Safety Data Sheets (SDSs) Safety Data Sheets (SDSs) Client Wuhan Lixing (Torch) Power Sources Co., Ltd. The Guandong Industrialized Country of East Lake High and New Add. of Client Technology Development Zone, Wuhan Description Lithium Manganese Dioxide Cylindrical Cell Model /Type CR2 Manufacturer Wuhan Lixing (Torch) Power Sources Co., Ltd. Add. of The Guandong Industrialized Country Of East Lake High and New Manufacturer Technology Development Zone, Wuhan Nominal Voltage 3.
Safety Data Sheets (SDSs) 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING Product Identifier Product name: Lithium Manganese Dioxide Cylindrical Cell Model: CR2 Other means of identification Synonyms:none Recommended use of the chemical and restrictions on use Recommended Use:Used in portabl electronic equipments; Uses advidsed against: a) Do not dismantle, open or shred batteries. b) Do not expose batteries to heat or fire. Avoid storage in direct sunlight.
Safety Data Sheets (SDSs) 2. HAZARDS IDENTIFICATION Classification No harm at the normal use.
Safety Data Sheets (SDSs) 3. COMPOSITION/INFORMATION ON INGREDIENTS Chemical characterixation: Mixtures Description: Product: Consisting of the following components. Common Chemical Name Concentration (%) CAS Number EC No. Lithium(Li) 3.6 7439-93-2 231-102-5 Manganese dioxide(MnO2) 31.0 1313-13-9 215-202-6 Graphite (C) 4.6 7782-42-5 231-955-3 Lithium Perchlorate 1.0 7791-03-9 232-237-2 Ethylene Glycol dimethylether(LiCIO4) 7.0 110-71-4 203-794-9 Propylene carbonate(C4H10O2) 8.
Safety Data Sheets (SDSs) 5. FIRE-FIGHTING MEASURES Suitable Extinguishing Media CO2, dry chemical powder, water spray. Unsuitable Extinguishing Media:No information available. Specific Hazards Arising from the Chemical Formation of toxic gases is possible during heating or in case of fire. In case of fire, the following can be released: Carbon monoxide(CO) Carbon dioxide Other irritating and toxic gases. Hazardous Combustion Products Carbon oxides.
Safety Data Sheets (SDSs) Methods for Cleaning up Use personal protective equipment. Dam up. Cover liquid spill with sand, earth or other Non combustible absorbent material. Pick up and transfer to properly labeled containers. Clean contaminated surface thoroughly. 7. HANDLING AND STORAGE Precautions for safe handling Handling Handle in accordance with good industrial hygiene and safety practice. Avoid contact with skin, eyes and clothing. Wear personal protective equipment. Wash thoroughly after handling.
Safety Data Sheets (SDSs) Individual protection measures, such as personal protective equipment Eye/Face Protection: Tightly sealed goggles Body protection: Protective work clothing. Skin protection: Protective gloves Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer.
Safety Data Sheets (SDSs) relative density: Not determined. Solubility in Water: Not determined. Solubility in other solvents Not determined. n-octanol/water partition coefficient Not determined. Auto-ignition temperature Product is not self-igniting. Decomposition temperature Not determined. Odout threshold Not determined. Evaporation rate Not determined. Viscosity Not determined. Other Information : Voltage 3.0V Electric capacity 850mAh Lithium content 0.25g 10.
Safety Data Sheets (SDSs) 12. Ecological Information Toxicity: Acquatic toxicity: No further relevant information available. Persistence and degradability: No further relevant information available. Bioaccumulative potential: No further relevant information available. Mobility in soil: No further relevant information available. Results of PBT and vPvB assessment PBT: Not applicable. vPvB: Not applicable. Other adverse effects: No information available. 13.
Safety Data Sheets (SDSs) The lithium ion batteries according to Section II of PACKING INSTRUCTION 968, or Section II of PACKING INSTRUCTION 969～970 of the Dangerous Goods regulations 57th Edition may be transported. The packaging shall be adequate to avoid mechanical damage during transport, handling and stacking. The materials and pack design shall be chosen so as to prevent the development of unintentional electrical conduction, corrosion of the terminals and ingress of moisture.
