DW80H99* Series DW80J99* Series DW80J75* Series Dishwasher installation guide These installation instructions are intended for use by qualified installers. STOP If you are having problems installing this dishwasher Please call : 1-800-SAMSUNG (726-7864) for assistance : www.samsung.com imagine the possibilities Thank you for purchasing this Samsung product. DD68-00151B-04 DW80H9950US-00151A-06_EN_150216.
safety instructions Throughout this manual, you will see Warning and Caution notes. The warnings, cautions, and the important safety instructions that follow do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Samsung is not liable for damages resulting from improper use.
GROUNDING INSTRUCTIONS For a permanently connected appliance: This appliance must be connected to grounded metal, a permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two or more people are needed to move a dishwasher and avoid potential injuries.
contents PREPARING THE DISHWASHER ENCLOSURE 5 5 Product dimensions Enclosure dimensions 6 8 15 16 18 20 21 STEP 1 Check the parts and tools STEP 2 Select the best location for the dishwasher STEP 3 Check water supply requirements and cautions STEP 4 Check the electrical requirements and cautions STEP 5 Unpacking and inspecting the dishwasher STEP 6 Preparing the dishwasher STEP 7 placing the dishwasher and connecting the hot water supply line STEP 8 Leveling the dishwasher STEP 9 Securing the dishwashe
preparing the dishwasher enclosure PRODUCT DIMENSIONS 70 ½ ” (670 mm) Rear view 33 7⁄8” (860mm) 01 PREPARING THE DISHWASHER Side view (DW80H995 series, DW80H994 series) 23 7⁄8” (605 mm) 20 ½” (520 mm) 25 ” (636mm) 5 ¾ ” (140mm) 2 ½ ” (60mm) Side view (DW80H997 series, DW80H993 series, DW80J994 series, DW80J755 series) 2 ¾” (70mm) The water supply line, power cable and drain hose should go through this space behind the dishwasher.
installing the dishwasher Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you are not at risk of injury when washing dishes. STEP 1 CHECK THE PARTS AND TOOLS Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. This will save installation time and simplify the installation process. Parts required Provided with the dishwasher. Check when you unbox the dishwasher in Step 5.
Tools required Safety glasses Gloves Flashlight Adjustable wrench Wire stripper Pliers Nipper Tape measure Pencil Phillips screwdriver Flat screwdriver Tubing cutter Cutting knife Hole saw Level Torx t20 Hex L-wrench 02 INSTALLING THE DISHWASHER Electric drill installing the dishwasher _7 DW80H9950US-00151A-06_EN_150216.
installing the dishwasher New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher. Repace the existing connections as necessary.
STEP 3 CHECK WATER SUPPLY REQUIREMENTS AND CAUTIONS • • The hot water supply line pressure must be between 20~120 psi (140~830 kPa). Adjust the water heater to deliver water between 120 ˚F (49 ˚C) ~ 149 ˚F (65 ˚C). - -
installing the dishwasher STEP 4 CHECK THE ELECTRICAL REQUIREMENTS AND CAUTIONS The electrical requirements for the dishwasher are as follows: • In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/Provincial and Municipal codes and/or local codes. • For cable direct connections.
STEP 5 UNPACKING AND INSPECTING THE DISHWASHER Unpack the dishwasher in an open area free of obstruction both around the packaging and overhead. We recommend that you retain all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product’s components from the packing materials prior to disposal. 02 INSTALLING THE DISHWASHER Unpacking 1. 2. 3. 4. Position the carton right-side-up with top arrows pointing upwards.
installing the dishwasher Plumbing 1. Check the hot water connection on the front left-side of the base of the dishwasher. The mounting plate should be secured to the front of the base, the threads inside the connection should be smooth and shiny, and the area should be clean and free of any debris. 2. Make sure the dish washer and the accessories are all included in the package to ensure these assemblies are not cracked and that all connections are secure. 3.
Insert the clamped drain hose into the holder hose. Tighten the clamp in the right position. Good The clamp is improperly connected. Tighten the clamp in the center of the assembly position. 02 INSTALLING THE DISHWASHER Bad To prevent damage to the drain hose that is designed to pass the product to the right, use the provided hose fixer and screw to secure the middle area of the drain hose to the product. Make sure to secure on the arrow-marked area.
installing the dishwasher STEP 7 PLACING THE DISHWASHER AND CONNECTING THE HOT WATER SUPPLY LINE 1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (See Step 8, Leveling the Dishwasher.) 2. Locate the hot water supply line and the power cable. 3. Place the dishwasher so that the hot water supply line is in the left channel and the power cable is in the right channel of the base of the dishwasher.
STEP 8 LEVELING THE DISHWASHER 02 INSTALLING THE DISHWASHER 1. Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level. See the first note below for instructions on adusting the height of the front legs. 2. Use the level to check if the dishwasher is level front to back, as shown in the figure to the right.
installing the dishwasher STEP 9 SECURING THE DISHWASHER You must fix the dishwasher to the countertop or cabinet side walls for additional stability and safety. 1. If the countertop is made of wood or the material will not be damaged by drilling, follow the instructions in 2-1 below. If the countertop is made of granite, marble, or any other material that can be damaged by drilling, follow the instructions in 2-2 below. 2-1.
installing the dishwasher STEP 10 CONNECTING THE DRAIN HOSE 1. Check the parts on the sink to which the drain hose will be connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures. You must connect the drain hose in accordance with the water pipe installation regulations in your region.
02 INSTALLING THE DISHWASHER 3. Check the size of the sink’s drain hose connector. If needed, cut the drain hose so its end fits onto the sink connector (½ in., ¾ in. or 1 in. - as shown in Figure 11 below). If the end of the drain hose does not fit onto the drain hose connector of the sink, use an adaptor purchasable at a plumbing/hardware supply store. 4. Slide a hose clamp over the end of the drain hose.
installing the dishwasher STEP 11 WIRING CONNECTIONS 1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is off. 2. In the junction box located at the front bottom right of the dishwasher, find the three power wires from the dishwasher including the grounding line. 3. Pass the power cable through the strain relief, and then into the junction box (Figure 13). 4. Connect the black wire of the dishwasher to the black wire of the power cable by insertng both into a wire nut.
STEP 12 COMPLETING THE INSTALLATION Check if the power turns on correctly and if there is any water leakage while the dishwasher the dishwasher, and then go to Step 5 below. refer to the user manual or contact a service center 1-800-SAMSUNG (726-7864). CAUTION Make sure to check for water leakage on both ends of the water supply line and drain hose connector. 5. Locate the sound absorber in front of base refer to the figure below (ON SOME MODELS).
specifications Power supply 120 V, 15 A, 60 Hz AC Water pressure 20 ~ 120 psi (140 ~ 830 kPa) Dimensions (Width×Depth×Height) 237⁄8 x 25 x 337⁄8 in. (605 x 636 x 860 mm) Minimum inlet water temperature 120 ˚F (49 ˚C) Specifications are subject to change without notice for quality improvement purposes. The actual appearance of the dishwasher may differ from the illustrations in this manual. 22_ specifications DW80H9950US-00151A-06_EN_150216.
note DW80H9950US-00151A-06_EN_150216.
QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT USA 1-800-SAMSUNG(726-7864) www.samsung.com/us/support CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca/support (English) www.samsung.com/ca_fr/support (French) Code No.: DD68-00151B-04_EN DW80H9950US-00151A-06_EN_150216.
Serie DW80H99* Serie DW80J99* Serie DW80J75* Lavavajillas guía de instalación Estas instrucciones de instalación están dirigidas a instaladores calificados. ATENCIÓN Si tiene problemas al instalar este lavavajillas llame al: 1-800-SAMSUNG(726-7864) para recibir asistencia: www.samsung.com imagine las posibilidades Gracias por comprar este producto Samsung. DW80H9950US-00151A-06_MES_150216.
instrucciones de seguridad A lo largo de este manual, encontrará notas de Advertencia y Precaución. Las siguientes advertencias, precauciones e instrucciones de seguridad importantes no cubren todas las posibles condiciones y situaciones que pueden ocurrir. Es su responsabilidad actuar con sentido común, precaución y cuidado cuando instale, realice el mantenimiento y ponga en funcionamiento el lavavajillas. Samsung no se responsabiliza por los daños ocasionados por el uso inadecuado.
INSTRUCCIONES DE CONEXIÓN A TIERRRA Para un electrodoméstico con conexión permanente: Este electrodoméstico debe estar conectado a un metal con conexión a tierra, un sistema de cableado permanente, o a un conductor con conexión a tierra del equipo a los conductores del circuito y a la terminal con conexión a tierra del equipo. El lavavajillas es muy pesado. No intente mover o trasladar un lavavajillas usted solo. Se necesitan dos o más personas para mover un lavavajillas y evitar lesiones potenciales.
contenido PREPARACIÓN DEL ESPACIO PARA EL LAVAVAJILLAS 5 5 Dimensiones del producto Dimensiones del espacio INSTALACIÓN DEL LAVAVAJILLAS 6 6 8 20 21 PASO 1 Verificación de las piezas y de las herramientas PASO 2 Elección de la mejor ubicación para el lavavajillas PASO 3 Verifique los requisitos para el suministro de agua y precauciones PASO 4 Verifique los requisitos eléctricos y advertencias PASO 5 Desempacar e inspeccionar el lavavajillas PASO 6 Preparación del lavavajillas PASO 7 Colocación del lava
preparación del espacio para el lavavajillas DIMENSIONES DEL PRODUCTO 70 ½” (670 mm) Vista posterior 33 7⁄8” (860 mm) 23 7⁄8” (605 mm) 20 ½” (520 mm) 25” (636 mm) 5 ¾” (140 mm) 2 ½” (60 mm) Vista lateral (Serie DW80H997, Serie DW80H993, Serie DW80J994, Serie DW80J755) 2 ¾” (70 mm) El conducto, el cable de alimentación y la manguera de desagüe deberían pasar por el espacio detrás del lavavajillas.
instalación del lavavajillas Asegúrese de que usted o su instalador siga estas instrucciones minuciosamente para que su nuevo lavavajillas funcione adecuadamente y no existan riesgos de sufrir lesiones al lavar los platos. PASO 1 VERIFICACIÓN DE LAS PIEZAS Y DE LAS HERRAMIENTAS Antes de comenzar la instalación, prepare todas las herramientas y piezas necesarias requeridas para instalar el lavavajillas. Esto ahorrará tiempo y simplificará el proceso de instalación.
Herramientas requeridas Lentes de seguridad Guantes Linterna Llave ajustable Alicate pelacable Pinza Alicate de corte Cinta métrica Lápiz Desarmador Phillips Desarmador plano Cortatubos Cúter Fresa para escariar Nivel Torx t20 Llave en forma de L para cabezas hexagonales 02 INSTALACIÓN DEL LAVAVAJILLAS Taladro eléctrico instalación del lavavajillas _7 DW80H9950US-00151A-06_MES_150216.
instalación del lavavajillas Instalación nueva Si la instalación del lavavajillas es nueva, la mayor parte del trabajo debe realizarse antes de colocar el lavavajillas en su lugar. Reemplazo Si el lavavajillas reemplazara a un lavavajillas anterior, debe verificar que las conexiones existentes sean compatibles con el nuevo lavavajillas. Reemplace las conexiones existentes si fuera necesario.
PASO 3 • • VERIFIQUE LOS REQUISITOS PARA EL SUMINISTRO DE AGUA Y PRECAUCIONES La presión del conducto de agua caliente debe estar entre 20 y 120 psi (140 y 830 kPa). Ajuste el calentador de agua para obtener una temperatura de agua entre 120 ˚F (49 ˚C) y 149 ˚F (65 ˚C). - El lavavajillas debe estar conectado al suministro de agua caliente con una temperatura entre 120 ˚F (49 ˚C) y 149 ˚F (65 ˚C). Este rango de temperatura ofrece un mejor resultado en el lavado y un ciclo más corto.
instalación del lavavajillas PASO 4 VERIFIQUE LOS REQUISITOS ELÉCTRICOS Y ADVERTENCIAS Los requisitos eléctricos para el lavavajillas son los siguientes: • En los Estados Unidos, instalar de conformidad con el Código Eléctrico Nacional/códigos estatales y municipales y/o códigos locales. • En Canadá, instalar de conformidad con el Código Eléctrico Canadiense C22.1-última edición/códigos provinciales y municipales y/o códigos locales. • Para conexiones directas de cable.
PASO 5 DESEMPACAR E INSPECCIONAR EL LAVAVAJILLAS Desempaque el lavavajillas en una zona libre de obstrucciones ya sea alrededor de la caja como en la parte superior. Recomendamos que conserve todos los materiales del empaque hasta que el lavavajillas esté completamente instalado y en funcionamiento para asegurarse de que haya retirado todas las piezas del producto de la caja antes de desecharla. 02 INSTALACIÓN DEL LAVAVAJILLAS Desempaque 1. 2. 3. 4.
instalación del lavavajillas Cañerías 1. Verifique la conexión de agua caliente en el lado izquierdo delantero de la base del lavavajillas. La placa de montaje debe estar asegurada a la parte delantera de la base, las roscas que se encuentran dentro de la conexión deben estar lisas y brillantes, y la zona debe estar limpia y libre de residuos. 2.
Correcto La abrazadera no está conectada correctamente. Ajuste la abrazadera en el centro. 02 INSTALACIÓN DEL LAVAVAJILLAS Incorrecto Para evitar daños en la manguera de desagüe, que está diseñada para cruzar el producto hacia la derecha, utilice el fijador de la manguera y el tornillo provistos para asegurar la zona central de la manguera en el producto. Asegúrelo en la zona marcada con la flecha.
instalación del lavavajillas PASO 7 COLOCACIÓN DEL LAVAVAJILLAS Y CONEXIÓN DEL CONDUCTO DEL SUMINISTRO DE AGUA CALIENTE 1. Regule las tres patas niveladoras en la parte inferior del lavavajillas después de medir la altura de la abertura del gabinete desde abajo de la encimera hasta el piso. (Ver el Paso 8, Nivelación del Lavavajillas.) 2. Ubique el conducto del agua caliente y el cable de alimentación. 3.
PASO 8 NIVELACIÓN DEL LAVAVAJILLAS 02 INSTALACIÓN DEL LAVAVAJILLAS 1. Abra la puerta y ubique el nivel contra la tina en el interior y verifique si el lavavajillas está nivelado. Si no está nivelado, rote las patas de nivelación en la parte inferior delantera del lavavajillas hasta que el lavavajillas esté nivelado. Vea la primera nota debajo de las instrucciones sobre el ajuste de la altura de las patas delanteras. 2.
instalación del lavavajillas PASO 9 FIJACIÓN DEL LAVAVAJILLAS El lavavajillas debe fijarse a la encimera o a las paredes laterales para mayor estabilidad y seguridad. 1. Si la encimera es de madera o si se trata de un material que no se daña al perforarlo, siga las instrucciones en 2-1 debajo. Si la encimera es de granito, mármol o cualquier otro material que pueda dañarse al perforarlo, siga las instrucciones en 2-2 debajo. 2-1.
02 INSTALACIÓN DEL LAVAVAJILLAS Tapa del SAMSUNG separador de la tina Atornillado a la pared lateral Tapa del separador de la tina Atornillado a la pared lateral PRECAUCIÓN Luego de instalar la lavavajillas en el gabinete, asegúrese de que la puerta se abra y se cierre libremente sin que interfiera el gabinete.
instalación del lavavajillas PASO 10 CONEXIÓN DE LA MANGUERA DE DESAGÜE 1. Verifique las piezas del fregadero a las cuales se conectará la manguera de desagüe. 2. Hay muchas maneras de insertar la manguera de desagüe en el conector de la manguera de desagüe del fregadero, como se muestra en las siguientes figuras. Debe conectar la salida del desagüe conforme a las reglamentaciones de instalación de tuberías de agua de su región. Caso 1.
PRECAUCIÓN Tenga cuidado al cortar el extremo de la manguera de desagüe ya que podría lastimarse. Limpie el área de conexión del desagüe del fregadero para evitar que la manguera se dañe. Verifique que no haya objetos extraños en la manguera de desagüe y quítelos. ¾ ⅝ pulgada 1 pulgada (25 mm) pulgada (16 mm) (19 mm) Si es necesario, corte el extremo de la manguera de desagüe por una de las líneas punteadas. Lavavajillas Fregadero Manguera de desagüe Mín.
instalación del lavavajillas PASO 11 CONEXIONES DEL CABLEADO 1. Antes de conectar el cable de alimentación al lavavajillas, asegúrese de desactivar el disyuntor. 2. En la caja de conexiones que se encuentra ubicada en la parte delantera derecha inferior del lavavajillas, busque los tres cables de alimentación del lavavajillas inclusive la conexión a tierra. 3. Pase el cable de alimentación al alivio de tensión, y luego dentro de la caja de conexiones (Figura 13). 4.
PASO 12 FINALIZACIÓN DE LA INSTALACIÓN Abra la puerta y quite todas las piezas innecesarias, goma espuma y empaque de papel. Active el disyuntor desactivado antes de comenzar la instalación. Abra la válvula del suministro de agua para suministrar agua al lavavajillas. Encienda el lavavajillas y luego seleccione y ejecute un ciclo. Verifique si el electrodoméstico se enciende correctamente o si hay alguna pérdida de agua mientras la lavavajillas está en funcionamiento.
especificaciones Suministro eléctrico 120 V, 15 A, 60 Hz AC Presión de agua 20 - 120 psi (140 - 830 kPa) Dimensiones (Ancho×Profundidad×Altura) 23⅞ x 25 x 33⅞ pulgada (605 x 636 x 860 mm) Temperatura mínima del agua en la entrada 120 ˚F (49 ˚C) Las especificaciones están sujetas a cambios sin previo aviso a los efectos de las mejoras de calidad. La apariencia real del lavavajillas puede diferir de las ilustraciones de este manual. 22_ especificaciones DW80H9950US-00151A-06_MES_150216.
notas DW80H9950US-00151A-06_MES_150216.
¿TIENE ALGUNA PREGUNTA O ALGÚN COMENTARIO? PAÍS LLAME AL O VISÍTENOS EN LÍNEA EN U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com/us/support CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca/support (English) www.samsung.com/ca_fr/support (French) Código Nro.: DD68-00151B-04_MES DW80H9950US-00151A-06_MES_150216.