DIGITAL VIDEO RECORDER User Manual HRX Series
Digital Video Recorder User Manual Copyright ©2021 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview Important Safety Instructions Standards Approvals Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
overview CAUTION ● RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. ● Do not ingest battery, Chemical Burn Hazard. ● This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. ● Keep new and used batteries away from children.
Contents overview Important Safety Instructions 23 3 Product User Manual Description 23 Check Event List 3 Target Audience 24 Event Search 3 How to Use the Product 24 Event Instant Viewer 5 Contents 24 Stop Alarm Output 25 getting started 9 live 13 Real-Time Event Monitoring Camera Video Control Starting the system 25 Capture 9 installation Wizard 25 Instant Viewer 12 Shutting down the System 25 Temperature Detection Mode 12 Restarting the System 26 PTZ Mode 12 Logi
overview play 35 35 Screen Layout of the Play 36 Play Search Results 37 setup 38 58 IP & Port Time Line Adjustment 60 DDNS 36 Open Time Line Channel 61 IP Filtering 36 Play Button Name and Function 61 HTTPS 62 802.
9 Add Layout and Set Name 79 Change of Layout Channel and Name 79 Delete Layout Real-Time Event Monitoring 80 Event Type and Camera Settings 80 Check Event List 81 Event Instant Viewer 81 Stop Alarm Output Live Screen Menu 82 Camera Video Control 85 86 Check Layout List 79 81 84 search viewer 79 82 Capture 82 PC Recording 82 Instant Viewer 82 Microphone Output 82 PTZ Mode 83 Zoom In 83 Audio 83 Image Rotation 83 Channel Aspect Ratio PTZ Control 84 PTZ Control Men
overview 101 Setting the System 101 Date/Time/Language 102 User 102 System Management 103 Log export viewer 104 appendix 106 8_ overview 104 SEC Backup Viewer 104 Recommended System Requirements 104 Screen Layout of the Backup Viewer 106 Use Joystick 106 Using Virtual Keyboard 107 Troubleshooting
getting started Starting the system installation Wizard 1. Connect the power cable of the recorder to the wall outlet. As shown below, proceed through each step of the . Install Wizard can only be accessed at factory reset. If you do not want to proceed, click . 2. You will see the initialization screen. The initialization process will last about 2 minute. If a new HDD is installed, the initialization process may take longer. 1.
getting started Setting up the network The network port can be used as a common port for camera and web viewer connection. Click of the network connected to the recorder. ●● IP type : Allows you to select the type of network access. ●● IP Address, Subnet Mask, Gateway, DNS 4. Set the camera password in factory reset on the screen. If ID/PW is already set in the camera, register the ID/PW and click .
6. To set the recommended resolution on the screen, click followed by the button. 8. On the screen, you can view the camera videos registered to each channel in thumbnails along with thumbnail information. To change the camera video position, select a video and drag and drop it to the desired location. • getting started 7. On the screen, select a camera to register from the searched camera list and click .
getting started Shutting down the System Login 1. Select at the top right of the screen. To use the Recorder menu, you are required to login as a user that is authorized to access the applicable menu. 2. The window will appear. 1. Select at the top right of the screen. 3. Click on . 2. The window will appear. The system will shut down. Restarting the System 1. Select at the top right of the screen. 2. The window will appear. 3.
live Shows the video of the camera connected to the recorder. Also, you can adjust the camera and check the network transfer status. Item Description Displays information of the OSD screen on the video window. Screen Layout of the Live Shows channel information. The live screen is built as follows. • live Shows the status of all cameras connected to the recorder. Moves the page of the split mode. Moves to the next page of the split mode according to the set time.
live Checking the System Status Item The icon at the top of the screen indicates the status of the system. Description Displayed when manually recording a video while the access restriction for stop recording is enabled. Only a user with the permission to stop recording is allowed to stop recording. Displayed when exporting a recorded video in live mode. Displayed when there is software to update on the camera. Displayed when playing the layout sequence.
Check Camera List Live Screen Menu Displays the camera type, status, and name registered in the recorder. After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen menu. The live screen menu appears differently depending on the recorder operation status or the type of the registered camera. Itrem Channel information • live ￭￭ Each function may be restricted depending on the type of camera and the user's authority.
live Icons on the Live Screen Item You can check the status or operation with the icons on the live screen. Description Events from the recorder and camera are displayed in icons. ￭￭ The icons displayed on the screen may differ depending on the type of camera and the user's authority. Event Display For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of Contents. It is displayed on the channels that can enable the PTZ mode. Displays AUDIO ON/OFF.
￭￭ Each product may support different split view modes. Live Screen Mode You can display your camera's live video in various split modes. ￭ If the analog camera has been automatically registered, it is displayed using the camera resolution.
live Switching the Split Mode Manual Switching You can split the live video from cameras to Single, 4-split, 9-Split, or 16-split mode and watch them one by one. Click or at the bottom of the screen or enter a page number to go to that page. ￭￭ Each product supports different split modes. Auto Sequence To switch the screen automatically, click < > at the bottom of the screen. You can monitor the split mode of your own choice by switching one after another at a certain interval.
Channel Information Display Check the Camera Status You can check the information of the video being recorded with each camera. You can check the status of all cameras connected to the recorder. To check the channel information, click < To check the camera status, click < > at the bottom of the screen. > at the bottom of the screen. • live The information of the current video is displayed on the live video which is being monitored. Live Status 800x448 (H.
CH7 CH8 CH3 CH9 CH4 CH3 CH6 CH4 CH8 CH8 CH10 CH13 CH7 CH1 CH1 CH5 CH6 live CH2 CH3 CH4 CH6 34 78 CH8 CH2 CH1 CH1 CH11 CH12 CH1CH2 CH4 CH3 15 16 CH16 CH7 CH7CH8 CH8CH9 CH2 CH3 CH1 CH7 CH2 CH2 CH8 CH2 CH3 CH9 CH3 CH4 CH3 CH9 CH3 CH10 3 CH3 CH6 CH6 4 CH4 CH8 CH8 CH13 CH16 CH4 CH5 CH1 CH10 CH11 CH11 CH12 5 ●● CH4 CH11 CH12 CH2 CH14 CH15 CH3 CH5 CH6 CH2 CH2 CH2 CH4 CH8 CH1 CH4 CH1 CH9 CH4CH5 CH3 CH3 CH3 CH5CH6 CH4 CH6 CH7 CH1 CH9 CH9 CH
Changing Overall Channel Aspect Ratio Full Screen Mode Video screen ratio for all channels can be changed in live split screen mode. You can change to full screen mode, which has no top/bottom/left/right areas of the live screen. Click < > at the bottom of the screen. It changes to the actual proportion of the video. Click < Click < > to return to the previous aspect ratio. Changes to full screen mode. > at the bottom of the screen.
live Setting Up the Live Layout Change of Layout Channel and Name This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a single layout. 1. Click < Example) Layout "Lobby" - Lobby camera 1, Lobby camera 2, Front entrance camera 2 Layout "VIP" - Directors' meeting room 1, Directors' meeting room 2, Directors' lounge 1, Corridor camera on the 7th floor List > at the top left of the live screen, and then click < 2.
Play Layout Sequence Real-Time Event Monitoring Click < Play sequence> at the bottom of the layout list to automatically switch the layout according to the sequence settings. Real-time events that occurred on the camera can be checked in the live video window and event list. Check Event List Click < Event> on the left side of the live screen to display the real-time event list. • live ￭￭ When new events occur, the list of events will be updated accordingly.
live Event Search Event Instant Viewer You can browse events by camera and event type. To search for a specific event, click < > to select the event type and camera to browse. Event filter Select an event to check from the event list, and click < occurred. > to play the recorded video at the time the event ￭￭ Instant viewer can play an event video for 1 minute. Common event Displays only selected events in the event list.
Camera Video Control Instant Viewer By using the function icon of the video window, you can easily use the functions of capture, video zoom, PTZ camera and thermal imaging camera. When you place your mouse over the video window, the live screen menu will appear. You can move the video back 30 seconds and play it while live monitoring. Instant viewer plays video from 30 seconds to 1 minute from the current time. Select the desired channel and click < The Instant Viewer screen appears. >.
live PTZ Mode Zoom In You can run PTZ control of the selected channel. You can zoom in or out the video via digital zoom. Select the desired channel and click < Select the desired channel and click < >. Enters the PTZ control mode. Enters the digital zoom mode. ￭￭ Depending on the camera, the PTZ control function and speed may be different. ●● ●● : The PTZ mode is closed. : After clicking the digital zoom icon, you can use < ●● : Returns to the 1x zoom screen.
Display Text Change Channel Aspect Ratio You can monitor texts regarding the sales record received from POS in real time. You can change the aspect ratio of each channel. ￭￭ This is executable when a text device is connected. ￭￭ The Recorder can display text on a live screen when a text device is set. For details, refer to the "Setup > Setting the Device > Text" page in Select the desired channel and click < >. It changes to the actual proportion of the video. the Table of Contents.
live PTZ Control Item With this Recorder, you can configure the settings of a PTZ camera as well as commercial cameras in the market to your preference. Description Zoom out/Zoom in This is active only if a channel that a PTZ camera is connected to is selected. Getting Started with PTZ Operations The PTZ camera will be activated only if the channel of the PTZ camera is selected. After selecting the desired channel, click < > on the live screen menu.
Using Digital PTZ (D-PTZ) Function To delete a registered preset 1. Register a camera that supports the D-PTZ profile. 1. Click < >. 2. Click < >. window will appear. ￭￭ In cameras that support the D-PTZ profile, you can use the D-PTZ function. 2. Both cameras that support general PTZ and cameras that support D-PTZ can control the live image using some of the function menus.
live Exporting the Recorded Video You can search the storage device to be exported and export the recorded video of the desired time by layout or channel. 1. Click < > at the bottom of the screen. 2. The export setup screen will appear. ●● ●● ●● Select a layout : Select a desired layout from the layout list. Channel : Select a channel to export. ￭￭ You can select multiple channels. If you select , all channels will be selected.
search You can search recorded video by various conditions such as time, event, and export. Time Search Screen Layout of the Search You can search the recorded data by the desired date and time conditions. ￭ The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently depending on whether the data time zone recorded at the same time and daylight saving time (DST) is applied. • search 1. Select
search Event Search Text Search You can search for various events by channel. You can search the data input to the POS device connected to the recorder. 1. Select in the menu. 1. Select in the menu. 2. Select a channel to search. 2. Select a date and time to search. ￭ If you select a channel to search, you can change the channel display mode by clicking < >. You can select a desired channel by clicking or dragging it 3. Set the keyword item.
Export Search ARB Search You can search the exported data on the connected storage device. Only data saved in recorder file format when exported will be retrieved. You can search auto-recovery backup data stored on ARB storage devices. • search 1. Select in the menu. 1. Select in the menu. 2. When you click
search Bookmark Search Smart Search You can search for bookmarked data. You can search for events by selecting a region of interest, an exclusive region, or a virtual line from a recorded video at a specific time. ￭ To use smart search, you need to set the area of the camera's “Motion Detection" or “IVA” to the entire area. However, if you want to search for cameras after Wisenet X series, you must select “Enable" in "Event setup > IVA” of the camera.
play You can play the recorded data and export the video you want during playback. Screen Layout of the Play Item Show/Hide Channel Split mode You can change the number of channels displayed in the time line. ￭ Up to 4 channels of time line can be displayed. You can select the split mode. Deletes all camera video tiles from the video window. Full aspect ratio Change the video display ratio.
play Play Search Results Time Line Adjustment Play Button Name and Function Paused state You can move the playback position and zoom the time line in and out. ● ● ● Click the desired play position in the time line. The playback start position will be moved. ￭ Click the start point on the left side of the time line to move the playback position to the start point of the first video. ￭ Place your mouse over the time line to see the corresponding thumbnail of the recorded video.
Search Results Export You can export the search results to a file. 1. Click the < > button. 2. Select a layout and channel to export. • play 3. Select a start date/time and an end date/time. ￭ If you changed the time zone of the recorder, select whether to apply DST. 4. Select the overlap. It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected time. 5. Click < > to select a storage device. 6. Please select a storage file type.
setup Sets the camera, recording, event, device, network, and system environment. Setting the Camera Screen Layout of the Setup You can access to the channel setup, camera settings, and profiles and camera password-related settings. Setting the Channel You can register and connect the cameras per channel. Setup > Camera > Channel setup ● Item Menu Top menu list Description Click each menu to go to the menu screen. Configure the settings or select a parent item to change the existing settings.
Automatic Registration of Network Cameras 1. Click in the field. 1. In the field, click on the button. 2. Search for an analog camera connected. 2. window appears. • setup Setting the Analog Camera 3. Select the desired item and change the setting. ● Apply to other ports : If you select , the "Apply to other ports" confirmation window will appear.
setup Registering a Network Camera Manually ● Address type : Select an address type of the camera. ￭ The supported address type may differ depending on the type of the connected product. – IPv4/IPv6 : Used to provide the IP address of the camera manually. – Wisenet DDNS : This is available only if the camera is registered with the Wisenet DDNS(ddns. hanwhasecurity.com) server. Provide the registered domain for DDNS ID. Example) http ://ddns.hanwha-security.
If you want to check the error details of camera registration Network Camera Firmware Upgrade If you failed to register a camera, the reason for the failure will be displayed. Connection failed due to unknown error. : This message appears if the camera has failed to be registered due to unknown connection status. ● Due to the camera account locking, access has failed. : When you enter a wrong ID/password 5 times to login to the camera account, this message is displayed.
setup Setting the Camera Functions You can set the camera while viewing the live video of the selected camera. Setup > Camera > Camera setup ● SSNR : Adjusts the brightness by reducing noise and minimizing afterimages even in dark places. ● Sens-up : Automatically adjusts the shutter speed according to the brightness of the current light. ● IRIS/Lens : Adjusts the brightness by automatically or manually adjusting the camera IRIS and lens.
Setting the Profiles Setting the Live Profile You can change the live setup for the camera. Setting the Recording Profile Setup > Camera > Profile setup > Live You can set the video profile where the recording will be played for the camera connected to each channel. • setup Setup > Camera > Profile setup > Record ● ￭ You can configure the settings only for the profiles that are supported by the camera.
setup Setting the Remote Profile Editing the Profiles You can set the video profile transmitted to the network. You can change the video setting for the camera registered for each channel. Setup > Camera > Profile setup > Remote Setup > Camera > Profile setup : Displays the camera of the corresponding channel as a list or a thumbnail. ● ● Camera name : Display the camera name. ● IP & Port : Displays the IP or port location of the camera.
Dewarping Setup How to set WiseStream Press the button at the bottom of the window to go to the distortion correction setup popup window for each channel. Function to analyze the complexity of the video and effectively reduce the data size while maintaining the quality. For details, refer to the camera's help or the product's user guide.
setup Dynamic GOV/FPS setup Setting Camera Password Dynamic GOV can be used to automatically change the length of GOV depending on the video condition. For details, refer to the camera's help or the product's user guide. You can change the passwords of all registered cameras at once. At the bottom of the screen, press the button to open the dynamic GOV/FPS setup popup for the channel. You can register the camera’s ID and password.
Setting the Recording Record Setup You can setup scheduled recording, event recording and other recording related settings. You can set the resolution and number of recordings for each channel when an event occurs or during a normal recording. You can check frame rates and data transfer amount of Full Frame and Key Frame recordings for each channel, and set the transfer limit for recordings.
setup ￭ If a channel's data transfer exceeds defined allowed limit, then it may affect to other channels, and may force switching to recording even when the channel is configured to recording mode. For Key Frame recording channels, the icon for limited recording appears on the live screen's top side. But if the sum of the limits is below the max limit, you can still receive the entire frames despite exceeding the permitted bitrates for each channel.
Object Motion Setup > Event > Event setup > Object Setup > Event > Event setup > Motion Network camera Analog camera • setup ● Object detection : You can set whether to enable object detection. ● Object type : You can select the object type to detect. ● ● ● ● ￭ Object items may vary depending on the camera model. ● Motion detection : You can set whether to enable motion detection. ● MD type : You can set a detection area and a detection excluded area.
setup IVA Tampering Setup > Event > Event setup > IVA Setup > Event > Event setup > Tampering ● IVA : You can set whether to enable intelligent video analytics. ● Tampering detection : You can set whether to enable tampering detection. ● Type : You can set a virtual line, virtual area, and detection excluded area. ● Sensitivity : Sets the tampering detection sensitivity.
Event Rule Setup ● Event action : Displays the event action set in the event rule. Item You can set the event trigger and action rule to output an alarm when an event occurs. Description PTZ preset Setup > Event > Event rule setup Alarm output • setup E-mail Mobile push notification Monitor event ● Edit : Changes the registered event rule. Register a new event rule ● Add : Adds a new event rule by selecting from rule creation or rule copy. ● Delete : Deletes the selected event rule.
setup ● Schedule : Select the schedule to run the event action. ● Event action : Click <+ Add action> to set the event action. Alarm Input – PTZ preset : Set the PTZ preset to be displayed when an event occurs. Click < for each channel. > to set camera presets You can set the operation of the alarm sensor. Setup > Event > Alarm input – Alarm output : Set the alarm out to be generated when an event occurs.
Schedule Setting the Device When setting the event rule, you can set the operating time of the event action. You can make the detailed settings for devices such as storage device and monitors. Setup > Event > Schedule Storage Device You can set the storage device usage and check the setting status. • setup Checking and formatting the device You can check storage devices and their capacity, usage as well as status. The connectable storage devices are HDD and USB.
setup ● ￭ The ARB feature is available only when your video is saved in the SD card after registering your Wisenet camera using the Wisenet protocol. Storage Status : Displays the working status of a storage device. Click the to display the storage status window. ￭ – Red : Displays the situation of video loss. ￭ – Green : Displays the normal situation without video recording losses. – View : Click to see detailed information.
Remote Device Monitor This function is only available for products that support the use of a remote controller. For products that support remote controls, see "Products supporting each feature" (Page 4) in the Product Specification Manual. You can set the information displayed on the monitor as well as the output system. Setup > Device > Monitor You can adjust the ID for a remote control to be used in connection with Recorder.
setup Extended monitor setting Configure analog video display This function is only available for products that support the use of an extended monitor. You can access the setting regarding the video display of the analog camera. For products that support extended monitor, see "Products supporting each feature" (Page 4) in the Product Specification Manual. ￭ If the monitor is set to Extended mode, spot output cannot be set. 1. Select for video display and click .
Text Registering a Text Device You can set the POS device setting to send text information and text event information. Device Settings You can make detailed settings for the POS device connected to the recorder. • setup Setup > Device > Text > Device ● Device : Displays the text device name registered by the user. ● Enable : Specifies whether to enable text device. ● Channel : Select a channel to add a device from a channel table. ● Port : Display a port number that is set.
setup Text Event Settings Setting the Network You can set the text to receive an alarm when an event occurs. You can set various network functions, such as monitoring live video by connecting to a network from a remote location and receiving an event by e-mail. Setup > Device > Text > Event IP & Port You can set the network connection route and protocol. Setting a network connection Sets the protocol and environment of the network.
Connecting and Setting the Network ● Networking may differ from the connection method, check your environment before setting the connection mode. 1. To access the Broadband Router's configurations, open a web browser on the local PC that is connected to the Broadband Router and enter the router's address (ex : http://192.168.1.1). When no router is used Manual mode – Internet connection : Static IP, leased line, and LAN environments allows connection between the Recorder and remote user. 2.
setup DDNS If a remote user accesses the network, you can set whether or not to use DDNS and the site to be connected. Setup > Network > DDNS To check Quick Connect status A progress bar and its message appears for a Quick Connect. ● Quick Connect Success : Message for a successful connection. ● Invalid Network Configuration : Message appears if the network configuration is not valid. Check the configuration. ● Please enable UPnP function of the router.
IP Filtering HTTPS You can prepare the list of IP addresses to allow or block access to a specific IP address. You can choose a secured connection system or install a certificate. Setup > Network > IP filtering Setup > Network > HTTPS • setup ● Filtering type ● Secure connection system : You can select a type of security connection system. – Deny registered IP : Access to the registered IP address will be limited.
setup 802.1x E-mail When connecting to a network, you can select whether to use the 802.1x protocol and install a corresponding certificate. You can send an e-mail to a Recorder-registered user at a specific time interval, or if an event occurs. 802.1x is an authentication system between a server and a client, which prevents hacking, virus infection, and information leakage of transmitted and received network data. SMTP Setting 802.
Event Setting SNMP You can set the interval and type of the event that will be sent to the user. The SNMP protocol allows system or network administrators to remotely monitor and configure the network devices. Setup > Network > E-mail > Event Setup > Network > SNMP • setup ● Delivery interval : Set the event interval. ￭ If a series of events occurs, the e-mail will be sent at the specified interval, not on each event. ● ● Recipient Setting Enable SNMP v1 : SNMP v1 is used.
setup DHCP Server Checking the status You can set the internal DHCP server and assign an IP address to the network camera. You can check the IP address assigned to the current DHCP server, MAC address, and the connected network port information. Network Setting Setup > Network > DHCP server > Network ● Network : You can set the IP range and time to activate as the recorder's DHCP server. To set the DHCP server 1. Click of the network you want to set as a server. 2.
P2P Setting the System This function is only available for products that support P2P. You can set the date, language, authority, etc. displayed when using the system, and query system information or log information. You can connect the recorder to Wisenet Mobile for easy use when using P2P service. Setup > Network > P2P Date/Time/Language Setup > System > Date/Time/Language ● Enable P2P : Select check box if you want to use P2P service. ● QR Code : Scan QR code by mobile device.
setup ● Holiday : A user can select specific dates as holidays according to their own preferences. Select a holiday from the calendar displayed by clicking . – The same applies to or settings as holidays. User You can manage users, such as adding or deleting users and granting different authorities for each user. Setting the Administrator You can set and change Administrator's ID and password. The administrator can use and set all menu items and functions.
User setting If you want to register a user You can create user groups and set authorities for each group. You can manage user information such as registering and deleting users in the created user group. Setup > System > User > User • setup 1. Click on the < > button to launch the user addition popup window. To add a user, click on . 2. Select a group. When registering a user, the selected group will be automatically registered. If you want to add a group 1.
setup Restriction Settings If the user has restricted access Set user's restricted access or network restriction. If a general user selects a menu to which they do not have access, an access restriction confirmation window will be displayed. If all rights are restricted, only the accessible menu of the live screen menu will be displayed, and only the user's own password can be changed. Items with restrictions will require logging in for use.
System Management To upgrade the current software version You can check the current system version and update to a new version, export data, setting initialization, and more. Checking the System information • setup You can check the current software version and MAC address before proceeding with the upgrade. Setup > System > System management > Product information 1. Connect a device storing the software to be updated. ￭ It may take about 10 seconds to recognize the device.
setup Settings Log You can export the information set in the recorder to a storage device and apply the same information to other recorders. You can check the log information related to system, events, and export. Setup > System > System management > Settings Checking the system log System Log shows log and timestamp on every system start up, system shutdown, and changes on system settings. Setup > System > Log > System log ● Storage device : Shows the connected storage device.
Checking the event log Checking the export log You can search recorded events including alarms, camera events and video loss. It also shows the log and its timestamp. You can search the user who performed the export and the execution time and details (time, channel, device, file type).
starting web viewer What is Web Viewer? Connecting Web Viewer Web Viewer is a software program with which the operator can access a remote Recorder for real-time monitoring, PTZ control (if configured) or search. 1. Open your web browser and type the IP address or URL of Recorder into the URL address box. 2. A user with the admin permissions should provide the admin ID and password. A registered user should provide the user ID and password.
Set the recorder password After factory reset, the password must be set for the recorder to access the web viewer. 2. Set the camera password in factory reset on the screen. If ID/PW is already set in the camera, register the ID/PW and click . Enter the password of the admin account, and click . • starting web viewer ￭ Click < > to view the basic guide for setting a password. Refer to the password setup rules.
starting web viewer 4. Set the daylight saving time on the screen, and then click . 5. To modify the date and time on the screen, select the check box. Set the date and time. 6. Click the button to complete the installation wizard.
live viewer You can check the video from camera registered in the Recorder connected from a remote PC. Also, you can adjust the camera and check the network transfer status. Menu Description Enables the Manual recording function of the recorder. Screen Layout of the Live Viewer Saves the video saved in the set time of the selected channel in PC in AVI format. • live viewer Clears the alarm in the event list and stops the alarm at the notification display of the system status.
live viewer Checking the System Status Checking Camera List The icon at the top of the screen indicates the status of the system. Displays the camera type, status, and name registered in the recorder. Name Description Live > List Displayed when a problem occurs with the pan or recording status. Displayed when an error occurs in the power supply. Displayed when the amount of input data by channel exceeds the set amount of data limit.
Checking the All Camera Status Network Status You can check the status of all cameras connected to the recorder. Click the < > button, followed by the tab. You can check the status of network bandwidth currently being received/transmitted. Live Status > button. You can check the status and transmission information of the camera connected to each • live viewer Click the < channel. ￭ To change the profile setup, click the button.
live viewer Changing the Pattern of Split Screen Full Screen Mode Click the < You can change to full screen mode, which has no top/bottom/left/right areas of the live screen. > button and select the desired split screen. The selected split screen is applied to the video window. Click < > at the bottom of the screen. To exit the full screen, press the ESC key on the keyboard or click < Changing Overall Channel Aspect Ratio Video screen ratio for all channels can be changed in live split screen mode.
Setting up the Live Layout Change of Layout Channel and Name This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a single layout. 1. Click < Live > List 2. Add or delete channels or rename layouts. 3. Click < Delete Layout Click < ● : Create a new layout. ● : Change the channel or name of the layout. ● : Save the changed layout. ● : Delete the added layout. ● / > to save the changed settings.
live viewer Real-Time Event Monitoring Check Event List Real-time events that occurred on the camera can be checked in the live video window and event list. When new events occur, the list of events will be updated accordingly. Live > Event ￭ The specified channels and events are displayed in the list according to the event rule setup. For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of Contents.
Live Screen Menu Event Instant Viewer Select an event to check from the event list, and click < occurred. > to play the recorded video at the time the event ￭ Instant viewer can play an event video for 1 minute. After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen menu. The live screen menu appears differently depending on the recorder operation status or the type of the registered camera.
live viewer Camera Video Control PTZ Mode By using the function icon in the video window, you can easily enable functions such as screenshot, video rotation, and PTZ control. You can run PTZ control of the selected channel. Select the desired channel and click < >. Enters the PTZ control mode. Capture Select a channel to capture video and click the < ￭ Depending on the camera, the PTZ control function and speed may be different. > button. The captured image is saved as .
Zoom In Channel Aspect Ratio You can zoom in or out using the mouse wheel. You can change the aspect ratio of each channel. If you scroll up using the mouse wheel, the selected video screen is enlarged by 10%, and a thumbnail window is displayed. Select the desired channel and click < REC It changes to the actual proportion of the video. • live viewer ￭ Scrolling up/down using the mouse wheel will zoom in/out the video screen by 10%.
live viewer PTZ Control Using Digital PTZ (D-PTZ) function PTZ Control Menu 1. Register a camera that supports the D-PTZ profile. If the connected network camera is a PTZ camera, the < camera channel is selected, you can control the PTZ. > icon is displayed in the camera list. When the ￭ In cameras that support the D-PTZ profile, you can use the D-PTZ function. 2.
To delete a registered preset Exporting Video 1. Click < You can export the recorded video by manually inputting the desired channel, date, and time. >. 2. Select the preset to delete, and click . 1. Click the < > button. 3. window will appear, and click . The selected preset will be deleted. • live viewer Running Preset 1. Click < >. 2. Double-click the preset you want to run from the list. The camera lens moves to the set position.
search viewer You can search and play the recorded video stored in the recorder by connecting the recorder remotely. Name Screen Layout of the Search Viewer Description Turns on/off the section setup. Saves the video of the selected channel in the designated path in AVI format. Calendar Play adjustment The date of the recorded video is displayed in orange, and the current date is displayed in a orange circle. Click the date in orange to view the recorded video information on the time line.
Time Search Text Search You can search the recorded data by the desired date and time conditions. You can search the data input to the POS device connected to the recorder. ￭ The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently depending on whether the data time zone recorded at the same time and daylight saving time (DST) is applied. • search viewer 1. Select < > in the menu. 2. Select a POS device to search.
search viewer Bookmark Search Search Results Export You can search for bookmarked data. Search results of events, texts and bookmarks can be exported to a file. Example) Bookmark search result export 1. Click < 1. Select < > in the search results list. > in the menu. 2. Select a channel to search. 3. Select the date and time to search. 4. Click the button. The bookmark search results will be displayed. Click the desired bookmark list to play.
Export Video by Section Setup You can select the desired section from the time line or search list during video playing and export it to a file. 1. Click the < > button 2. Select the start and end points of the desired section in the time line with the mouse. • search viewer 3. Click the < > button. 4. Select a layout to export and select the desired channel. 5. Set the start date/time and end date/time. 6. Enter a file name to save, and then click the button. 7.
play Play Search Results Play Button Name and Function You can play the recorded data and export the video you want during playback. Paused state To Adjust the Time Line You can move the playback position and zoom the time line in and out. ● ● ● Click the desired play position in the time line. The playback start position will be moved. Playback state ￭ Click the start point on the left side of the time line to move the playback position to the start point of the first video.
setup viewer You can configure the Recorder settings remotely on the network. Setting the Camera Screen Layout of the Setup Viewer You can check a list of cameras that are connected to the Recorder and configure the necessary settings. For details, refer to the "Setup > Setting the Camera" page in the Table of Contents. Register • setup viewer You can add a camera. Setup > Camera > Register Name Description Menu Click each menu to go to the menu screen.
setup viewer Camera Setup Profile Setup You can change the settings of the connected camera. You can set the profile for your camera. Setup > Camera > Camera setup Setup > Camera > Profile setup Record You can set the record profile for your camera. ● When you click the button, a new camera web browser window is opened. – This is not supported if the camera is connected to the RTSP protocol. – This is not supported if the camera is connected to DDNS, URL, or MAC Address.
Remote Setting the Recording You can set the video profile transmitted to the network and the expansion monitor. For details, refer to the "Setup > Setting the Recording" page in the Table of Contents. Record Schedule If you set a recording schedule for a specific date and time, the recording will start at that specific time. • setup viewer Setup > Record > Record schedule Camera Password You can change the passwords of all registered cameras at once.
setup viewer Record Options Setting the Event You can set the hard disk recording option. For details, refer to the "Setup > Setting the Event" page in the Table of Contents. ￭ You can set the recording duration separately for each channel. Setup > Record > Record options Event Setup You can set detailed settings for each channel's event detection mode. Setup > Event > Event setup Object detection You can change the AI object detection event setup.
Tampering detection Alarm Input You can change the tampering detection event setup. You can set the operation of the alarm sensor. Setup > Event > Alarm input • setup viewer Event Rule Setup You can set the event trigger and action rule to output an alarm when an event occurs. Setup > Event > Event rule setup ONVIF Setup You can set the camera registered with the Onvif protocol.
setup viewer Schedule Setting the Device Whether to output an alarm can be scheduled according to the day and time. The initial setting will be an event sync, and an alarm will be sent only when an event occurs. You can check a list of devices that are connected to the Recorder and configure the necessary settings. Setup > Event > Schedule For details, refer to the "Setup > Setting the Device" page in the Table of Contents.
Monitor Event You can set the information displayed on the monitor as well as the output system. It is possible to set total amount conditions and keywords to display events of a POS device. Setup > Device > Monitor • setup viewer ￭ If the screen does not work properly, see “Troubleshooting (FAQ)” in the Appendix. ￭ The Monitor Setup settings control the monitor connected to the Recorder. ￭ Video exceeding the resolution of 1080p will not be displayed from the secondary monitor.
setup viewer Setting the Network DDNS For details, refer to the "Setup > Setting the Network" page in the Table of Contents. You can set DDNS. IP & Port Setup > Network > DDNS A remote user can access the Recorder via the network to check the current mode and the IP address. Setup > Network > IP & Port IP address Specify the network connection path. IP Filtering You can prepare the list of IP address to allow or block accesses to a specific IP address.
HTTPS E-mail You can select a security connection system or install public certificates. You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users. Setup > Network > HTTPS Setup > Network > E-mail • setup viewer SMTP You can set the server that sends mails and specify if you use the authentication process. ￭ While using HTTPS, if you want to switch to HTTP, then abnormal operation can take place as the browser contains the setting values.
setup viewer Recipient DHCP Server You can set groups and recipients to receive emails. You can set the network camera IP address and check the details by setting up a DHCP server. Setup > Network > DHCP server Network You can set the internal DHCP server and assign an IP address to the network camera. SNMP Using the SNMP protocol, the system or network administrator can remotely monitoring the network devices and sets the environment.
P2P Setting the System This function is only available for products that support P2P. You can configure the various settings of the Recorder system. If you want to use P2P service, check the box. You need to scan the QR code on the screen to use the P2P service. For details, refer to the "Setup > Setting the System" page in the Table of Contents. Setup > Network > P2P Date/Time/Language Setup > System > Date/Time/Language System Time Set the date and time.
setup viewer User Restriction settings You can manage users, such as adding or deleting users and granting different authorities for each user. You can set the user permission. Setup > System > User Administrator You can change the admin ID or the password. System Management You can check the current system version and update to a new version, export data, setting initialization, and more. ￭ ID allows alphanumeric characters only. ￭ If the admin ID is not used for access, you cannot change the ID.
Settings Event log Using a storage device, you can apply the current configuration of Recorder to another Recorder. The event log lists recorded events, such as sensor events, camera events, or image losses. Press the Initialization button to return the network settings to their factory default state. Items in the category are excluded from the initialization.
export viewer SEC Backup Viewer Screen Layout of the Backup Viewer You can play a file that is backed up in the format of SEC. Backup in SEC format produces backup data file, library file and self-executable viewer file. If you run the backup file viewer, the backup data file will be played. HRX-1632_CAM 01 Recommended System Requirements 2021-04-27 20 :54 :13 H264(1920x1080), NONE PCs with a lower specification than the recommended below may not fully support forward/backward and highspeed playback.
Name Description Saves the current video's image as in an image file. Supports JPEG file format. Screen Printout / A toggle button. Each time you press this button, the audio output will toggle between activated and deactivated. • export viewer Audio Prints out the current screen. You should have installed the appropriate printer driver before you can print out the screen. You can adjust the volume level from 0 to 100.
appendix Use Joystick Using Virtual Keyboard The function is only available for the product that supports a joystick. For products that support joy stick, see page 4 "Products supporting each feature” of the Product Specification Manual. The SPC-2000 joystick is operated as follows : 1. For alphanumeric inputs, the virtual keyboard window appears. 2. Using a mouse, click on the desired character tab. 3. Select . Entered word is applied.
Troubleshooting Problem Problem Action Live video will be slow or cut off. ● ● Check if the network cable is connected properly. ● Ensure that you have set Network - Connection Mode. ● Check the IP setting of the PC or camera. ● Try the Ping Test. ● Check if there is a different device near the product uses the same IP. I registered a camera, but the web viewer does not show live video.
appendix Problem Exported data cannot be played on a PC or recorder. Recording does not work. Action Problem ● When setting the file format for exporting, first decide whether the device to be played is a PC or a recorder before setting. ● When playing on a PC, the export file format must be SEC. ● When playing on a recorder, the export file format must be recorder. In the live screen, the < > icon is displayed and the message window saying “Record data size exceeded limitation.
