High Resolution Dome Camera User Manual HCD-6010
High Resolution Dome Camera User Manual Copyright ©2019 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we'll introduce our model description.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. doing so may cause personal injury due to fire, electric shock, or falling objects. 8. If any unusual smells or smoke come from the unit, stop using the product. in such case, immediately disconnect the power source and contact the service center. continued use in such a condition may cause fire or electric shock. 9.
Safety information FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
important safety instructions Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
important safety instructions 17. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product. 18. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance.
contents 10 11 12 Features Components and Accessories Component names and functions Installation 13 14 16 Before Installation Installation Adjusting the monitoring direction for the camera connection 17 18 19 Connecting to Monitor Connecting to Power Using Coaxial Communications camera operation 21 21 Menu Configuration Menu Setup troubleshooting 34 Troubleshooting specifications 35 37 Specifications Dimension 10 13 17 21 34 35 English_9 ● Contents introduction
introduction Features yy High Resolution Use of a 2.1 mega pixel CMOS device provides clear pictures with a resolution of 1920x1080. yy Excellent Sensitivity - Color : 0.27Lux (F2.0, 1/30sec) B/W : 0.017Lux yy SSNR4 Function High performance DSP Chip removes noises of GAIN resulting from the low light level and shows a vivid, high definition video even in the dark place. yy Day&Night This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions.
Components and Accessories Check if the following items are included in the product package.
Introduction Component names and functions 1 Dome Cover 2 Rotate base : control rotating angle of camera. ➌ Lens Module ➍ Function Setup switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item. Switching between AHD and CVBS modes: Press the SET button for more than 5 seconds. ➎ Pan Base : Control panning angle of camera. ➏ Power Input Connector ➐ Video Output Jack : Video signals are output through this port.
Installation Before Installation yy Do not disassemble the camera on your own. yy Always be careful when you handle the camera. yy Do not hit the camera with your fist or shake it. Be careful not to damage the camera with careless maintenance or misoperation. yy Avoid installing the camera under direct influence of rain or high humidity. Do not operate it in a damp area. yy Use a clean, smooth, and dry cloth to wipe off a dirty area on the product surface.
Installation Installation Disassembling 1. Use one hand to hold the camera’s bottom part and turn the cover counterclockwise with another hand to separate it.
Installation ● Installation 1. Attach the installation template to the selected area and punch 2 holes as shown in the fi gure. 케이블 구멍 2. Use the 2 supplied screws to fi x the camera to the 2 punched holes. yy Set the mark imprinted on the camera to face the direction of camera monitoring. 3. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. 4. Join the dome cover to the camera body.
Adjusting the monitoring direction for the camera Pan Tilt Lens rotation `` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation. -- The effective range of pan is a total of 350 degrees. -- The effective range of rotation is a total of 355 degrees.
connection Connecting to Monitor Connect the Video OUT port on the rear panel of the camera to a AHD DVR. ● connection DVR Monitor yy As the connecting method varies with the instruments, refer to the manual supplied with the instrument. yy Only connect the cable when the power is turned off. MM `` T his product supports 4 video output formats of AHD, CVBS, TVI, and CVI. The default is AHD. Select the video output appropriate for your DVR.
Connection Connecting to Power You can connect power as shown in the following figure. 전원 입력 단자 When the resistance value of copper wire is at [20°C(68°F)] Copper wire size (AWG) #24 (0.22mm2) #22 (0.33mm2) #20 (0.52mm2) #18 (0.83mm2) Resistance value(Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 yy As shown in the table above, voltage decreases as the wire gets longer.
Using Coaxial Communications yy Coaxial Communications System yy OSD Control method DVR SET MENU/ENTER UP UP KEY DOWN DOWN KEY LEFT LEFT KEY RIGHT RIGHT KEY ● connection CAMERA BNC HCD-6010 English_19
Connection -- Video Cable The camera's video output port is connected to the DVR with a BNC coaxial cable, shown below. Distance 500m MM `` Recommended Cable Specification 5C2V I t is recommended that pure copper coax cable is used and not copper coated steel, as this will cause issues with the communication over the coaxial cable. `` To ensure picture quality, only single-channel video output connector can be used while camera connected to other video equipments.
camera operation Menu Configuration MAIN SETUP ◦ TVI ◦ CVI PROFILE ◦ BASIC ◦ ITS ◦ DAY/NIGHT ◦ INDOOR ◦ BACKLIGHT ◦ USER WHITE BAL ◦ ATW ◦ MANUAL ◦ INDOOR ◦ AWC → SET ◦ OUTDOOR EXPOSURE ◦ BRIGHTNESS ◦ AGC ◦ RETURN ◦ LENS ◦ SSNR4 ◦ SHUTTER ◦ SSDR BACKLIGHT ◦ OFF ◦ WDR ◦ USER BLC ◦ HLC SPECIAL ◦ DISPLAY ◦ DAY/NIGHT ◦ MOTION ◦ COAX ◦ DEFOG ◦ RETURN ◦ IMAGE ADJ ◦ PRIVACY EXIT ◦ SAVE ◦ NOT SAVE ◦ RESET ● Camera Operation VIDEO FORMAT ◦ AHD ◦ CVBS Menu Setup For function setting, you
Camera operation Select the function using the Function Setup switch. MAIN SETUP VIDEO FORMAT AHD PROFILE BASIC WHITE BAL ATW Change the status using the Function Setup switch. EXPOSURE BACKLIGHT OFF SPECIAL EXIT SAVE 1. Press the Function Setup switch. yy Main SETUP menu is displayed on the monitor screen. 2. Select a desired function using the Function Setup switch. yy Place the cursor over a desired item. 3. Set up a selected item by using the Function Setup switch. 4.
PROFILE MAIN SETUP VIDEO FORMAT AHD PROFILE BASIC 2. S elect a desired mode using the Function Setup switch according to the picture display you want. yy BASIC : T he most common environment is set to meet. WHITE BAL ATW EXPOSURE BACKLIGHT OFF SPECIAL EXIT SAVE yy DAY/NIGHT : I t will be set automatically so it optimizes to the day or night conditions, respectively.
Camera operation White Bal (White Balance) Use the White Balance function to adjust the screen color. 1. When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function Setup switch so that the arrow indicates ‘White Bal’ . 2. Select a desired mode using the Function Setup switch. MAIN SETUP VIDEO FORMAT AHD PROFILE BASIC WHITE BAL ATW Select one of the following 5 modes, as appropriate for your purpose.
EXPOSURE 1. W hen the SETUP menu screen is displayed, select ‘EXPOSURE’ by using the Function Setup switch so that the arrow indicates ‘EXPOSURE’. yy BRIGHTNESS : Adjusts the video brightness. sing this function, you can yy LENS : U control the screen brightness. EXPOSURE SETUP IIIIIIIIIIIIIIIIIIIII 50 BRIGHTNESS LENS MANUAL SHUTTER AGC HIGH SSNR4 ON SSDR OFF RETURN -- Manual : T he shutter does not automatically move but is fixed to the maximal degree in this mode.
Camera operation yy SSDR : SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas. -- ON : Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas. -- OFF : Turn off SSDR function.
DR yy W When there are both bright and dark areas at the same time, this mode makes both areas distinctive. WDR SETUP LEVEL RETURN MIDDLE ● Camera Operation -- L EVEL : S elect one from low, middle, high to adjust the brightness of the WDR setup. -- RETURN : Return to the MAIN SETUP menu. MM ```` If the white balance menu is set to manual, then HLC performance can be limited.
Camera operation SPECIAL 1. W hen the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup switch so that the arrow indicates ‘SPECIAL’. 2. Select a desired mode using the Function Setup switch. yy DISPLAY ➊ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘DISPLAY’. ➋ S elect a desired mode using the Function Setup switch.
-- FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue) -- LANGUAGE : You can select the menu language according to your requirements. -- RETURN : Return to the SPECIAL menu. yy IMAGE ADJ ❶ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘IMAGE ADJ’. ❷ Select a desired mode using the Function Setup switch. -- GAMMA : The setting range is 0.35 ~ 1.0. The closer to 1.0 the setting is, the darker it gets.
Camera operation yy DAY/NIGHT: You can display pictures in color or in black and white. ➊ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘DAY/NIGHT’. ➋ Select a desired mode using the Function Setup switch according to the picture display you want. -- AUTO : The mode is switched AUTO SETUP to ’Color‘ in a normal ON ▶ BURST MODE environment, but switches DURATION NORMAL to ’B/W‘ mode when DWELL TIME 30 SEC ambient illumination is low.
yy DEFOG : You can use the defog mode to allow the camera to automatically detect the fog density of the screen and display a clear image despite smog, fog or general poor visibility. ➊ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘DEFOG’. DEFOG ▶ LEVEL RETURN MIDDLE -- Manual : Depending on the defog level set by the user, adjust the clarity of image.
Camera operation yy MOTION : This product generates signals each time an object movement is detected in the 4 areas of the screen so efficient monitoring can be achieved. ➊ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘MOTION’. MOTION DET ▶ DET. AREA ALARM OUT SENSITIVITY RETURN I IIIIIIIIII IIIIIIIIII 5 ➋ S elect a desired mode using the Function Setup switch. yy DET. AREA : Set the areas of DETECT AREA motion detection.
EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose. yy NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu. yy RESET : R evert camera to factory settings. (The language settings will remain the same) MM `` To turn off the power after setting the camera menu, the OSD menu must disappear first. English_33 ● Camera Operation yy SAVE : Save the current settings and exit the MAIN SETUP menu.
troubleshooting Troubleshooting If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. Problems Troubleshooting Nothing appears on the screen. yy Check that the power cord and line connection between the camera and monitor are properly connected. yy Check that you have properly connected BNC cable to the camera. The image on the screen is dim.
specifications Specifications HCD-6010 Video 1/2.8” 2M CMOS Total Pixels 1,945(H) x 1,109(V) 2.16M pixels Effective Pixels 1,945(H) x 1,097(V) 2.13M pixels Scanning System Progressive Scan Min. Illumination Color : 0.27Lux (F2.0, 1/30sec) B/W : 0.
Specifications HCD-6010 Privacy Masking Off / On (8 zones rectangle) Gain Control Off / Low / Middle / High / Very High White Balance ATW / Outdoor / Indoor(4,500K° ~ 8,500K°) / Manual / AWC (1,800K° ~ 10,500K°) Electronic Shutter Speed 1 sec ~ 1/12,000 sec Reverse Off / H-Rev / V-Rev / HV-Rev Profile Basic, Day & Night, Backlight, ITS, Indoor, User Remote control interface Coaxial Protocol AHD : ACP (AHD Coax Protocol), CVBS : Pelco-C (Coaxitron) CCP (CVI Coax Protocol), TCP (TVI Coax Protoc
Dimension Unit: mm (inch) ● specifications English_37
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwha-security.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.