Dryer User manual DVE(G)50A8800*/DVE(G)50A8600* Untitled-1 1 2020-12-15 2:46:33
Contents English Safety information 4 What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING Important safety precautions Warnings Cautions 4 4 5 6 8 8 Regulatory notice 10 FCC Notice IC Notice Open Source Announcement 10 11 12 Installation requirements 13 Key installation requirements Location considerations Ducting requirements Exhausting requirements Gas requirements Electrical requirements 13 13 18 19 20 21 Installation 23 What’s inc
9 Control panel Operating a cycle Cycle overview Options System functions Special features Cycle chart Drying guide 39 41 42 44 47 49 51 53 Maintenance 54 Cleaning 54 Troubleshooting 55 Checkpoints Information codes 55 57 Specifications 59 Fabric care chart Protecting the environment Specification sheet 59 60 60 English Untitled-1 3 2020-12-15 English Operations 3 2:46:33
Safety information English Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features. What you need to know about the safety instructions Please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance.
English WARNING - Risk of Fire • Clothes dryer installation must be performed by a qualified installer. • Install the clothes dryer according to the manufacturer’s instructions and local codes. • Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
Safety information Important safety precautions English WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3.
English 18. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children. 19. Do not insert your hand under the dryer. -- This may result in injury. 20. Take care that children’s fingers are not caught in the door when closing it. -- This may result in injury. 21. The control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing.
Safety information English WARNING - What to do if you smell gas: • • • • • • Do not try to light any appliance. Do not turn on the appliance. Do not touch any electrical switch. Do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department.
English • Do not use fabric softeners or products to eliminate static unless the softener or product is recommended for dryer use by the manufacturer of the fabric softener or product. • Clean the lint screen before or after each load. • Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt. • The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. • This appliance must be properly grounded.
Regulatory notice FCC Notice English CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received including interference that cause undesired operation.
English Unintentional emitter per FCC Part 15 Product type : Clothes Dryers Model : DVE(G)50A8800*/DVE(G)50A8600* Responsible Party – U.S. Contact Information Samsung Electronics America, Inc. QA Lab America 19 Chapin Rd. Building D Pine Brook NJ 07058 Tel: 1-973-808-6375 Fax: 1-973-808-63 IC Notice The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: 1.
Regulatory notice Open Source Announcement English The software included in this product contains open source software. You may obtain the complete corresponding source code for a period of three years after the last shipment of this product by sending an email to mailto:oss.request@samsung.com. It is also possible to obtain the complete corresponding source code in a physical medium such as a CDROM; a minimal charge will be required. The following URL http://opensource.samsung.
Installation requirements Read through the following instructions before installing the dryer and keep this manual for future reference. English WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. Key installation requirements • • • • A grounded electrical outlet.
Installation requirements Dimensions English A U 9 Type Dimensions (in. (mm)) 14 Untitled-1 14 Front loading dryer A. Overall height 38.7 (984) B. Width 27.0 (686) C. Depth with door open 52.6 (1335) D. Depth 31.
Clearance requirement English This clearance requirement is applicable for dryers only. NOTE • For washer's clearance requirement, see the washer's user manual. • If the washer and dryer have different clearance requirements, use the one with the larger value. Alcove or closet installations WARNING • The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or closet. • No other fuel-burning appliance should be installed in the same closet as the dryer.
Installation requirements Undercounter installation English A 39.6 in. (1006 mm) B 1 in. (25 mm) C 1 in. (25 mm) A 5.9 in. (150 mm) B 6 in. (152 mm) C 52.0 in.
This clearance requirement is applicable for washer and dryer pair installation. 9 A 1 in. (25 mm) B 5.9 in. (150 mm) C 7.1 in. (180 mm) D 6 in. (152 mm) E 78.5 in. (1994 mm) English Side by side installation NOTE 9 U Stacking (MODEL NO: SKK-8K) Many of Samsung's washers and dryers can be stacked to maximize usable space. You can purchase an optional stacking kit from your Samsung retailer.
Installation requirements Ducting requirements English Recommended Use only for short-run installation 4” (10.2 cm) 2.5” (6.4 cm) Weather hood type No. of 90° elbows Rigid Rigid 0 80 ft. (24.4 m) 74 ft. (22.6 m) 1 68 ft. (20.7 m) 62 ft. (18.9 m) 2 57 ft. (17.4 m) 51 ft. (15.5 m) 3 47 ft. (14.3 m) 41 ft. (12.5 m) NOTE * Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.
Exhausting requirements English The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. In the United States and Canada • All dryers must be exhausted to the outside. • The required exhaust duct is 4 inches (10.2 cm) in diameter.
Installation requirements Gas requirements English WARNING • Use only natural or LP (liquid propane) gases. • The installation must be conformed with local codes, or in the absence of local codes, with the national fuel gas code, ANSI Z223.1/NFPA 54, latest revision(for the UNITED STATES), or with the natural gas and propane installation code, CSA B149.1(for Canada). • Gas dryers are equipped with a burner vent for use with natural gas.
Electrical requirements English The wiring diagram is located on the plate under the control panel or rear frame. WARNING • Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
Installation requirements Electrical connections English Before operating or testing, follow all grounding instructions in the “Grounding” section. An individual branch (or separate) circuit serving only your dryer is recommended. Do not use an extension cord. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service.
Installation This dryer must be installed by a qualified technician. The installer is responsible for connecting the dryer to the main power while observing the relevant safety regulations of your area. English What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the parts, contact a local Samsung customer center or the retailer.
Installation Parts supplied English Y-connector Water hose (Canadian elec. models only) Short water hose Tools needed for installation Pliers Cutting knife Pipe wrench (gas models only) Nut screwdriver Level Phillips screwdriver Duct tape Wrench LPG-safe compound or Teflon Tape (for gas installation) WARNING Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.
Step-by-step installation English Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. • Do not remove the protective film on the door before completing the product installation. If you remove the protective film before the installation is complete, the door may get scratched or damaged during installation. • Make sure the installation location allows enough space for the dryer door to be fully open. STEP 1 Install the exhaust system 1.
Installation STEP 3 Connect the electrical wiring (for electric models) English Before connecting the electrical wiring, make sure you have read the “Electrical requirements” section on page 21. 3-wire system 1. Loosen or remove the screws from the center terminal block. 2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block. Tighten the screws. 3. Connect the other wires to outer terminal block screws. Tighten the screws.
4-wire system English 1. Remove the external ground connector’s screw and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION F D A B C L2 L1 E A. External ground connector B. Neutral grounding wire (white) C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. 3/4” (1.9 cm) UL-listed strain relief -- To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
Installation STEP 4 Connect the water hose English The dryer must be connected to a cold water tap using the provided water hoses. 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the female end of the Y-connector to the cold water tap. 2. Connect the straight end of the water hose to the Y-connector. Tighten the hose coupling by hand. 3. Using pliers, tighten the coupling an additional twothirds turn.
Using the short hose as an extension English 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight. 2. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten. You can damage the coupling. B 3. Connect the Y-connector (A) to the brass male end of the short hose. Turn the coupling by hand until it is tight.
Installation STEP 5 Level the dryer English To ensure optimal performance, the dryer must be level. A Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, turn the leveling feet (B) clockwise to lower the dryer or counterclockwise to raise the dryer.
STEP 6 Power on (for gas models) English Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 7 below. STEP 7 Final Check When installation is complete, confirm that: • • • • • • The dryer is plugged into an electrical outlet and grounded properly. The exhaust ductwork is connected, and the joints are taped.
Installation Vent blockage test English After the dryer is installed, run the Vent Blockage Test function to check if the duct system is properly installed. Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy. NOTE The Vent Blockage Test function must run when the dryer is cool.
Installation check codes Meaning English Check code No problems detected Solution Vent condition is good. 1. Clean the lint filter. Vent is nearly clogged Over 80 % of the vent is clogged. (This may lead to poor drying performance or cause malfunction) Leave the dryer at room temperature The internal temperature of the dryer is too low (below 32 °F (0 °C)) or too high (over 104 °F (40 °C)) and therefore vent blockage cannot be detected.
Installation Exhaust ducting guide English Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping screws. 3. To facilitate the exhaust, keep the ducts as straight as possible. Cleaning Clean all old ducts before installing the dryer, and make sure the vent flap opens and closes freely. We recommend that you clean the exhaust system annually or on a regular basis.
English 6. Remove the two screws above and below the lever holder on the opposite side of the door opening. 7. Remove the two screws that hold the lever holder in place, and then remove the lever holder. 8. Re-insert the two screws that held the lever holder into the same screw holes, and then tighten. 9. Remove the single screw from the back of the door hinge.
Installation English 10. Insert the screw you just removed into the other screw hole on the back of the door hinge, and then tighten. 11. Place the door on the other side, and then reattach it to the dryer. NOTE Insert the head of the screw on the back of the hinge into the hole above the cut out in the frame, and then slide the door hinge down until it stops. Make sure the protrusion on the back of the hinge is pressed into the cut out before you tighten the hinge screws. 12.
Before you start Here are a few things you should know before starting your dryer. English Initial setup • When you turn on your dryer for the first time, the screen shows the initial setup process. Follow the on-screen instructions to complete it. • If you complete the initial setup and operate a cycle for more than a minute, the initial setup will not appear again. • The initial setup includes language selection and a brief tutorial. • When tapping a button, tap exactly over the text.
Before you start Sort and load English • • • • • • • • Put one wash load in the dryer at a time. Do not mix heavy and lightweight items together. To improve drying efficiency for one or two items, add a dry towel to the load. For best results, untangle items before inserting them into the dryer. Tangled items may degrade the drying efficiency or cause the door to open. Overloading reduces the tumbling action, resulting in uneven drying and wrinkling.
Operations WARNING English To reduce the risk of fire, electric shock, or injury, read the “Safety information” before operating this appliance. Control panel 04 10 02 01 03 05 06 07 08 09 Tap to turn the dryer on or off. 01 Power • If you do not manipulate the control panel for 10 minutes after the dryer is turned on, the dryer automatically turns off. • The dryer automatically turns off when the drying completes. CAUTION Do not tap to turn the dryer off while the drying is in progress.
Operations English 07 Temp. Temperature can only be adjusted in Time Dry cycle. Tap to change the temperature of the current cycle. 08 Time Tap to select the cycle time for Small Load, Time Dry, Rack Dry, Air Fluff or Wrinkle Away. You can set the drying time between 10 minutes and 90 minutes. Available drying time depend on the selected cycle. 09 Options • Tap to enter the Options menu. • Tap and hold for 3 seconds to enter the System Functions menu.
Operating a cycle English 02 01 06 05 1. Tap 03 04 to turn on the dryer. 2. Turn the Navigation dial to select the cycle you want. For more information on “Cycle overview”, see page 42. 3. Tap Dryness, Temp., or Time to change the default cycle settings. 4. Tap Options, and then turn the Navigation dial to select additional function. For more information on “Options”, see page 44. 5. Tap OK to change the settings for selected additional function. Not all cycles have additional features available.
Operations Cycle overview English NOTE Other cycles can be used after adding them to your cycle list using the My Cycles function. For more information, see the “My Cycles” section on page 46. Cycle Description Normal For most fabrics including cottons and linens. SuperSpeed Fast & effective for synthetic fabrics. Small Load Timed cycle for small load items. The default cycle time is 30 minutes. However, you may manually change the cycle time if necessary. Eco Normal For reducing energy usage.
Cycle Description English Wrinkle Away (Manual Dry) For best results, load 2-3 items at once. You can extend the drying time by a 10-minute unit (starting from a minimum of 20 minutes), depending on the item type or load. Confirm that the laundry load is dry. Time Dry You can specify a cycle time by a 10-minute unit. Rack Dry Timed cycle for items that needs to be dried on a drying rack. Turn Navigation dial to select Rack Dry and tap Time to set the drying time between 10 minutes and 90 minutes.
Operations Options English Using Options 02 03 01 1. Tap Options. 2. Turn the Navigation dial to select the desired additional function. 3. Tap OK to change the selected function’s settings or start the function. NOTE • To return to the main screen, tap Options again or turn the Navigation dial to select Back and tap OK. • If the selected function is not supported, the "Currently not supported" message is displayed, and the OK button is not activated.
Damp Alert English This function alerts you when shirts and other items that require ironing are dry enough to be suitable for ironing. 1. Select a cycle and change the cycle settings as necessary. -- This function is available for Normal, Heavy Duty, Bedding, Delicates, Perm Press, Towels and Denim with Dryness set to 2-5. 2. Tap Options. 3. Turn the Navigation dial to select Damp Alert, and then tap OK. 4. Tap OK to select On or Off. Alarm during drying: 1. Tap and hold to pause the cycle. 2.
Operations My Cycles English Add or remove cycles to create a personal cycle list. 1. Tap Options. 2. Turn the Navigation dial to select My Cycles, and then tap OK. -- You can only edit a cycle to create a personal cycle when the dryer is not operating. 3. Turn the Navigation dial to select a desired cycle. 4. Tap OK to add or remove the selected cycle. -- Addition and removal of a cycle is saved automatically. 5. Tap Options or select Back to finish My Cycles setting.
System functions English Using System Functions 02 01 * 03 * Tap and hold 3 seconds. 1. Tap and hold Options for 3 seconds. 2. Turn the Navigation dial and select the desired system function, and then tap OK. 3. Tap OK to change the selected function’s settings or start the function. NOTE • To return to the main screen, tap Options again or turn the Navigation dial to select Back and tap OK.
Operations Alarm English You can enable/disable alarm sounds. 1. Tap and hold Options for 3 seconds. 2. Turn the Navigation dial to select Alarm, and then tap OK. 3. Tap OK to select On or Off. -- The default setting is On. NOTE The setting remains unchanged even if you restart the dryer. Wi-Fi You can turn the dryer's Wi-Fi on or off. 1. Tap and hold Options for 3 seconds. 2. Turn the Navigation dial to select Wi-Fi, and then tap OK. 3. Tap OK to select On or Off.
Special features English Smart Control You can connect to the SmartThings app and control your dryer remotely. (Smart Control for electric model, Smart Monitor for gas model) Connecting your dryer • Download and open the SmartThings app on your mobile device • Tap to turn on the dryer. • Tap and hold Smart Control / Smart Monitor on the dryer. a. The dryer enters AP mode and connects to your mobile device. b. Tap Smart Control / Smart Monitor to authenticate your dryer on your mobile device. c.
Operations SmartThings English Wi-Fi connection On your smartphone, go to Settings and turn on the wireless connection and select an AP (Access Point). • This appliance supports the Wi-Fi 2.4 GHz protocols. Download On an app market (Google Play Store, Apple App Store, Samsung Galaxy Apps), find the SmartThings app with a search term of “SmartThings”. Download and install the app on your device. NOTE The app is subject to change without notice for improved performance.
Cycle chart English NOTE For best results, follow the load size recommendations for each dry cycle. • Large load: Fill the drum to about 3/4 full. Do not add items over this level as they need to tumble freely. • Medium load : Fill the drum to about 1/2 full. • Small load : Fill the drum with 3-5 items, not more than 1/4 full.
Operations NOTE English : factory setting, : can be selected Cycle Functions (Temp.
Drying guide English The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference. Items Description Follow the care label instructions or dry using Bedding. Bedspreads & Comforters Blankets Curtains & Draperies • Make sure the item is thoroughly dry before using or storing. • May require repositioning in the drum to ensure even drying. Use Normal and dry only one blanket at a time for best tumbling action.
Maintenance Keep the dryer clean for best performance and to lengthen its life cycle. WARNING English Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. Cleaning Control panel Dryer exterior • Clean with a soft, damp cloth. Do not use abrasive substances.
Troubleshooting Checkpoints English If you encounter a problem with the dryer, first check the table below and try the suggestions. Problem Dryer does not start. The dryer does not warm up. Action • • • • • • Make sure the dryer is plugged in. Make sure the door is properly closed. Check the fuse or reset the circuit breaker. If you opened the door during a cycle, tap and hold Clean the filter. Make sure Child Lock is not activated. • • • • • • Check your home’s circuit breakers or fuses.
Troubleshooting Problem Action English The dryer is too loud. • Look for coins, loose buttons, nails, and other objects and remove them immediately. • Check the lint filter. Remove any items stuck inside the lint filter. • Make sure the dryer is level and standing firmly on the floor. • The dryer may hum due to air moving through the drum and fan. This is normal. • It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle. Items are not dried evenly.
Problem English Extended time. Action • Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level is reached. The drying time can change according to the type and amount of laundry. See the cycle chart for reference. If a problem persists, contact a local Samsung service center. Information codes If the dryer fails to operate, you may see an information code on the display panel.
Troubleshooting Information code Action tC5 The Thermistor2 resistance is very low or high. • Check for a clogged lint screen. • Check if the vent system is restricted. • If this information code remains, contact a Samsung service center. dF Incorrect door switch. Contact a Samsung service center. 3C The PBA needs to be checked. • Unplug the power plug and contact a Samsung service center. English Meaning If any information code keeps appearing on the display, contact a Samsung service center.
Specifications Fabric care chart Wash cycle Normal Permanent press/Wrinkle resistant/ Wrinkle control English The following symbols provide garment care direction. The clothing care labels include symbols for drying, bleaching, ironing, and dry cleaning. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to optimize garment life and reduce laundering problems.
Specifications Warning symbols for laundering Dry-clean English Do not wash Dry-clean Do not wring Do not dry-clean Do not bleach Line dry / Hang to dry Do not tumble dry Drip dry No steam (added to iron) Dry flat Do not iron Protecting the environment This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source.
LIMITED WARRANTY (U.S.A.) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL CONSUMER PURCHASER WITH PROOF OF PURCHASE This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
LIMITED WARRANTY (U.S.A.) Visits by an authorized servicer to explain product functions, maintenance or installation are not covered by this limited warranty. Please contact SAMSUNG at the number below for assistance with any of these issues. EXCLUSION OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW.
Warranty (CANADA) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.
Warranty (CANADA) EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
Memo Untitled-1 65 2020-12-15 2:46:49
Memo Untitled-1 66 2020-12-15 2:46:49
Memo Untitled-1 67 2020-12-15 2:46:49
Scan this with your smartphone This product qualifies for ENERGY STAR in the factory default "Normal + Eco dry" setting. If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com/us/support CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca/support (English) www.samsung.