SyncMaster XL24 Install driver Install programs
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for an extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug. z This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. (Class l Equipment only.) Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
z This may cause electric shock or fire. Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust.
Keep any heating devices away from the power cable. z A melted coating may cause electric shock or fire. Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. z Any increase in the internal temperature may cause fire. Put down the monitor carefully. z Failing to do so may damage the monitor. Do not place the monitor face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional.
a slightly moistened, soft fabric. Do not spray water or detergent directly onto the monitor. z This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. z Otherwise, this may cause electric shock or fire.
do not install inside a vehicle. z z This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center . z The monitor may malfunction, causing electric shock or fire.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. z This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center. When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.
z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product. z Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality. When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Power Cord DVI Cable USB Cable (A-B Type cable) Others Calibrater For more information on the use of the calibrater, see Natural Color Expert Help.
MODE button (= Color Mode) Press this button to select a Color Mode. Continuing to press the button, will repeatedly display the setting modes. With the control buttons at the front of the monitor, you can easily implement different color information matching your environment. 1) Custom - Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
Rear (The configuration at the back of the monitor may vary from product to product.) DVI Connect the DVI terminal of your monitor to your computer using a DVI cable. 1. DVI-D (digital only): Only digital signals can be input to this terminal. Therefore, only connect the DVI terminal of your PC to this terminal. 2. DVI-I (for both digital and analog) : You can connect any one of the DVI and RGB terminals of your PC to this terminal.
Kensington Lock The Kensington lock is a device used to physically fix the system when using dit in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchased it. USB connection terminal DOWN (USB downstream port): Connect the DOWN port of the USB monitor and a USB device with the USB cable. z To use DOWN (Downstream Port), you have to connect the UP (Upstream Cable ) to the PC.
Connecting the Monitor Connecting the Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor. [ DVI-D ] [ DVI-I ] Connected to a Macintosh. Connect the monitor to the Macintosh computer using the DVI connection cable.
Changing the Stand and Installing the Hoods Sliding Stand Stand Stopper Swivel stand Using ( ),You can swivel the monitor left and right at an angle of 330 ° to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide.
Using ( angle. ), You can adjust the tilt angle forward and backward for the most comfortable viewing Removing the base 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove two screws ( ) and then remove the Stand from the LCD monitor. Attaching a Base This monitor accepts a 200 mm x 100 mm VESA-compliant mounting interface pad.
A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
Insert the hooking parts ( ) of both hoods starting from the top and moving downwards into the grooves ( ) near the left and right edges at the back of the monitor. Fit the top part of the monitor into the top of the grooves of both hoods.
Installing the Monitor Driver (Automatic) When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. z Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.
Windows Vista | Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. z Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ 6. Click "Update Driver…" in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". 9.
10. Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System 1. Insert the CD into the CD-ROM driver. 2. Click "Start," click "Control Panel," and then click the "Appearance and Themes" Icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced.
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver." and select "Install from a list or." then click "Next" button. 6. Select "Don't search ,I will" then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Choose the "Settings" tab and then click "Advanced." Choose "Monitor." Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click "Update Driver" then click the "Next" button.
[ ]These buttons allow you to adjust items in the menu. [ ]Press this button to activate a highlighted menu item. [AUTO]Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are adjusted automatically. [ ]Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
- When pressing the MENU button after locking the OSD Menu Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the MENU button for more than five seconds to activate the OSD adjustment lock function. Locked Unlock : Hold down the MENU button for more than five seconds to deactivate the OSD adjustment lock function.
Menu Contrast Description When the OSD is not visible, push the button to adjust the Brightness. Brightness Menu Brightness SOURCE Description When OSD is not visible, push the button to adjust the Contrast.
Menu Description Selects the video signal while the OSD is off.
Menu Brightness Description You can use the on-screen menus to change the brightness according to personal preference. [MENU → Contrast → , → MENU] You can use the on-screen menus to change the contrast according to personal preference.
Menu Color Tone Description Adjusts color tones to the preference of the user. - Warm5~Warm1, Off, Cool1~Cool6 [MENU → , Color Control → → , → → , → MENU] Adjusts individual R,G,B color balance. [MENU → , Gamma Play/Stop → → , → → , → → , → MENU] Gamma correction changes the luminance of the colors with intermediate luminance. (-0.6 ~ +0.6) [MENU → , → → , → → , → MENU] Image Menu Coarse Description Removes noise such as vertical stripes.
[MENU → , V-Position → → , → → , → MENU] Changes the vertical position of the monitor's entire display. (Available in analog mode only) [MENU → , → → , → → , → MENU] OSD Menu Description You can choose one of 9 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. [MENU → , H-Position → MENU] → → , → → , → MENU] → → , → → , → MENU] Change the transparency of the background of the OSD.
is turned off. [MENU → , → → , → → , → MENU] Setup Menu Auto Source Description Select Auto Source for the monitor to automatically select the signal source. [MENU → , Image Reset → , → MENU] → → , → → , → MENU] Color parameters are replaced with the factory default values. [MENU → , Indicator → Image parameters are replaced with the factory default values. [MENU → , Color Reset → → → , → → , → MENU] Turns all LEDs On or Off.
Menu Information Description Shows a video source, display mode on the OSD screen.
This program does not support MAC. Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicRotation installation file. 3. Select installation Language, Click "Next". 4. When the InstallShield Wizard window appears, click "Next." 5. Select "I accept the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicRotation program. 7. Click "Install." 8. The "Setup Status" window appears.
9. Click "Finish." Have to reboot the system in order for the MagicRotation to work properly. 10. When the installation is complete, the MagicRotation executable icon appears on your desktop. Installation Problems The installation of MagicRotation can be affected by the factors such as video card, motherboard and the network environment. Limitation 1. The "Display Driver" should be properly loaded for the MagicRotation to work properly.
Close the application. Select the Orientation (90, 180, 270) you want to view the application. { Relaunch the application. In most cases this should fix the problem. { { 3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the orientation mode selected (90, 180, 270). e.g. 3D games 4. DOS based applications in Full Screen Mode will not function as per the orientation mode selected (90, 180, 270). 5. Dual is not supported in Windows® 98, ME, NT 4.0. 6.
Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
display will work properly but the "Not Optimum Mode", "Recommended Mode 1920 x 1200 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen. The monitor is in PowerSaver mode. Is the power indicator on the monitor blinking at 1 second intervals? press a key on the keyboard to activate the monitor and restore the image on the screen.
The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Settings. Has the video card been set properly? Set the video card by referring to the video card manual. Have you installed the monitor driver? Install the monitor driver according to the Driver Installation Instructions. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
General General Model Name SyncMaster XL24 LCD Panel Size 24 inch (61 cm) Display area 518.4 (H) x 324.0 (V) Pixel Pitch 0.270 (H) x 0.270(W) Synchronization Horizontal 30 kHz ~ 81 kHz Vertical 56 Hz ~ 85 Hz Display Color 16.7M Resolution Optimum resolution 1920 x1200@60 Hz Maximum resolution 1920 x1200@60Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ± 5 % separate H/V sync, Composite TTL level (V high ≥ 2.0 V, V low ≤ 0.
563 x 382.5 x 92.8 mm / 22.2 x 15.1 x 3.7 inch (Without Stand) 563 x 461.7 x 250 mm / 22.2 x 18.2 x 9.8 inch (With Stand), 10.0 Kg / 22.0 lbs VESA Mounting Interface 200 mm x 100 mm Environmental considerations Operating Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C) Humidity : 10 % ~ 80 %, non-condensing Storage Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG(726-7864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421, 4004-0000 http://www.samsung.com/br CHILE 800-SAMSUNG(726-7864) http://www.
AUSTRIA 0800-SAMSUNG(726-7864) http://www.samsung.com/at BELGIUM 0032 (0)2 201 24 18 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(726-7864) 08 25 08 65 65(€ 0,15/Min) http://www.samsung.com/fr GERMANY 01805-SAMSUNG(726-7864) (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG(726-7864) http://www.samsung.
INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.com/jp MALAYSIA 1800-88-9999 http://www.samsung.com/my NEW ZEALAND 0800SAMSUNG(726-7864) http://www.samsung.com/nz PHILIPPINES 1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG(726-7864) http://www.samsung.com/sg THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.
horizontal dots (horizontal resolution) and 1200 vertical lines (vertical resolution). For Better Display 1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. { { Resolution: 1920 x 1200 Vertical frequency (refresh rate): 60 Hz 2.
DISCLAIMER WORDING FOR ADOBE SOFTWARE PRODUCTS (Europe) Samsung Electronics Company Limited and its subsidiaries (together "Samsung") have not been provided with any warranties from Adobe Systems Incorporated ("Adobe") in relation to the Adobe software products (the "Adobe Software Products") which are bundled together with Samsung products (the "Samsung Products") within the Samsung LCD Monitor to which this agreement relates (the "Monitor").
costs or for any claim by any third party. The foregoing limitations and exclusions apply to the extent permitted by applicable law in your jurisdiction. Samsung's aggregate liability related to or in connection with any claims which you able to bring in relation to the Adobe Software Products under the applicable law of your jurisdiction shall be limited to the amount paid for the Adobe Software Products by Samsung.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
