) 2.
Case 3 : Component Video output jacks 1. Connect Component video cables(not supplied) between the COMPONENT OUT(Y,PB,PR) jacks on HDD & DVD RECORDER and COMPONENT IN(Y,PB,PR) jacks on your TV. Connecting & Setting Up • You will enjoy high quality and accurate colour reproduction images. 2. Connect audio cables (white and red) between the AUDIO OUT jacks on the HDD & DVD RECORDER and AUDIO IN jacks on TV (or AV amplifier). (See pages 22~23).
Case 2 : Connecting to a stereo amplifier with AV output jacks Case 3: Connecting to an AV amplifier with a digital output jack If your stereo amplifier only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks. If your AV amplifier has a Dolby Digital, MPEG2 or DTS decoder and a digital input jack, use this connection. To enjoy Dolby Digital, MPEG2 or DTS sound, you will need to set up the audio settings.
Connecting & Setting Up Connecting to AV 3 IN, DV input jack Case 2 : Connecting a Camcorder to the DV IN jack If your digital camcorder has a DV output jack, connect it to the DV input jack of your HDD & DVD RECORDER. This allows you to connect your HDD & DVD RECORDER to other external devices and view or record their outputs.
System Setup On-Screen Menu Navigation The on-screen menus allow you to enable or disable various functions on your HDD & DVD RECORDER. Use the following buttons to open and navigate through the on-screen menus. Setup HDD Title Music Photo Programme System √ Clock Set √ Language √ Audio √ Video √ Parental Control √ Install √ MOVE On-Screen Menu Navigation . . . . . . . . . . . . . . . . .25 SELECT 1 MENU Button 2 …†, œ √ Buttons 3 OK Button 4 RETURN Button Plug & Auto Setup . . .
Plug & Auto Setup 5 Select “Country” using the …† œ √ buttons to select your country. Country Selection Your HDD & DVD RECORDER will automatically set itself up when it is plugged in for the first time. TV stations and clock will be stored in memory. The process takes a few minutes. Your HDD & DVD RECORDER will then be ready for use. A NL S PL B I CH CZ Others DK N TR FIN P GR D E HU • Refer to following abbreviation table when selecting “Country”.
8 Wait until current date and time are displayed automatically. If you want to exit auto clock setting, press MENU button. Please wait. Now setting the clock. Setting the Clock This menu is used to set the current time. You need to set the time to use timer recording. If you want to exit clock setting, press the [MENU] button. 1 9 With the unit in Stop mode, press the MENU button. Title Check the date and time.
4 Press the …† buttons to select On for the Auto Clock. Presetting Channels with the Auto Setup function Clock Set HDD Title Music Time Date 12 : 00 Auto Clock 01 / JAN SAT 2005 On Photo Programme This feature allows you to manually set the HDD & DVD RECORDER tuner band to Antenna or Cable, whichever you connected to the Antenna In jack during initial setup. Setup 0~9 NUMBER System Setup 5 SELECT RETURN EXIT Press the OK button, then the date and time will be saved.
4 • The first frequency band is scanned and the first station found is displayed and stored. And the HDD & DVD RECORDER searches for the second station and so on. • When the automatic scanning procedure has finished, the HDD & DVD RECORDER switches automatically to programme 1. • The number of stations automatically stored by the HDD & DVD RECORDER depends on the number of stations that it has found. Press the …† buttons to select Auto Setup, then press the OK or √ button.
Presetting Channels with the Manual Setup function You can add preset channel that Auto Channel Search missed. And you can delete a channel you wish to remove. You can programme the order of channels. With the unit in Stop mode, press the MENU button. 2 Press the …† buttons to select Setup, then press the OK or √ button. System Setup 1 Setup 5 Press the …† buttons to select a PR(programme) you wish to edit, delete, or swap, then press the ANYKEY button. Select Edit, Delete or Swap.
Setting up the Language Options 4 Press the …† buttons to select the desired language option, press the OK or √ button. Language HDD Audio Title Subtitle If you set the audio, subtitle, disc menu and on-screen menu, in advance, they will come up automatically every time you watch a movie. If the selected language is not recorded on the disc, the original pre-recorded language is selected.
Auto Power Off Setting 5 Press the …† buttons to select the desired item, then press the OK or √ button. • Off : Auto power off is disabled. This feature automatically turns off your HDD & DVD RECORDER, if you do not press any button for the selected time. With the unit in Stop mode, press the MENU button. 2 Press the …† buttons to select Setup, then press the OK or √ button.
CM Skip Time Setting 4 Press the …† buttons to select CM Skip Time, then press the OK or √ button. System HDD Title Music When a programme recorded on a HDD, a DVD-RAM, a DVD-RW, or a DVD-R is played, the unit can be set to automatically skip a portion of the programme corresponding to a CM(commercial) skip time set by the user.
EP Mode Time Setting 4 Press the …† buttons to select EP Mode Time, then press the OK or √ button. System HDD Title You can select one of four recording modes by pressing the REC MODE button repeatedly. EP mode is one of four REC Mode (XP, SP, LP, EP). In EP(Extended Play) mode, you can set recording time to 6 or 8 hours with this setting. Music System Setup 1 2 Press the …† buttons to select Setup, then press the OK or √ button.
Setting up the Front Display Options 4 Press the …† buttons to select Front Display, then press the OK or √ button. System HDD Title Music Adjust the brightness of the unit’s front panel display. Photo Programme Auto Power Off : Off √ CM Skip Time : 15 Sec √ EP Mode Time : 6 Hour √ Front Display : Auto Dim Bright √ Chapter Creator : Off Dim √ NICAM √ : On Auto Dim DivX(R) Registration √ Setup MOVE 1 With the unit in Stop mode, press the MENU button.
Automatic Chapter Creator 4 Press the …† buttons to select Chapter Creator, then press the OK or √ button. System DVD-RW(V) Title A DVD-Video consists of ‘Titles’ and ‘Chapters’. When you record one programme, it makes one Title. If you use this function, the Title will be divided into Chapters.
8 Press the STOP button to stop recording. 9 To display the created titles, finalise the disc (See page 124) and then press the TITLE MENU button. The title menu will be displayed. Previous NICAM programmes are divided into 3 types. NICAM Stereo, NICAM Mono and Bilingual (transmission in another language). NICAM programmes are always accompanied by a standard mono sound broadcast and you can select the desired sound by setting NICAM on or off.
4 Press the …† buttons to select NICAM, then press the OK or √ button. Setting up the Audio Options System HDD Title Music Auto Power Off : Off √ CM Skip Time : 15 Sec √ EP Mode Time : 6 Hour √ : Auto Dim √ Front Display Photo Chapter Creator : Off Programme √ Off : On √ DivX(R) RegistrationOn √ NICAM You can connect the HDD & DVD RECORDER to an external amp or Home theatre. Allows you to setup the Audio device and sound status depending on the audio system in use.
Digital Output V-Mode Compatibility 1. PCM : Select this when your equipment is not decode Dolby Digital compatible. This feature is about the setup for selecting audios when recording the NICAM STEREO (Multi-audio) broadcasting on HDD. It does not affect to the direct DVD recording of a programme. 2. Bitstream : Outputs Dolby Digital (or MPEG-2) audio as bitstream. Select this when your AV receiver or AV amplifier has a Dolby Digital (or MPEG-2) Decoder.
Setting up the Video display Options Press the …† buttons to select the desired video option, then press the OK or √ button. 4 Video HDD This function allows you to setup the TV screen settings. This function depends on disc type. It may not work for some disc types. √ : 16:9 Wide Box 4:3 Letter 3D Noise Reduction : Off 4:3 Pan/Scan√ Title TV Aspect Music Video Output : Component 16:9 Wide √ Photo Programme Setup System Setup MOVE 1 With the unit in Stop mode, press the MENU button.
3D Noise Reduction (motion adaptive noise reduction) 3 Press the …† buttons to select Video, then press the OK or √ button. Video setup menu will be displayed. Video HDD TV Aspect Title : 4:3 Letter Box √ Video Output Video √ 3D Noise Reduction :Off Off Music HDD :On Component √ TV Aspect Title Photo : 4:3 Letter Box √ √ 3D Noise Reduction : Off Music Programme Video Output √ : Component√ Photo Setup MOVE SELECT RETURN Programme EXIT Setup MOVE SELECT RETURN EXIT 1.
Setting up the Progressive scan 3 The message “Video Output Mode Progressive Scan” will appear. The video will now be Progressive Scan. If your TV supports Progressive Scan, press the P.SCAN button on the front of the HDD & DVD RECORDER. To view ‘Progressive scan mode’, first connect the component cable.(See page 22) Video Output Mode Progressive Scan Be sure the Component cables are connected properly. System Setup 1 With the unit in Stop mode, press the P.
Canceling the Progressive scan 1 With the unit in Stop mode, press the P.SCAN button on the front of the HDD & DVD RECORDER. The message “Press [Yes] to confirm Interlace scan mode. Otherwise, press [No]” will appear. Press the œ √ buttons to select Yes, and then press the OK button. ■ NOTE ■ Do not press the P.SCAN button if you are using a TV that does not support Progressive mode as nothing will be displayed on the screen. If you press the P.
Setting up the Parental Control Enter the 4-digit password using the number buttons on the remote control. The “Confirm the password” message will be displayed. Enter your password again. 4 Parental Control The Parental Control function works in conjunction with DVDs that have been assigned a rating which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc. HDD Title Confirm the password.
Setting the Rating Level 1 Changing the Password Press the …† buttons to select Rating Level, then press the OK or √ button. 1 Press the …† buttons to select Change Password, then press the OK or √ button.
Before Playing Playback Read the following information before playing a disc. This section introduces basic functions of playback and playback by disc type. Dolby Digital DTS Region code (DVD-Video only) Both the HDD & DVD RECORDER and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play. The Region Number for this HDD & DVD RECORDER is described on the rear panel of the HDD & DVD RECORDER.
Discs that cannot be played • • • • DVD-Video with a region number other than “2” or “ALL” 12cm 2.6 GB and 5.2 GB DVD-RAM 3.9 GB DVD-R Disc for Authoring. DVD-RAM/-RW(VR mode) not recorded following the Video Recording Standard • Unfinalised DVD-R,unfinalised DVD-RW(V mode) recorded on other equipment. • DVD-ROM/DVD+RW/PD/MV-Disc, etc • CVD/CD-ROM/CDV/CD-G/CD-I ■ NOTE ■ ■ ■ ■ 1 Press the OPEN/CLOSE button. 2 Place a disc gently into the tray with the disc’s label facing up.
Using the Disc Menu & Title Menu Using the Search & Skip Functions Searching through a Chapter or Track Some type of discs contain a dedicated menu system that allows you to select special functions for title, chapter, audio track, subtitle, film preview, information on characters, etc. For DVD-VIDEO Disc Press the DISC MENU button to enter the disc menu of the disc. 1 • Move to the setup menu related to playback operation. • You can select audio language and subtitle etc. provided by the disc.
Skipping Chapters, Tracks or Markers During play, you can search quickly through a chapter or track. Slow Motion Play/ Step Motion Play Slow Motion Play 1 During play, press the SKIP ( remote control. ) buttons on the • If you press the SKIP ( ) button, it moves to the beginning of the chapter or track or marker(HDD/DVD-RAM/-RW(VR mode)). Pressing the button once again within 3 seconds returns to the beginning of the previous chapter or track or marker(HDD/DVD-RAM/-RW(VR mode)).
Step Motion Play Press the STEP( in the pause mode. ) buttons on the remote control • Each time the button is pressed, a new frame will appear. When the STEP( About ANYKEY ) button is pressed, the previous The ANYKEY function allows you to easily search for a desired scene by accessing title, chapter, time. You can also change the subtitle and audio settings and set some features including Marker, Angle, Zoom, Repeat, Select Media, Disc Manager. frame will be activated.
■ 3 Press the …† buttons to select Title or Chapter. 4 Press the œ √ buttons or number buttons to select the desired scene, then press the OK button. NOTE ■ ■ This may not work for some discs. When an audio CD(CD-DA) or an MP3 disc is inserted, depending on the disc type, the information display may not appear. The Time Search function does not operate in some discs.
Playing the Title List 2 Press the …† buttons to select an entry you want to play from Title List, then press the OK or PLAY ( ) button. The selected entry (title) will be played back. - About INFO button If you press the INFO button once during a playback, the system information screen appears.: Displays Active Status, Background Status, and Main Screen information. Follow these instructions to play back a scene from the Title List.
Navigation Menu 2 Press the …† buttons to select an entry you want to play from Title List, then press the ANYKEY button. Title List Scene Navigation HDD Rename No. Protection 001 002 003 004 Copy Delete If there is a title composed of markers (See page 56), you can search the desired scene using the Scene Navigation.
Time Navigation Using the ANYKEY button (VR mode) 1 Press the ANYKEY button during playback. Using this function, you can search scene minute-byminute from the recorded title list. Search Using the TITLE LIST button √ Navigation Marker Subtitle √ Audio √ Repeat √ Zoom Select Media 1 √ Disc Manager With the unit in Stop mode/Playback mode, press the TITLE LIST button. The Title List screen is displayed. Title List 2 Press the …† buttons to select Navigation, then press the OK or √ button.
2 Press the …† buttons to select an entry you want to play from Title List, then press the ANYKEY button. Title List HDD Rename No. Protection 001 002 003 004 Copy Delete Edit √ Playlist √ 19/JAN/2005 12:15AV3 Title MOVE 3 1 Press the ANYKEY button during playback.
Using Markers 2 Press the OK button when the desired scene appears. • The number 01 is displayed and the scene is memorized. Marker 01 -- -- -- -- -- -- -- -- -- N:1 (VR mode) MOVE √ PLAY CANCEL RETURN Using the MARKER button 1 Press the MARKER button during playback. Marker -- -- -- -- -- -- -- -- -- -- SELECT N:0 3 Press the œ √ buttons to move to the next position. 4 Press the OK button again when the desired scene appears. • The number 02 is displayed and the scene is memorized.
Playing back a marker Clearing a marker Using the MARKER button 1 Press the MARKER button during playback. Marker MOVE 01 02 -- -- -- -- -- -- -- -- √ PLAY CANCEL Using the MARKER button 1 N:2 Marker RETURN MOVE √ PLAY CANCEL RETURN Using the ANYKEY button. • Press the ANYKEY button during playback. • Press the ANYKEY button during playback.
■ When a marker is cleared while HDD/DVDRAM/-RW (VR mode) is playing, marker numbers will change. For example, if the 7th marker is cleared after ten markers are registered, the marker numbers after the eighth will automatically move ahead by one and the 8th marker becomes the 7th. 2 Press the OK button when the desired scene appears. • The number 1 is displayed and the scene is memorized.
Playing back a bookmark Clearing a bookmark Using the MARKER button 1 Press the MARKER button during playback. Using the MARKER button 1 Bookmark 1 2 - - - - - - - -- MOVE √ PLAY CANCEL Press the MARKER button during playback. Bookmark 1 2 - - - - - - - -- RETURN MOVE √ PLAY CANCEL RETURN Using the ANYKEY button. Using the ANYKEY button. • Press the ANYKEY button during playback. • Press the ANYKEY button during playback.
Selecting the Subtitle Language Using the ANYKEY button 1 Press the ANYKEY button during playback. Selects one of the subtitle language recorded on the disc. Search Navigation √ Marker Subtitle √ Audio √ Repeat √ Zoom Select Media √ Disc Manager (VR mode) Using the SUBTITLE button 1 Press the SUBTITLE button during playback. Subtitle 2 Press the …† buttons to select Subtitle, then press the OK or √ button.
Selecting the Soundtracks & Audio Channels Using the ANYKEY button 1 Press the ANYKEY button during playback. Selecting the Audio Search Navigation Selects one of the soundtracks recorded on the disc. Also selects the audio channels from recorded TV programmes. √ Marker Subtitle √ Audio √ Repeat √ Zoom Select Media √ Disc Manager (VR mode) Using the AUDIO button 1 Press the AUDIO button during playback. 2 Press the …† buttons to select Audio, then press the OK or √ button.
Changing the Camera Angle Repeat Play When a DVD VIDEO contains multiple angles of a particular scene, you can select the Angle function. Playing Repeatedly(Repeat Playback) Using the ANYKEY button 1 Press the ANYKEY button during playback. Using the REPEAT button 1 Press the REPEAT button during playback. Repeat Search Off Bookmark Audio √ Subtitle √ Angle √ Repeat √ Zoom Playback Select Media 2 √ Press the …† buttons to select Angle, then press the OK or √ button.
Repeat A-B Using the ANYKEY button 1 Press the ANYKEY button during playback. Using the REPEAT A-B button Search Navigation √ 1 Marker Subtitle √ Audio √ Repeat √ Zoom Select Media Press the REPEAT A-B button during playback. Repeat A-B Off √ Disc Manager 2 Press the …† buttons to select the Repeat, then press the OK or √ button.
Using the ANYKEY button 1 Zooming-In Press the ANYKEY button during playback. Search Navigation √ Marker Subtitle √ Audio √ Repeat √ 1 Zoom Select Media √ Press the ANYKEY button during playback. Disc Manager Search Navigation √ Marker 2 Press the …† buttons to select Repeat, then press the OK or √ button.
Select Media Playing an Audio CD/MP3 Playing an Audio CD(CD-DA) 1 Press the ANYKEY button during playback. 1 Insert an audio CD (CD-DA) into the disc tray. • The audio CD menu appears and the tracks (songs) are played automatically.
Buttons on the Remote Control used for Audio CD(CD-DA) playback DVD TV Playing an MP3 Disc Insert an MP3 disc into the disc tray. • The MP3 menu is displayed and the tracks (songs) are played automatically. 1 Music List CD √ 02 : 10 Flower.mp3 .. Flower.mp3 MP3 01/15 4.0 MB MP3 Love.mp3 MP3 Straight from the heart.mp3 MP3 Run to you.mp3 MP3 Heaven.mp3 MP3 This Love.
Buttons on the Remote Control used for MP3 playback DVD Repeat CD (CD-DA) & MP3 Using the REPEAT button. TV 1 Press the REPEAT button during playback. Music List CD √ 02 : 10 TRACK 1 TRACK 1 CD-DA 01/15 04:57 CDDA TRACK 2 CDDA TRACK 3 CDDA TRACK 4 CDDA TRACK 5 CDDA TRACK 6 CDDA TRACK 7 1/3 Page MOVE 2 SELECT RETURN EXIT Press the REPEAT button repeatedly to select the repeat mode you want.
New Playlist Using the ANYKEY button 1 Press the ANYKEY button during the Music List playback. You can register a maximum 28 tracks in the playlist. 1 Press the ANYKEY button during the Music List playback.
Go To Playlist 4 If you playlisted a wrong track, press the √…† buttons to select the wrong track, then press the OK or CANCEL button. The wrong track will be removed. 1 Press the ANYKEY button during the Music List playback. Make Playlist CD Music List 01. TRACK 1 TRACK 2 02. TRACK 3 CDDA TRACK 3 03.
Delete the Playlist 1 Go To Edit Playlist Press the ANYKEY button during the Music List playback. 1 Press the ANYKEY button during the Music List playback.
Go To Music List 5 Press the …† buttons to select the Go To Edit Playlist, then press the OK or √ button. 1 Edit Playlist Press the ANYKEY button during the Playlist playback.
Select Media (MP3) 1 Viewing a Picture Press the ANYKEY button. Music List CD » 02 : 10 Flower.mp3 .. Flower.mp3 Copy Play Mode ROOT Go 01/15 To Playlist New 4.0Playlist MB Select Media √ MP3 Love.mp3 MP3 Straight from the heart.mp3 MP3 Run to you.mp3 MP3 Heaven.mp3 MP3 This Love.mp3 √ MOVE 1 Insert a JPEG disc or Mixed disc (JPEG + MP3 + DivX) into the disc tray.
Slide Show - To stop the Slide Show - 4 1 Press the ANYKEY button. Press the ANYKEY button. Photo List CD DSC01194.JPG .. DSC01189.JPG Index: 1/10 DSC01190.JPG DSC01191.JPG DSC01194.JPG DSC01199.JPG Copy Slideshow √ Slide Show DSC01192 DSC01193.JPG Select Media √ MOVE 5 1/2 Page SELECT √ Slideshow Off Go To Photo List RETURN EXIT Press the …† buttons to select Slide Show, then press the OK or √ button.
Rotate Zoom To setup, follow steps 1 to 3 in page 72. 4 Playback 5 6 Press the OK button to select the picture you want to see, then press the ANYKEY button. To setup, follow steps 1 to 3 in page 72. 4 Press the OK button to select the picture you want to see, then press the ANYKEY button. Slideshow √ Slideshow √ Rotate √ Rotate √ Zoom Zoom Go To Photo List Go To Photo List Press the …† buttons to select Rotate, then press the OK or √ button.
Go To Photo List Playing an MPEG4 To setup, follow steps 1 to 3 in page 72. 4 Press the OK button to select the picture you want to see, then press the ANYKEY button. Using the MENU button Slideshow √ Rotate √ 1 Insert a DivX disc or Mixed disc (JPEG + MP3 + DivX) into the disc tray. 2 Press the …† buttons to select Title, then press the OK or √ button. (In case of playing a DivX Disc, see number 4 on this page.
DivX Subtitle Encoding 5 When MPEG4 file is played, you can use following functions. Pressing the STOP ( ) button once during playback will display the file list, pressing the button again will exit the menu screen. 1 Press the ANYKEY button during playback. MPEG4 Function Description Function Search Description Audio √ Subtitle √ Repeat √ Subtitle Encoding √ Skip During play, press the SKIP ( ) buttons, it moves forward or backward 5 minutes.
Recording Before Recording This unit can record on various types of discs. Before recording, read the following instructions and select the disc type according to your preference. Recordable Discs This section shows various HDD & DVD Recording methods. This HDD & DVD RECORDER can record on the following discs. HDD DVD-RAM DVD-RW DVD-R •DVD-RWs and DVD-RAMs are rewritable.
Recording Formats When you insert an unused disc, the following message appears. Since available functions differ depending on the disc type, select a disc that best fits your preferences. DVD-RAM: Use after formatting the disc. Recording Mode Select one of four recording modes by pressing the REC MODE button repeatedly while the unit is in Stop mode for the desired recording time and picture quality. In general, picture quality improves as the recording time decreases.
Unrecordable pictures Video with copy protection cannot be recorded on this HDD & DVD RECORDER. When the HDD & DVD RECORDER receives a copyguard signal while recording, recording stops and the following message appears on the screen. Recording the current TV programme you are watching Check that the disc has enough available space for the recording. Adjust the recording mode. You cannot record copy protected movie.
3 Press the REC MODE button repeatedly, (or press the REC MODE button and then press the …† buttons) to select the recording speed(quality). ➞ SP ➞ LP ➞ EP ➞ XP ■ You can not change the recording mode and the PROG while recording. ■ Recording will stop automatically if there is no free space left for recording. ■ Up to 99 titles can be recorded onto a disc.(DVD-RAM/-RW/-R) ■ Up to 999 titles can be registered on the HDD.
Recording from external equipment you are watching 4 Press the REC button. Information concerning the external input mode is displayed on the screen, then recording begins. Icon( ) is displayed on the front panel. - To pause recording Before you start Check that the disc has enough available space for the recording. Adjust the recording mode. • Press the REC PAUSE button to pause a recording in progress. • Press the REC PAUSE button again during pause to resume recording.
Copying from a Camcorder 4 Press the INPUT button to select DV. If the input is set to DV, a playback/record menu that enables camcorder control appears on the top of the screen. DV The DV device is connected. You may control the Camcorder using the IEEE1394 (DV) interface. MOVE RETURN 1 Connect the DV output jack of your camcorder to the DV input jack on the front of your HDD & DVD RECORDER using a DV cable.
Making a One Touch Recording (OTR) ■ NOTE The timer counter decreases by the minute from 8:00 to 0:00, then the HDD & DVD RECORDER stops recording. - To stop recording You can set the HDD & DVD RECORDER to record in 30-minute increments up to 8 hours by pressing the REC button. Press the STOP ( ) button. The message “Do you want to stop recording?” is displayed. • Press the œ √ buttons to select Yes, then press the OK button. • Or press the STOP ( 1 Press the HDD or DVD button.
2 Chasing Play Press the OK or PLAY ( ) button. It plays back the title that you are currently recording from the beginning. √ Play You can play back from the beginning of the programme you are currently recording. While Recording 1 Press the PLAY ( ) button. It plays back the title that you are currently recording from the beginning. Playback is not available for 10 seconds from the start of recording. You can use the SKIP ( ) and other playback-related buttons to view the previous recorded list.
Simultaneous Recording and Playback 1 Press the STOP ( ) button. Playback screen disappears and the recording in progress screen appears. You can watching the previous title list while recording a programme. 2 Pressing the STOP ( stop the recording. - Stopping Playback / Recording - ■ ) button once more will No sound is heard during search mode. NOTE Using the TITLE LIST button 1 With the unit in recording mode, press the TITLE LIST button. The Title List screen is displayed.
Making a Timer Recording 3 Press the OK button to select Add a list. The Timer Record List screen is displayed. Timer Record List HDD No. To Current Time 12:00 Source Date Start End Mode VPS/PDC Add a list Title No. 01 To Source Date Start End HDD PR 02 01 JAN 12 : 00 14 : 00 Mode VPS/PDC SP Title 1. Check the antenna cable is connected. 2. Check the remaining time of the disc. 3. Check the date and time are correct.
• Start/End Time : Start and end time of the timer recording. • Mode (Recording Mode) : - FR (Flexible Recording) : Select when you want to set video quality automatically. In FR mode, the most suitable record mode is adjusted automatically, according to remaining time on the disc and length of the timer recording. This function is selected only one mode in XP, SP, LP and EP modes. 5 After selecting the set up value for each mode, press the OK button to select Save, and press the OK button again.
Flexible Recording (for Timer recording only) Editing the Timer Record List Follow these directions to edit the timer record list. In FR mode, the most suitable record mode is adjusted automatically, according to remaining time on the disc and length of the timer recording. This function is selected only one mode in XP, SP, LP and EP modes and you can use this mode for timer recording. The FR mode recording setup is the same as Timer Recording. When setting the mode in step 4, set the FR mode.
= 3 Press the …† buttons to select the number of the Timer Record List you want to edit, then press the ANYKEY button. • The Add, Edit, Delete and Go To History List items is displayed. Timer Record List HDD No. 01 02 03 To Current Time 12:00 Source HDD HDD HDD Add Date PR 02 PR 07 AV2 Start End 01 JAN 12 : 00 15 JAN 14 : 10 01 JAN 15 : 10 Add a list 14 : 00 14 : 30 15 : 30 Deleting a Timer Record List Follow these directions to delete an entry from the timer record list.
3 Press the …† buttons to select the number of the Timer Record List you want to delete, and then press the ANYKEY button. • The Add, Edit, Delete and Go To History List items are displayed. Timer Record List HDD No. 01 02 03 To Go To History List You can confirm the performance results of title lists that have passed the reserved recording time.
3 Information about History List Press the ANYKEY button. • The Add and Go To History List items is displayed. Informs whether the selected History List performed a Timer Recording successfully. Timer Record List HDD Current Time 12:00 No. To Source Date Start End 01 -- --- -- / -- --:-- --:-- Mode VPS/PDC -- -- -1 Press the …† buttons to select the number of the History List, then press the ANYKEY button. 5 History List HDD Add Go ToTime History List Available HDD MOVE 29:10 SP No.
Go To Timer Rec List Press the …† buttons to select Delete, then press the OK or √ button. 6 History List HDD No. Source 01 02 03 Date Start End Mode VPS/PDC To PR 02 01 JAN 12 : 00 14 : 00 SP On HDD PR 07 15 JAN 14 : 10 14 to : 30delete SP No.01? On HDD Do you want AV2 01 JAN 15 : 10 15 : 30 SP On HDD Yes Status Switches directly from the History List to the Timer Rec List. -1 Press the ANYKEY button. 5 OK OK OK History List HDD No No.
Editing This section introduces basic functions of editing and explains both edit functions for the recording on a disc and edit functions for the entire disc. • Title List Title List is a list of previously recorded programmes. If a title is deleted, that title cannot be played again. Basic Editing (Title List) . . . . . . . . . . . . . . . . . . . . .94 Advanced Editing (Playlist) . . . . . . . . . . . . . . . . . .101 Copying from HDD to DVD . . . . . . . . . . . . . . . . . .
Basic Editing (Title List) 3 Press the …† buttons to select Rename, then press the OK or √ button. The Rename screen is displayed. Rename HDD Renaming(Labeling) a Title 1 8 / JAN / 2005 12:15 AV3 Follow these instructions to rename a title list entry, i.e., to edit the title of a recorded programme. Back Space MOVE Using the TITLE LIST button 1 4 With the unit in Stop mode/Playback mode, press the TITLE LIST button. The Title List screen is displayed.
Locking (Protecting) a Title Follow these instructions to lock an entry to protect it from accidental deletion. 3 Press the …† buttons to select Protection, then press the OK or √ button. Title List HDD Title Protection: 18/JAN/2005 12:15 AV3 Using the TITLE LIST button V-Mode Compatibility MOVE With the unit in Stop mode/Playback mode, press the TITLE LIST button . The Title List screen is displayed. Title List HDD No.
3 Deleting a Title Press the …† buttons to select Delete, then press the OK or √ button. Follow these instructions to delete an entry from the Title List. Title List HDD Do you want to delete? (Related playlists may be deleted.) 18/JAN/2005 12:15 AV3 Using the TITLE LIST button SP With the unit in Stop mode/Playback mode, press the TITLE LIST button. The Title List screen is displayed. No.
■ NOTE You cannot delete a protected entry. If you want to delete a protected entry, select “Off” in the Title Protection menu. (See page 95) ■ When the Disc Protection has been set to Protected, you cannot delete titles. (See page 120) ■ Once an entry is deleted from the Title List it cannot be recovered. ■ Once DVD-RW/-R is finalised, it cannot be deleted. Splitting a Section of a Title (Split) Follow these instructions to split a section of a Title List entry into two titles.
3 Press the …† buttons to select Edit, then press the OK or √ button. The Edit menu is displayed. Split HDD 18/JAN/2005 12:15AV3 Title List No. 001 Split 1 Split 2 00:00:00 00:05:21 Title List HDD Rename No.
Deleting a Section of a Title (Partial Delete) 3 Follow these instructions to delete a section of a Title List entry. Press the …† buttons to select Edit, then press the OK or √ button. The Edit Title List screen is displayed. Title List HDD Rename No.
Edit Title List Screen Elements 7 Press the œ √ buttons to select Delete, then press the OK button. Partial Delete HDD 18/JAN/2005 12:15AV3 Partial Delete Title List No. 001 Start HDD End 18/JAN/2005 12:15AV3 Title List No.
3 Advanced Editing (Playlist) Press the …† buttons to select New Playlist, then press the OK or √ button. The Make Playlist screen is displayed. Make Playlist HDD New Playlist Scene No. 001 Creating a Playlist Follow these instructions to create a new playlist entry from a recorded title. Title List 1/4 Start End 00:00:00 00:00:00 00:00:10 Start End Make MOVE Return SELECT RETURN EXIT (VR mode) Using the TITLE LIST button 1 4 Press the OK button at the start point.
Playing Entries in the Playlist 6 Press the œ √ buttons to select Make, then press the OK button. • To make a scene for the playlist. A new Make scene screen is displayed. Repeat steps 4~6 to make a new scene for the playlist. A new scene will be added to the current playlist. You can check and see all the scenes on the Edit playlist screen. (See page 104) • To make a new playlist. Repeat steps 1~6 if you want to make a new playlist. 7 Follow these instructions to play the playlist entries.
Renaming a Playlist Entry Follow these instructions to rename a playlist entry, i.e. to edit the title of a playlist entry. 3 (VR mode) Press the …† buttons to select Rename, then press the OK or √ button. The Rename screen is displayed. Rename HDD 1 8 / JAN / 2005 12:15 AV3 Using the PLAY LIST button Back Space 1 With the unit in Stop mode/Playback mode, press the PLAY LIST button. The Edit Playlist screen is displayed. Playlist HDD No.
Editing a Scene for the Playlist Follow these instructions to edit scenes for a playlist. 3 Press the …† buttons to select Edit Playlist, then press the OK or √ button. The Edit Scene screen is displayed. (VR mode) Edit Playlist HDD Playlist No. 1 Using the PLAY LIST button 1 01 00:00:26 02 0:00:07 03 00:06:04 05 0:00:26 06 00:01:07 07 00:00:00 With the unit in Stop mode/Playback mode, press the PLAY LIST button. The Edit Playlist screen is displayed.
Modifying a Scene (Replacing a Scene) 7 Press the OK button at the end point of the scene. To setup, follow steps 1 to 3 in page 104. Modify Scene 4 HDD Press the …† œ √ buttons to select the scene you want to modify, then press the ANYKEY button. 16/JAN/2005 12:15 Scene No. 001 Title List 1/9 Start End 00:00:20 00:00:30 00:00:30 Edit Playlist HDD Start End Change MOVE 01 Cancel Playlist No.
Moving a Scene (Changing the Position of a Scene) 6 To setup, follow steps 1 to 3 in page 104. 4 Press the …† œ √ buttons to select the position to which you want to move the selected scene, then select the OK button. Edit Playlist Press the …† œ √ buttons to select the scene you want to move (change the position), then press the ANYKEY button. HDD Playlist No.
7 Adding a Scene Press the OK button at the end point of the scene. Add Scene HDD To setup, follow steps 1 to 3 in page 104. 4 01/JAN/2005 12:15 Scene No. 001 Press the …† œ √ buttons to select the scene that will have a new scene inserted before it, then press the ANYKEY button. Title List : 1/7 Start End 00:00:15 00:00:35 00:00:35 Start End Add Cancel MOVE SELECT RETURN EXIT Edit Playlist HDD 01 Playlist No.
Deleting a Scene Deleting a Playlist Entry from the Playlist To setup, follow steps 1 to 3 in page 104. 4 Using the PLAY LIST button Press the …† œ √ buttons to select the scene you want to delete, then press the ANYKEY button. Edit Playlist HDD 01 0:00:26 Play Playlist No. 1 02 0:00:07 03 00:06:04 04 1 With the unit in Stop mode/Playback mode, press the PLAY LIST button. The Edit Playlist screen is displayed.
3 Press the …† buttons to select Delete, then press the OK or √ button. • You will be prompted with the delete confirmation message “Do you want to delete?”. Copying from HDD to DVD Playlist HDD About the Copy Screen Do you want to delete? 16/JAN/2005 12:15 AV3 16/JAN/2005 12:15 Yes Copy No MOVE 4 Copy To : HDD ➞ DVD HDD 7 Scenes SELECT RETURN ! @ EXIT Press the œ √ buttons to select Yes, then press the OK button.
Using the TITLE LIST button 6 Press the ANYKEY button. Title List 1 Press the OPEN/CLOSE button and place a recordable disc on the disc tray. HDD Rename No. Protection 001 002 003 004 Copy Delete Edit √ Playlist √ Navigation √ 19/JAN/2005 12:15AV3 2 Press the OPEN/CLOSE button to close the disc tray. Wait until LOAD disappears from the front panel display. Check that the disc has enough available space for the recording.
- Copying a Title that has been edited once before - 9 The “Do you want to view screen of copying title?” message is displayed. -1 To begin high speed copy, press the œ √ buttons to select Yes, then press the OK button. High speed copy begins. The title to be copied is not played back, while the currently broadcasting programme is displayed on the screen. 10 Copy Copy To : HDD ➞ DVD HDD No. 1 Title Rec.
Changing the Record Mode To setup, follow steps 1 to 7 in page 110. 8 Press the √ and † buttons to select Rec. Mode, then press the OK button. Copying Multiple Titles at One Time Using the TITLE LIST button Copy Copy To : HDD ➞ DVD HDD No. 1 Title Rec.Mode 18/JAN/2005 12:15A LP ➞ HS Add a list Length 00:10:21 Start Rec. Mode XPAvailable [DVD] LPSP 04: 08:47 LP EP Total High 04: Speed 08:47 MOVE 9 SELECT RETURN Press the OPEN/CLOSE button and place a recordable disc on the disc tray.
6 9 Press the ANYKEY button. Title List HDD Rename No. Protection 001 002 003 004 Copy Delete Edit √ Playlist √ Navigation √ 19/JAN/2005 12:15AV3 19/JAN/2005 12:15 Title √ Select Media V-Mode Compatibility Disc Manager SP MOVE Length 18/JAN/2005 12:15A 19/JAN/2005 12:15A 20/JAN/2005 12:15A 25/JAN/2005 12:15A 00:10:21 00:40:03 00:20:15 00:50:16 Press the …† buttons to select Add, then press the OK button. Add Copy List screen is displayed.
Deleting an Undesired Title from the Copy List To setup, follow steps 1 to 7 in pages 112~113. 8 Press the …† buttons to select a title you want to delete from the copy screen. Previewing a Selected Title from the Copy List To setup, follow steps 1 to 7 in pages 112~113. 8 Press the …† buttons to select a title you want to preview in the copy screen. Copy Copy No. 1 2 3 Title Rec.Mode 18/JAN/2005 12:15A LP ➞ HS 19/JAN/2005 13:15A LP ➞ HS 20/JAN/2005 15:15A LP ➞ HS Add a list No.
Selecting Record Mode of Each Title from the Copy List Changing Record Mode of All Titles from the Copy List You can copy multiple titles while setting different record You can copy multiple titles while setting the same record modes for each title. mode for all titles. To setup, follow steps 1 to 7 in pages 112~113. To setup, follow steps 1 to 7 in pages 112~113. 8 Press the …† buttons to select a title to change its record mode in the copy screen. 8 Select the Rec.
Copying from DVD to HDD 4 Press the …† buttons to select the title you want to copy. ) To move to other pages, press the SKIP ( buttons. SKIP( ) : previous page of title list SKIP( ) : next page of title list 5 Press the ANYKEY button. Using the TITLE LIST button 1 2 Press the OPEN/CLOSE button and place a recorded disc on the disc tray. Title List DVD-RAM(VR) Rename No. Protection 001 002 003 004 Copy Press the OPEN/CLOSE button to close the disc tray.
8 After a successful copy, “The title is successfully copied.” message is displayed. Copying MP3 or JPEG Files from a Disc to HDD File Copy The title is successfully copied • Copying Multiple Titles at One Time – Same as an 1 2 HDD operation(See page 112) • Deleting an Undesired Title from the Copy List – Insert a JPEG disc or MP3 disc into the disc tray. Press the OPEN/CLOSE button to close the disc tray. Wait until LOAD disappears from the front panel display.
Folder Copy 4 Press the …† buttons to select the MP3 or JPEG files you want to copy, then press the ANYKEY button. 1 Insert a Disc (JPEG or MP3) into the tray. 2 Press the …† buttons to select Music or Photo, then press the OK or √ button. MP3 or JPEG folder is displayed. Music List CD » 02 : 10 Flower.mp3 .. Flower.mp3 Copy Play Mode √ MP3 Love.mp3 MP3 Straight from the heart.mp3 MP3 Run to you.mp3 Go01/15 To Playlist MP3 Heaven.mp3 New 4.0Playlist MB MP3 This Love.
■ Pressing the CANCEL button during folder copying will cancel the folder copying after the current file is copied. ■ Up to 1,500 files and 1,000 subfolders can be copied into one folder for MP3 files. ■ Up to 4,500 files and 1,000 subfolders can be copied into one folder for JPEG files. ■ Files having an existing name of ***.mp3/***.jpg, are automatically renamed to ***01.mp3/***01.jpg and copied. NOTE ■ It allows up to 999 copies to have the same name. ■ You cannot copy an Audio CD.
Disc Protection 3 Press the œ √ buttons to select Rename, then press the OK button. The Rename screen is displayed. Disc Protection allows you to protect your discs from being formatted or deleted due to unintended operations. Rename DVD-RAM(VR) Back Space Space Delete MOVE SELECT Clear RETURN Save 1 With the unit in Stop mode, press the ANYKEY button. EXIT Search Scene Navigation 4 Select the desired characters using the …† œ √ buttons, then press the OK button.
Formatting a Disc Use these instructions to format a disc. The disc protect should also be cleared. DVD-RW • You will be prompted with the confirmation message “Choose the recording format for DVD- RW.” Disc Manager DVD-RW(VR) Disc Name 1 With the unit in Stop mode, press the ANYKEY button. Used Space 00 : 10 : 32 Available Space 01 : 29 SP Choose the recording format for DVD-RW. Disc Protection Info Not Protected Current Rec.
Delete All Title Lists/Music Lists/Photo Lists 4 Press the œ √ buttons to select the Title, Music or Photo, then press the OK button. Title Disc Manager HDD 1 With the unit in Stop mode, press the ANYKEY button. [Title Partition] Used Space 00 : 10 : 32 Available Space 35 : 47 : 10 SP All title will be deleted.
• When Protected Entry exists: The Delete All Title List function will not operate. If there is a title containing a still picture, however, that function will not operate. If you want to delete a protected entry, disable Protect for it on the Lock item. • When protected a DVD-RAM is used, data cannot be deleted from a disc. Delete All Title Lists 1 With the unit in Stop mode, press the ANYKEY button. 4 Press the œ √ buttons to select Yes, then press the OK button. All title lists are deleted.
If you select Yes, you will be prompted again with the message “Disc will be finalised. Do you want to continue?”. Finalising a Disc After you record titles onto a DVD-RW/DVD-R disc with your HDD & DVD RECORDER, it needs to be finalised before it can be played back on external devices. Disc Manager DVD-RW(VR) Disc Name 00 : 10 : 32 Used Space Available Space 01 : 29 SP Disc will be finalised. Do you want to continue? Disc Protection Info Not Protected Current Rec.
Unfinalising a Disc (V/VR mode) 4 Press the œ √ buttons to select Yes, then press the OK button. The disc is unfinalised. ■ 1 With the unit in Stop mode, press the ANYKEY button. NOTE A DVD-RW can be finalised or unfinalised in Video mode. Mark Finalise Unfinalise DVD-Video(RW) DVD-RW(V) Additional recording, protection Operation Same as DVD-Video Search Scene Navigation and deletion are possible.
Reference Troubleshooting If your product malfunctions, go through the checkpoints below before contacting a Samsung authorised service centre. Power The input is displayed for a while when the power is turned on. Checkpoint 1 The HDD & DVD RECORDER requires some time to initialize and the input will be displayed for approx. 10 seconds after it is turned on. Recording Cannot record TV programmes. Checkpoint 1 Check whether the power cord is securely plugged into the power outlet.
Playback Cannot play the disc. Checkpoint 1 Checkpoint 2 Checkpoint 3 Check whether the disc is inserted correctly with the label facing up. Checkpoint 1 Check the regional code of the DVD disc. The angle operation is available only when the disc contains images captured from different angles. This HDD & DVD RECORDER cannot play some types of discs. (See pages 7, 47) icon appears on the screen. Checkpoint 1 The angle operation does not work while playing a DVD disc.
Video Timer Recording The disc revolves, but no image or bad quality images is displayed. Checkpoint 1 Be sure that the Video Setting is properly set. (See pages 40~41) Checkpoint 2 Check whether there is damage to or any foreign material on your disc. Checkpoint 3 Checkpoint 4 If scenes change from dark to bright suddenly, the screen may shake vertically temporarily, but this is not a fault. No sound.
Remote Control Unit Other problems. The remote control doesn't work. Checkpoint 1 Checkpoint 2 Checkpoint 3 Checkpoint 4 Point the remote control at the remote control sensor on your HDD & DVD RECORDER. Allow for proper distance. Remove obstacles between your HDD & DVD RECORDER and the remote control. Checkpoint 1 Read the table of contents and then find and read the section describing your problem, follow the instructions given. Checkpoint 2 Plug your HDD &DVD RECORDER off and on.
Specifications Power requirements AC 220-240V, 50Hz Power consumption 45 Watts Weight General Dimensions 4,2 Kg 430mm(W) x 255mm(D) x 79mm(H) Operating temp. +5°C to +35°C Other conditions Keep level when operating. Less than 75% operating humidity Input Video Composite Video : 1,0 V p-p at 75Ω load, sync negative Audio Max.
ELLAS (GREECE) Agaphtev pelavth, Saı eucaristouvme gia thn empistosuvnh pou deivxate sthn SAMSUNG me thn agorav authvı thı suskeuhvı. To proiovn autov thı SAMSUNG eivnai egguhmevno gia perivodo dwvdeka (12) mhnwvn apov thn hmeromhniva agoravı tou gia antallaktikav kai ergatikav. Sthn perivptwsh pou qa creiasteiv episkeuhv, to proiovn autov thı SAMSUNG qa prevpei na staleiv hv na metaferqeiv sto exousiodothmevno service, me evxoda tou agorasthv.
Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. ☎ 1-800-SAMSUNG (7267864) / www.samsung.
