Dryer User manual DVE(G)55A7700*/DVE(G)55A7300*/DVE(G)52A5500* Untitled-1 1 2021-04-05 10:16:06
Contents Contents Safety information 4 What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING Important safety precautions Warnings Cautions 4 4 5 5 8 8 Regulatory notice 10 FCC Notice IC Notice Open Source Announcement 10 11 12 Installation requirements 13 Key installation requirements Location considerations Ducting requirements Exhausting requirements Gas requirements Electrical requirements 13 13 17 18 19 20 Installation 23 What’s i
42 Control panel Simple steps to start Cycle overview Cycle chart Cycle guide Special features 42 45 46 48 51 52 Maintenance 54 Cleaning 54 Troubleshooting 55 Checkpoints Information codes 55 58 Specifications 60 Fabric care chart Protecting the environment Specification sheet 60 61 62 Contents Operations English 3 Untitled-1 3 2021-04-05 10:16:07
Safety information Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features. What you need to know about the safety instructions Safety information Please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance.
WARNING - Risk of Fire • • • Safety information • • Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer’s instructions and local codes. Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
Safety information 6. Before the appliance is removed from service or discarded, remove the door to the drying compartment. 7. Do not reach into the appliance if the drum is moving. 8. Do not install or store this appliance where it will be exposed to the weather. 9. Do not tamper with internal controls. Safety information 10.
WARNING - To reduce the risk of fire or explosion: • Safety information • Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed.
Safety information Warnings WARNING • Safety information • Ensure pockets are free from small, irregularly shaped hard objects, foreign material, etc. ie. coins, knives, pins, etc. These objects could damage your dryer. Gas leaks may occur in your system, resulting in a dangerous situation. Cautions CAUTION • • • • • • • • • • • • • • • • Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets.
• • Safety information • Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil. Even after being washed, these items may contain significant amounts of these oils. Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur.
Regulatory notice FCC Notice CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1. This device may not cause harmful interference, and Regulatory notice 2. This device must accept any interference received including interference that cause undesired operation.
Unintentional emitter per FCC Part 15 Product type : Clothes Dryers Model : DVE55A7300* Responsible Party – U.S. Contact Information Regulatory notice Samsung Electronics America, Inc. QA Lab America 19 Chapin Rd. Building D Pine Brook NJ 07058 Tel: 1-973-808-6375 Fax: 1-973-808-63 IC Notice The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: 1.
Regulatory notice Open Source Announcement The software included in this product contains open source software. You may obtain the complete corresponding source code for a period of three years after the last shipment of this product by sending an email to mailto:oss.request@samsung.com. It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM; a minimal charge will be required. Regulatory notice The following URL http://opensource.samsung.
Installation requirements Read through the following instructions before installing the dryer, and keep this manual for future reference. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. Key installation requirements A grounded electrical outlet. A power cord for electric dryers (except in Canada).
Installation requirements Dimensions A U Installation requirements 9 Type Front loading dryer Model A. Overall height Dimensions (in. (mm)) DVE(G)55A7**** DVE(G)52A5**** 45.3 (1150) 44.6 (1132) B. Width 27.0 (686) C. Depth with door open 50.1 (1273) D. Depth 30.
Clearance requirement This clearance requirement is applicable for dryers only. NOTE • • For washer's clearance requirement, see the washer's user manual. If the washer and dryer have different clearance requirements, use the one with the larger value. Alcove or closet installations WARNING • • The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or closet. No other fuel-burning appliance should be installed in the same closet as the dryer.
Installation requirements This clearance requirement is applicable for washer and dryer pair installation. Side by side installation B Installation requirements A A C A 1 in. (25 mm) B 21 in. (533 mm) C 1 in. (25 mm) D 5.9 in.
Ducting requirements Recommended Use only for short-run installation 4” (10.2 cm) 2.5” (6.4 cm) No. of 90° elbows Rigid Rigid 0 80 ft. (24.4 m) 74 ft. (22.6 m) 1 68 ft. (20.7 m) 62 ft. (18.9 m) 2 57 ft. (17.4 m) 51 ft. (15.5 m) 3 47 ft. (14.3 m) 41 ft. (12.5 m) Weather hood type Installation requirements NOTE * Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.
Installation requirements Exhausting requirements The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. Outside the United States and Canada • WARNING • In the United States and Canada • Installation requirements • • • • • All dryers must be exhausted to the outside. The required exhaust duct is 4 inches (10.
Gas requirements WARNING • • - • • 20,000 BTU: LPKIT-4/XAA (DC9804114A) - 22,000 BTU: LPKIT-3/XAA (DC9900792A) A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off valve be installed within 6” of your dryer. Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor. • • Additionally, a 1/8” (0.3 cm) N.P.T.
Installation requirements • Install and use in accordance with the manufacturer’s instructions. Electrical requirements The wiring diagram is located on the plate under the control panel or rear frame. WARNING • Installation requirements • • Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded.
Electric models WARNING • • • Before operating or testing, follow all grounding instructions in the “Grounding” section. An individual branch (or separate) circuit serving only your dryer is recommended. Do not use an extension cord. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required. Installation requirements • Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug.
Installation requirements WARNING Risk of Electric Shock Installation requirements When local codes allow, you can connect the dryer’s electrical supply with a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of 120 / 240 volts, 30-amperes with three No. 10 copper wire conductors terminated with closed loop terminals, open-end spade lugs with turned up ends, or with tinned leads.
Installation This dryer must be installed by a qualified technician. The installer is responsible for connecting the dryer to the main power while observing the relevant safety regulations of your area. What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the parts, contact a local Samsung customer center or the retailer.
Installation Parts supplied Y-connector Short water hose Tools needed for installation Cutting knife Pipe wrench (gas models only) Nut driver Level Phillips screwdriver Duct tape Wrench Installation Pliers LPG-safe compound or Teflon Tape (for gas installation) WARNING Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.
Step-by-step installation Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. • • Do not remove the protective film on the door before completing the product installation. If you remove the protective film before the installation is complete, the door may get scratched or damaged during installation. Make sure the installation location allows enough space for the dryer door to be fully open. STEP 1 Install the exhaust system 1.
Installation STEP 3 Connect the electrical wiring (for electric models) Before connecting the electrical wiring, make sure you have read the “Electrical requirements” section on page 20. 3-wire system 1. Loosen or remove the screws from the center terminal block. 2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block. Tighten the screws. D 3. Connect the other wires to outer terminal block screws. Tighten the screws.
4-wire system 1. Remove the external ground connector’s screw and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION F D A B C L2 L1 E B. Neutral grounding wire (white) C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. ¾” (1.9 cm) UL-listed strain relief F. Neutral wire (white or center wire) Installation A.
Installation WARNING • • • • All U.S. models are designed for a 3-wire system connection. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-wire system connection is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block. Remove the terminal block cover plate.
4. Connect the angled end of the water hose to the filling valve at the bottom of the rear frame. Turn the coupling manually until it is tight. 5. Using pliers, tighten the coupling an additional two-thirds turn. Do not overtighten because the coupling may be damaged. 6. If you detached the cold water hose from your washer, attach the hose to the open end of the Y-connector, tighten the coupling by hand until it is tight, and then, using a pliers, tighten an additional two-thirds turn. Installation 7.
Installation Using the short hose as an extension 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight. B 2. Using pliers, tighten the coupling an additional two-thirds turn. Do not overtighten because the coupling may be damaged. 3. Connect the Y-connector (A) to the brass male end of the short hose.
STEP 5 Level the dryer To ensure optimal performance, the dryer must be level. A Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, turn the leveling feet (B) clockwise to lower the dryer or counterclockwise to raise the dryer. Installation B NOTE • A B • To set the dryer to the same height as your washer, fully retract (A) the leveling feet by turning them counterclockwise, then loosen (B) the feet by turning them clockwise.
Installation STEP 6 Power on (for gas models) Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 7 below. STEP 7 Final check When installation is complete, confirm that: • • • • • The dryer is plugged into an electrical outlet and grounded properly. The exhaust ductwork is connected, and the joints are taped.
Vent blockage test After the dryer is installed, start the Vent Blockage Test to check if the duct system is properly installed. The Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy. NOTE The Vent Blockage Test must run when the dryer is cool. If the dryer warms up after the installation check, run the AIR FLUFF cycle for several minutes to reduce its internal temperature.
Installation • If the test result displays check code (the duct system is blocked ), refer to the “Ducting requirements” section on page 17 and the “Exhaust ducting guide” section below, and then take proper measures to correct any problems. If the test is suspended, it could result in incorrect results. Follow the proper procedures when testing the dryer. Even if the test result is normal (“End or 0”), the duct system could be blocked slightly.
Check code Meaning Solution Check the power connection. HC Detection of abnormal temperature in drum. Check the vent condition if the problem continue, contact a service center. Exhaust ducting guide Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping screws. 3. To facilitate the exhaust, keep the ducts as straight as possible.
Installation Switching the door position To reverse the direction of the door, we recommend that you contact a qualified technician. 1. Put a soft rug on the floor to rest the door on after you have removed it. This will prevent the door from being scratched. 2. Unplug the power cord of the dryer. 3. Remove the four hinge screws from the door, and then remove the door by lifting it up slightly. Installation 4. Remove the two screws from the lever holder, and then remove the holder cover. 5.
7. Locate and remove the 10 screws as shown. Note that screw B (x2) is longer than the others. B Installation 8. Remove the glass holder, and switch the positions of: a. the hinge cover and the door handle. b. the hinge holder and the glass-guide holder 9. Remove the door lever, and then move it to the other side as shown. 10.Remove the hole cover (C), and then insert and tighten the glass holder using the removed 10 screws. 11.Install the hole cover on the opposite side as shown.
Installation 12.Reinstall the door on the front frame, and then carefully insert and tighten the 4 hinge screws.
Before you start Here are a few things you should know before starting your dryer. Sort and load • • • • Put one wash load in the dryer at a time. Do not mix heavy and lightweight items together. To improve drying efficiency for one or two items, add a dry towel to the load. For best results, untangle items before inserting them into the dryer. Tangled items may degrade the drying efficiency or cause the door to open.
Before you start Rack Dry (applicable models only) Some models come with a drying rack which is inserted into the drum at the factory. If your model came with a drying rack, remove the rack from the drum before you use the dryer for the first time. To remove the rack, pull the rack straight up, and then take it out of the drum. Remove the drying rack from its packaging and store the rack for later use. If a drying rack is not provided, you can purchase it at a local Samsung service center.
Drying rack drying suggestions Item Washable sweaters (fold sweater into same shape as rack and lay it flat on the rack) Stuffed toys (cotton or polyester fiberfilled) Cycle settings TIME DRY with the Low temperature setting Stuffed toys (foam or rubber-filled) Foam rubber pillows AIR FLUFF Sneakers WARNING • • Make sure to unpack the drying rack before using it. Otherwise, the dryer can be damaged or its performance diminished.
Operations WARNING To reduce the risk of fire, electric shock, or injury to persons, read the “Safety information” before operating this appliance. Control panel DVE(G)55A7**** 02 07 10 12 08 01 03 04 05 09 11 07 10 13 06 DVE(G)52A5**** 02 12 Operations 08 01 09 03 04 05 11 13 06 Turn the Cycle Selector to select a desired cycle. When a cycle is selected, the cycle indicator lights up.
Press to select a dry level. You can select from 5 different options (Less to More). Please refer to following recommendations to select the appropriate dryness. 03 Dryness • • For larger or bulkier loads, select More for complete dryness. For items that needs to lay flat or hang to dry, use Less to partially dry items. NOTE This option is not available with REFRESH, STEAM SANITIZE , ACTIVEWEAR, TIME DRY, QUICK DRY, and AIR FLUFF. Temperature can only be adjusted in TIME DRY cycle.
Operations This alert is available for all Sensor Dry cycles except for ACTIVEWEAR. Available dry levels are Normal, More, and Extra. 08 Damp Alert 09 Drum Light 10 Adjust Time If a load contains mixed fabrics, the Damp Alert indicator blinks when average dryness of the items in the load is 80 % dry. This lets you take items that you don’t want fully dried or that dry quickly out of the dryer early while letting others continue to dry. Press to turn the interior lamp on or off.
Icon description Sensor Dry This icon appears when the dryer operates the cycle which senses the internal humidity to determine the drying time. Filter Check This icon displays after every load as a reminder to clean the lint filter. Clean the lint filter before every cycle and make sure the filter is properly inserted before starting a cycle. Vent Sensor (DVE(G)55A7**** models only) The dryer features a vent sensor that detects and notifies you when it is time to clean the ductwork.
Operations Cycle overview Standard Cycles Cycle Description For most fabrics including cottons and linens. NORMAL If NORMAL is selected, the Eco Dry function is enabled by default. For more information, see Eco Dry in the “Control panel” section. HEAVY DUTY For drying items made out of heavy fabrics, such as jeans, corduroys, or work clothes, with high temperature heat. BEDDING For bulky items such as blankets, sheets, and comforters.
Manual Dry You can change the drying settings manually to your preference. A quick drying cycle running for 30 minutes. QUICK DRY The default cycle time is 30 minutes. However, you may manually change the cycle time if necessary. You can specify a cycle time in minutes. TIME DRY AIR FLUFF If TIME DRY is selected, the Eco Dry function is enabled by default. For more information, see Eco Dry in the “Control panel” section. Tumbles the load in room temperature air.
Operations Cycle chart NOTE For best results, follow the load size recommendations for each dry cycle. • • • Large load: Fill the drum to about 3/4 full. Do not add items over this level as they need to tumble freely. Medium load : Fill the drum to about 1/2 full. Small load : Fill the drum with 3-5 items, not more than 1/4 full.
NOTE : factory setting, : can be selected Cycle Functions (Temp.
Operations DVE(G)55A7**** models Cycle Options Damp Alert Eco Dry Wrinkle Prevent NORMAL Adjust Time HEAVY DUTY BEDDING DELICATES PERM PRESS ACTIVEWEAR QUICK DRY TIME DRY AIR FLUFF STEAM SANITIZE REFRESH DVE(G)52A5**** models Cycle Options Adjust Time Damp Alert Eco Dry Wrinkle Prevent Operations NORMAL HEAVY DUTY BEDDING DELICATES PERM PRESS ACTIVEWEAR QUICK DRY TIME DRY AIR FLU
Cycle guide The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference. Cycle Bedspreads & Comforters Blankets Curtains & Draperies Cloth Diapers Description Follow the care label instructions or dry using BEDDING. • • Make sure the item is thoroughly dry before using or storing. May require repositioning in the drum to ensure even drying.
Operations Special features Child Lock Child Lock prevents children from playing with the dryer. When Child Lock is activated, all buttons except for the Power button are disabled. To activate/deactivate Child Lock, simultaneously press and hold Dryness and Temp. for 3 seconds. NOTE Once Child Lock is activated, it will remain active even after you restart the dryer. If other buttons, except for the Power button, do not respond, check the Child Lock indicator.
Smart Care To enable this function, you must first download the SmartThings app at the Play Store or the App Store and install it on a mobile device featuring a camera function. The Smart Care function has been optimized for Galaxy & iPhone series (applicable models only). 1. When the dryer detects an issue to check, an information code appears on the display. To enter Smart Care mode, press and hold Wrinkle Prevent for 3 seconds. 2.
Maintenance Keep the dryer clean for best performance and to lengthen its life cycle. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. Cleaning Control panel Powder coated drum • To clean the powder coated drum, use a damp cloth with a mild, non-abrasive cleaner suitable for easily marred surfaces.
Troubleshooting Checkpoints If the dryer operates abnormally, first check the list of problems in the table below and try the suggested actions. Problem Action • • Does not run. • • • • • • • • Does not heat. • Make sure the door is latched shut. Make sure the power cord is plugged into a live electrical outlet. Check your home’s circuit breakers or fuses. Press or tap Start/Pause (Hold to Start) again if the door is opened during a cycle. Clean the lint filter.
Troubleshooting Problem Action • • • Does not dry. • • • • • • • • • • Is noisy. • • Troubleshooting • Dries unevenly. • • Check all of the above, plus... Make sure the exhaust hood outside your home can open and close freely. Check the exhaust system for lint buildup. Ducting should be inspected and cleaned annually. Use a 4” rigid metal exhaust duct. Do not overload. 1 wash load = 1 dryer load. Dry heavy items and light weight items separately.
Problem Action • Has odors. • • • • • • • Small loads of 1 to 4 items work best. Load fewer items. Load similar-type items. Take out the items immediately after drying is complete. • This is steam condensation. The dripping water will stop after a short time. • Sprayed water is difficult to see when the door is closed. • Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level is reached.
Troubleshooting Information codes If the dryer fails to operate, you may see an information code on the display panel. To determine what you should do, check the list of codes in the table below, and then try the suggested actions. Code Action Operating the dryer with the door open. dC • • Make sure the door is properly closed. Make sure laundry is not caught in the door. Invalid power source frequency. FC AC • • Try restarting the cycle.
Code 3C Action The PBA needs to be checked. • Unplug the power plug and contact a Samsung service center. If any information code keeps appearing on the display, contact a Samsung service center.
Specifications Fabric care chart The following symbols provide garment care direction. The clothing care labels include symbols for drying, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to optimize garment life and reduce laundering problems.
Iron dry or steam temperatures Dry-clean High Dry-clean Medium Do not dry-clean Low Line dry / Hang to dry Warning symbols for laundering Drip dry Dry flat Do not wash Do not wring Do not bleach Do not tumble dry No steam (added to iron) Do not iron Protecting the environment This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations.
Specification Specification sheet Type Front loading dryer Capacity (Cu.ft) 7.4 Water pressure (psi (kPa)) 20-116 (137-800) Weight Heater rating lb (kg) 119.0 (54.
LIMITED WARRANTY (U.S.A.) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL CONSUMER PURCHASER WITH PROOF OF PURCHASE This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
LIMITED WARRANTY (U.S.A.
EXCLUSION OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific rights, and you may also have other rights, which vary from state to state.
Memo Untitled-1 66 2021-04-05 10:16:23
Memo Untitled-1 67 2021-04-05 10:16:23
Scan this with your smartphone Energy Star only applies to DVE(G)55A7**** model. This product qualifies for ENERGY STAR in the factory default "Normal + Eco dry" setting. If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG (726-7864) www.samsung.