Quick Guide (ver.1.0)

ManualsBrandsSamsung ManualsTVLN19C450E1D

English - 2

Changing the Screen Size

Your TV has several screen size options, each designed to work best with specic

types of video input. If you have a cable box or satellite receiver, it may have its own

set of screen sizes as well.

To change the screen size, press the P.SIZE button on your remote. The rst time

you press it, your TV displays the current setting. Thereafter, each time you press

the P.SIZE button, you change the size of the picture on the screen.

The following sizes are available:

Screen Fit

✎

displays a full HD picture covering the entire screen with no cutoff

on any side. It is only available when your TV inputs an HDMI (720p, 1080i,

1080p), Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.

Changing the Picture Mode

Your TV has three preset Picture Modes with factory adjusted settings, each

designed to give you an excellent picture under specic conditions.

The Picture Modes are listed and described in the table below:

Mode Description

Dynamic

Brightens picture. For a vibrant, enhanced image in brightly lit or

sunny room.

Standard For a bright, detailed picture in a normally lit room.

Movie For a studio quality cinema picture in a dimly lit or dark room.

To change the Picture Mode, follow these steps:

1. With the TV on, press the TOOLS button on your remote.

The Tools menu appears.

2. Using the ▲ or ▼ on your remote, select Picture mode.

3. On the Picture Mode menu, use the ◄ or ► on your remote to select

the Picture Mode you want.

4. Press the EXIT button to exit the menu.

Viewing the On Screen Menus

To view the On Screen Menus, follow these steps:

1. With the power on, press the MENU button

on your remote. The main menu appears.

The menu’s left side has the following menu

options: Picture, Sound, Channel, Setup,

Input, Application, and Support.

2. Press the ▲ or ▼ button on your remote to

select a menu option, and then press the ENTERE button.

3. When done using the menu, press the EXIT button on your remote to exit.

Remote Control Buttons and Functions:

P . MODE

MEDIA.P

ABCD

S.MODE

P . SIZE

SLEEP

MTS

Changing Channels and Adjusting the Volume

Channel

Volume

Change the channels by pressing

the

button on the remote.

You can also change the

channels by pressing the

buttons on

the front panel of your TV

and adjust the volume by

pressing the

buttons.

If your TV is attached to a cable or

✎

satellite box, change the channel

using the box’s remote.

Adjust the volume by pressing the

button on the remote.

MEDIA.P

A BCD

MEDIA.P

A BCD

Power Indicator

Remote control sensor

Step 5 :

Run Plug & Play

When you turn on your TV for the rst time, it automatically launches the Plug &

Play function. With Plug & Play, you can select the On Screen Display language,

set the clock mode, and launch the TV’s channel memorizing process. It also

displays connection instructions similar to those in this guide.

To navigate while Plug & Play is running, press the Up, Down, Left or Right

arrow buttons on your remote. To make a selection, press the ENTERE button.

To skip a screen, press the MENU button.

To turn on your TV, press the POWER button on the remote or press the

POWER button on the TV. To run Plug & Play, follow these steps:

Select Language of the OSD.

Language : English

Move

Enter

Plug & Play

English

Español

Français

1. On the Language screen, select the language for the On Screen Display

(OSD) using your remote control, and then press ENTERE button. The

Home Use screen appears.

2. Select Home Use, and then press ENTERE button. If you select Store

Demo, the TV will reset your picture and audio settings every 30 minutes. After

you press ENTERE button, the Antenna Source screen appears.

3. If your TV is only attached to an antenna, select Air. If your TV is only

attached to cable and you have no cable box, select Cable. If your TV is

attached to an antenna and cable with no box, select Auto. When done,

press ENTERE button on your remote. The Select Cable System screen

appears.

IMPORTANT:

If your TV is attached to a cable or satellite box, skip Steps

3 through 5. After

Plug & Play

is complete, set your TV to Channel 3 or 4,

according to the directions for your cable or satellite box.

4. If your TV is attached to a cable system and you have no cable box, you

must select your cable system type. If you have Digital cable, you must

select the cable system type for both Analog and Digital.

After you have selected the cable system type, select Start, and then

press the ENTERE button on your remote.

Most cable systems are Standard

✎

(STD) systems. If you are not sure

about what kind of cable system you have, contact your cable company.

5. The TV memorizes the available channels. This process can take up

to 45 minutes. After the TV has memorized the channels, the Clock Mode

screen appears.

6. Choose the Clock Mode. Select Auto if you have a digital channel in your

area. Select Manual if you don’t, or if you have a cable or satellite box.

When done, press ENTERE button. The Daylight Savings screen appears.

If you select

✎

Manual, the clock setting screen appears.

7. Select the daylight saving time setting: Off, On, or Auto, and then press

ENTERE button.

8. After the time zone screen, The connection method for best HD screen quality

is displayed. Press Right arrow button on your remote to view each screen in

succession. Press the MENU button to skip this section.

9. The Enjoy your TV screen appears.and then press ENTERE button.

Selecting a Source

To watch a movie on your Blu-ray player or watch your favorite TV show, you must

select the correct source. A source is a device, such as a Blu-ray/DVD player, a

cable/satellite box, antenna or a cable TV input.

Sources can be connected to your TV through

the HDMI, DVI, Component, Composite, or D-sub

connections, or through the Antenna or Cable In

connections.

To view the signal from a source connected to the

HDMI, DVI, Component, Composite, or D-sub jack, press the SOURCE button on

your remote. Each time you press the SOURCE button, you change to a different

source.

Basic Functions

MEDIA.P

A BCD

Setting the Clock

Before you can use your TV’s On/Off Timer, you must set the clock. To set the

clock, follow these steps:

1. Turn on your TV.

2. Using your remote, press the

MENU button on your remote.

Then, select Setup → Time.

3. Select Clock Mode, and then

press the ENTERE button. Set

Clock Mode to Manual.

Select Auto if you have a

✎

digital channel in your area

and are not using a cable/sat

box.

4. Select Clock Set, and then press the ENTERE button.

The Clock Set screen appears.

5. Using the number buttons on your remote, enter the month, day, year, hour,

and minute. Use the ◄ or ► button to move between entry elds.

6. Press the RETURN button on your remote when done.

Connecting a USB Device for Media Play

You can enjoy photo, music, and movie ﬁles

stored on a USB device by connecting it to the TV

and using the Media Play feature. To connect a

USB device for Media Play, follow these steps:

1. Turn on your TV.

2. Connect a USB device containing

photo, music and/or movie les to

the USB jack on the rear of the TV.

3. When the Application selection

screen appears, press the

ENTERE button on your remote

to select Media Play (USB).

16:9 Wide screen

Wide Fit

Zoom 1

4:3 Standard screen

Zoom 2

Screen Fit

MEDIA.P

A BCD

BN68-02606A-03

Clock Set

Move

Adjust

Enter

Retour

Month

Hour

Day

Minute

Year

am/pm

----

Move

Enter

Return

Press to select additional digital channels broadcast by

the same station. For example, to select channel 54-3,

press 54, press -, and then press 3.

Press number buttons for direct access to channels.

Turns the TV on and off.

Displays the channel list on the screen.

Quickly selects frequently used functions.

Return to the previous menu.

View the Media Play.

Colored buttons for use in the Channel List, Media Play

menu, etc.

Adjust the volume.

Use these buttons in the Media Play and Anynet+ modes.

(

: Controls recording on Samsung recorders with the

Anynet+ feature)

Use these buttons to select On Screen Menu items

and change menu settings.

Return to the previous channel.

Press to switch between the sources (Blu-ray player,

cable box, DVD player, etc.) connected to your TV.

Cut off the sound temporarily.

Display Favorite Channel Lists on the screen.

Press to display information on the TV screen.

Exit the menu.

Change channels.

Display the main on-screen menu.

S.MODE: Select the sound mode.

SLEEP: Setting the Sleep Timer.

MTS: Press to choose stereo, mono or Separate

Audio Program (SAP broadcast).

P.MODE: Select picture mode.

P.SIZE: Choose the picture size.

CC: Controls the caption decoder.

TV Rear Panel

USB Drive

[LC450-QSG]BN68-02606A-03Eng.indd 2 2010-08-31 �� 3:35:38