LCD MONITOR quick start guide SyncMaster XL24 ii
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Power Cord DVI Cable USB Cable (A-B Type cable) Others Calibrater For more information on the use of the calibrater, see Natural Color Expert Help.
MODE button (= Color Mode) Press this button to select a Color Mode. Continuing to press the button, will repeatedly display the setting modes. With the control buttons at the front of the monitor, you can easily implement different color information matching your environment. 1) Custom - Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
Rear (The configuration at the back of the monitor may vary from product to product.) DVI Connect the DVI terminal of your monitor to your computer using a DVI cable. 1. DVI-D (digital only): Only digital signals can be input to this terminal. Therefore, only connect the DVI terminal of your PC to this terminal. 2. DVI-I (for both digital and analog) : You can connect any one of the DVI and RGB terminals of your PC to this terminal.
Kensington Lock The Kensington lock is a device used to physically fix the system when using dit in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchased it. USB connection terminal DOWN (USB downstream port): Connect the DOWN port of the USB monitor and a USB device with the USB cable. z To use DOWN (Downstream Port), you have to connect the UP (Upstream Cable ) to the PC.
Connecting the Monitor Connecting the Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor. [ DVI-D ] [ DVI-I ] Connected to a Macintosh. Connect the monitor to the Macintosh computer using the DVI connection cable.
Changing the Stand and Installing the Hoods Sliding Stand Stand Stopper Swivel stand Using ( ),You can swivel the monitor left and right at an angle of 330 ° to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide.
Using ( angle. ), You can adjust the tilt angle forward and backward for the most comfortable viewing Removing the base 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove two screws ( ) and then remove the Stand from the LCD monitor. Attaching a Base This monitor accepts a 200 mm x 100 mm VESA-compliant mounting interface pad.
A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
Insert the hooking parts ( ) of both hoods starting from the top and moving downwards into the grooves ( ) near the left and right edges at the back of the monitor. Fit the top part of the monitor into the top of the grooves of both hoods.
Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
display will work properly but the "Not Optimum Mode", "Recommended Mode 1920 x 1200 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen. The monitor is in PowerSaver mode. Is the power indicator on the monitor blinking at 1 second intervals? press a key on the keyboard to activate the monitor and restore the image on the screen.
The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Settings. Has the video card been set properly? Set the video card by referring to the video card manual. Have you installed the monitor driver? Install the monitor driver according to the Driver Installation Instructions. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
