Dryer User manual DVE(G)50R8500*/DVE(G)50A8500* Untitled-6 1 2023-12-19( ) 12:33:53
Contents Safety information 4 What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING IMPORTANT SAFETY INSTRUCTIONS Warnings Cautions 4 4 7 8 9 9 Regulatory notice 11 FCC Notice IC Notice Open Source Announcement To turn on the Wi-Fi connection for your dryer 11 11 13 13 Installation requirements 14 Key installation requirements Location considerations Ducting requirements Exhausting requirements Gas requirements Electrical requirements 14 14
Operations 42 Control panel Simple steps to start Cycle overview Cycle chart Drying guide Special features SmartThings 42 45 46 48 50 51 53 Maintenance 54 Vent sensor Cleaning 54 55 Troubleshooting 56 Checkpoints Information codes 56 59 Specifications 60 Fabric care chart Protecting the environment Specification sheet 60 61 61 English Untitled-6 3 2023-12-19( ) 12:33:53 3
Safety information Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features. What you need to know about the safety instructions Please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance.
WARNING - Risk of Fire • Clothes dryer installation must be performed by a qualified installer. • Install the clothes dryer according to the manufacturer’s instructions and local codes. • Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint.
Safety information WARNING - To reduce the risk of fire or explosion: • Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed.
WARNING - Fire or explosion hazard • Failure to follow safety warnings exactly could result in serious injury, death or property damage. • Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance. • Installation and service must be performed by a qualified installer, service agency, or the gas supplier. • Do not install a booster fan in the exhaust duct. WARNING - What to do if you smell gas: • • • • • • Do not try to light any appliance.
Safety information IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapours that could ignite or explode. 3.
Warnings WARNING • Ensure pockets are free of small, irregularly shaped hard objects and foreign material, i.e. coins, knives, pins, etc. These objects could damage your dryer. • Gas leaks may occur in your system, resulting in a dangerous situation. Cautions CAUTION • Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets.
Safety information • Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat from escaping and can create a fire hazard.
Regulatory notice FCC Notice CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received including interference that cause undesired operation.
Regulatory notice 2. This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. For products sold in the US and Canadian markets, only channels 1–11 are available. You cannot select any other channels.
Open Source Announcement The software included in this product contains open source software. You may obtain the complete corresponding source code for a period of three years after the last shipment of this product by sending an email to mailto:oss.request@samsung.com. It is also possible to obtain the complete corresponding source code in a physical medium such as a CDROM; a minimal charge will be required. The following URL http://opensource.samsung.
Installation requirements Read through the following instructions before installing the dryer and keep this manual for future reference. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. Key installation requirements • • • • A grounded electrical outlet. A power cord for electric dryers (except in Canada).
Dimensions U A 9 Type Dimensions (in. (mm)) Front loading dryer A. Overall height 38.7 (984) B. Width 27.0 (686) C. Depth with door open 52.8 (1340) D. Depth 31.
Installation requirements Clearance requirement This clearance requirement is applicable for dryers only. NOTE • For washer's clearance requirement, see the washer's user manual. • If the washer and dryer have different clearance requirements, use the one with the larger value. Alcove or closet installations WARNING • The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or closet.
Undercounter installation A 39.6 in. (1006 mm) B 1 in. (25 mm) C 1 in. (25 mm) A 5.9 in. (150 mm) B 6 in. (152 mm) C 52.8 in.
Installation requirements This clearance requirement is applicable for washer and dryer pair installation. Side by side installation Stacked installation (Model: SKK-8K) 9 U k 9 A 1 in. (25 mm) B 5.9 in. (150 mm) C 7.3 in. (185 mm) D 6 in. (152 mm) E 78.5 in. (1994 mm) A NOTE Stacking (MODEL NO: SKK-8K) Many of Samsung's washers and dryers can be stacked to maximize usable space. You can purchase an optional stacking kit from your Samsung retailer.
Ducting requirements Recommended Use only for short-run installation 4” (10.2 cm) 2.5” (6.4 cm) Weather hood type No. of 90° elbows Rigid Rigid 0 80 ft. (24.4 m) 74 ft. (22.6 m) 1 68 ft. (20.7 m) 62 ft. (18.9 m) 2 57 ft. (17.4 m) 51 ft. (15.5 m) 3 47 ft. (14.3 m) 41 ft. (12.5 m) NOTE * Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.
Installation requirements Exhausting requirements The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. In the United States and Canada • All dryers must be exhausted to the outside. • The required exhaust duct is 4 inches (10.2 cm) in diameter.
Gas requirements WARNING • Use only natural or LP (liquid propane) gases. • The installation must be conformed with local codes, or in the absence of local codes, with the national fuel gas code, ANSI Z223.1/NFPA 54, latest revision(for the UNITED STATES), or with the natural gas and propane installation code, CSA B149.1(for Canada) • Gas dryers are equipped with a burner vent for use with natural gas.
Installation requirements Commonwealth of Massachusetts installation instructions Your dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install your dryer, the connector can be no longer than 3’ (36”). WARNING • • • • Gas leaks may occur in your system, creating a dangerous situation. Gas leaks may not be detected by smell alone.
Grounding This dryer must be grounded. In the event of a malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for the electrical current. Gas models WARNING • Your dryer has a cord with an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Installation requirements Electrical connections Before operating or testing, follow all grounding instructions in the “Grounding” section. An individual branch (or separate) circuit serving only your dryer is recommended. Do not use an extension cord. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service.
Installation This dryer must be installed by a qualified technician. The installer is responsible for connecting the dryer to the main power while observing the relevant safety regulations of your area. What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the parts, contact a local Samsung customer center or the retailer.
Installation Parts supplied Y-connector Water hose (Canadian elec. models only) Short water hose Tools needed for installation Pliers Cutting knife Pipe wrench (gas models only) Nut screwdriver Level Phillips screwdriver Duct tape Wrench LPG-safe compound or Teflon Tape (for gas installation) WARNING Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.
Step-by-step installation Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. • Do not remove the protective film on the door before completing the product installation. If you remove the protective film before the installation is complete, the door may get scratched or damaged during installation. • Make sure the installation location allows enough space for the dryer door to be fully open. STEP 1 Install the exhaust system 1.
Installation STEP 3 Connect the electrical wiring (for electric models) Before connecting the electrical wiring, make sure you have read the “Electrical requirements” section on page 22. 3-wire system 1. Loosen or remove the screws from the center terminal block. 2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block. Tighten the screws. 3. Connect the other wires to outer terminal block screws. Tighten the screws.
4-wire system 1. Remove the external ground connector’s screw and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION F D A B C L2 L1 E A. External ground connector B. Neutral grounding wire (white) C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. ¾” (1.9 cm) UL-listed strain relief -- To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
Installation STEP 4 Connect the water hose The dryer must be connected to a cold water tap using the provided water hoses. 1. Connect the angled end of the water hose to the filling valve at the bottom rear of the dryer. Turn the coupling by hand until it is tight. 2. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten. You can damage the coupling. 3.
Using the short hose as an extension 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight. 2. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten. You can damage the coupling. B 3. Connect the Y-connector (A) to the short hose. Turn the coupling by hand until it is tight. 4.
Installation STEP 5 Level the dryer To ensure optimal performance, the dryer must be level. A Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, turn the leveling feet (B) clockwise to lower the dryer or counterclockwise to raise the dryer.
STEP 6 Power on (for gas models) Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 7 below. STEP 7 Final Check When installation is complete, confirm that: • • • • • • The dryer is plugged into an electrical outlet and grounded properly. The exhaust ductwork is connected, and the joints are taped.
Installation Running the vent blockage test 1. Make sure the drum is empty, and then close the door. (If there are any clothes or other items in the drum, the test will not give accurate results.) 2. Press the Power button to turn the dryer on, then simultaneously press and hold the Adjust Time and Dryness buttons for 3 seconds. “InS” appears in the dryer’s display. (If you have started other procedures before the Vent Blockage Test, the dryer will not enter the Vent Blockage Test mode.) 3.
Installation check codes Check code Meaning 0 Vent condition is good. Clg (Cg) The vent is clogged. C80 (C8) C90 (C9) Solution About 80 % of the vent is clogged. 1. Clean the lint filter. (This may decrease the drying performance.) 2. Check your vent condition. (Refer to the “Ducting requirements” section) Over 90 % of the vent is clogged. * You must take measures (such as cleaning) through expert personnel.
Installation Exhaust ducting guide Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping screws. 3. To facilitate the exhaust, keep the ducts as straight as possible. Cleaning Clean all old ducts before installing the dryer, and make sure the vent flap opens and closes freely. We recommend that you clean the exhaust system annually or on a regular basis.
6. Remove the two screws above and below the lever holder on the opposite side of the door opening. 7. Remove the two screws that hold the lever holder in place, and then remove the lever holder. 8. Re-insert the two screws that held the lever holder into the same screw holes, and then tighten. 9. Remove the single screw from the back of the door hinge. NOTE This is the screw that supports the door against the frame so you can unscrew or screw in the hinge without needing to support the door yourself.
Installation 10. Insert the screw you just removed into the other screw hole on the back of the door hinge, and then tighten. 11. Place the door on the other side, and then reattach it to the dryer. NOTE Insert the head of the screw on the back of the hinge into the hole above the cut out in the frame, and then slide the door hinge down until it stops. Make sure the protrusion on the back of the hinge is pressed into the cut out before you tighten the hinge screws. 12.
Before you start Here are a few things you should know before starting your dryer. Sort and load • • • • • • • • Put one wash load in the dryer at a time. Do not mix heavy and lightweight items together. To improve drying efficiency for one or two items, add a dry towel to the load. For best results, untangle items before inserting them into the dryer. Tangled items may degrade the drying efficiency or cause the door to open.
Before you start Rack Dry (applicable models only) Some models come with a drying rack which is inserted into the drum at the factory. If your model came with a drying rack, remove the rack from the drum before you use the dryer for the first time. To remove the rack, pull the rack straight up, and then take it out of the drum. Remove the drying rack from its packaging and store the rack for later use. If a drying rack is not provided, you can purchase it at a local Samsung service center.
Drying rack drying suggestions Item Cycle settings Washable sweaters (fold sweater into same shape as rack and lay it flat on the rack) TIME DRY with the Low temperature setting Stuffed toys (cotton or polyester fiber-filled) Stuffed toys (foam or rubber-filled) Foam rubber pillows AIR FLUFF Sneakers WARNING • Make sure to unpack the drying rack before using it. Otherwise, the dryer can be damaged or its performance diminished.
Operations WARNING To reduce the risk of fire, electric shock, or injury, read the “Safety information” before operating this appliance.
Turn the Cycle Selector to select the desired cycle. The indicator by the cycle name lights up. 01 Cycle Selector • Steam Cycles: The dryer sprays water into the drum to deodorize clothes and reduce static electricity and wrinkles. • Manual Dry: The drying time is fixed. 02 Digital Graphic Display Displays all cycle information, including the cycle time, information code, and operating status. Press to select a dry level. You can select from 5 different options (Less to More).
Operations This alert is available for all Sensor Dry cycles except for ACTIVEWEAR. Available dry levels are Normal, More, and Extra. 08 Damp Alert If a load contains mixed fabrics, the Damp Alert indicator blinks when average dryness of the items in the load is 80 % dry. This lets you take items that you don’t want fully dried or that dry quickly out of the dryer early while letting others continue to dry. 09 Drum Light Press to turn the interior lamp on or off.
Icon description Sensor Dry This icon appears when the dryer operates the cycle which senses the internal humidity to determine the drying time. Filter Check This icon displays after every load as a reminder to clean the lint filter. Clean the lint filter before every cycle and make sure the filter is properly inserted before starting a cycle. Vent Sensor The dryer features a vent sensor that detects and notifies you when it is time to clean the ductwork.
Operations Cycle overview Standard Cycles Cycle Description For most fabrics including cottons and linens. NORMAL If Normal is selected, the Eco Dry function is enabled by default. For more information, see Eco Dry in the “Control panel” section. HEAVY DUTY For drying items made out of heavy fabrics, such as jeans, corduroys, or work clothes, with high temperature heat. BEDDING For bulky items such as blankets, sheets, and comforters.
Manual Dry You can change the drying settings manually to your preference. Cycle QUICK DRY Description A quick drying cycle that runs for 30 minutes. You can specify a cycle time in minutes. TIME DRY If TIME DRY is selected, the Eco Dry function is enabled by default. For more information, see Eco Dry in the “Control panel” section. AIR FLUFF Tumbles the load in room temperature air.
Operations Cycle chart NOTE For best results, follow the load size recommendations for each dry cycle. • Large load: Fill the drum to about 3/4 full. Do not add items over this level as they need to tumble freely. • Medium load : Fill the drum to about 1/2 full. • Small load : Fill the drum with 3-5 items, not more than 1/4 full.
NOTE : factory setting, : can be selected Functions (Temp.
Operations Drying guide The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference. Items Description Follow the care label instructions or dry using Bedding. Bedspreads & Comforters Blankets Curtains & Draperies • Make sure the item is thoroughly dry before using or storing. • May require repositioning in the drum to ensure even drying. Use Normal and dry only one blanket at a time for best tumbling action.
Special features Child Lock Child Lock prevents children from playing with the dryer. When Child Lock is activated, all buttons except for the Power button are disabled. To activate/deactivate Child Lock, simultaneously press and hold Dryness and Temp. for 3 seconds. NOTE Once Child Lock is activated, it will remain active even after you restart the dryer. If other buttons, except for the Power button, do not respond, check the Child Lock indicator.
Operations Alarm off You can turn the alarm on or off. When the alarm is off, the melody of cycle completion and the power-off beep will not sound. However, the other sounds stay active. • Press and hold Drum Light for 3 seconds to turn the alarm on or off. • Your setting will be retained even after you turn off the dryer. You can turn the alarm back on by pressing and holding the same button for 3 seconds.
SmartThings Wi-Fi connection On your smartphone, go to Settings, turn on the wireless connection, and then select your AP (Access Point). • This appliance supports the Wi-Fi 2.4 GHz protocols. Download On an app market (Google Play Store, Apple App Store, Samsung Galaxy Apps), find the SmartThings app using the search term “SmartThings”. Download and install the app on your device. NOTE The app is subject to change without notice for improved performance.
Maintenance Keep the dryer clean to prevent decreased performance and to lengthen its life. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. Vent sensor The dryer features a vent sensor that detects and notifies you when it is time to clean the ductwork. The indicator lets you know the status of the duct.
Cleaning Control panel Dryer exterior • Clean with a soft, damp cloth. Do not use abrasive substances. • Do not spray liquid cleaning agents directly onto the dryer display. • Some laundry pre-treatment soil and stain removers may damage the control panel. • When using liquid cleaning agents, apply them to the cleaning cloth. Do not apply them directly to the dryer. Wipe up any spills or overspray immediately. • Clean with a soft, damp cloth. Do not use abrasive substances.
Troubleshooting Checkpoints If the dryer operates abnormally, first check the list of problems in the table below and try the suggested actions. Problem Does not run. Does not heat. Does not dry. 56 Untitled-6 56 Action • • • • Make sure the door is latched shut. Make sure the power cord is plugged into a live electrical outlet. Check your home’s circuit breakers or fuses. Press or tap Start/Pause (Hold to Start) again if the door was opened during a cycle. • Clean the lint filter.
Problem Action Is noisy. • Check the load for objects such as coins, loose buttons, nails, etc. Remove promptly. • It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle. • Make sure the dryer is leveled properly as outlined in the installation instructions. • It is normal for the dryer to hum due to the high velocity of air moving through the dryer drum, fan, or exhaust system. Dries unevenly.
Troubleshooting Problem Action Sprayed water is not visible during Steam cycles. • Sprayed water is difficult to see when the door is closed. Extended time. • Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level is reached. The drying time can change according to the type and amount of laundry. See the cycle chart for reference. If a problem persists, contact a local Samsung service center.
Information codes If the dryer fails to operate, you may see an information code on the display panel. To determine what you should do, check the list of codes in the table below, and then try the suggested actions. Code Action Operating the dryer with the door open. dC • Make sure the door is properly closed. • Make sure laundry is not caught in the door. Invalid power source frequency. FC AC • Try restarting the cycle. • If this information code remains, contact a Samsung service center.
Specifications Fabric care chart The following symbols provide garment care direction. The clothing care labels include symbols for drying, bleaching, ironing, and dry cleaning. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to optimize garment life and reduce laundering problems.
Warning symbols for laundering Dry-clean Do not wash Dry-clean Do not wring Do not dry-clean Do not bleach Line dry / Hang to dry Do not tumble dry Drip dry No steam (added to iron) Dry flat Do not iron Protecting the environment This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source.
LIMITED WARRANTY (U.S.A.) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL CONSUMER PURCHASER WITH PROOF OF PURCHASE AND/ OR PROOF OF DELIVERY This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
This limited warranty covers manufacturing defects in materials or workmanship encountered in normal household, noncommercial use of this product and shall not cover the following: damage that occurs in shipment, delivery, installation, and uses for which this product was not intended; damage caused by unauthorized modification or alteration of the product; product where the original factory serial numbers have been removed, defaced, changed in any way, or cannot be readily determined; cosmetic damage inclu
LIMITED WARRANTY (U.S.A.) LIMITATION OF REMEDIES YOUR SOLE AND EXCLUSIVE REMEDY IS PRODUCT REPAIR, PRODUCT REPLACEMENT, OR REFUND OF THE PURCHASE PRICE AT SAMSUNG’S OPTION, AS PROVIDED IN THIS LIMITED WARRANTY.
Warranty (CANADA) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.
Warranty (CANADA) EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
Memo Untitled-6 67 2023-12-19( ) 12:34:07
Scan this with your smartphone This product qualifies for ENERGY STAR in the factory default "Normal + Eco dry" setting. If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR. QUESTIONS OR COMMENTS? COUNTRY CALL U.S.A 1-800-SAMSUNG (726-7864) CANADA 1-800-SAMSUNG(726-7864) OR VISIT US ONLINE AT www.samsung.com/us/support www.samsung.com/ca/support (English) www.samsung.