Use and Care Manual

16 - English
Settings
Radio Setup
●
To listen to the radio, you must connect the
supplied FM antenna.
Operating the Radio with the Remote
Control
1. Press the FUNCTION button to select FM.
2. Tune to the desired station.
●
Preset Tuning 1 : Press the
5
button to
select PRESET, and then press the TUNING
UP, DOWN button to select a preset station.
- Before you can tune to preset stations, you
must add preset stations to the product's
memory.
●
Manual Tuning : Press the
5
button to select
MANUAL, and then press the TUNING UP,
DOWN button to tune in to a lower or higher
frequency.
●
Automatic Tuning : Press the
5
button to
select MANUAL, and then press and hold the
TUNING UP, DOWN button for a few seconds
to automatically search the band.
Selecting Mono or Stereo
Press the MO/ST button.
●
Each time you press the button, the sound
switches between STEREO and MONO.
●
In a poor reception area, select MONO for a clear,
interference-free broadcast.
Presetting Stations
Example : Presetting FM 89.10 into memory.
1. Press the FUNCTION button to select FM.
2. Press the TUNING UP, DOWN button to scroll
the FM frequencies, and then select <89.10>.
3. Press the TUNER MEMORY button (the yellow
C button at the bottom of the remote).
4. Press the TUNER MEMORY button again
within about 5 seconds. The station is stored in
memory.
✎
If you press the TUNER MEMORY button
repeatedly without changing the station, the
inputted station may be overwritten.
5. To preset another station, repeat steps 2 to 4.
●
To tune in to a preset station, press the
TUNING UP, DOWN button.
✎
To delete all Preset FM stations at once, press
the TITLE MENU button for about 5 seconds
in FM Manual mode until DEFAULT PRESET
appears on the display.
Recording FM Radio
You can record your favorite radio broadcast on a
USB storage device.
1. Insert a USB device into the USB jack on the
front of the product.
2. Press the FUNCTION button to select FM, and
then press the TUNING UP, DOWN button to
select the station you want to record.
3. Press the RED (A) button to start recording. The
recording process begins.
●
The recorded time is displayed on the left and
the recording time still available, based on
the amount of free space in the USB storage
device, is displayed on the right.
4. Press the EXIT button to finish your recording.
The recording is stopped and saved as an .mp3
file at the same time. To play the recorded file,
refer to "Playing Files on a USB Device".
✎
The recorded file is saved in the Tuner folder
which is created automatically.
✎
Only the
H
I
G
H
-
E
N
D
V
A
C
U
U
M
T
U
B
E
S
O
U
N
D
5V 0.5A
(OPEN/CLOSE),
H
I
G
H
-
E
N
D
V
A
C
U
U
M
T
U
B
E
S
O
U
N
D
5V 0.5A
(POWER), EXIT,
MUTE, and VOLUME +/-, buttons are operable
while FM radio is being recorded.
✎
If you don't press any buttons while recording,
the screen saver will be enabled.
✎
Sound effects, such as DSP, EQ, etc., are not
recorded during FM radio recording.
✎
The radio is recorded at a set, default volume
even if you change the volume or press the
MUTE button during the recording process.
✎
If you remove the USB device or Power Cable
during the recording process, the portion of
the file which has already been recorded may
not play back.
✎
Recording will not start if the remaining free
space in the USB storage device is less than
2MB.
✎
If the USB device is removed or has insufficient
space (under 2MB), the appropriate message
is displayed and the recording stops.