SyncMaster F2080,F2380 LCD MONITOR quick start guide
1 Installing the Product 1-1 Package Contents • Unpack the product and check if all of the following contents have been included. • Store the packaging box in case you need to move the Product at a later stage. Monitor Contents Installation Manual Product Warranty Power Cord D-Sub Cable 1-2 User Manual DVI Cable(option) Installing the Stand Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards. Do not remove the stopper pin before installing the base. Hold the main body of the product with your hand as shown by the figure. Insert the stand base into the stand connection part in the direction shown in the figure. Turn the connecting screw at the bottom of the stand fully so that it is completely fixed.
After the installation of the base, stand the monitor up as shown in the figure. Now you can remove the stopper pin to adjust the stand. - Caution Avoid lifting the product holding only the stand. Disassembly is in the reverse order of the assembly. 1-3 Installing the Stand for the Wall Mount Before installation, disassemble the product according to the following steps.
Lift up the monitor stand to the maximum angle with your left hand, and remove the back decoration cover with your right hand, as shown in the figure. Remove the screw on the point "A". Remove the part in the direction shown in the figure. This product provides a stand mount of 100 mm x 100 mm(200 mm x 100 mm) that complies with the VESA specifications. A. Stand Mount B. Stand (Optional) 1. Turn the product off and unplug the power cord from the wall outlet. 2.
• If you use a screw that is longer than the standard specifications, the inside of the product may be damaged. • For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ depending on the corresponding specifications. • Do not use screws that are incompatible with the standard VESA specifications and do not assemble them using excessive force. This may result in damage to the product or injury due to the product falling.
(The input voltage is switched automatically.) POWER S/W ON [ │ ] / OFF Switches the LCD Display On/Off. When the product is connected to a PC, you can turn the product on and use it. When all the DVI (digital) and D-Sub (analog) cables are connected, you can select the input signal (Analog/Digital 1/Digital 2) by pressing the 1-5 /SOURCE button.
Locking the product 1. Insert the locking part of the locking device into the hole of the Kensington lock of the product and turn it in the locking direction. 2. Connect the Kensington lock cable. 3. Tie the Kensington lock cable to a desk or heavy object. You can purchase the locking device from an electronics store, an online shop, or our service center. 1-6 Product Operating Buttons Product Operating Buttons Icon MENU Description Press this button to view the On Screen Display (OSD).
Icon AUTO Description Press [AUTO] button to adjust the screen settings automatically This function is only available in analog mode. If the resolution settings are changed in the Display Properties, the AUTO adjustment function is performed. Press this button to turn the product on or off • The buttons on the right of the product are touch-type buttons. • Touch the buttons lightly with your finger. Power LED This LED is turned on when the product works normally.
2 Troubleshooting 2-1 Monitor Self-Diagnosis • You can check if the product is working properly using the Self-Diagnosis function. • If a blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected, perform the self-diagnosis function according to the procedures below. 1. Turn the product and the PC off. 2. Separate the signal cable from the product . 3. Turn the product on. 4. If the product is working properly, the 'Check Signal Cable' message appears.
The display area suddenly moves to an edge or to the center. Did you change the graphics card or the driver? Please press the [AUTO] button to run the auto adjustment function. Did you change the resolution and frequency appropriate to the product? Set the resolution and the frequency to the appropriate values in the graphics card refer to the (Standard Signal Mode Table) Is the graphics card configured correctly? Set up the graphics card referring to the user manual. The pictures are out-of-focus.
FAQ! How can I change the resolution? Please try the following! Windows XP : Change the resolution by selecting Control Panel → Appearance and Themes → Display → Settings. Windows ME/2000 : Change the resolution by selecting Control Panel → Display → Settings. (For more information, refer to the User Manual of the computer or the graphics card.
