instruction 0 RAM/nwm Manual 0 V I D E O DIGITALAUDIO www.samsung.
Getting Started tf this equipment does cause harmful interference to radio or TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reposition or relocate the receiving antenna.
Exterior interference such as lightning and static electricity can affect normal operation of this recorder. If this occurs, turn the recorder off and on again with the POWER button, or disconnect and then reconnect the | important Safety instructions AC power cord to theAC power outlet. The recorder wilt operate normally. • Be sure to remove the disc and turn off the recorder after use. Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below.
• Using CD-R/-RW • Use a 700MB(80 minutes) CD-PJ-RW disc. If possible, do not use a 800MB(90 minutes) or above disc, as the | Disc Storage Be careful not to damage the disc because the data on these discs are highly vulnerable to the environment. • Do not keep under direct sunlight. • Keep in a cool ventilated area. disc may not play back. • if the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early playback time, and all recorded files may not play.
, DVD-RW (Video mode) - This is a format that is used for recording data on a DVD-RW or DVD-R disc. The disc can be played by an existing DVD player once it has been finalized. - If a disc that has been recorded in Video Mode by a different manufacturer's recorder but has not been Disc use the following discs! product. When these discs are played, either "No Disc." or "The disc cannot be played. Please check the regional code of the disc." will be displayed.
mWarning ................................................................... 2 g Initial Setup .......................................................... 25 OSD Language Setup ............................................. 25 mPrecaution ............................................................... 3 Important Safety Instructions .................................. 3 g Using theSetup Menu ............................................. 25 Handling Cautions ...................................................
mRegion code (DVD-Video only) ............................... 45 gTroubleshooting ...................................................... 68 mLogos ofDiscs thatcanbeplayed .......................... 45 g Error Message Solutions ......................................... 70 mDisctypes thatcanbeplayed ................................. 45 gSpecifications ........................................................ 72 Discs ThatCannot bePlayed .................................. 46 gWarranty ..........................
A variety TheDVD-R155 allows youtorecord andplayhighquality digital video onDVD-RAM/DVD-RW/DVD-R discs. High quality digital audio and video recording and playback You can record up to approximately 16-hours of video on a double side 9.4 GB DVD-RAM disc,up to 15-hours on a dual-layer 8.5GB DVD-R disc, and up to 8-hours on a 4.
Make sure to check the following user's | Step I : Select the disc type before reading the manual Icon This unit can record on the following types of discs. Term If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a rewritable DVD-RW or DVD-RAM type disc. If you want to save the recording without making any Definition This involves a function available DVD RAM -RW RAM This involves a function available with DVD-RAM discs.
| Step 4 : Playing To start playback select the title you want to play from the Title list. A DVD consists of sections called titles, and sub sections called chapters. During recording, a title is created between two points where you start and stop recording. Chapters will be created automatically when you finalize recording on DVD-R/DVD-RW discs in Video mode. | Accessories Check for the supplied accessories below.
To determine whether your television is compatible, follow the instructions below. 1. S\,vitch your television on. 2. Point the remote control towards the television. 3. Press and hold the POWER button and enter the two-figure television by pressing the appropriate code simultaneously corresponding to the brand of your number buttons.
| Tour of the Remote Control You can contro! part of another manufacturer's TV functions with this remote control. • Buttons that can be controlled on your TV: POWER, INPUT SEL., TV VOL (+/-), TV CH (^ Iv), TV 100+. TV MUTE, 0~9, 9. STOP Button 17 Press to stop a disc or to stop the recording. 1 2 18 10. TV VOL Buttons 3 19 11. MENU Button Volume adjustment. -- 20 Brings up the DVD recorder's 12. ENTER/DIRECTION setup menu.
| Front Panel 0 0 1. 0 0 O POWER Button 00@ 8. Selects line input signal in external mode. (AVl, AV2, or DV) AV21N 9. Connects external equipment. 3. 11. STOP Button RSCAN Stops disc playback. Button OPEN/CLOSE scan mode. 12. PLAY/PAUSE Button Plays a disc or pauses playback. Button Opens and closes the disc tray. 7. 10. REC Button Starts recording. Selects the progressive 6. Uses this to set the desired Recording time and picture quality.
| Rear Panel @ 1. DIGITALAUDIO OUT(OPTICAL) Connects to an amplifier having a digita! optica! audio input jack. 2. DiGiTAL AUDIO OUT (COAXIAL) Connects to an amplifier having a digital coaxial audio input jack. 3. AVAUDIO 5. COMPONENT VIDEO OUT (excellent video quality) Connects to equipment having Component video input jacks. 7. AV 1AUDIO IN Connects the output of external equipment using audio cabtes OUT 8. Connects to the audio input of external equipment using audio cables. 4. 6.
If your TVhas a HDMI/DVI input, connect an HDMI/DVI cable to your TV You will enjoy the best quality image and sound. | Connecting to a TV with an HDIVll Jack Using an HDMI- HDMI cable (not included) connect the HDMI OUT jack on the rear of the DVD Recorder to the HDMI IN jack of your TV Press the input selector on your TV remote control until the HDMI signal from the DVD Recorder appears on your TV screen. J _z ii_!i! iii To watch through the HDMI output, set the digital audio output to PCM.
| Connecting to a TV with a DVl Jack Using an HDMkDVI cable (not included), connect the HDMI OUT terminal on the rear of the DVD Recorder to the DVI iN terminal of your TV. An HDMI to DVl connection requires a separate audio connection. Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD Recorder to the AUDIO (red and white) IN terminals of your TV. Turn on the DVD Recorder and TV. Press the input selector TV screen.
There are several ways to connect your DVD Recorder. Select one of the video connections pages. You must use one of the following audio/video | Connecting to Component connections on this unit. Video input Jacks (Y, PB,PR) _ 1. Connect the Component video cables(not supplied) between the COMPONENT OUT(Y, PB,PR)jacks on the DVD Recorder and COMPONENT IN(Y, PB,PR)jacks on your TV (or AV amplifier). This connection outputs the 480i or 480p resolution your TV. _ to 2.
| Connecting to an S=Video input Jack Connect an S-Video cable(not supplied) on your TV (or AV amplifier), between the S-VIDEO OUT jack on DVD Recorder and S-VIDEO iN jack S-VIDEO &.Video Cable _not . You will enjoy high quality images. S-Video separates the picture etement into black and white (Y) and color (C) signals to present clearer images than regular video input mode. This connection outputs the 480i resolution to your TV. .
| Connecting to a Video input Jack Connect a video(yellow) cable between the VIDEO(yellow) on the TV (or AV amplifier). -- AUDIO_ OUT jack on DVD Recorder VIDEO R Red'Whir __Yeilow AudioNJdeo Cable * You will enjoy normal quality images. This connection outputs the 480i resolution to your TV. * Connect the audio cables(white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on your TV(or AV amplifier).
Select one of the Audio connections on the following pages. | Connecting to your TV This connection will use your TV's speakers.
| Connecting to a Stereo Amplifier with Analog input Jacks If your stereo amplifier only has AUDIO INPUTjacks(L and R), use the AUDIO OUT jacks.
| Connecting to an AV Amplifier with a Digital input Jack if your AV amplifier has e Dolby Digital or DTS decoder and e digital input jack, use this connection. To enjoy Dolby Digital or DTS sound, you will need to set up the audio settings. (See page 30) m Optical Cable (not suppled) r-or--_ Coaxial Cable (not suppled) AVamplifier 3u_w0det Cente_ /S ...... % Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. ', ...............
This allows you to connect your DVD Recorder to other externa! devices and view or record their outputs. | Connecting a VCR, Set Top Box(STB) or DVD Player to the AV 1 IN or S-VIDEO IN jacks Connect the VCR or external device to the AV 1 IN jacks of the DVD Recorder. You can record from the connected equipment (VCR, STB or DVD Player). m Audio/Video S-Video Cable Cable •_-_ (not supplied) or _ VCR STB g The DVD-R155 does not have a TV tuner.
| Connecting a Camcorder You can record from connected equipment, the DVD Recorder. such as a cemcorder by using the AV 2 iN or DV IN jacks on front of Audio/Video Cable DV Cable R " VIDEO is'" _AU_O _ Camcorder (See page 39) _g When an Input source is inserted into AV 2 while watching TV, the input wilt be switched to AV 2 automatically. g If the input is not selected automatically, press the iNPUT SEL. button on the remote control to select the DV Input.
System Setup If you connected an external Audio System, turn on your Audio System and select AUX, CD or DVD. The OSD (On-Screen Display) displayed on the screen may vary depending on conditions such as the disc type and whether the disc has been inserted or not. | OSD Language Setup After piugging in the recorder, the first time you press the POWER button, the screen shown to the left appears. 1. Press the POWER button. 2. Press a number button to select the language.
i iiiiiii;iiii_ii_i!_i | ClVl Skip Time Setting When a program recorded on a DVD-RAM, a DVD-RW, DVD-VlDEO or a DVD-R is played, the unit can be set to automatically akip a portion of the program corresponding to a CM(commercial) Skip Time set by the user. 1. With a disc inserted and the unit in Stop mode, press the MENU button on the remote control. 2. Select Setup using the A T buttons, then press the ENTER or button. You can't use the Setup functions while playing a disc. 3. Select System button.
| EP Mode Time Setting You can set the EP (Extended Play) mode's time to 6 or 8 hours. 1. With a disc inserted and the unit in Stop mode, press the MENU button on the remote control. 2. Select Setup using the A v" buttons, then press the ENTER or button. You can't use the Setup functions while piaying a disc. 3, Select System button. using the A v buttons, then press the ENTER or 4, Select desired or _ button. option using the A _' buttons, then press the ENTER EP Mode Time will be displayed. 5.
| Quick Recording Setting It takes about 10 seconds for s disc to load (initialize) every time you turn on the unit. To bypass this initialization process, you can set the Quick Recording feature to On. This enab/es you to record immediately without having to wait for the disc to load. 1. With a disc inserted and the unit in Stop mode, press the MENU button on the remote control. 2. Select Setup using the A _' buttons, then press the ENTER or button. You can't use the Setup functions while playing a disc.
Bypressing thePlaybutton oftherecorder while watching TV,the TVscreen willchange totheptayscreen. IfyouplayaDVD when theTVpower isoff,theTVwiltpower On. IfyouturntheTVoff,theDVD Recorder willpower off automatically.(When theDVD recorder isrecording, itcan'tbe powered off.) ! Ifyouchange HDMI toother sources(Composite, Component, RF... etc)onyour TVwhile playing aDVD disc,theDVDRecorder wiltstopplaying. TheDVDRecorder maykeep playing certain discs based ontheircontent.
You can connect the DVD-Rf55 ' Home Theater system. to an external audio amplifier or a This allows you to setup the audio device and sound status settings depending on the audio system in use. 1. With the unit in Stop mode/No Disc mode, press the MENU button on the remote control. 2. Setect Setup using the ,& v buttons, then press the ENTER or button. 3. Select Audio button. using the A T buttons, then press the ENTER or m,, 4.
This allows you to set up the TV screen settings. | TV Aspect 1. With the unit in Stop mode/No Disc mode, press the MENU button. 2. Select Setup using the J, T buttons, then press the ENTER or D,, button. 3. Select Video using the A v' buttons, then press the ENTER or _- button. 4. Select TV Aspect using the A v' buttons, then press the ENTER or _. button. 5. Select the desired item(4:3 Letter Box, 4:3 Pan-Scan using the ,& T buttons. Then press the ENTER or _ button.
i iiiiiii;illi_ii_i!_i | HDIVlI/DVI Resolution This setting is used when the unit is connected Display devices (TV, projector, etc). by HDMI or DVI to • 480p : 720 x 480 • 720p : 1280 x 720 ,, 1080i : 1920 x 1080 • Connect the DVD-R155 to HDMI or DVI. to your TV via HDMI or DVI. Set your TV's input Press the P.SCAN button while the unit is in stop mode to select the output resolution.
| Setting the Rating Level t. Select Rating Level using the ,L T buttons. 2. Press the ENTER or _* button. 3. Select the desired Level you want using the A _ buttons, then press the ENTER or _ button. For example, if you select up to Levet 6, discs that contain Level 7, 8 will not play. A higher number indicates that the program is intended for adult use only. | Changing the Password 1. Setect Change Password using the A _' buttons. 2. Press the ENTER or _ button.
This section explains various DVD recording methods. This unit can record on various types of discs. Before recording, read the following instructions and select the disc type according your preference. to This recorder can record on the following discs. DVD-RAM RAM • DVD-RWs and DVD-RAMs • DVD-Rs are non-rewritable DVD-RW DVD-R RW R are rewritable.
DVD-RAM iil;ii Since available functions differ depending on the disc type, select s disc that best fits your preferences. When you insert an unused disc, the following message appears. • DVD-RAM : Use after formatting the disc. • DVD-RW : Use after initializing the disc. You can change the mode of DVD-RW disc. Refer to Formatting a Disc on page 65. • DVD-R : Formatting disc is unnecessary.
Videos with copy protection cannot be recorded on this DVD Recorder. When the DVD Recorder receives a copy guard signal while recording, recording stops and the following message appears on the screen. Concerning Copy Control Signals TV broadcasts that contain copy control signals may have one of the following three signal types, COPY-Free, Copy-Once and Copy-Never. If you want to record a copy-once type program, use a DVD-RW disc with CPRM in VR Mode. You can also use DVD-RAM discs.
| About the INFO Button • _FLFC_ NFO NPUT The INFO function allows you to view the current status and SEL progress of playback and recording. When recording on a used disc, make sure that there is enough disc space for recording. o i°® 0 © @ ® ® • Press the INFO button. The disc information -C -@ -@ -@ display window appears. 1 .Disc Type 2. Current information display status 3. Disc Name 4. Total Title : Total number of titles 5. Total Playlist : Total number of Playlists 6.
iiiiiiiiiiiiiii;iiii!_;ii:ii:i!!!i!i!i_iii:iil; Before you start • Check that the disc has enough available Adjust the recording mode. 1. Press the OPEN/CLOSE disc tray. button and place a recordable disc on the 2. Press the OPEN/CLOSE button to close disc tray. Wait until "LOAD" disappears from the front panel display 3. Press the INPUT SEL. button to select the input source according to the connection you made. The front panel display changes in the following sequence: AV1 -->AV2 --> DV ] 4.
You may control a Digital Camcorder using the IEEE1394 (DV) interface. Before you start Check that the disc has enough available space for the recording. Adjust the record mode. See page 24 to see how to connect the camcorder to your DVD recorder. 1. Press the OPEN/CLOSE disc tray. button, and ptace a recordable disc on the 2. Press the OPEN/CLOSE button to close the disc tray. Wait until "LOAD" disappears from the front panel disptay. 3. Press the RED MODE button repeatedly speed(quality).
iiiiiiiiiiiiiii;iiii!_;ii:ii:i!!!i!i!i_iii:iil; You can set the DVD Recorder to record in preset pressing the REC button repeatedly. increments by 1. If you want to record from a connected external component, press the iNPUT SEL. button to setect an appropriate external input(AV1, AV 2 or DV). 2. Press the REO button to start recording. 3, Press the REO button to adjust the recording time.
You need to set the Clock (Setup - Clock Set) before proceeding with a timer recording. (See page 29) 1. Press the OPEN/CLOSE disc tray. button, and place a recordable disc on the 2. Press the OPEN/CLOSE button to close the disc tray. Wait until "LOAD" disappears from the front panel display. If an unused DVD-RW disc is inserted, a message asking whether to initialize the disc or not will appear. (See page 35) 3, Press the MENU button in Stop mode. You can also set a timer recording via the TIMER button.
= If the timer settings overlap The first program has priority. After recording of the first program is complete, the second program starts being recorded. = The timer recording may be different from the actual set time depending on the disc and the timer recording status(for example, recording times overlapping, or if the previous recording ends within 3 minutes of the start of the next recording.). Qwitl start blinking if Timer Recording is not ready to start.
You can delete the timer record menu. list using the scheduled record list 1. Press the MENU button in Stop mode. 2. Press the A _' buttons to select Timer ENTER or I_ button. Rea., and then press the 3, Press the A T buttons to select Scheduled Record List, and then press the ENTER or _ button. 4, Press the A T buttons to select the number of the timer recording you want to delete, and then press the ENTER or _ button. The Edit and Delete items are displayed. 5.
iiiiiiiiiiiiiii;iiii!_;ii:ii:i!!!i!i!i_iii:iil; iiiili_i_i_i_i_i_i_!_i!i!i!i!i!i!i!iiii_iiii:ii!ii' iiiiiiiiiiii!i!i!ii!!i!_i_iiiiiiii /_ This function sl/ows you initialize _ and Finalize a disc automatically. 1. With the unit in Stop/No Disc mode, press the EZ RED MODE button on the remote control. 2. Press the ,,q _ buttons to select On, and then press the ENTER button. The EZ REC MODE is set up. 3. Insert a disc. If the disc is new, it will initialize automatica!ly. 4. Press the REC button. 5.
Playback This section introduces playback Read the following (_ basic playback functions end by disc type. information before playing e disc. Disc Types Disc Logo Max. Playing Time Singlesided(5") 240min DVD- _ VIDEO Doublesided(5") 480min VIDEO _ AUDIO Singlesided(3.5") 80min Doublesided(3.5") 160min Singlesided(5") 74min Singlesided(3.5") 20min coded Both the by DVD region. recorder These and regional the discs codesaremust match in order for the disc to play.
| Discs That Cannot be Played - DVD-Video with a region number other than "1" or "ALL" • 5" 2.6 GB and 5.2 GB DVD-RAM - 3.9 GB DVD-R Disc for Authoring. • A DVD+R/DVD-RW(V) disc which has been recorded and not finalized in a different manufacturer's recorder. • PALdiscs • DVD-ROM/PD/MV-Disc, etc. • Video CD/CVD/SVCD/CD-ROM/CDV/CD-G/CDd • MPEG4 Discs. m This DVD recorder can only operate with discs that are compatible with DVD-RAM Standard Version 2.0.
| Using the Disc Menu & Title Menu Some discs contain a dedicated menu system that allow you to select special functions for the title, such as chapters, audio track, subtitles, film previews, information on characters, etc. For DVD-VIDEO Discs Disc Menu : Press the DiSC MENU button to enter the disc's menu. • Move to the setup menu related to the playback operation. • You can select the audio language and the subtitles provided by the disc.
g Nosound isheard during Scan(Search) mode except fast playback (1.7X speed) mode. g ForCD(CD-DA), Youcanhear sound during Scan mode. g Thespeed marked while scanning maybedifferent fromthe actual playback speed. Searching Chapters or Tracks During playback, press the SKIP( Q (_) button on the remote control. • tf you press the SKIP( _ ) button, it moves to the beginning of the chapter or track or marker (DVD-RAM,DVD-RW(VR mode).
| Using the ANYKEY Button The ANYKEY function allows you to easily search for a desired scene by accessing title, chapter, track, and time. You can also change the subtide and audio settings and set some features including Repeat, Angle, and Zoom. Moving to a Desired Scene Directly If you want to move to e certain function. 1. Press the ANYKEY title, chapter or time use this button during playback. 2. Press the A T buttons to select the Title, Chapter or Time.
Selecting the Subtitle (VRmode) Subtitle languages may not work depending only available during playback. 1. Press the ANYKEY on the disc type. This is button during playback. 2. Press the A v buttons to select Subtitle select the desired subtitle language. and press the _ _ buttons to g If the subtitles overlap, disable the caption function on your TV. g Some discs anew you to select the language for the disc menu only. g To make the screen disappear, press the ANYKEY again.
Zooming-In N,N 1. Press the ANYKEY button ;.... during playback or pause. 2. Press the A V' buttons to select Zoom, and then press the ENTER button. ( ¢, ) will be displayed. 3, Press the A '_",_ m,,buttons to move to the area you want to enlarge. 4, Press the ENTER button. normal size --> 2X --> 4X --> 2X --> normal size Using Bookmarks (V mode) This feature lets you bookmark sections (V mode), so you can quickly find them. Setting ofa DVD or DVD-R/-RW Bookmarks 1.
• Clearing abookmark 1.Press theMARKER button during playback 2.Press the_11_buttons toselect a bookmarked scene. 3. Press the CANCEL button to delete the selected bookmark. Using Markers • (VR mode) Setting Markers 1. Press the MARKER button during playback. 2. Press the ENTER button when the desired scene appears. The number 01 is displayed and the scene is memorized. 3. Press the _1 _ button to move to the next position. 4, Press the ENTER button when the desired scene appears.
Buttons --® $_,Ol r? m® m® ®-- on the Used for CD Playback 2. _ : Plays the selected track (song). 3. ENTER( _ ) button 4. RETURN( belongs. © } button: ) button : Plays the selected track (song). Moves to the folder to which the current song : Plays the next track. 6. SKIP((_) button : Returns to the beginning of the current track when pressed during playback, tf pressed again, your DVD recorder moves --(2D d) Control 1. _, V : Selects a track (song). 5.
| Playing an IVIP3 Disc 1. Insert an MP3 disc into the disc tray. And press the ,_ 'V buttons to select Disc Navigation, the ENTER or m,.button. 2. Press the A • button. and then press buttons to select Music, and then press the ENTER or The MP3 menu appears and the tracks(songs) automatically. are played 3. Press the A T buttons to select the track (song) you want to hear, and then press the ENTER button or _ button. ©@ @ -C • MP3 Screen Elements 1. PLAY MODE icon 2.
Play Option Mode iYiiii_ 1, During Stop, Press the ANYKEY highlighted. • During Playback, button. The Play option will be Repeat Mode will be highlighted. 2. Select a desired ptay option (Normal, Random, Intro or Ptaytist) using the _1 _ buttons. Press the ENTER button. ,, Normal : Tracks on a disc are played in the order in which they were recorded on the disc. ,, Random[R] : The Random option plays the disc's tracks in random order.
5-1.Ifyoupress thePLAY((_)) button, theSlide show screen willappear. Thepicture interval (Slide show speed) must beset. 5-2.Press theENTER button withapicture selected intheAlbum screen andselect adisplay mode (Album screen (_), Slideshow(_ ), Rotation (_) orZoom(& ))using the__,-buttons, thenpress theENTER button. :Returns totheAIbum screen. :Theunitenters slideshow mode. Before theslide show canbegin, thepicture interval (Slide show speed) must beset.
This section introduces basic functions of DVD editing. , Title List A titie is a section of recorded video and audio. The Title List shows a list to help you select a titie. If one title is deleted from the title list, that title cannot be played again. • Playlist This refers to a unit of playback, which is made by selecting a desired scene in the entire Title List. When one playlist is ptayed, only the scene selected by the user witl play and then stop.
| Locking (Protecting) Follow these instructions accidental deletion. a Title to lock an entry to protect it from 1. Press the TITLE LIST button. The Title List screen is displayed. Or use the MENU button. • Press the MENU button. • Press the h, T buttons to select Title List, and then press the ENTER or _ button twice. 2. Press the A • buttons to select an entry you want to protect from the Title List, and then press the ENTER or D,-button. 3.
| Deleting a Section of a Title (VR mode) Follow these instructions to delete e section of a Title List entry. 1. Press the TITLE LiST button. The Title List screen is displayed. Or use the MENU button. • Press the MENU button. • Press the A T buttons to select Title List, and then press the ENTER or _ button twice. 2. Press the A T buttons to setect an entry you want to edit from the Title List, and then press the ENTER or _ button. 3.
,| Creating a Playlist U Follow these instructions recorded title. to create a new playlist (VR mode) entry from a 1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the ,A T buttons to select Playlist, I_ button. and then press the ENTER or 3. Press the A _' buttons to select New Playlist, and then press the ENTER or _ button. The Make Scene screen is displayed. 4. Press the ENTER button at the start point.
| Renaming a Playlist Entry (VR mode) Follow these instructions title ors playlist entry. to rename a playlist entry, i.e. to edit the 1. With the unit in stop mode, press the PLAY LiST button. The Edit Ptaylist screen is displayed. 2. Press the A V" buttons to select the title you want to edit from the Ptaylist, and then press the ENTER or I_ button. 3, Press the A _' buttons to select button. Rename, and then press the ENTER 4, Enter the desired characters using the A T ,41!_ buttons.
Modifying a Scene (Replacing a Scene) Follow steps I to 3 of Editing a Scene for the P/aylist on page 61. 4, Press the A T .,_ _ buttons to select the scene you want to modify, and then press the ENTER button. 5. Press the ,A '_' buttons to select Modify, button. and then press the ENTER 6, Press the ENTER button at the start point of the scene. • The image and starting point time are displayed on the Start window.
Adding a Scene Fo#ow steps I to 3 of Editing a Scene for the PIsyfist on page 61. 4. Press the A T .,4 _ buttons to select the scene that will have a new scene inserted before it, and then press the ENTER button. A yellow selection window is displayed on the scene to be added as the new scene. 5. Press the A V buttons to select Add, then press the ENTER button. 6, Press the ENTER button at the starting point of the scene. • The image and starting point time are displayed on the Start window.
| Copying a Playlist Entry to the Playlist t. Press the PLAY LiST button. The Edit Piaylist screen is displayed. 2. Press the A T buttons to select the title you want to copy to the Ptaylist, and then press the ENTER or _, button. 3. Press the A T buttons to select Copy, and then press the ENTER button. Ptaylist that has been selected will be copied. g The playlist can contain up to 99 ptaytist entries (titles). | Deleting a Playlist Entry from the Playlist 1.
| Disc Protection DNc Protection allows you to protect your discs from being formatted or deleted due to unintended operations 1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the A T buttons to select Disc Manager, ENTER or _ button. and then press the 3, Press the A T buttons to select Disc Protection, ENTER or _ button. then press the 4. Press the A v' buttons to select Protected, then press the ENTER button.
| Finalizing a Disc After you record titles onto e DVD-RW/DVD-R disc with your DVD recorder, it needs to be finalized before it can be played back on external devices. 1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the A T buttons to select Disc Manager, ENTER or _ button. 3. Press the A T buttons to setect Disc Finalize, ENTER or _ button. and then press the and then press the 4. Press the ,,_ _ buttons to select Yes, then press the ENTER button.
| Delete All Title Lists The disc protection should be disabled first. 1. With the unit in Stop mode, press the MENU button on the remote control. 2. Press the A T buttons to select Disc Manager, ENTER or _ button. and then press the 3, Press the A T buttons to select Delete All Title Lists, and then press the ENTER or !_ button. • When Protected Entry exists: The Delete All Title List function will not operate. If you want to delete a protected title, disable Protection for it on the Lock item.
Play mode settings are different from the settings configured in the Settings menu. If your product malfunctions, go through the checkpoints below before contacting a Samsung authorized service center. The disc does not support all selected functions. In this case, some settings configured in the settings menu may not work properly. | Power The input is displayed turned on. for a while when the power is Cannot change the aspect ratio. The aspect ratio is fixed for DVD discs.
Abnormal | Sound HDMI output screen. If snow noise appears on the screen, No sound. Are you watching mode? it means that the TV does not support HDCP (High-bandwidth Digital Content Protection). a program in scan If you are playing a program at a speed other than normal and fast1 speed, the sound will not be heard. HDMI output Jitter Check if your TV system is setup correctly. Check the connections and settings.
Before contacting a Samsung authorized service center, perform the following simple checks. Error Message Solution You cannot record a copy protected movie. / Explanation • You can't record the video since it is protected by copyright. • The disc you are using is protected. To record on this disc or use this function, disable the disc protection function. Refer to page 65. You cannot record. This disc is protected. This disc cannot be formatted (the disc is protected).
Error Message Solution / E×planation • Error is detected on the disc. System error is found. Please try it again after turning off the power, The DV device is not connected. You can't use the disc because it contains errors from previous recordings. Use the disc after formatting. When operating, errors happen. Turn off the device. (To turn off, press and hold the power button on the front of the device for 10 seconds.) After turning off, press the Open button and remove the disc from the device.
Power requirements 120V AC, 60Hz Power consumption 19 Watts 5.1 tb Weight General Dimensions Operating 16.9 in(W) x 8.5 in(D) x 1.9 in(H) +41°F to +95°F temp. Other conditions Keep level when operating. Less than 75% operating humidity Video (1,2) 1.0 V p-p at 750 toad, sync negative S-Video input (Y: 1.0Vp-p, C: 0.286Vp-p at 75£2 toad) input Audio(1,2) Max.
This SAMSUNGbrand product,as suppliedand distributedby SamsungElectronicsAmerica,Inc. (SAMSUNG)and deliverednew, in the originalcartonto the originalconsumerpurchaser,is warrantedby SAMSUNGagainstmanufacturingdefectsin materialsandworkmanshipfor a limitedwarrantyperiodof: One (1) Year Parts / Ninety (90) days Labor (90 days Partsand Labor for Commercial Use) This limitedwarrantybeginson the originaldateof purchase,and is validonlyon productspurchasedand usedin the UnitedStates.
ContactSAMSUNG WORLDWiDE Ifyouhaveanyquestions orcomments relating toSamsung products, please contact theSAMSUNG customercarecenter. Region North America Country CANADA MEXICO U.S.A Europe CIS Asia Pacific Middle East & Africa Care Center 1-800-SAMSUNG (7267864) 01-8O0-SAMSUNG (7267864) 1-800-SAMSUNG (7267864 0800-333-3733 0800-124-421 Web Site www.samsung.com/ca www.samsung.com/mx 800-726-7864(SAMSUNG) 0-800-507-7267 1-800-10-7267 www.samsung.com www.samsung.com/ar www.samsung.com/br www.
HEADQUARTE RS 105 Challenger Road, Ridgefield Park, N.J.07660-0511 TEL: 1-800-SAMSUNG SERVICE DIVISION 400Valley Road, Suite 201 Mount Arlington, NJ07856 1-800-SAMSUNG (726-7864) www.samsung.
