FULL MANUAL HW-Q900A Imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.
SAFETY INFORMATION CAUTION (for Canada) SAFETY WARNINGS This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Important Safety Instructions Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1. Read these instructions. 2. Keep these Instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
CONTENTS 01 Checking the Components 6 02 Product Overview 7 Top Panel of the Soundbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bottom Panel of the Soundbar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 Installing the Wall Mount 28 Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Wallmount Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
01 CHECKING THE COMPONENTS PAIR SOUND MODE VOL WOOFER SOUNDBAR Soundbar Main Unit Soundbar Remote Control / Batteries Subwoofer HDMI Cable Wall Mount Guide x2 Power Cord (Subwoofer, Soundbar) x2 x2 x2 (M4 x L10) Holder-Screw Screw Bracket-Wall Mount x4 Rubber-Foot • For more information about the power supply and power consumption, refer to the label attached to the product.
02 PRODUCT OVERVIEW Top Panel of the Soundbar Position the product so that the SAMSUNG logo is located on the top. 1 2 3 4 1 (Multi Function) Button • In standby mode, press the (Multi Function) button to turn on the Soundbar. • Press the (Multi Function) button to change the input source. 2 Display Displays the product’s status and current mode. D.IN → HDMI 1 → HDMI 2 → Wi-Fi → BT 3 (Mic On/Off) Button Press the button to turn the microphone on or off. 4 (Volume) Button Adjusts the volume.
7 HDMI TO TV (eARC/ARC) Connect to the HDMI jack on a TV. (See page 16) • When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable. • Do not connect this unit or other components to an AC outlet until all connections between components are complete.
03 USING THE SOUNDBAR REMOTE CONTROL Inserting Batteries before using the Remote Control (AA batteries X 2) Slide the back cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries (1.5V) oriented so that their polarity is correct. Slide the battery cover back into position. How to Use the Remote Control 1 Power 1 2 5 2 Source 6 7 3 4 8 3 Turns the Soundbar on and off. • Auto Power Down Function The unit turns off automatically in the following situations: • In D.
7 Press the indicated areas to select Up/Down/Left/Right. Up/Down/Left/ Right 8 Sound Control Press Up/Down/Left/Right on the button to select or set functions. • Music Skip Press the Right button to select the next music file. Press the Left button to select the previous music file. • ID SET Use this option when the Subwoofer or Surround Speakers are not connected or need reconnection. While powered off, press and hold the Up button for 5 seconds to perform ID SET. (See page 14.
Output specifications for the different sound effect modes Output Effect STANDARD SURROUND GAME PRO ADAPTIVE SOUND Input With Subwoofer only With Subwoofer & Wireless Rear Speaker Kit 2.0 ch 2.1 ch 2.1 ch 5.1 ch 5.1 ch / 7.1 ch (DTS) 5.1 ch / 7.1 ch (DTS) 7.1 ch 7.1 ch 7.1 ch Dolby Atmos®, DTS:X 7.1.2 ch 7.1.4 ch 2.0 ch 7.1.2 ch 9.1.4 ch 5.1 ch 7.1.2 ch 9.1.4 ch 7.1 ch 7.1.2 ch 9.1.4 ch Dolby Atmos®, DTS:X 7.1.2 ch 9.1.4 ch 2.0 ch 7.1.2 ch 9.1.4 ch 5.1 ch 7.1.2 ch 9.1.
Adjusting the Soundbar volume with a TV remote control Adjust the Soundbar volume using the TV’s remote control. • This function can be used with IR remote controls only. Bluetooth remote controls (remote controls that require pairing) are not supported. • Set the TV speaker to External Speaker to use this function. • Manufacturers supporting this function: VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA 1. Turn Off the Soundbar. 2. Push up and hold the WOOFER button for 5 seconds.
04 CONNECTING THE SOUNDBAR Connecting the power and units Use the Power cord to connect the Subwoofer and Soundbar to an electrical outlet in the following order: • For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label: Rear of the Soundbar Main Unit) 1. Connect the Power cord to the Subwoofer. Power Cord POWER Rear of Subwoofer 2. Connect the Power cord to the Soundbar.
Manually connecting the Subwoofer Before performing the manual connection procedure below: • Check whether the power cables for the Soundbar and subwoofer are connected properly. • Make sure that the Soundbar is turned off. 1. Turn off the Soundbar main. 2. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds. • The red indicator on the rear of the subwoofer turns off and the blue indicator blinks. 5 Sec Blinking blue fast Rear of Subwoofer Rear of Subwoofer 3.
LED Status Description Resolution Red and blue Blinking Malfunction See the contact information for the Samsung Service Center in this manual. NOTE • If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED on the rear of the sub-woofer will turn red after blinking in blue several times. • If you use a device that uses the same frequency as the Soundbar near the Soundbar, interference may cause some sound interruption.
05 USING A WIRED CONNECTION TO THE TV Method 1. Connecting with HDMI CAUTION • When both the HDMI cable and optical cable are connected, the HDMI signal is received first. • To connect the HDMI cable between the TV and Soundbar, be sure to connect the terminals marked ARC. Otherwise, the TV sound may not be output. • The recommended cable is High Speed HDMI Cable with Ethernet.
Method 2. Connecting using an Optical Cable Pre-connection Checklist • When both the HDMI cable and optical cable are connected, the HDMI signal is received first. • When you use an optical cable and the terminals have covers, be sure to remove the covers. Optical Cable (not supplied) Bottom of the Soundbar DIGITAL AUDIO IN (OPTICAL) OPTICAL OUT HDMI 1 Top of the Soundbar HDMI 2 D.IN 1.
06 USING A WIRELESS CONNECTION TO THE TV Method 1. Connecting via Bluetooth When a Samsung TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling. • Only one Samsung TV can be connected at a time. • Samsung TV that supports Bluetooth can be connected. Check the specifications of your TV. Top of the Soundbar 5 Sec PAIR OR BT PAIRING ND SOUODE M The initial connection 1. Press the (OR) PAIR button on the Soundbar remote control to enter the “BT PAIRING” mode. a.
Method 2. Connecting via Wi-Fi Pre-connection Checklist • Wi-Fi connection is available only on Samsung TV. • Check whether the wireless router (Wi-Fi) is turned on and the TV is connected to the router. • The TV and Soundbar must be connected to the same wireless network (Wi-Fi). • If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi connection between the TV and Soundbar. Contact your Internet service provider for details.
07 CONNECTING AN EXTERNAL DEVICE Method 1. Connecting using an HDMI Cable (Capable of Dolby Atmos decoding and playback) Pre-connection Checklist • If the Audio Output options include Secondary Audio, make sure Secondary Audio is set to Off. • Make sure that the content supports Dolby Atmos®. Top of the Soundbar HDMI 1 DIGITAL AUDIO IN (OPTICAL) OR HDMI 2 HDMI 2 External Device OR HDMI OUT HDMI IN (ARC) HDMI Cable HDMI 1 HDMI TO TV (eARC/ARC) HDMI Cable Bottom of the Soundbar 1. 2. 3. 4.
Method 2. Connecting using an Optical Cable Top of the Soundbar BD / DVD player / Settop box / Game console D.IN OPTICAL OUT Optical Cable (not supplied) DIGITAL AUDIO IN (OPTICAL) Bottom of the Soundbar HDMI 1 1. Use an optical cable (not supplied) to connect the DIGITAL AUDIO IN (OPTICAL) on the Soundbar main and the OPTICAL OUT port on the external device. 2. Turn on the Soundbar and external device. 3. To select “D.
08 CONNECTING A MOBILE DEVICE Method 1. Connecting via Bluetooth When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of cabling. • When you connect a paired Bluetooth device with the Soundbar off, the Soundbar automatically turns on. Top of the Soundbar 5 Sec Mobile device PAIR OR BT PAIRING ND SOUODE M The initial connection • When connecting to a new Bluetooth device, make sure the device is within 3.28 ft (1 m) distance. 1.
• A Bluetooth device may experience noise or malfunction under in the following conditions: ‒ When the body is in contact with the signal transceiver on the Bluetooth device or Soundbar ‒ In corners or when there is an obstacle in proximity, such as a wall or partition, where electrical changes may occur. ‒ When exposed to radio interferences by other products operating on the same frequency ranges, such as medical equipment, microwave ovens, and wireless LAN devices.
Getting Started with Amazon Alexa (Built-in Alexa) • • • • Amazon Alexa is a service provided by Amazon. This function may not be supported depending on the model or geographical area. This function only supports some languages, and the supported functions may differ depending on the geographical area. For product specification or compatibility, refer to the Samsung website (www.samsung.com). Using Alexa, you can play music, listen to news, see weather forecasts, and control home appliances.
Getting Started with Alexa on Amazon Product (Works with Alexa) • • • • • This function may not be supported depending on the model or geographical area. This function only supports some languages, and the supported functions may differ depending on the geographical area. For product specification or compatibility, refer to the Samsung website (www.samsung.com). This service is provided by Amazon and can be terminated at any time. Samsung does not assume responsibility for service availability.
Using the Tap Sound Tap the Soundbar with your mobile device to play the sound of content on the mobile device through the Soundbar. • This function may not be supported, depending on the mobile device. • This function is only compatible with Samsung mobile devices with Android 8.1 or later. SmartThings App Top of the Soundbar Mobile device 1. Turn on the Tap Sound function on your mobile device. • For details on how to turn on the function, refer to “Setting the Tap Sound function” below. 2.
09 CONNECTING TO APPLE AIRPLAY 2 This feature may not be available in some countries. Connect and use with an Apple product • With AirPlay 2, you can control your home’s audio system from your iPhone, iPad, HomePod, or Apple TV. • This Samsung Soundbar supports AirPlay 2 and requires iOS 11.4 or later. NOTE • Confirm that the Soundbar is connected to Wi-Fi. (Refer to Method 2.
10 INSTALLING THE WALL MOUNT 2. Align the Wall Mount Guide’s Center Line with the center of your TV (if you are mounting the Soundbar below your TV), and then fix the Wall Mount Guide to the wall using tape. • If you are not mounting below a TV, place the Center Line in the center of the installation area. Installation Precautions • Install on a vertical wall only. • Do not install in a place with high temperature or humidity. • Verify whether the wall is strong enough to support the product’s weight.
11 INSTALLING THE SOUNDBAR ABOVE A TV STAND 7. Install the Soundbar with the attached Bracket-Wall Mounts by hanging the Bracket-Wall Mounts on the Holder-Screws on the wall. Component x4 8. Slide the Soundbar down as shown below so that the Bracket-Wall Mounts rest securely on the Holder-Screws. • Insert the Holder-Screws into the wide (bottom) part of the Bracket-Wall Mounts, and then slide the Bracket-Wall Mounts down so that the Bracket-Wall Mounts rest securely on the Holder-Screws.
As illustrated in the image, align the center of the Soundbar with the center of the TV, carefully place the Soundbar onto the TV stand. At this time, place the microphone at the front of the stand not to interfere with voice recognition. TV Right end of Soundbar NOTE 12 SOFTWARE UPDATE Auto Update When the Soundbar is connected to the Internet, software updates automatically occur even when the Soundbar is turned off. • To use the Auto Update function, the Soundbar must be connected to the Internet.
13 TROUBLESHOOTING Initialization Top of the Soundbar Before seeking assistance, check the following. Soundbar does not turn on. • Check whether the power cord of the Soundbar is correctly inserted into the outlet. INIT With the Soundbar on, press the (Volume) buttons on the body at the same time for at least 5 seconds. “INIT” appears on the display and then the Soundbar is initialized. CAUTION • All the settings of the Soundbar are initialized.
In case the TV is not connected via HDMI TO TV (eARC/ARC) Soundbar will not connect to Wi-Fi. • Check whether the HDMI cable is correctly connected to the ARC terminal. (See page 16.) • Connection may not be possible due to the connected external device (set-top box, game machine, etc.). Directly connect the Soundbar. • HDMI-CEC may not be activated on the TV. Turn on the CEC on the TV menu. (Samsung TV: Home ( ) → Settings ( ) → General → • Check whether your wireless router is on.
14 LICENSE 15 OPEN SOURCE LICENSE NOTICE Dolby, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Confidential unpublished works. Copyright © 2012-2020 Dolby Laboratories. All rights reserved. To send inquiries and requests for questions regarding open sources, contact Samsung Open Source (http://opensource.samsung.
17 SPECIFICATIONS AND GUIDE Specifications Model Name HW-Q900A Weight 15.7 lbs (7.1 kg) 48.5 x 2.7 x 5.4 inches (1232.0 x 69.5 x 138.0 mm) Dimensions (W x H x D) Operating Temperature Range +41°F to +95°F (+5°C to +35°C) Operating Humidity Range 10 % ~ 75 % AMPLIFIER Rated Output power Supported play formats ((18 W x 6) +(10 W x 3) + (18 W x 6)) + 160 W Dolby 5.1ch / Dolby Digital Plus / Dolby TRUE HD / Dolby ATMOS DTS 5.
LIMITED WARRANTY TO ORIGINAL PURCHASER Samsung Electronics Canada Inc.(SECA), warrants that this product is free from defective material and workmanship. SECA further warrants that if this product falls to operate properly within the specified warranty period and the failure is due to improper workmanship or defective materials, SECA will repair or replace the product at its option. All warranty repairs must be performed by a SECA Authorized Service Center.
© 2021 Samsung Electronics Co., Ltd. All rights reserved. Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Center. HEADQUARTERS Samsung Electronics Canada Inc. 2050 Derry Road West, Mississauga, Ontario L5N 0B9 Canada TEL: 1-800-SAMSUNG (1-800-726-7864) www.samsung.com/ca/support Country Samsung Service Center Web Site CANADA 1-800-SAMSUNG(726-7864) 1-844-SAM-PAYS (726-7297) www.samsung.
MANUEL COMPLET HW-Q900A Imaginez les possibilités Nous vous remercions d’avoir fait l’acquisition de ce produit Samsung. Pour bénéficier d’un service plus complet, veuillez inscrire votre produit sur le site www.samsung.
INFORMATIONS RELATIVES À LA SÉCURITÉ ATTENTION (Pour le Canada) AVERTISSEMENTS POUR ÉVITER LES RISQUES DE CHOC ÉLECTRIQUE, NE DÉMONTEZ PAS LE CAPOT. L’APPAREIL NE CONTIENT PAS DE PIÈCES RÉPARABLES PAR L’UTILISATEUR. S’ADRESSER À UN SERVICE APRÈS-VENTE QUALIFIÉ. Reportez-vous au tableau ci-dessous pour comprendre les symboles pouvant figurer sur votre produit Samsung. MISE EN GARDE RISQUE DE CHOC ÉLECTRIQUE NE PAS OUVRIR Ce symbole indique la présence d’une haute tension à l’intérieur.
Nettoyage des parties textiles 12. Utiliser uniquement avec le chariot, la base, le trépied, le support ou la table spécifié par le fabricant ou vendu avec l’appareil. Si l’appareil est posé sur un meuble à roulettes, déplacez l’ensemble avec précaution pour éviter de faire tomber le lecteur et de vous blesser. 13. Débranchez l’appareil en cas d’orage ou lorsqu’il est inutilisé pendant une période prolongée. 14. Confiez toutes les réparations à un technicien qualifié.
CONTENU 01 Vérification des composants 6 02 Présentation du produit 7 Panneau supérieur du Soundbar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Panneau inférieur du Soundbar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 Installation du support mural 28 Précautions d’installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Composants de montage mural . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
01 VÉRIFICATION DES COMPOSANTS PAIR SOUND MODE VOL WOOFER SOUNDBAR Unité principale du Soundbar Télécommande/piles du Soundbar Caisson de basses Câble HDMI Guide de montage mural x2 Cordon d’alimentation (caisson de basses, Soundbar) x2 x2 x2 (M4 x L10) Vis de fixation Vis Support de montage mural x4 Pied en caoutchouc • Pour plus d’informations sur l’alimentation et la consommation électriques, reportez-vous à l’étiquette apposée sur le produit (Étiquette : Arrière de l’unité principale du
02 PRÉSENTATION DU PRODUIT Panneau supérieur du Soundbar 1 Positionnez le produit de manière à que le logo SAMSUNG soit situé sur le dessus. 2 3 4 1 Bouton (Multifonction) • En mode veille, appuyez sur le bouton (Multifonction) pour allumer le Soundbar. • Appuyez sur le bouton (Multifonction) pour changer la source d’entrée. 2 Écran Affiche l’état du produit et le mode actuel. D.
7 HDMI TO TV (eARC/ARC) Permet de connecter la prise HDMI d’un téléviseur. (Voir la page 16) • Pour débrancher le cordon d’alimentation d’une prise murale, tirez la prise. Ne tirez pas sur le câble. • Ne connectez pas cet appareil ou d’autres composants à une prise CA tant que toutes les connexions entre les composants ne sont pas établies.
03 UTILISATION DE LA TÉLÉCOMMANDE DU SOUNDBAR Insertion des piles avant d’utiliser la télécommande (2 piles AA) Faites glisser le couvercle arrière dans le sens de la flèche jusqu’à ce qu’il soit complètement retiré. Insérez 2 piles AA (1,5 V) orientées de sorte que leur polarité soit correcte. Refaites glisser le couvercle des piles à sa position initiale. Comment utiliser la télécommande 1 Alimentation 1 2 5 2 Source 6 7 3 4 8 3 Permet d’allumer et d’éteindre le Soundbar.
7 Appuyez aux endroits indiqués pour sélectionner haut/bas/gauche/droite. Haut/Bas/Gauche/ Droite 8 Commande du son Appuyez en haut, en bas, à gauche et à droite du bouton pour sélectionner ou définir des fonctions. • Saut de musique Appuyez sur le bouton de Droite pour passer au fichier de musique suivant. Appuyez sur le bouton de Gauche pour passer au fichier de musique précédent.
Utilisation des boutons masqués (boutons ayant plusieurs fonctions) Bouton masqué Page de référence Bouton de la télécommande Fonction WOOFER (Haut) Marche/Arrêt de la télécommande du téléviseur (Veille) page 12 Haut ID SET page 14 Égaliseur 7 bandes page 10 (Commande du son) Spécifications de sortie pour les différents modes d’effets sonores Sortie Effet STANDARD SURROUND GAME PRO ADAPTIVE SOUND Entrée Avec le caisson de basses uniquement Avec le caisson de basses et le haut-parleur arr
Réglage du volume du Soundbar avec la télécommande du téléviseur Contrôlez le volume du Soundbar à l’aide de la télécommande du téléviseur. • Cette fonction ne peut être utilisée qu’avec des télécommandes infrarouges. Les télécommandes Bluetooth (télécommandes qui nécessitent un appairage) ne sont pas prises en charge. • Réglez le haut-parleur du téléviseur à Haut-parleur externe pour utiliser cette fonction.
04 CONNEXION DU SOUNDBAR Connexion de l’alimentation et des unités Utilisez le cordon d’alimentation pour brancher le caisson de basse et la Soundbar dans une prise électrique en respectant la séquence suivante : • Pour plus d’informations sur les exigences en matière d’alimentation électrique et de consommation d’énergie, reportez-vous à l’étiquette apposée sur le produit. (Étiquette : Arrière de l’unité principale du Soundbar 1. Raccordez le cordon d’alimentation au caisson de basses.
Branchement manuel du caisson de basses Avant d’effectuer la procédure de branchement manuel ci-dessous : • Vérifiez que les câbles d'alimentation du Soundbar et du caisson de basses sont correctement connectés. • Assurez-vous que le Soundbar est éteint. 1. Éteignez le Soundbar. 2. Maintenez le bouton ID SET enfoncé à l'arrière du caisson de basses pendant au moins 5 secondes. • Le voyant rouge situé à l’arrière du caisson de basses s'éteint et le voyant bleu clignote.
Voyant État Description Résolution Rouge et bleu Clignotant Dysfonctionnement Consultez les coordonnées du centre de service Samsung dans ce manuel. REMARQUE • Si l’unité principale est éteinte, le caisson de basses passe en mode veille et la DEL STANDBY située à l’arrière du caisson devient rouge après avoir clignoté en bleu. • Si vous utilisez un appareil qui utilise la même fréquence que le Soundbar à proximité du Soundbar, des interférences peuvent donner lieu à des interruptions du son.
05 UTILISATION D’UNE CONNEXION FILAIRE AU TÉLÉVISEUR Méthode 1. Connexion avec un câble HDMI MISE EN GARDE • Lorsque le câble HDMI et le câble optique sont tous les deux connectés, le signal HDMI est reçu en premier. • Pour connecter le câble HDMI entre le téléviseur et le Soundbar, assurez-vous de connecter les bornes marquées ARC. Sinon, le son du téléviseur risque de ne pas être émis. • Le câble recommandé est un câble HDMI haute vitesse avec Ethernet.
Méthode 2. Connexion à l’aide d’un câble optique Liste de contrôle de pré-connexion • Lorsque le câble HDMI et le câble optique sont tous les deux connectés, le signal HDMI est reçu en premier. • Lorsque vous utilisez un câble optique et que les bornes sont munies de caches, assurez-vous de retirer les caches. Câble optique (non fourni) Dessous du Soundbar DIGITAL AUDIO IN (OPTICAL) OPTICAL OUT HDMI 1 Dessus du Soundbar HDMI 2 D.IN 1.
06 UTILISATION D’UNE CONNEXION SANS FIL AVEC LE TÉLÉVISEUR Méthode 1. Connexion par Bluetooth Lorsqu’un téléviseur Samsung est connecté via Bluetooth, vous pouvez entendre le son stéréo sans les tracas du câblage. • Un seul téléviseur Samsung peut être connecté à la fois. • Un téléviseur Samsung prenant en charge Bluetooth peut être connecté. Vérifiez les spécifications de votre téléviseur. Dessus du Soundbar 5 Sec PAIR OU BT PAIRING ND SOUODE M La connexion initiale 1.
Méthode 2. Connexion en Wi-Fi Liste de contrôle de pré-connexion • La connexion Wi-Fi est disponible uniquement sur les téléviseurs Samsung. • Vérifiez que le routeur sans fil (Wi-Fi) est activé et que le téléviseur est connecté au routeur. • Le téléviseur et le Soundbar doivent être connectés au même réseau sans fil (Wi-Fi). • Si votre routeur sans fil (Wi-Fi) utilise un canal DFS, vous ne pourrez pas établir de connexion Wi-Fi entre le téléviseur et le Soundbar.
07 CONNEXION D’UN APPAREIL EXTERNE Méthode 1. Connexion à l’aide d’un câble HDMI (décodage et lecture Dolby Atmos possible) Liste de contrôle de pré-connexion • Si les options de sortie audio incluent une sortie audio secondaire, vérifiez qu’elle est désactivée. • Vérifiez que le contenu prend en charge Dolby Atmos®.
Méthode 2. Connexion à l’aide d’un câble optique Dessus du Soundbar Lecteur BD/DVD/ Décodeur/Console de jeu D.IN OPTICAL OUT DIGITAL AUDIO IN (OPTICAL) Câble optique (non fourni) Dessous du Soundbar HDMI 1 1. Utilisez un câble optique (non fourni) pour connecter le port DIGITAL AUDIO IN (OPTICAL) au Soundbar principal et le port OPTICAL OUT à l’appareil externe. 2. Allumez le Soundbar et l’appareil externe. 3. Pour sélectionner le mode « D.
08 CONNEXION D’UN APPAREIL MOBILE Méthode 1. Connexion par Bluetooth Lorsqu’un appareil mobile est connecté par Bluetooth, vous pouvez entendre le son stéréo sans les tracas du câblage. • Lorsque vous connectez un appareil Bluetooth associé alors que le Soundbar est éteint, le Soundbar s’allume automatiquement.
• Un appareil Bluetooth peut émettre du bruit ou devenir défaillant dans les conditions suivantes : ‒‒ Lorsque le corps est en contact avec l’émetteur-récepteur de signal sur l’appareil Bluetooth ou le Soundbar ‒‒ Dans les coins ou lorsqu’il y a un obstacle à proximité, tel qu’un mur ou une cloison, où des changements électriques peuvent se produire.
Premiers pas avec Amazon Alexa (service Alexa intégré) • • • • Amazon Alexa est un service fourni par Amazon. Cette fonction pourrait ne pas être prise en charge selon le modèle ou la zone géographique. Cette fonction ne prend en charge que certaines langues. Les fonctions prises en charge peuvent varier selon la zone géographique. Pour connaître les spécifications ou la compatibilité du produit, visitez le site Web de Samsung (www.samsung.com).
Premiers pas avec Alexa sur un produit Amazon (Compatible avec Alexa) • • • • • Cette fonction pourrait ne pas être prise en charge selon le modèle ou la zone géographique. Cette fonction ne prend en charge que certaines langues. Les fonctions prises en charge peuvent varier selon la zone géographique. Pour connaître les spécifications ou la compatibilité du produit, visitez le site Web de Samsung (www.samsung.com). Ce service est fourni par Amazon et peut être résilié à tout moment.
Utilisation de la fonction Tap Sound Appuyez sur le Soundbar avec votre appareil mobile pour lire le son du contenu de l’appareil mobile via le Soundbar. • Cette fonction peut ne pas être prise en charge en fonction de l’appareil mobile. • Cette fonction n’est compatible qu’avec les appareils mobiles Samsung fonctionnant sous Android 8.1 ou une version ultérieure. Application SmartThings Dessus du Soundbar Appareil mobile 1. Activez la fonction Tap Sound sur votre appareil mobile.
09 CONNEXION À APPLE AIRPLAY 2 Cette fonction pourrait ne pas être disponible dans certains pays. Connecter et utiliser avec un produit Apple • AirPlay 2 vous permet de contrôler le système audio de votre domicile au moyen de votre iPhone, iPad, HomePod ou Apple TV. • Ce Soundbar Samsung prend en charge AirPlay 2 et nécessite iOS 11.4 ou version ultérieure. REMARQUE • Vérifiez que le Soundbar est connecté au Wi-Fi. (Voir Méthode 2.
10 INSTALLATION DU SUPPORT MURAL Précautions d’installation • Effectuez l’installation sur un mur vertical uniquement. • N’installez pas le produit dans un endroit où la température ou le taux d’humidité est élevé. • Vérifiez que le mur est suffisamment solide pour supporter le poids du produit. Sinon, renforcez le mur ou choisissez un autre point d’installation. • Achetez et utilisez les vis de fixation ou les chevilles adaptées au type de mur que vous possédez (plaque de plâtre, plaque de fer, bois, etc.
11 INSTALLATION DU SOUNDBAR AU-DESSUS D’UN SUPPORT DE TÉLÉVISEUR 7. Installez le Soundbar à l’aide des supports muraux en accrochant les supports muraux sur les vis de maintien sur le mur. Composant 8. Faites glisser le Soundbar vers le bas, comme illustré ci-dessous, de sorte que les supports muraux reposent fermement sur les vis de maintien.
Comme illustré sur l’image, alignez le centre du Soundbar avec le centre du téléviseur, puis placez soigneusement le Soundbar sur le support du téléviseur. À ce stade, placez le microphone à l’avant du support pour ne pas nuire à la reconnaissance vocale. TV 12 MISE À JOUR DU LOGICIEL Mise à jour automatique Lorsque le Soundbar est connecté à Internet, les mises à jour logicielles s’installent automatiquement, même lorsque le Soundbar est éteint.
13 DÉPANNAGE Initialisation Dessus du Soundbar Avant de communiquer avec l'assistance, effectuez les vérifications suivantes. Le Soundbar ne s’allume pas. INIT • Vérifiez si le cordon d’alimentation du Soundbar est correctement inséré dans la prise. Pendant que le Soundbar est allumé, appuyez sur les boutons (Volume) de l’unité pendant au moins 5 secondes. Le message « INIT » apparaît sur l’écran et le Soundbar s’initialise. Le Soundbar fonctionne par intermittence.
Si le téléviseur n’est pas connecté via HDMI TO TV (eARC/ARC) Le Soundbar ne se connecte pas par Wi-Fi. • Vérifiez que le câble HDMI est correctement connecté à la borne ARC. (Voir la page 16) • La connexion peut ne pas être possible en raison de l’appareil externe connecté (décodeur, machine de jeux, etc.). Connectez directement le Soundbar. • HDMI-CEC peut ne pas être activé sur le téléviseur. Activez le CEC dans le menu du téléviseur.
14 LICENCE 15 AVIS CONCERNANT LES LICENCES LIBRES Pour envoyer des demandes de renseignements et questions concernant les sources libres, communiquez avec Samsung Open Source (http:// opensource.samsung.com) Dolby, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Confidential unpublished works. Copyright © 2012-2020 Dolby Laboratories. All rights reserved.
17 SPÉCIFICATIONS ET GUIDE Caractéristiques techniques Nom du modèle HW-Q900A Poids 15,7 lbs (7,1 kg) 48,5 x 2,7 x 5,4 po (1232,0 x 69,5 x 138,0 mm) Dimensions (L × H × P) Plage de températures de fonctionnement +41°F à +95°F (+5 °C à +35 °C) Plage d’humidité de fonctionnement 10 % à 75 % AMPLIFICATEUR Puissance de sortie nominale Formats de lecture pris en charge ((18 W x 6) + (10 W x 3) + (18 W x 6)) + 160 W Dolby 5.1ch / Dolby Digital Plus / Dolby TRUE HD / Dolby ATMOS DTS 5.
GARANTIE LIMITÉE À L’ACHETEUR INITIAL Samsung Electronics Canada Inc. (SECA) garantit ce produit contre tout défaut de fabrication. SECA garantit aussi que si cet appareil ne fonctionne pas convenablement durant la période de garantie SECA se réservera le droit de réparer ou de remplacer l’appareil défectueux. Toutes les réparations sous garantie doivent être effectuées par un Centre de service autorisé SECA.
© 2021 Samsung Electronics Co., Ltd. Tous droits réservés. Comment contacter Samsung dans le monde Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service Consommateurs Samsung. SIÈGE SOCIAL Samsung Electronics Canada Inc. 2050 Derry Road West, Mississauga, Ontario L5N 0B9 Canada TEL: 1-800-SAMSUNG (1-800-726-7864) www.samsung.com/ca/support Pays Centre de service de Samsung Site Web CANADA 1-800-SAMSUNG(726-7864) 1-844-SAM-PAYS (726-7297) www.