High Resolution Camera User Manual HCD-7010R/7020R/7030R HCV-7010R/7020R/7030R HCO-7010R/7020R/7030R
High Resolution Camera User Manual Copyright ©2017 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we'll introduce our model description.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. doing so may cause personal injury due to fire, electric shock, or falling objects. 8. If any unusual smells or smoke come from the unit, stop using the product. in such case, immediately disconnect the power source and contact the service center. continued use in such a condition may cause fire or electric shock. 9.
safety information FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
important safety instructions Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
important safety instructions 17. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product. 18. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance.
contents 10 11 14 Features Components and Accessories Component names and functions Installation 17 17 22 Before installation Installation Adjusting the monitoring direction for the camera connection 24 25 27 Connecting to Monitor Connecting to Power Using Coaxial Communications camera operation 29 29 Menu Configuration Menu Setup troubleshooting 40 Troubleshooting specifications 41 Specifications (HCD-7010R/7020R/7030R) Specifications (HCv-7010R/7020R/7030R) Specifications (HCO-7010R/7020R/
introduction Features yy High Resolution Use of a 4.1 mega pixel CMOS device provides clear pictures with a resolution of 2560x1440. yy Excellent Sensitivity - HCD-7010R/HCV-7010R/HCO-7010R Color : 0.26Lux (F1.8, 1/30sec) B/W : 0Lux(IR LED on) - HCD-7020R/HCV-7020R/HCO-7020R HCD-7030R/HCV-7030R/HCO-7030R Color : 0.27Lux (F2.
Components and Accessories Check if the following items are included in the product package.
introduction Camera Quick Manual Template Tapping Screw Machine Screws L Wrench Card-type moisture absorbent Video Output Cable 12_ introduction
● introduction Camera Quick Manual Screws Template Wrench Card-type moisture absorbent Video Output Cable English_13
introduction Component names and functions HCD-7010R/7020R/7030R 9 3 ❿ 2 1 5 4 6 8 7 1 Dome Cover 2 Shield Case 3 Rotate base : control rotating angle of camera. 4 Vari-focal Lens Module : HCD-7010R : 2.8mm(F1.8) HCD-7020R : 4.0mm(F2.0) HCD-7030R : 6.0mm(F2.0) 5 Function Setup switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item. Switching between AHD and CVBS modes: Press the SET button for more than 5 seconds.
HCV-7010R/7020R/7030R 3 ❿ 2 5 4 8 6 7 1 Dome Cover 2 Rotate base : control rotating angle of camera. 3 Vari-focal Lens Module : HCV-7010R : 2.8mm(F1.8) HCV-7020R : 4.0mm(F2.0) HCV-7030R : 6.0mm(F2.0) 4 Function Setup switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item. Switching between AHD and CVBS modes: Press the SET button for more than 5 seconds.
introduction HCO-7070R 1 2 4 5 3 6 CAUTION: Be ware of the Rated Voltage and Polarity of the power connection. 7 1 Camera Sunshield 2 Knob Sunshield : Fixing the sunshield onto the camera. 3 Front cover 4 Function Setup Switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item. Switching between AHD and CVBS modes: Press the SET button for more than 5 seconds.
Installation Before installation Installation Disassembling(HCD-7010R/7020R/7030R) 1. Use one hand to hold the camera’s bottom part and turn the cover counterclockwise with another hand to separate it. 2. Lift up the shield case to separate it. Shield Case English_17 ● Installation Ensure you read out the following instructions before installing the camera: yy You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.
Installation Disassembling(HCV-7010R/-7020R/-7030R) Using the L-wrench provided, loosen 3 screws by turning them counterclockwise and separate the dome cover.
Installation(HCD-7010R/7020R/7030R) ● Installation 1. Attach the installation template to the selected area and punch 2 holes as shown in the fi gure. 케이블 구멍 2. Use the 2 supplied screws to fix the camera to the 2 punched holes. yy Set the mark imprinted on the camera to face the direction of camera monitoring. 3. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. 4.
Installation Installing the camera on a ceiling or wall(HCV-7010R/-7020R/-7030R) 1. Drill holes on the ceiling by matching to the holes on the case bed, and insert plastic anchors (HUD 5) (not included) fully into the holes. Fix the case bed on the ceiling by using screws . (3 places) screw 2. Connect Power and video cables and arrange them through the hole you want to pass when mounting the main body on the mounting bracket, note that not to damage or squeeze the cables.
3. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera”section. 4. Close the dome cover. ● Installation `` To ensure waterproofing, tight up the fixing bolts using the L-wrench. Dome Cover L Wrench MM `` The installation should be done by qualified service personnel or system installers. `` If the ceiling material is not strong enough to hold the installation screws, the camera may fall off. Reinforce the ceiling as needed.
Installation Adjusting the monitoring direction for the camera Pan Tilt Lens rotation Pan Tilt 22_ Installation Lens rotation
-- The effective range of rotation is a total of 355 degrees. -- The effective range of tilt is a total of 67 degrees. `` Methods of adjustment 1. After installing the camera, adjust the panning angle in consideration of the monitoring direction. 2. Adjust the view angle and focus for the video. - For convenience of operation, adjust the rotation part to fix the lever. 3. Set the horizontal angle so that the image is not reversed. 4.
connection Connecting to Monitor Connect the Video OUT port on the rear panel of the camera to a AHD DVR.
HCV-7010R/7020R/7030R REC HDD ALARM NETWORK BACKUP POWER Rated Voltage and Polarity of the power connection. CAUTION: Be ware of the ● connection AHD DVR Monitor yy As the connecting method varies with the instruments, refer to the manual supplied with the instrument. yy Only connect the cable when the power is turned off. MM `` T his product supports 4 video output formats of AHD, CVBS. The default is AHD. Select the video output appropriate for your DVR.
connection Power Input Terminal REC HDD ALARM NETWORK BACKUP POWER HCV-7010R/7020R/7030R HCO-7010R/7020R/7030R Rated Voltage and Polarity of the power connection. Power Input Terminal CAUTION: Be ware of the When the resistance value of copper wire is at [20°C(68°F)] Copper wire size (AWG) #24 (0.22mm2) #22 (0.33mm2) #20 (0.52mm2) #18 (0.83mm2) Resistance value(Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.
Using Coaxial Communications yy Coaxial Communications System yy OSD Control method DVR SET MENU/ENTER UP UP KEY DOWN DOWN KEY LEFT LEFT KEY RIGHT RIGHT KEY : BNC ● connection ● CAMERA HCD-7010R/7020R/7030R HCV-7010R/7020R/7030R HCO-7010R/7020R/7030R English_27
connection -- Video Cable The camera's video output port is connected to the DVR with a BNC coaxial cable, shown below. Distance 500m MM `` Recommended Cable Specification 5C2V I t is recommended that pure copper coax cable is used and not copper coated steel, as this will cause issues with the communication over the coaxial cable. `` To ensure picture quality, only single-channel video output connector can be used while camera connected to other video equipments.
camera operation Menu Configuration MAIN SETUP ◦ AHD ◦ CVBS D-WDR ◦ OFF ◦ ON WHITE BAL ◦ ATW ◦ MANUAL ◦ INDOOR ◦ AWC → SET ◦ OUTDOOR EXPOSURE ◦ BRIGHTNESS ◦ DNR ◦ SHUTTER ◦ RETURN ◦ AGC BACKLIGHT ◦ OFF ◦ USER BLC ◦ HLC SPECIAL ◦ DISPLAY ◦ DAY/NIGHT ◦ RETURN ◦ COAX ◦ PRIVACY ◦ IMAGE ADJ ◦ MOTION EXIT ◦ SAVE ◦ NOT SAVE ◦ RESET ● Camera Operation VIDEO FORMAT Menu Setup For function setting, you can use the function setting switch inside the cover.
camera operation Select the function using the Function Setup switch. MAIN SETUP 1. VIDEO FORMAT AHD 2. D-WDR OFF 3. WHITE BAL ATW Change the status using the Function Setup switch. 4. EXPOSURE 5. BACKLIGHT OFF 6. SPECIAL 7. EXIT SAVE 1. Press the Function Setup switch. yy Main SETUP menu is displayed on the monitor screen. 2. Select a desired function using the Function Setup switch. yy Place the cursor over a desired item. 3. Set up a selected item by using the Function Setup switch. 4.
D-WDR If an object has a large variance between bright and dark areas, it will keep bright areas bright and make selected dark areas bright, so that the overall brightness can be maintained. 2. U se the Function Setup switch to change the D-WDR level in the sub menu according to the contrast between bright and dark areas. MAIN SETUP 1. VIDEO FORMAT 2. D-WDR 3. WHITE BAL OFF ATW 4. EXPOSURE 5. BACKLIGHT OFF 6. SPECIAL 7.
camera operation yy INDOOR : Select this when the color temperature is between 4,500K and 8,500K. Automatically adjusts the camera color for optimization to the indoor environment. yy MANUAL : S elect this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that button to MANUAL mode, fine-tune the White Balance and the Function Setup switch. WB MANUAL IIIIIIIIIIIIIIIIIIIII 147 1. RED GAIN IIIIIIIIIIIIIIIIIIIII 124 2. BLUE GAIN 3.
greater the shutter value the brighter the screen is but the more the residual MM `` The images of objects there are. `` If the min shutter value is large, it can cause noise, spots and white areas but still operate normally. ● Camera Operation `` If you do not use the AGC mode on the exposure menu, it cannot be set above 1/60sec. `` Depending on the setting range of the minimal/maximal shutter, the screen exposure can become saturated.
camera operation LC (High Light Compensation) : yy H This function masks the strong light to minimize white out due to over exposure and preserve much of the on-screen details when the camera aims a strong light source. -- LEVEL : Adjusts the brightness level of a monitoring area. -- LIMIT : Enable to change the operating condition. -- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced. -- RETURN : Return to the MAIN SETUP menu. MM ```` HLC SETUP ▶ 1. LEVEL 2. LIMIT 3. TOP 4.
SPECIAL 2. Select a desired mode using the Function Setup switch. MAIN SETUP 1. VIDEO FORMAT AHD 2. D-WDR OFF 3. WHITE BAL ATW 4. EXPOSURE 5. BACKLIGHT yy DISPLAY 6. SPECIAL ➊ If the SPECIAL menu screen is displayed, 7. EXIT use the Function Setup switch so that the arrow indicates ‘DISPLAY’. ➋ S elect a desired mode using the Function Setup switch. OFF SAVE -- FONT COLOR : You can change the OSD font color.
camera operation -- SHARPNESS : S elect a mode to adjust the thickness of an image’s sharpness. Increase or decrease the level of each mode to adjust the level of sharpness. yy OFF : Released state yy ON : The setting range is 1 ~ 32. -- RETURN : Return to the SPECIAL menu. MM `` When the V-REV or H-REV mode is enabled, the text on the screen does not flip. `` If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear.
-- COLOR : The picture is always displayed in color. -- B/W : T he picture is always displayed in black and white. You can turn on or off the burst signal on B/W mode. yy PRIVACY: Mask an area you want to hide on the screen. ➊ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘PRIVACY’. ➋ S elect a desired mode using the Function Setup switch. -- AREA : Y ou can select up to 8 PRIVACY areas. PRIVACY AREA AREA1 ▶ 1. AREA 2. MODE OFF 3.
camera operation `` MASK : Under Motion Detection, If you don’t want to see mosaic image on the screen, you may turn MASK OFF. If you wants to see mosaic image, please turn it on. `` TRANSPARENCY: Adds or removes transparency from the masking area. `` TOP/BOTTOM/LEFT/RIGHT : Area location can be adjusted. `` RETURN : Return to the MOTION DET menu. yy SENSITIVITY : S et the sensitivity of the motion detection. When you adjust the higher level, the more sensitive.
EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose. yy SAVE : Save the current settings and exit the MAIN SETUP menu. yy RESET : Revert camera to factory settings. (The language, communication and lens settings will remain the same). English_39 ● Camera Operation yy NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
troubleshooting Troubleshooting If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. Problems Troubleshooting Nothing appears on the screen. yy Check that the power cord and line connection between the camera and monitor are properly connected. yy Check that you have properly connected BNC cable to the camera. yy Check the type of lens. The image on the screen is dim.
specifications Specifications (HCD-7010R/7020R/7030R) HCD-7010RN/ HCD-7010RP HCD-7020RN/ HCD-7020RP HCD-7030RN/ HCD-7030RP Video 1/3” 4M CMOS Total Pixels 2720(H) x 1536(V) Effective Pixels 2688(H) x 1520(V) Scanning System Progressive Scan Min. Illumination Color : 0.26Lux (F1.8, 1/30sec) Color : 0.27Lux (F2.0, 1/30sec) Color : 0.27Lux (F2.
specifications HCD-7010RN/ HCD-7010RP HCD-7020RN/ HCD-7020RP HCD-7030RN/ HCD-7030RP White Balance ATW / Outdoor / Indoor(4,500K° ~ 8,500K°) / Manual / AWC (1,800K° ~ 10,500K°) Electronic Shutter Speed 1/30 sec ~ 1/12,000 sec(N), 1/25sec~ 1/12,000sec(P) Reverse Off / H-Rev / V-Rev Remote control interface Coaxial Protocol AHD : ACP (AHD Coax Protocol), CVBS : Pelco-C (Coaxitron) IR Distance 20m(65.62ft) Video Transmission Distance 500m(5C2V) 25m (82.02ft) 30m (98.
Specifications (HCv-7010R/7020R/7030R) HCV-7010RN/ HCV-7010RP HCV-7020RN/ HCV-7020RP HCV-7030RN/ HCV-7030RP Video 1/3” 4M CMOS Total Pixels 2720(H) x 1536(V) Effective Pixels 2688(H) x 1520(V) Scanning System Progressive Scan Min. Illumination Color : 0.26Lux (F1.8, 1/30sec) Color : 0.27Lux (F2.0, 1/30sec) Color : 0.27Lux (F2.
specifications HCV-7010RN/ HCV-7010RP HCV-7020RN/ HCV-7020RP HCV-7030RN/ HCV-7030RP White Balance ATW / Outdoor / Indoor(4,500K° ~ 8,500K°) / Manual / AWC (1,800K° ~ 10,500K°) Electronic Shutter Speed 1/30 sec ~ 1/12,000 sec(N), 1/25sec~ 1/12,000sec(P) Reverse Off / H-Rev / V-Rev Remote control interface Coaxial Protocol AHD : ACP (AHD Coax Protocol), CVBS : Pelco-C (Coaxitron) IR Distance 20m(65.62ft) Video Transmission Distance 500m(5C2V) 25(82.02ft) 30m(98.
Specifications (HCO-7010R/7020R/7030R) HCO-7010RN/ HCO-7010RP HCO-7020RN/ HCO-7020RP HCO-7030RN/ HCO-7030RP Video 1/3” 4M CMOS Total Pixels 2720(H) x 1536(V) Effective Pixels 2688(H) x 1520(V) Scanning System Progressive Scan Min. Illumination Color : 0.26Lux (F1.8, 1/30sec) Color : 0.27Lux (F2.0, 1/30sec) Color : 0.27Lux (F2.
specifications HCO-7010RN/ HCO-7010RP HCO-7020RN/ HCO-7020RP HCO-7030RN/ HCO-7030RP Reverse Off / H-Rev / V-Rev Remote control interface Coaxial Protocol AHD : ACP (AHD Coax Protocol), CVBS : Pelco-C (Coaxitron) IR Distance 20m(65.62ft) Video Transmission Distance 500m(5C2V) 25(82.02ft) 30m(98.
Dimension Unit: mm (inch) ● specifications English_47
48_ specifications Unit: mm (inch)
Unit: mm (inch) ● specifications English_49
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwha-security.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.