00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 1 Manuel d'instructions DVD-V5650 CA AK68-00956G.01 www.samsung.
00956G V5650 XAC_Fra1 01 14/3/06 CONSIGNES 10:27 Page 2 DE SÉCURITÉ Consignes de sécurité importantes 1) Lisez attentivement chacune des consignes énumérées ci-dessous. 2) Conservez ces consignes dans un lieu sûr. 3) Faites attention à tous les avertissements et à toutes les mises en garde. 4) 5) 6) 7) Assurez-vous de bien suivre toutes les instructions d’utilisation. N’utilisez pas cet appareil près de l’eau. Utilisez un chiffon sec seulement pour épousseter cet appareil.
00956G V5650 XAC_Fra1 01 14/3/06 CONSIGNES 10:27 Page 3 DE SÉCURITÉ Précautions POUR ÉVITER LE RISQUE D’UN CHOC ÉLECTRIQUE, NE JAMAIS RETIRER LE CAPOT DE L’APPAREIL. AUCUN ÉLÉMENT NÉCESSAIRE À L’UTILISATEUR N’EST PLACÈ À L’INTÉRIEUR DE L’APPAREIL. RÉFÉREZ-VOUS AU SERVICE APRÈSVENTE ET CONSULTEZ UN TECHNICIEN QUALIFIÉ EN CAS DE BESOIN. Ce symbole indique la présence d’une haute tension électrique à l’intérieur de l’appareil qui risque de provoquer un choc électrique et des dégâts corporels.
00956G V5650 XAC_Fra1 01 14/3/06 CONSIGNES 10:27 Page 4 DE SÉCURITÉ ATTENTION CE PRODUIT UTILISE UN FAISCEAU LASER. EN OPÉRANT UN CONTRÔLE, UN AJUSTEMENT, OU TOUTE PROCÉDURE AUTRE QUE CELLES INDIQUÉES DANS CE MANUEL, VOUS VOUS EXPOSEZ À DES RADIATIONS DANGEREUSES. NE JAMAIS OUVRIR LE CAPOT ET NE PAS ESSAYER DE RÉPARER LE LECTEUR VOUS-MÊME. TOUTE RÉPARATION DOIT ETRE EFFECTUÉE PAR UN TECHNICIEN QUALIFIÉ. Remarque: • Cet appareil ne fonctionne qu’avec une alimentation électrique en 120 V c.a., 60 Hz.
00956G V5650 XAC_Fra1 01 14/3/06 A VA N T 10:27 Page 5 DE DEMARRER Avant de démarrer Accessoires Remote Control (AK59-00051A) Piles 2EA 1,5V(AAA) (AC43-12002H) Video/Audio Cable (AC39-00073A) Câbled’antenne (AC39-42001J) Manuel d'utilisation' (AK68-00956G) Insertion des piles dans la télécommande 1 Ouvrez le couvercle du compartiment des piles situé à l’arrière de la télécommande. 2 Placez deux piles AAA. Assurez-vous que les polarités (+ et -) sont correctement alignées.
00956G V5650 XAC_Fra1 01 14/3/06 TA B L E DES 10:27 Page 6 M AT I E R E S Table des matières Consignes de sécurité ..................................................................................................................................2 Consignes de sécurité importantes ......................................................................................................2 Précautions ............................................................................................................
00956G V5650 XAC_Fra1 01 14/3/06 TA B L E DES 10:27 Page 7 M AT I E R E S Chapitre 4 : Fonctionnement du lecteur DVD Lecture d’un disque ....................................................................................................................................31 Utilisation des fonctions Recherche et Saut ................................................................................................33 Utilisation de la fonction Affichage Pendant la lecture d’un DVD/VCD/CD/MPEG4 ............
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 8 Chapitre 1 C O N F I G U R AT I O N General Features Remarque Ce produit comporte une technologie protégée contre la reproduction par l’office des brevets des Etats-Unis et par la propriété intellectuelle. L’utilisation de cette technologie protégée contre la reproduction doit être autorisée par Macrovision et elle est conçue pour un usage domestique et autre visualisation limitée uniquement, sauf autorisation contraire de la part de Macrovision.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 9 C O N F I G U R AT I O N Type de disque et caractéristiques Ce lecteur DVD peut lire les types de disque suivants ayant les logos correspondants : Types de disque (logos) Types d’enregistrement Taille du disque Temps maxi. de lecture 5” Une face 240 min. Deux faces 480 min. 3 1/2” Une face 80 min. Deux faces 160 min. DVD Audio + Vidéo VIDEO-CD AUDIO-CD ■ ■ Audio + Video 5” 74 min. 20 min. 3 1/2” 5” 74 min. 3 1/2” 20 min.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 10 C O N F I G U R AT I O N Description Commandes en façade 1 4 1 2 3 4 5 6 7 8 9 2 5 6 8 7 TIROIR DISQUE Placez le disque ici. Fente du magnétoscope Insérez-y une cassette vidéo VHS standard.. EJECT Pour éjecter une cassette vidéo lorsqu’elle est arrêtée.. POWER Permet d’activer et de désactiver le lecteur DVD-magnétoscope. LINE IN 2 Pour connecter à la prise de sortie vidéo/audio de votre périphérique externe. P.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 11 C O N F I G U R AT I O N Panneau arrière ❶ ❷ ❸ ❹ ➎ ❻ 1 2 e. 3 ❼ AUDIO OUT Pour connecter aux prises d’entrée audio de votre téléviseur. Vous pouvez l’utiliser comme borne de sortie audio lorsque le câble Component (Composant) ou S-Video (S-Vidéo) est branché. COMPONENT VIDEO OUT - Utilisez ces prises si vous possédez un téléviseur avec les prises entrée Component Video. Ces prises permettent une vidéo PR, PB et Y.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 12 C O N F I G U R AT I O N Aperçu de la télécommande 1 Bouton POWER Permet d'allumer et d'éteindre le lecteur DVD-magnétoscope. 2 Boutons CHIFFRE 3 Bouton AUDIO Permet d'accéder aux différentes fonctions audio d'un disque. (lecteur DVD) 4 Bouton (Sauter) Actionnez ce bouton pour effectuer des recherches/sauts en arrière sur un disque. Permet de sauter un titre, un chapitre ou une plage sur un disque.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 13 Chapitre 2 BRANCHEMENTS Branchement du câble d’antenne Il existe plusieurs manières de connecter votre lecteur DVD-magnétoscope. Sélectionnez l’une des connexions d’antenne suivantes correspondant le mieux à celles ci-dessous.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 14 BRANCHEMENTS Méthode 2 : Antenne + lecteur DVD-magnétoscope + TV : Boîte de jonction avec plusieurs chaînes cryptées Wall Vous pouvez enregistrer des chaînes en sélectionnant la chaîne sur la boîte de jonction. Vous ne pouvez pas enregistrer une chaîne lorsque vous en regardez une autre. Assurezvous que la boîte de jonction est activée.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 15 BRANCHEMENTS Avant le branchement du lecteur DVDmagnétoscope - Désactivez toujours le lecteur DVD-magnétoscope, le téléviseur et autres composants avant de connecter ou déconnecter des câbles. - Reportez-vous au manuel d'utilisation des composants supplémentaires que vous connectez (un téléviseur par exemple) pour plus d'informations concernant ces composants particuliers.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 16 BRANCHEMENTS Connexion à un téléviseur (S-Vidéo) - Connexion à votre téléviseur à l'aide d'un câble S-Vidéo. - Vous visualiserez des images d'une qualité supérieure. S-Vidéo sépare l'élément image en signaux noir et blanc (Y) et couleur (C) afin de proposer des images plus nettes que le mode d'entrée vidéo habituel. (Des signaux audio sont émis via la sortie audio.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 17 BRANCHEMENTS Connexion à un téléviseur (mode Entrelacé) - Connexion à votre téléviseur à l'aide des câbles vidéo composants. - Vous visualiserez des images d'une qualité supérieure et des images à la reproduction couleur précise. Le vidéo composant sépare l'élément image en des signaux noir et blanc (Y), bleu (PB) et rouge (PR) afin de proposer des images claires et nettes. (Des signaux audio sont émis via la sortie audio.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 18 BRANCHEMENTS Connexion à un téléviseur (mode Progressif) 1 A l’aide de câbles vidéo composants (non fournis), connectez la borne COMPONENT VIDEO OUT située à l'arrière de votre lecteur DVD-magnétoscope à la borne COMPONENT IN de votre téléviseur. 2 A l’aide des câbles audio, connectez les bornes AUDIO (rouge et blanche) OUTsituées à l'arrière du lecteur DVD-magnétoscope aux bornes AUDIO (rouge et blanche) IN de votre téléviseur.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 19 BRANCHEMENTS Connexion à un système audio Connexion à un système audio (amplificateur 2 voies) 1 A l’aide des câbles audio, connectez les bornes AUDIO (rouge et blanche) OUT (LINE) situées à l'arrière du lecteur DVD-magnétoscope aux bornes AUDIO (red and white) IN de votre amplificateur.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 20 BRANCHEMENTS Connexion à un système audio (amplificateur Dolby digital, MPEG2 ou DTS) 1 A l’aide d'un câble coaxial (non fourni), connectez la borne DIGITAL AUDIO OUT (COAXIAL) située à l'arrière de votre lecteur DVD-magnétoscope à la borne DIGITAL AUDIO IN (COAXIAL) de votre amplificateur.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 21 BRANCHEMENTS Connexion d'un câble d’alimentation et configuration automatique 1 Le câble d'alimentation de votre lecteur DVDmagnétoscope doit être branché à une prise murale standard de 120 V/60 Hz. Evitez d'actionner des boutons de votre télécommande ou de l'unité lors de la configuration automatique. Lorsque votre lecteur DVD-magnétoscope fonctionne en mode de configuration automatique, “Auto” clignote.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 22 Chapitre 3 C O N F I G U R AT I O N I N I T I A L E Sélection d’une langue de menu Pour changer la langue du MENU d'affichage à l'écran en anglais, français ou espagnol, respectez les étapes suivantes. 1 Appuyez sur le bouton MENU. 2 Appuyez sur les boutons "/# pour sélectionner Setup, puis appuyez sur le bouton % ou ENTER. Réglage Initial SETUP Langue DVD VCR : Français L’horloge Chaînes Affi.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 23 C O N F I G U R AT I O N I N I T I A L E Réglage de l’horloge Ce menu sert à régler l'heure actuelle Vous devez régler l'heure afin de pouvoir utiliser l'enregistrement programmé. Réglage automatique de l’horloge 1 Appuyez sur le bouton MENU. 2 Appuyez sur les boutons "/# pour sélectionner Setup, puis appuyez sur le bouton % ou ENTER. Réglage Initial SETUP Langue VCR Affi.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 24 C O N F I G U R AT I O N I N I T I A L E 6 Appuyez sur les boutons "/# pour sélectionner Fuseau Horaire, puis appuyez sur le bouton % ou ENTER. Fuseau Horaire Fuseau horaire : Automatique %! Automatique Atlantic Eastern Central Sélectionnez le fuseau horaire correspondant à votre zone à l'aide des boutons ",$&% puis appuyez sur le bouton ENTER. Sélectionnez Automatique pour régler le fuseau horaire automatiquement.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 25 C O N F I G U R AT I O N I N I T I A L E 2 Appuyez sur les boutons "/# buttons to select Setup, then press the % ou ENTER. Réglage Initial SETUP Langue DVD VCR : Français L’horloge Chaînes Affi. du Panneau Coupure Auto % % % : Auto : Non % % PROG FUNC ENTER 3 Appuyez sur les boutons "/# pour sélectionner L’horloge, then press the % ou ENTER. RETURN MENU Réglage Initial SETUP Langue DVD VCR : Français L’horloge Chaînes Affi.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 26 C O N F I G U R AT I O N I N I T I A L E Mémorisation des chaînes Sélection de la source du signal vidéo Cette fonction vous permet de régler manuellement la bande du tuner de votre lecteur DVD-magnétoscope sur l'antenne ou le réseau câblé, en fonction du système que vous avez relié à la prise d’entrée de l'antenne au cours de la configuration initiale. N'utilisez ce réglage que si la configuration automatique a détecté une bande du tuner incorrecte (ex.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 27 C O N F I G U R AT I O N I N I T I A L E Enregistrement des chaînes dans la mémoire (méthode automatique) La mémorisation automatique des chaînes recherche et enregistre automatiquement toutes les chaînes actives de votre zone. 5 Appuyez sur les boutons "/# pour sélectionner Prog. Auto des Chaînes, puis appuyez sur le bouton % ou ENTER.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 28 C O N F I G U R AT I O N I N I T I A L E Sélection du canal de sortie RF Utilisez cette fonction si votre lecteur DVD-magnétoscope est relié au téléviseur au moyen d'un câble d'antenne RF (fréquence radioélectrique). 1 Appuyez sur le bouton MENU. 2 Appuyez sur les boutons "/# pour sélectionner Setup, puis appuyez sur le bouton % ou ENTER.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 29 C O N F I G U R AT I O N I N I T I A L E Sélection de l’affichage façade Vous pouvez régler l'affichage façade de façon à ce que celui-ci soit en mode Forte Luminosité ou en mode Faible luminosité en permanence ou qu'il sélectionne automatiquement le mode Faible luminosité lorsque l'appareil est hors tension. 1 Appuyez sur le bouton MENU. 2 Réglage Initial Appuyez sur les boutons "/# pour sélectionner Setup, puis appuyez sur le bouton % ou ENTER.
00956G V5650 XAC_Fra1 01 14/3/06 10:27 Page 30 C O N F I G U R AT I O N I N I T I A L E Réglage de la mise hors tension automatique Cette fonction permet d'éteindre automatiquement votre lecteur DVD-magnétoscope si aucun signal n'est reçu ou si vous n'appuyez sur aucun bouton pendant une durée déterminée. 1 Appuyez sur le bouton MENU. 2 Réglage Initial Appuyez sur les boutons "/# pour sélectionner Setup, puis appuyez sur le bouton % ou ENTER. SETUP Langue VCR Affi.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 31 Chapitre 4 FONCTIONNEMENT DU LECTEUR DVD Lecture d’un disque Avant la lecture - Allumez votre téléviseur et réglez-le sur la bonne entrée vidéo de votre télécommande. - Si vous avez connecté un système audio externe sur votre téléviseur, allumez ce système audio et réglez-le sur la bonne entrée audio. Lecture 1 Appuyez sur le bouton OPEN / CLOSE ( ) situé sur la façade. 2 Placez délicatement un disque dans le tiroir, côté étiquette vers le haut.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 32 DU LECTEUR DVD ▼ 5 Mise en pause de la lecture Appuyez sur le bouton (Marche/Pause) de votre télécommande ou de la façade de l’appareil pendant la lecture. - L’affichage se fige et le son est coupé. - Appuyez de nouveau sur le bouton (Marche/Pause) pour reprendre la lecture. Remarque Le lecteur s’arrête automatiquement s’il est laissé en mode pause durant 5 minutes.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 33 DU LECTEUR DVD Utilisation des fonctions Recherche et Saut Au cours de la lecture, vous pouvez faire une recherche rapide dans le chapitre ou la piste et utiliser la fonction saut pour aller à la sélection suivante. Recherche dans un chapitre ou une piste ▼ Si vous souhaitez effectuer une recherche plus rapide sur le DVD ou le VCD/CD, appuyez et maintenez le bouton enfoncé.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 34 DU LECTEUR DVD Utilisation de la fonction Affichage pendant la lecture d’un DVD/VCD/CD/MPEG4 Pendant la lecture d’un DVD/CD ▼ Vous pouvez sélectionner une information dans le menu Fonction du DVD en appuyant sur le bouton MENU. 1 Pendant la lecture, appuyez sur le bouton INFO. de la télécommande. 2 DVD Servez-vous des boutons "/# pour sélectionner l’élément souhaité. ENG ENG MOVE VCD/CD ▼ Lors de la lecture d’un VCD 2.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 35 DU LECTEUR DVD 4 Pour quitter le menu, appuyez une nouvelle fois sur le bouton INFO. Remarque TITLE CHAPTER Pour accéder au titre souhaité lorsque le disque en comporte plusieurs. Par exemple, si le DVD contient plusieurs films, chaque film est identifié. La plupart des DVD sont enregistrés en chapitres afin de vous permettre de localiser rapidement un passage spécifique (les pistes sur un CD audio par exemple).
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 36 DU LECTEUR DVD Utilisation du menu Disque et Titre(lecteur DVD/VCD) ▼ 1 Pendant la lecture d’un DVD, appuyez sur le bouton MENU de la télécommande. Appuyez sur les boutons #/" pour sélectionner Fonction, puis appuyez sur le bouton $ ou ENTER. Fonction SETUP Fonctions du DVD $ Fonctions du VCR $ DVD VCR Lors de la lecture d’un VCD 2.0, vous pouvez choisir Menu oui ou Menu Non á l’aide de la touche DISC MENU.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 37 DU LECTEUR DVD Utilisation du menu Fonction (lecteur DVD/VCD) ▼ Le bouton MENU peut être utilisé pour accéder, pendant la lecture, aux fonctions Information, Zoom , Signet et EZ View du lecteur DVD. ▼ 1 Vous pouvez également sélectionner directement ces fonctions à l’aide des boutons correspondants de la télécommande. - Info - MARK - REPEAT Pendant la lecture d’un DVD, appuyez sur le bouton MENU de la télécommande.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 38 DU LECTEUR DVD Lecture répétée Répétition de la piste, du chapitre, du titre actuel, d’une section choisie (A-B) ou de tout le disque. Pendant la lecture d’un DVD/VCD/CD 1 Pendant la lecture, appuyez sur le bouton REPEAT de la télécommande. L’écran de répétition s’affiche. Non Off Appuyez sur les boutons %/$pour sélectionner Chapitre, Titre ou A-B, puis appuyez sur le bouton ENTER.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 39 D UNon LECTEUR DVD Utilisation de la fonction répétition A-B Off 1 Pendant la lecture, appuyez sur le bouton REPEAT de la télécommande. L’écran de répétition s’affiche. Chapitre Non Non Track 2 Appuyez sur les boutons %/$ pour sélectionner A-.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 40 DU LECTEUR DVD Lecture lente répétée Cette fonction permet de répéter en vitesse lente des séquences comportant du sport, de la danse, un concert instrumental, etc. afin de les étudier avec plus d’attention. Pendant la lecture d’un DVD 1 Pendant la lecture, appuyez sur les boutons (Play/Pause).
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 41 DU LECTEUR DVD Réglage du format de l’image (Vue EZ) Réglez le format de l’image (longueur x largeur) du téléviseur afin que le lecteur DVD affiche les films au format convenant à votre téléviseur. Lecture en utilisant le format de l’image (lecteur DVD) ▼ La fonction EZ View n’est pas disponible lorsque la fonction Répétition A-B est activée. Appuyez sur le bouton EZ VIEW situé sur la façade.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 42 DU LECTEUR DVD Si vous utilisez un téléviseur 4:3 Pour les disques au format 4:3 Pour les disques au format 16/9 - FORMAT CLASSIQUE Affiche le contenu du titre du DVD au format 4:3 - 4:3 Letter Box Affiche le contenu du titre du DVD au format 16/9. Les barres noires apparaissent en haut et en bas de l‘écran. - AJUSTEMEN A’LECRAN Le haut et le bas de l’écran sont coupés et le plein écran apparaît.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 43 DU LECTEUR DVD Sélection de la langue audio Vous pouvez sélectionner rapidement et facilement la langue audio voulue grâce au bouton AUDIO. Utilisation du bouton AUDIO (DVD/VCD/CD/MPEG4) 1 Appuyez sur le bouton AUDIO pendant la lecture. La fonction audio change lorsque le bouton est actionné plusieurs fois. Les langues audio sont représentées par des abréviations.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 44 DU LECTEUR DVD Sélection de la langue des sous-titres Vous pouvez sélectionner rapidement et facilement le sous-titre voulu grâce au bouton SUBTITLE. Utilisation du bouton SUBTITLE (lecteur DVD/MPEG4) Remarques - Pour changer le sous-titre voulu dans le menu Disque, appuyez sur le bouton DISC MENU. - Cette fonction varie selon les sous-titres présents sur le disque et peut ne pas fonctionner avec tous les DVD.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 45 DU LECTEUR DVD Changement de l’angle de caméra Lorsqu’un DVD contient plusieurs angles pour une scène donnée, vous pouvez utiliser la fonction ANGLE. Utilisation du bouton ANGLE (lecteur DVD) Si le disque contient plusieurs angles, l'icône ANGLE ( ) apparaît à l'écran. 1 Appuyez sur le bouton ANGLE, l'icône ANGLE s'affichera alors avec le numéro de l'angle actuel et les numéros des angles disponibles.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 46 DU LECTEUR DVD Rappel d’une scène marquée 1 Appuyez sur le bouton MARK de la télécommande en cours de lecture. 2 Appuyez sur les boutons %&$ pour sélectionner une scène marquée. 3 Appuyez sur le bouton (Lecture/Pause) pour passer à la scène marquée. Suppression d’un repère 1 Appuyez sur le bouton MARK de la télécommande en cours de lecture. 2 Appuyez sur les boutons %&$ pour sélectionner le numéro du signet à supprimer.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 47 DU LECTEUR DVD Utilisation de la fonction Zoom (lecteur DVD) 1 Pendant la lecture d’un DVD, appuyez sur le bouton MENU de la télécommande. 2 Appuyez sur les boutons #/" pour sélectionner Fonction, puis appuyez sur le bouton $ ou ENTER. Fonction SETUP Fonctions du DVD $ Fonctions du VCR $ DVD VCR PROG FUNC ENTER 3 Appuyez sur les boutons #/" pour sélectionner Fonction du DVD, puis appuyez sur le bouton $ ou ENTER.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 48 DU LECTEUR DVD Séquences animées pour MP3/WMA/JPEG/MPEG4 Les disques MP3/WMA/JPEG/MPEG4 contiennent des chansons et/ou des images individuelles pouvant être organisées en dossiers, comme cela vous est représenté ci-dessous. Ils se gèrent de la même manière que lorsque vous utilisez votre ordinateur pour classer des fichiers dans différents dossiers. Non 1 Ouvrez le tiroir disque. 2 Placez le disque dans le tiroir. 3 Fermez le tiroir.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 49 DU LECTEUR DVD Lecture de disques MP3/WMA 1 Ouvrez le tiroir disque. Non O f f 00:00:23 2 1_mp3 B e c a u s e Yo u Cactus Placez le disque dans le tiroir. Sad Day Wonderful 3 Fermez le tiroir. ▼ 4 Appuyez sur les boutons #&" ou %&$ pour sélectionner un fichier musical. Appuyez sur le bouton ENTER pour commencer la lecture du fichier musical.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 50 DU LECTEUR DVD Fichier CD-R MP3/WMA - Utilisez un taux de transfert de décompression d’au moins 64 Kbps pour enregistrer des fichiers WMA. Lorsque vous enregistrez des fichiers MP3 ou WMA sur un CD-R, veuillez respecter les consignes suivantes. La qualité sonore des fichiers WMA dépend essentiellement du taux de compression/décompression que vous choisissez. - Vos fichiers MP3 ou WMA doivent être au format ISO 9660 ou JOLIET.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 51 DU LECTEUR DVD Lecture de MPEG4 Fonction lecture MPEG4 Les fichiers AVI utilisés contiennent les données audio et vidéo. Seuls les fichiers au format AVI dotés de l'extension “.avi” peuvent être lus. 1 Ouvrez le tiroir de disques. Placez le disque sur le plateau. Fermez le tiroir.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 52 DU LECTEUR DVD Description des fonctions disponibles pour les fichiers MPEG-4 Fonction Description Page de référence En cours de lecture, appuyez sur Sauter le touche ou pour ( ou ) avancer ou reculer de 5 minutes. Pendant la lecture, appuyez sur les touches de la télécommande SEARCH Recherche ( ou ) (Recherche ( ou ) avancée ou arrière). Vous permet d’effectuer une recherche rapide dans un fichier AVI.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 53 DU LECTEUR DVD Lecture de programme et lecture aléatoire Vous pouvez écouter des chansons en mode aléatoire ou dans la séquence souhaitée. Il est possible de programmer jusqu’à 20 plages. Cette fonction est disponible seulement avec des CD audio. Lecture de programme 1 Remarque Lecture aléatoire • Lorsque le lecteur est en mode Arrêt, appuyez sur le bouton REPEAT. - Le menu du mode lecture s'affiche.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 54 DU LECTEUR DVD Lecture d’un CD image 1 Non Sélectionnez le dossier souhaité puis appuyez sur le bouton ENTER. Non 2 Appuyez sur les boutons #&" pour sélectionner un fichier Image, puis appuyez sur le bouton ENTER. Remarques - Si vous n’appuyez sur aucun bouton de la télécommande durant 10 secondes, le menu disparaîtra. - Appuyez sur le bouton (Arrêt) pour revenir au menu des séquences animées.
00956G V5650 XAC_Fra2 01 14/3/06 FONCTIONNEMENT 10:32 Page 55 DU LECTEUR DVD Disques JPEG CD-R - Seuls les fichiers possédant une extension « .jpg » et « .JPG » peuvent être lus. - Si le disque n'est pas fermé, la lecture débute plus tardivement et vous ne pouvez pas lire l'ensemble de vos fichiers enregistrés. - Seuls les disques CD-R avec fichiers JPEG au format Joliet ou conformes à la norme ISO 9660 peuvent être lus.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 56 FONCTIONNEMENT DU LECTEUR DVD Utilisation du menu Configuration Grâce au menu Configuration, vous pouvez personnaliser votre lecteur DVD en sélectionnant différentes préférences relatives à la langue, en définissant un contrôle parental et même, en configurant votre lecteur en fonction du type d'écran de votre téléviseur. 1 Lorsque l'appareil est en mode Arrêt, appuyez sur le bouton MENU de la télécommande.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 57 FONCTIONNEMENT DU LECTEUR DVD Configuration des paramètres de langue Si vous réglez préalablement les options aucun menu de lecteur sur le menu disque avec affichage à l'écran, audio et langue des sous-titres, celles-ci sont activées automatiquement à chaque fois que vous visionnez un film. 1 Lorsque l'appareil est en mode Arrêt, appuyez sur le bouton MENU de la télécommande.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 58 FONCTIONNEMENT DU LECTEUR DVD Fonction Langue ▼ Menus du Disque Pour définir la langue du menu Disque, procédez comme suit. Si la langue que vous souhaitez est disponible sur un lecteur DVD, le menu Disque apparaît automatiquement dans la langue de votre choix.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 59 FONCTIONNEMENT DU LECTEUR DVD Configuration des options audio Les options audio vous permettent de régler le son de votre système audio externe. 1 Lorsque le lecteur DVD est en mode Arrêt, appuyez sur le bouton MENU de la télécommande. 2 . e. Appuyez sur les boutons #&" pour sélectionner DVD, puis appuyez sur le bouton $ ou ENTER.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 60 FONCTIONNEMENT DU LECTEUR DVD Options audio Sortie numérique - PCM : conversion en audio PCM(2CH). Options Audio Sortie Numérique DTS Compression Dynamique ECHANTILLONNAGE PCM : : : : PCM Non Oui Oui $ $ $ $ - Bitstream : son Dolby Digital par la sortie numérique. ENTER RETURN DTS Sélectionnez Activé lorsque vous connectez votre appareil à un décodeur DTS. - Non: Pas de sortie du signal numérique. - Oui: Flot binaire DTS par la sortie numérique.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 61 FONCTIONNEMENT DU LECTEUR DVD Configuration des options d’affichage Les options d'affichage vous permettent de configurer différentes fonctions vidéo du lecteur. 1 Lorsque l'appareil est en mode Arrêt, appuyez sur le bouton MENU de la télécommande. 2 Appuyez sur les boutons #&" pour sélectionner DVD, puis appuyez sur le bouton $ ou ENTER.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 62 FONCTIONNEMENT DU LECTEUR DVD Options d'affichage Format Ecran En fonction de votre type de téléviseur, il est possible que vous souhaitiez procéder à un réglage de l'écran (format de l'image) $ - Format “Boîte à lettres” 4:3 Permet d'afficher l'écran au format 16/9 proposé par le DVD et ce, même si vous possédez un téléviseur avec écran au format 4:3. Des barres noires apparaissent en haut et en bas de l'écran.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 63 FONCTIONNEMENT DU LECTEUR DVD Configuration du contrôle parental La fonction de contrôle parental peut être configurée si les DVD ont fait l'objet d'une évaluation vous permettant de contrôler le genre des DVD regardés par les membres de votre famille. Chaque disque comporte jusqu’à 8 niveaux d'évaluation. 1 Lorsque le lecteur DVD est en mode Arrêt, appuyez sur le bouton MENU de la télécommande.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 64 FONCTIONNEMENT DU LECTEUR DVD Configuration du niveau d'évaluation 1 Lorsque l'appareil est en mode Arrêt, appuyez sur le bouton MENU de la télécommande. 2 Appuyez sur les boutons #&" pour sélectionner DVD, puis appuyez sur le bouton $ ou ENTER. Réglage DVD SETUP Langue $ Audio $ DVD Affichage VCR $ Cont. Parental $ Inscription DivX(R) $ PROG FUNC ENTER 3 Appuyez sur les boutons #&" pour sélectionner Cont.
00956G V5650 XAC_Fra2 01 14/3/06 10:32 Page 65 FONCTIONNEMENT DU LECTEUR DVD Modification du mot de passe 1 Lorsque l'appareil est en mode Arrêt, appuyez sur le bouton MENU de la télécommande. 2 Appuyez sur les boutons #&" pour sélectionner DVD, puis appuyez sur le bouton $ ou ENTER. Réglage DVD SETUP Langue $ Audio $ DVD Affichage VCR $ Inscription DivX(R) $ PROG FUNC ENTER 3 Appuyez sur les boutons #&" pour sélectionner Cont. Parental, puis appuyez sur le bouton $ ou ENTER. $ Cont.
00956G V5650 XAC_Fra3 01 14/3/06 10:37 Page 66 Chapitre 5 FONCTIONNEMENT DU MAGNETOSCOPE Dans ce chapitre, vous apprendrez comment lire une cassette vidéo, comment utiliser le compteur de temps et les fonctions d'arrêt mémoire, et enfin comment enregistrer un programme télévisé en regardant la télévision.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 67 DU MAGNETOSCOPE Lecture d’une cassette vidéo préenregistrée Lecture de la cassette ▼ ▼ 1 - Pour plus d’informations concernant la languette de sécurité, reportezvous page 78. - Le magnétoscope n'émet aucun son lorsqu'une cassette vidéo est en pause. Insérez la cassette vidéo dans le logement prévu à cet effet. 2 Si la lecture de la cassette ne démarre pas automatiquement, appuyez sur le bouton (Lecture/Pause).
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 68 DU MAGNETOSCOPE Fonctions de lecture magnétoscope spéciales Lors de la lecture d'une cassette vidéo, vous pouvez accéder à différentes fonctions de lecture spéciales : Image figée, Avance image par image, Sauter, Répéter, etc. Appuyez de nouveau sur le bouton Lecture/Pause pour reprendre une lecture normale. Avance image par image En mode pause, appuyez sur le bouton F.ADV pour avancer jusqu'à la prochaine image.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 69 DU MAGNETOSCOPE Utilisation de l'alignement automatique Le réglage Alignement supprime les lignes blanches apparaissant parfois en cours de lecture en raison de légères différences existant dans les platines d'enregistrement. Pour résoudre ce problème, le bouton TRK aligne automatiquement les plages enregistrées avec les têtes de lecture. L'alignement peut également être effectué manuellement.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 70 DU MAGNETOSCOPE Sélection d’un type de cassette Si vous souhaitez utiliser le compteur de bande pour afficher le temps restant sur la cassette, vous devez indiquer le type de cassette insérée. 1 Appuyez sur le bouton MENU de la télécommande. 2 Appuyez sur les boutons "$# pour sélectionner Réglage VCR, puis appuyez sur le bouton %ou ENTER.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 71 DU MAGNETOSCOPE Réglage de la lecture automatique Si vous souhaitez que la lecture démarre automatiquement lorsque vous insérez une cassette vidéo dans le magnétoscope, activez l'option Lecture automatique. Remarque Au moment de l'insertion, la lecture automatique démarre uniquement pour les cassettes dont la languette de sécurité pour l'enregistrement a été retirée (voir page 65). 1 Appuyez sur le bouton MENU de la télécommande.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 72 DU MAGNETOSCOPE Réglage de la répétition automatique Si vous souhaitez que la lecture de vos cassettes vidéo se fasse de manière répétée, activez Répétition automatique. 1 Appuyez sur le bouton MENU de la télécommande. 2 Appuyez sur les boutons "$#! pour sélectionner Réglage VCR, puis appuyez sur le bouton % ou ENTER.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 73 DU MAGNETOSCOPE Utilisation du compteur de bande Le compteur de bande : - Indique le temps écoulé dans les modes lecture et enregistrement (heures, minutes et secondes). - Est remis à zéro lorsqu'une cassette est insérée dans le lecteur DVD-magnétoscope - Permet de trouver facilement le début d'une séquence. - Pour un calcul correct du temps restant, vous devez indiquer le type de cassette utilisée.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 74 DU MAGNETOSCOPE Utilisation de la fonction Assemble Edit Cette fonction vous permet de démarrer un nouvel enregistrement à un point spécifique de la cassette sans décrochage important entre les scènes. 1 Insérez la cassette à modifier dans le lecteur DVDmagnétoscope. 2 Appuyez sur le bouton (Lecture/Pause) pour démarrer la lecture.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 75 DU MAGNETOSCOPE 6 Sélectionnez la source depuis laquelle vous souhaitez enregistrer en appuyant sur : - Le bouton CH " ou #pour les chaînes de télévision. - Le bouton INPUT SEL. pour la source d’entrée LINE1 ou LINE2. 7 Appuyez sur le bouton REC pour démarrer l’enregistrement. Lorsque l’enregistrement est terminé, appuyez sur le bouton (Arrêt).
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 76 DU MAGNETOSCOPE Recherche d’une séquence spécifique Chaque fois que vous enregistrez une cassette sur le lecteur DVD-magnétoscope, un “index” se fixe automatiquement sur la cassette lorsque l’enregistrement démarre. La fonction Recherche vous permet d’avancer rapidement ou de rembobiner la cassette vers un index spécifique et de reprendre la lecture depuis ce point.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 77 DU MAGNETOSCOPE Système de recherche variable Aller à [0:00:00] Utilisez cette fonction lorsque vous souhaitez effectuer une recherche de la position 00:00:00 du compteur sur une cassette.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 78 DU MAGNETOSCOPE Enregistrement de base Vous pouvez enregistrer un programme télévisé en cours de diffusion en insérant une cassette vierge dans le magnétoscope et en appuyant sur le bouton REC. Vous pouvez même ajouter une durée d’enregistrement par incrément de 30 minutes jusqu’à 4 heures en appuyant sur le bouton REC de façon répétée (voir page 81).
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 79 DU MAGNETOSCOPE Remarque L’enregistrement depuis le lecteur DVD vers le magnétoscope n’est pas possible. 3 Appuyez sur le bouton REC de la télécommande ou de la façade. Concernant les options proposées en cours d’enregistrement, reportez-vous à la rubrique “Fonctions d’enregistrement particulières” sur cette page. 4 Pause / Reprise de l’enregistrement Appuyez sur le bouton (Lecture/Pause).
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 80 DU MAGNETOSCOPE Regarder un DVD lors d'un enregistrement Insérez un DVD dans le tiroir disque, puis appuyez sur le bouton (Lecture/Pause). La sortie passera automatiquement sur le DVD. Ajout d’une durée d'enregistrement Reportez-vous à Enregistrement immédiat (OTR) cidessous.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 81 DU MAGNETOSCOPE 4 En mode Enregistrement, appuyez à nouveau sur le bouton REC pour activer l'enregistrement immédiat (OTR). Durée d'enregistrement 0:30 apparaît sur l'affichage à l'écran et le lecteur DVD-magnétoscope enregistre pendant exactement 30 minutes.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 82 DU MAGNETOSCOPE Utilisation de l’enregistrement programmé Insérez une cassette vidéo vierge dans la fente du magnétoscope. Assurez-vous de laisser intacte la languette de sécurité pour l'enregistrement. Grâce à la fonction d'enregistrement programmé, vous pouvez programmer jusqu'à 7 événements à la fois pour un enregistrement un mois à l'avance.
00956G V5650 XAC_Fra3 01 14/3/06 FONCTIONNEMENT 10:37 Page 83 DU MAGNETOSCOPE Sélection de la vitesse automatique Si la durée de la cassette vidéo n'est pas suffisante pour un enregistrement programmé en mode Lecture standard SP, réglez la vitesse d'enregistrement sur “Auto”. L'enregistrement démarre en mode SP Lecture standard. Si la durée n'est pas suffisante, la vitesse de la cassette passera automatiquement du mode SP Lecture standard au mode SLP Lecture super longue.
00956G V5650 XAC_Fra3 01 14/3/06 10:37 Page 84 Chapitre 6 REFERENCE Dépannage Avant de contacter un centre de service agréé Samsung, effectuez les vérifications élémentaires suivantes. Si vous ne savez pas résoudre vous-même le problème après avoir lu les instructions ci-dessus, veuillez noter : - Le modèle et le numéro de série se trouvant à l'arrière de votre lecteur DVD-magnétoscope.
00956G V5650 XAC_Fra3 01 14/3/06 10:37 Page 85 REFERENCE Problème Action Page L'écran est bloqué • Appuyez sur le bouton / pendant plus de 5 secondes sans disque dans le lecteur. Tous les réglages se réinitialisent sur les réglages usine. - Mot de passe oublié • Pour un démarrage à froid sans disque dans le lecteur, appuyez simultanément pendant 5 secondes sur les boutons / de la façade. Tous les réglages, y compris le mot de passe, se réinitialisent sur les réglages usine.
00956G V5650 XAC_Fra3 01 14/3/06 10:37 Page 86 REFERENCE Caractéristiques techniques AUDIO Entrées 2 entrées stéréo audio, connecteur RCA,-8 dbm, 47 KΩ, avant et arrière VIDEO 2 entrées vidéo composites, connecteur RCA, 75 Ω, 1 Vp-p RF Antenne ou entrée CATV, connecteur F, 75 Ω AUDIO 1 sortie stéréo audio, connecteur RCA,-8 dbm, 1,5KΩ AUDIO (DVD uniquement) 1 sortie audio numérique (1 coaxial) 1 paire de sorties stéréo audio Sorties VIDEO VIDEO (DVD uniquement) 1 sortie vidéo composite, co
00956G V5650 XAC_Fra3 01 14/3/06 10:37 Page 87 Contactez SAMSUNG WORLD WIDE Si vous avez des commentaires our des questions concernant les produits Samsung, contactez le centre de service à la clientèle SAMSUNG. Region North America Latin America Europe CIS Country CANADA MEXICO U.S.A ARGENTINE BRAZIL CHILE COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP.
00956G V5650 XAC_Fra3 01 14/3/06 10:37 Page 88 GARANTIE LIMITÉE À L’ACHETEUR INITIAL Samsung Electronics Canada Inc. (SECA) garantit ce produit contre tout défaut de fabrication. SECA garantit aussi que si cet appareil ne fonctionne pas convenablement durant la période de garantie SECA se réservera le droit de réparer ou de remplacer l’appareil défectueux. Toutes les réparations sous garantie doivent être effectuées par un Centre de service autorisé SECA.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 1 Instruction Manual DVD-V5650 CA AK68-00956G.01 www.samsung.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 2 SAFETY INSTRUCTIONS Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 3 SAFETY INSTRUCTIONS Precautions TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury. This symbol indicates important instructions accompanying the product.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 4 SAFETY INSTRUCTIONS CAUTION THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. Note: • This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used elsewhere.
00956G V5650 XAC_Eng1*01 14/3/06 BEFORE 10:05 Page 5 Y O U S TA R T Before you start Accessories Remote Control (AK59-00051A) Batteries-2EA 1.5V(AAA) (AC43-12002H) Video/Audio Cable (AC39-00073A) Install Batteries in the Remote Control 1 Open the battery cover on the back of the remote control. 2 Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly. 3 Replace the battery cover.
00956G V5650 XAC_Eng1*01 14/3/06 TA B L E OF 10:05 Page 6 CONTENTS Table of Contents Safety Instructions ........................................................................................................................................2 Important Safety Instructions ................................................................................................................2 Precautions ..........................................................................................................
00956G V5650 XAC_Eng1*01 14/3/06 TA B L E OF 10:05 Page 7 CONTENTS Chapter 4: DVD Operations Playing a Disc ..............................................................................................................................................31 Using the Search and Skip Functions ........................................................................................................33 Using the Display Function ..................................................................................
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 8 Chapter 1 SETUP General Features DVD-VCR Features ■ ■ ■ ■ ■ ■ Perfect compatibility to play back DVDs, audio CDs, VCD or VHS Tapes. Enjoy a DVD movie while recording a TV show to the VCR. Auto Setup instantly finds the time and runs channel search. RF input and output. Composite, S-Video, and Component Video outputs. On-Screen Program (English/French/Spanish).
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 9 SETUP Disc Type and Characteristics This DVD-VCR is capable of playing the following types of discs with the corresponding logos: Disc Types (Logos) Recording Types Disc Size Max. Playing Time DVD Audio + Video VIDEO-CD Audio + Video AUDIO-CD 5” 3 1/2” Single-sided 240 min. - DVD contains excellent sound and video due to Dolby Digital Double-sided 480 min. and MPEG-2 system. Various screen and audio Single-sided 80 min.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 10 SETUP Description Front Panel Controls 1 4 1 2 3 4 5 6 7 8 9 2 5 6 8 7 DISC TRAY Place the disc here. VCR Deck Insert a standard VHS video tape. EJECT Press to eject a video tape if the tape is stopped. (POWER) Press to turn the DVD-VCR on and off. LINE IN 2 Connect to the Video/Audio output jack of your external device. P.SCAN Press to select video out mode. OPEN/CLOSE Press to open and close the disc tray.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 11 SETUP Rear Panel ❶ ❷ ❸ ❹ ➎ 1 2 3 4 ❻ ❼ AUDIO OUT Connect to the Audio input jacks of your television. You can use as audio output terminal when Component or S-Video is connected. COMPONENT VIDEO OUT - Use these jacks if you have a TV with Component Video in jacks. These jacks provide PR, PB and Y video. - If Component (Progressive Scan) Video Output is selected in the Alt Video Out menu or by using the P.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 12 SETUP Tour of the Remote Control 1 2 3 4 5 6 7 8 9 10 11 12 13 POWER button Press to turn the DVD-VCR on and off. NUMBER Buttons AUDIO button Use this button to access various audio functions on a disc. (DVD) Skip button Press to reverse skip a disc. Use to skip a title, chapter or track on a disc. REC button Press to begin recording. (VCR) Search button Press to reverse search a disc.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 13 Chapter 2 CONNECTIONS Connecting the Antenna Cable There are several ways to connect your DVD-VCR. Select one of the following antenna connections that best suits you below.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 14 CONNECTIONS Method2: Antenna + DVD-VCR + TV: Cable box with many scrambled channels Wall You can record channels by selecting the channel on the cable box. You cannot record one channel while watching another channel. Be sure that the cable box is turned on.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 15 CONNECTIONS Before Connecting the DVD-VCR - Always turn off the DVD-VCR, TV, and other components before you connect or disconnect any cables. - Refer to the user’s manual of the additional components (such as a TV) you are connecting for more information on those particular components. Connection to a TV The following shows examples of connections commonly used to connect the DVD-VCR with a TV and other components.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 16 CONNECTIONS Connection to a TV (S-Video) - Connecting to your TV using an S-Video cable. - You will enjoy high quality images. S-Video separates the picture element into black and white(Y) and color(C) signals to present clearer images than regular video input mode. (Audio signals are delivered through the audio out or line out audio).
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 17 CONNECTIONS Connection to a TV (Interlace) - Connecting to your TV using Component video cables. - You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio signals are delivered through the audio out or line out audio).
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 18 CONNECTIONS Connection to a TV (Progressive) 1 Using component video cables (not included), connect the COMPONENT VIDEO OUT terminal on the rear of the DVD-VCR to the COMPONENT IN terminal of your TV. 2 Using the audio cables, connect from the AUDIO OUT or LINE OUT AUDIO (red and white) terminals on the rear of the DVD-VCR to the AUDIO (red and white) IN terminals of your TV. Blue Red White Turn on the DVD-VCR and TV.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 19 CONNECTIONS Connection to an Audio System Connection to an Audio System (2 Channel Amplifier) 1 Using the audio cables, connect the (LINE) AUDIO (red and white) OUT terminals on the rear of the DVD-VCR to the AUDIO (red and white) IN terminals of the Amplifier.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 20 CONNECTIONS Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier) 1 Using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD-VCR to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier. 2 Using the video signal cable(s), connect the S-VIDEO or COMPONENT OUT terminals on the rear of the DVD-VCR to the S-VIDEO or COMPONENT IN terminal of your TV as described on pages 15 to 18.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 21 CONNECTIONS Connecting a Power Cord & Auto Setup 1 Your DVD-VCR's power cord should be plugged into a standard 120V/60Hz wall outlet. Avoid pressing any buttons on the remote control or on the unit during Auto Setup. While your DVD-VCR is running Auto Setup, “Auto” will blink. When Auto Setup is complete, the current time will be displayed on the front panel. If Auto Setup fails to locate a channel to set the clock, you should set the clock manually.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 22 Chapter 3 INITIAL SETUP Selecting a Menu Language To change the on-screen MENU language to English, French or Spanish, follow these steps. 1 Press the MENU button. 2 Press the " buttons to select Setup, then press the % or ENTER button. 3 Press the " buttons to select Language, then press the % or ENTER button. 4 Press the " buttons to select the appropriate language : English, Français or Español. Press the ENTER button.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 23 INITIAL SETUP Setting the Clock This menu is used to set the current time. You need to set the time to use timer recording. Setting the Clock Automatically 1 Press the MENU button. 2 Press the " buttons to select Setup, then press the % or ENTER button. 3 Press the " buttons to select Clock, then press the % or ENTER button. Notes You must have the antenna connected to set the Auto Clock.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 24 INITIAL SETUP 6 Press the " buttons to select Time Zone, then press the % or ENTER button. Select the time zone of your area by using the ",$&% buttons, then press the ENTER button. Select Automatic to set the time zone automatically. 7 Press the " buttons to select Daylight Saving, then press the % or ENTER button to select Yes, No or Auto. 8 Press the MENU button to exit.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 25 INITIAL SETUP 2 Press the " buttons to select Setup, then press the % or ENTER button. 3 Press the " buttons to select Clock, then press the % or ENTER button. 4 Press the " buttons to select Manual Clock, then press the % or ENTER button. 5 Use the $&% buttons to select each of the following options, then use the " buttons to set each option. Press the ENTER button to set the clock.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 26 INITIAL SETUP Memorizing the Channels Selecting the Video Signal-source This feature allows you to manually set the DVD-VCR’s tuner band to Antenna or Cable, whichever you connected to the Antenna In jack during initial setup. Use this setting only if Auto Setup detected the incorrect tuner band, i.e. channels are coming in on the wrong channel numbers. 1 Press the MENU button. 2 Press the " buttons to select Setup, then press the % or ENTER button.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 27 INITIAL SETUP Storing Channels in Memory (Automatic Method) Auto Channel Memory will automatically seek and store all active channels in your area. 5 Press the " buttons to select Auto Channel Memory, then press the % or ENTER button. The DVD-VCR will automatically search for all available channels in the selected tuner band. This procedure may take a few minutes to complete.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 28 INITIAL SETUP Selecting the RF Output Channel Use this feature if the DVD-VCR is connected to your TV using the RF antenna cable. 1 Press the MENU button. 2 Press the " buttons to select Setup, then press the % or ENTER button. 3 Press the " buttons to select Channel, then press the % or ENTER button. 4 Press the " buttons to select RF Output CH, then press the % or ENTER button to select 3CH or 4CH. 5 Press the MENU button to exit.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 29 INITIAL SETUP Selecting the Front Panel Display You can set the Front Panel Display to be bright all the time, dim all the time, or to automatically dim during power off. 1 Press the MENU button. 2 Press the " buttons to select Setup, then press the % or ENTER button. 3 Press the " buttons to select Front Display, then press the % or ENTER button to select Auto, Bright or Dim. 4 Press the MENU button to exit.
00956G V5650 XAC_Eng1*01 14/3/06 10:05 Page 30 INITIAL SETUP Setting the Power Off Automatically This feature automatically turns off your DVD-VCR if no signal is received and you do not press any buttons for the selected time. 1 Press the MENU button. 2 Press the " buttons to select Setup, then press the % or ENTER button. 3 Press the " buttons to select Auto Power Off, then press the % or ENTER button to select Off, 1Hr or 2Hr. 4 Press the MENU button to exit.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 31 Chapter 4 D V D O P E R AT I O N S Playing a Disc Before Play - Turn on your TV and set it to the correct Video Input on your TV's remote control. - If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input. Playback 1 Press the OPEN/CLOSE ( button on the front panel. ) 2 Place a disc gently into the tray with the disc’s label facing up.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 32 D V D O P E R AT I O N S ▼ 5 Pausing Play Press the (Play/Pause) button on your remote control or on the front panel during play. Note If the player is left for about 5 minutes in pause mode, it will stop. ▼ - Each time the button is pressed, a new frame will appear. - No sound is heard during STEP mode. - Press the (Play/Pause) button to resume normal play. - You can only perform step motion play in the forward direction.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 33 D V D O P E R AT I O N S Using the Search and Skip Functions During play, you can search quickly through a chapter or track, and use the skip function to jump to the next selection. Searching through a Chapter or Track ▼ If you want to search at a faster speed on the DVD, VCD or CD, press the button. During play, press the / (Search) buttons on the remote control.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 34 D V D O P E R AT I O N S Using the Display Function When Playing a DVD/VCD/CD/MPEG4 ▼ You can select information in the DVD Function menu by pressing the MENU button. 1 During play, press the INFO button on the remote control. 2 DVD Press the "#$ buttons to select the desired item. ENG ENG MOVE VCD/CD ▼ When VCD 2.0 is in Menu Off mode only,this function works. Select Menu Off by pressing the DISC MENU button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 35 D V D O P E R AT I O N S 4 To exit the menu, press the INFO button again. Note TITLE CHAPTER To access the desired title when there is more than one in the disc. For example, if there is more than one movie on a DVD, each movie will be identified. Most DVD discs are recorded in chapters so that you can quickly find a specific passage (similar to tracks on an audio CD). TRACK TIME AUDIO SUBTITLE Allows playback of the film from a desired time.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 36 D V D O P E R AT I O N S Using the Disc and Title Menu (DVD/VCD) ▼ 1 During playback of a DVD disc, press the MENU button on the remote control. MENU button can be used to access Disc and title menus on a DVD during playback. When VCD 2.0 is in Menu Off mode only,this function works. Select Menu Off by pressing the DISC MENU button. 2 Press the "#$ buttons to select Function, then press the % or ENTER button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 37 D V D O P E R AT I O N S Using the Function Menu (DVD/VCD) ▼ MENU button can be used to access DVD functions such as Information, Zoom, Bookmark, Repeat and EZ view menu during DVD playback. ▼ 1 You can also directly select these functions using their respective buttons on the remote control. - INFO - MARK - REPEAT During the playback of a DVD disc, press the MENU button on the remote control.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 38 D V D O P E R AT I O N S Repeat Play Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc. When playing a DVD/VCD/CD 1 During play, press the REPEAT button on the remote control. Repeat screen appears. Off Off ▼ 2 DVD Off Chapter Title A - B Press the % buttons to select Chapter, Title or A-B, then press the ENTER button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 39 D V D O P E R ATOffI O N S Using the A-B Repeat function Off 1 During play, press the REPEAT button on the remote control. Repeat screen appears. Chapter Off Off 2 Press the % buttons to select A-. Track DVD Off Off Chapter Title A - B Off Chapter VCD/CD Off Chapter Track Disc A - B Track B 3 DVD Track Off Chapter Title A - B Mark the Starting Point Press the ENTER button at ABthe beginning of the segment you want to repeat (Point A).
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 40 D V D O P E R AT I O N S Slow Repeat Play This feature allows you to slowly to repeat scenes containing sports, dancing, musical instruments being played etc., so you can study them more closely. When playing a DVD 1 During play, press the (Play/Pause) button. Off Off Continuous Slow Mode 2 Chapter 3 Press the REPEAT button on the remote control. Press the % buttons to select A-.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 41 D V D O P E R AT I O N S Adjusting the Aspect Ratio (EZ View) Set the aspect ratio (length x width) of your TV screen so the DVD-VCR will display movies at the appropriate size for your television. To Playback using Aspect Ratio (DVD) ▼ The EZ View feature is not available when the A-B Repeat function is activated. Press the EZ VIEW button on the front panel. - The screen size changes when the button is pressed repeatedly.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 42 D V D O P E R AT I O N S If you are using a 4:3 TV For 16:9 aspect ratio discs - 4:3 Letter Box Displays the content of the DVD title in 16:9 aspect ratio. The black bars will appear at the top and bottom of the screen. - 4:3 Pan Scan The left and right portions of the screen are cut off and the central portion of the 16:9 screen is displayed. - SCREEN FIT The top and bottom portions of the screen are cut off and a full screen appears.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 43 D V D O P E R AT I O N S Selecting the Audio Language You can select a desired audio language quickly and easily with the AUDIO button. Using the AUDIO button (DVD/VCD/CD/MPEG4) Notes - To change the desired audio in the Disc Menu, press the DISC MENU button. - This function depends on what audio languages are encoded on the disc and may not work on all DVDs. - A DVD disc can contain up to 8 audio languages.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 44 D V D O P E R AT I O N S Selecting the Subtitle Language You can select a desired subtitle quickly and easily with the SUBTITLE button. Using the SUBTITLE button (DVD/MPEG4) Notes - To change the desired subtitle in the Disc Menu, press the DISC MENU button. - This function depends on what subtitles are encoded on the disc and may not work on all DVDs. - A DVD disc can contain up to 32 subtitle languages.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 45 D V D O P E R AT I O N S Changing the Camera Angle When a DVD contains multiple angles of a particular scene, you can use the ANGLE function. Using the ANGLE button (DVD) If the disc contains multiple angles, the ANGLE appears on the screen. 1 Press the ANGLE button, then the ANGLE icon will appear with the current angle number and the number of angles available. Note If the disc has only one angle, this feature won’t work.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 46 D V D O P E R AT I O N S Recalling a Marked Scene 1 During play, press the MARK button on the remote control. 2 Press the % buttons to select a marked scene. 3 Press the (Play/Pause) button to play the marked scene. Clearing a Bookmark 1 During play, press the MARK button on the remote control. 2 Press the % buttons to select the bookmark number you want to delete. 3 Press the CLEAR button to delete a bookmark number.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 47 D V D O P E R AT I O N S Using the Zoom Function (DVD/VCD) 1 During the playback of a DVD disc, press the MENU button on the remote control. 2 Press the "#$ buttons to select Function, then press the % or ENTER button. 3 Press the "#$ buttons to select DVD Function, then press the % or ENTER button. 4 Press the "#$ buttons to select Zoom, then press the % or ENTER button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 48 D V D O P E R AT I O N S Clips Menu for MP3/WMA/JPEG/MPEG4 Discs with MP3/WMA/JPEG/MPEG4 contain individual songs and/or pictures that can be organized into folders as shown below. They are similar to how you use your computer to put files into different folders. 1 Open the disc tray. 2 Place the disc on the tray. 3 Close the tray. The tray closes and this screen displays.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 49 D V D O P E R AT I O N S MP3/WMA Playback 1 Open the disc tray. Off 00:00:23 2 1_mp3 B e c a u s e Yo u Cactus Place the disc on the tray. Sad Day Wonderful 3 Close the tray. ▼ 4 Press the "#$ or % buttons to select a song file. Off 00:00:23 Press the ENTER button to begin playback of the song file. 1_mp3 B e c a u s e Yo u Cactus Sad Day Wonderful Repeat/Random playback During play, press the REPEAT button to change the playback mode.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 50 D V D O P E R AT I O N S CD-R MP3/WMA file - Use a decompression transfer rate of at least 64Kbps when recording WMA files. When you record MP3 or WMA files on CD-R, please refer to the following. Sound quality with WMA files basically depends on the rate of compression/decompression you choose. - Your MP3 or WMA files should be ISO 9660 or JOLIET format.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 51 D V D O P E R AT I O N S MPEG4 Playback MPEG4 Play Function AVI files are used to contain the audio and video data. Only AVI format files with the “.avi” extensions can be played. 1 Open the disc tray. Place the disc on the tray. Close the tray. 2 $ or % Press the "#$ buttons to select an avi file (DivX/XviD), then press the ENTER button. Repeat Playback 1 Press the REPEAT button to change playback mode.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 52 D V D O P E R AT I O N S MPEG4 Function Description Function Description During play, press the or button, it moves forward or backward 5 minutes. During play, press the SEARCH ( or ) button and press Search again to search at a faster ( or ) speed. Allows you to search at a faster speed in an AVI file. (2X, 4X, 8X) Allows you to search at a Slow Motion slower speed in an AVI file.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 53 D V D O P E R AT I O N S Program Play & Random Play You can listen to songs randomly or in the desired sequence. Up to 20 tracks can be programmed. This function is available only with Audio CDs. Program Play Note Random Play • With the unit in stop mode, press the REPEAT button. - The play mode menu will appear. 1 With the unit in stop mode, press the REPEAT button. - The play mode menu will appear.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 54 D V D O P E R AT I O N S Picture CD Playback 1 Select the desired folder then press the ENTER button. 2 Press the "#$ buttons to select a Picture file in the clips menu, then press the ENTER button. Notes - If no buttons on the remote control are pressed for 10 seconds, the menu will disappear. - Press the (Stop) button to return to the clips menu. - When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 55 D V D O P E R AT I O N S CD-R JPEG Discs - Only files with the “.jpg” and “.JPG” extensions can be played. - If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played. - Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played. - The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special characters (. / = +).
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 56 D V D O P E R AT I O N S Using the Setup Menu The Setup menu lets you customize your DVD-VCR by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have. 1 With the unit in Stop mode, press the MENU button on the remote control. 2 Press the "#$ buttons to select DVD, then press the % or ENTER button. DivX(R) Registration % Œ Language: Setup of the Language.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 57 D V D O P E R AT I O N S Setting Up the Language Features If you set the player menu on the OSD disc menu, audio and subtitle language in advance, they will come up automatically every time you watch a movie. 1 With the unit in Stop mode, press the MENU button on the remote control. 2 Press the "#$ buttons to select DVD, then press the % or ENTER button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 58 D V D O P E R AT I O N S Language Function ▼ Disc Menu To set the Disc Menu Language to your preferred language, follow these steps. If your preferred language is available on a DVD, your Disc Menu Language will automatically be set to the language you choose. - If the selected language is not recorded on the disc, the original prerecorded language is selected. ▼ Audio To set the Audio Language to your preferred language, follow these steps.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 59 D V D O P E R AT I O N S Setting Up the Audio Options Audio Options allows you to set up sound for use with your external audio system. - 1 With the DVD in Stop mode, press the MENU button on the remote control. 2 Press the "#$ buttons to select DVD, then press the % or ENTER button. DivX(R) Registration % DivX(R) Registration % - 3 Press the "#$ buttons to select Audio, then press the % or ENTER button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 60 D V D O P E R AT I O N S Audio Options Digital Output - PCM: Converts to PCM(2CH) audio. PCM Down Sampling : On - Bitstream: Outputs Dolby Digital via the digital output. Select Bitstream when connecting to a Dolby Digital Decoder. Note There is no analog audio output when you play a DTS sound disc. DTS Select On when connecting to a DTS Decoder. Manufactured under license from Dolby Laboratories.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 61 D V D O P E R AT I O N S Setting Up the Display Options Display options enable you to set various video functions of the player. 1 With the unit in Stop mode, press the MENU button on the remote control. 2 Press the "#$ buttons to select DVD, then press the % or ENTER button. DivX(R) Registration % DivX(R) Registration % 3 Press the "#$ buttons to select Display, then press the % or ENTER button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 62 D V D O P E R AT I O N S Display Options TV Aspect Depending on the type of television you have, you may want to adjust the screen setting (aspect ratio). - 4:3 Letter Box: Select when you want to see the total 16:9 ratio screen the DVD supplies, even though you have a TV with a 4:3 ratio screen. Black bars will appear at the top and bottom of the screen.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 63 D V D O P E R AT I O N S Setting Up the Parental Control The Parental Control function works in conjunction with DVDs that have been assigned a rating, which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc. 1 With the DVD in Stop mode, press the MENU button on the remote control. 2 Press the "#$ buttons to select DVD, then press the % or ENTER button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 64 D V D O P E R AT I O N S Setting Up the Rating Level 1 With the unit in stop mode, press the MENU button on the remote control. 2 Press the "#$ buttons to select DVD, then press the % or ENTER button. % DivX(R) Registration 3 Press the "#$ buttons to select Parental, then press the % or ENTER button. Enter your password. 0~9 4 Press the "#$ buttons to select Rating Level, then press the % or ENTER button.
00956G V5650 XAC_Eng2 01 14/3/06 10:14 Page 65 D V D O P E R AT I O N S Changing the Password 1 With the unit in stop mode, press the MENU button on the remote control. 2 Press the "#$ buttons to select DVD, then press the % or ENTER button. % DivX(R) Registration 3 Press the "#$ buttons to select Parental, then press the % or ENTER button. Enter your password. 0~9 4 Yes Press the "#$ buttons to select Change Password, then press the % or ENTER button.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 66 Chapter 5 V C R O P E R AT I O N S In this chapter, you will learn how to play a video cassette tape, how to use the time counter and memory stop features, and how to record a program as you are watching TV. Inserting and Ejecting a Video Cassette Tape To Insert a Video Cassette Tape ▼ 1 Hold the video cassette tape window-side up with the arrow pointing away from you. - Don’t try to insert a tape upside down or backwards.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 67 V C R O P E R AT I O N S Playing a Pre-Recorded Video Cassette Tape Playing the Tape ▼ ▼ 1 - For more information on the safety tab, see page 78. - The VCR does not play sound while a video tape is paused. Insert the video cassette tape. 2 If the tape doesn’t begin to play automatically, press the (Play/Pause) button. 3 Pausing Play - See “Using Automatic Tracking” on the next page.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 68 V C R O P E R AT I O N S Special VCR Playback Features While a videotape is playing, you can enjoy a variety of special playback features, including Still, Frame Advance, Skip, Repeat, and more. Press the Play/Pause button again to resume normal playback. Frame Advance In the pause mode, press F.ADV to advance to the next frame.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 69 V C R O P E R AT I O N S Using Automatic Tracking The Tracking adjustment removes the white lines that sometimes appear during playback because of slight differences in recording decks. The TRK button will automatically align the recorded tracks with the playback heads to solve this problem. You may also set tracking manually. 1 Insert and play a video cassette tape. As soon as the tape begins to play, the VCR begins automatic tracking.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 70 V C R O P E R AT I O N S Selecting the Cassette Type If you wish to use the tape counter to display the time remaining on a cassette, you must indicate the type of cassette inserted. 1 Press the MENU button on the remote control. 2 Press the "$# buttons to select VCR, then press the % or ENTER button. n 3 Press the "$# buttons to select Tape Length, then press the % or ENTER button to select the correct cassette length.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 71 V C R O P E R AT I O N S Setting the Auto Play e If you want your videotapes to play automatically when you insert them, turn on Auto Play. Note Only tapes that are missing the Record Safety Tab will play automatically when inserted (See page 66). 1 Press the MENU button on the remote control. 2 Press the "$# buttons to select VCR, then press the % or ENTER button.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 72 V C R O P E R AT I O N S Setting the Auto Repeat If you want your videotapes to play repeatedly, turn on Auto Repeat. 1 Press the MENU button on the remote control. 2 Press the "$# buttons to select VCR, then press the % or ENTER button. n ▼ 3 Press the "$# buttons to select Auto Repeat, then press the % or ENTER button to select On or Off.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 73 V C R O P E R AT I O N S Using the Tape Counter The tape counter: - Indicates the elapsed time in the play and record modes (hours, minutes and seconds). - Is reset when a cassette is inserted in the DVD-VCR. - Allows you to easily find the beginning of a sequence. - If the remaining time is to be calculated correctly, you must indicate the type of cassette being used. 1 Insert a cassette in your DVDVCR.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 74 V C R O P E R AT I O N S Using the Assemble Edit Function This function allows you to start a new recording at a specific position on the cassette while maintaining a very smooth scene change. 1 Insert the cassette to be edited in your DVD-VCR. 2 Press the (Play/Pause) button to start playback. 3 When you reach the position from which you wish to start the new recording, press the (Play/Pause) button. 4 Press the F.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 75 V C R O P E R AT I O N S 6 Select the source from which you wish to record by pressing: - The CH " or # button for television channel. - The INPUT SEL. button for the LINE1 or LINE2 input source. 7 Press the REC button to start recording. When you have finished recording, press the (Stop) button. Selecting the Audio Output Mode You can select the mode in which the sound is reproduced on the loudspeakers and AV outputs.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 76 V C R O P E R AT I O N S Searching for a Specific Sequence Each time you record a cassette on this DVD-VCR, an “index” is automatically marked on the tape when recording starts. The Search function allows you to fast-forward or rewind to a specific index and start playback from that point. Depending on the direction selected, the indexes are numbered as follows: ➔ Prev Seq. etc. 2 Next Seq. Seq. being played 1 1 etc.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 77 V C R O P E R AT I O N S Variable Search System Go To [0:00:00] Stop Use this feature when you want to search for the 0:00:00 counter position on a cassette. Press the CLEAR button at the point on the tape where you want to set the counter to [0:00:00]. The VCR will rewind or fast forward, searching for the 0:00:00 counter position, and then automatically stop at that position.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 78 V C R O P E R AT I O N S Basic Recording You can record a TV show in progress by inserting a blank tape and pressing the REC button. You can even add time in 30-minute increments up to 4 hours by pressing the REC button repeatedly; see page 81. Note Be sure your videotape has a Record Safety Tab. If the tab is missing, you can cover the opening with a small piece of tape.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 79 V C R O P E R AT I O N S Note Recording from the DVD to the VCR is not possible. 3 Press the REC button on the remote control or front panel. For options while recording is in progress, see “Special Recording Features” on this page. 4 Pause/Resume Recording Press the (Play/Pause) button. Press the REC button again to resume. 5 Stop Recording Press the (Stop) button.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 80 V C R O P E R AT I O N S To Watch a DVD while Recording Insert a DVD in the DVD tray and press the (Play/Pause). The output will automatically change to the DVD. To Add Recording Time See One-Touch Recording (OTR) below. Using One-Touch Recording One-Touch Recording (OTR) allows you to add recording time in 30-minute increments up to 4 hours at the touch of a button. 1 Insert a blank VHS tape into the VCR deck.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 81 V C R O P E R AT I O N S 4 While in Record mode, press the REC button again to activate One-Touch Recording (OTR). Record length 0:30 appears on the On-screen display and the DVD-VCR will record for exactly 30 minutes. 5 Record length 0:30 07 Add Recording Time Continue pressing REC button to add recording time in 30 minute increments up to 4 hours. The DVD-VCR stops recording automatically when the time has elapsed.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 82 V C R O P E R AT I O N S Making a Timer Recording Insert a blank videotape into the VCR deck. Be sure to leave the Record Safety Tab intact. With the Timer Recording function, you can program up to 7 events at a time to record up to a month in advance. To Begin Setting the Timer Recording, - Power On your DVD-VCR. - Power On your TV. 1 Press the MENU button on the remote control. 2 Press the "$# buttons to select PROG, then press the % or ENTER button.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 83 V C R O P E R AT I O N S Selecting Auto Speed If the length of the videotape is not long enough for a timer recording in the SP mode, set the recording tape speed to “Auto”. Recording will start in the SP mode. If the length is not long enough, the tape speed will automatically change from SP mode to SLP mode. Daily/Weekly Date Programming Weekly [Sun~Sat]: Use this to record TV programs on the same channel at the same time every week.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 84 Chapter 6 REFERENCE Troubleshooting Before contacting a Samsung authorized service center, perform the following simple checks. If you are unable to solve the problem after reading the above instructions, note: - The model and serial number on the rear of your DVD-VCR - The warranty information - A clear description of the problem Then contact your nearest SAMSUNG service center.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 85 REFERENCE Problem The screen is blocked Forgot password Action • Press the / button for more than 5 seconds with no disc in the unit. All settings will revert to the factory settings. • From a cold start with no disc in unit, press the / button simultaneously on the front panel for 5 seconds. All settings including the password will revert to the factory settings. Don't use this unless absolutely necessary. If you experience other problems.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 86 REFERENCE Technical Specifications AUDIO Inputs 2 Stereo audio inputs, RCA Connector, -8dbm, 47KΩ, front and rear VIDEO 2 Composite video inputs, RCA Connector, 75Ω, 1Vp-p RF Antenna or CATV Input, F-Connector, 75Ω AUDIO 1 Stereo audio outputs, RCA Connector, -8dbm, 1.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 87 Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. Region North America Latin America Europe CIS Country CANADA MEXICO U.S.A ARGENTINE BRAZIL CHILE COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP.
00956G V5650 XAC_Eng3* 01 14/3/06 10:10 Page 88 LIMITED WARRANTY TO ORIGINAL PURCHASER Samsung Electronics Canada Inc.(SECA), warrants that this product is free from defective material and workmanship. SECA further warrants that if this product falls to operate properly within the specified warranty period and the failure is due to improper workmanship or defective materials, SECA will repair or replace the product at its option.