SyncMaster 570DX Model SyncMaster 570DX Select Language Install Programs PDF Manuals Registration Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix © 2007 Samsung Electronics Co., Ltd. All rights reserved.
Select Language Main Page Model SyncMaster 570DX Safety Instructions Notational Power Installation Clean Others Introduction The color and appearance of the product may vary depending on the model, and the product specifications are Connections subject to change without prior notice for reasons of performance enhancement.
Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. z This may cause electric shock or fire. Do not connect too many extension cords or plugs to one outlet. z This may cause fire.
Failure to do so may cause electric shock or fire inside the LCD Display. z Do not drop the LCD Display when moving it. This may cause damage to the product or the person carrying it. z Install the LCD Display base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or the person z carrying it. Do not place the product on an unstable or small surface area.
z Failing to do so may damage the LCD Display. Do not place the LCD Display face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. z Installing the bracket by unqualified personnel may result in injury. z Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inches) for ventilation purposes.
z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. z Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. z Failure to do so may cause electric shock or fire. Do not try to move the LCD Display by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the LCD Display right or left by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable.
z This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center. When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. z Change the mode to energy saving mode or set a screensaver to a changing picture when away from the LCD Display for an extended period of time.
Place the product out of children’s reach, as they could damage by hanging onto it. z A falling product may cause injury to the person or even fatality. When not using the product for an extended period of time, keep the product unplugged. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product.
recycling center or to a store selling the same type of the battery or rechargeable battery. © 1995~2007 SAMSUNG.
Select Language Main Page Model SyncMaster 570DX Safety Instructions Introduction Package Contents Your LCD Display Machanical Layout Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Remote Control Batteries (AAA X 2) Cover-Hole Semi Stand Screw: 4 EA BNC to RCA Adaptor Jack Sold separately Wall Mount KIT Speaker Set BNC Cable Speaker Wire Cable DVI Cable Your LCD Display Front 1) MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2) Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values.
3) Adjust buttons (Left-Right buttons)/ Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. 4) ENTER Activates a highlighted menu item. 5) SOURCE Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [PC] → [BNC] → [DVI] → [AV] → [S-Video] → [Component] >> Click here to see an animation clip.
1) POWER S/W ON [ | ] / OFF [O] 2) POWER IN Switches the LCD Display On/Off. The power cord plugs into the LCD Display and the wall plug. 3) REMOTE OUT/IN You can use a wired remote control by connecting it to your monitor.
Audio Connection Terminal (Input)) 12) AV OUT [VIDEO] (VIDEO Connection Terminal): AV mode (Output) 13) AV IN [VIDEO] (VIDEO Connection Terminal) (Input) 14) AV OUT [S-VIDEO] (S-VIDEO Connection Terminal): S-VIDEO mode (Output) 15) AV IN [S-VIDEO] (S-VIDEO Connection Terminal) (Input) 16) EXT SPEAKER(8 Ω)[- - L - +, - - R - +] (EXT Speaker Connection Terminal) 17) AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connection Terminal (Output)) AUDIO OUT is the terminal for sound output of PC, DVI or BNC.
23. P.SIZE 24. 25. SRS DUAL/MTS 26. PIP 27. SOURCE 28. SWAP 29. 30. 31. 32. 33. 1) SIZE REW STOP PLAY/PAUSE FF ON / OFF Turns the LCD Display On/Off. 2) MAGICNET MagicNet Quick Launch Button. - This fuction does not work for this monitor. 3) MDC MDC Quick Launch Button. 4) LOCK Activates or deactivates all function keys on both the remote control and the LCD Display except for the Power and LOCK buttons. 5) MagicNet buttons Used for MagicNet.
TV channels provide text information services via teletext. - This fuction does not work for this monitor. 10) MENU Opens the on-screen menu and exits from the menu screen or closes the screen adjustment menu. ENTER 11) Activates a highlighted menu item. 12) P.MODE When you press this button, current picture mode is displayed on the lower center of the screen. AV / S-Video / Component : P.MODE The Monitor has four automatic picture settings that are preset at the factory.
STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. MTSYou can select MTS (Multichannel Television Stereo) mode. Audio Type MTS/S_Mode FM Stereo Mono Mono Stereo Mono ↔ Stereo SAP Mono ↔ SAP Default Manual Change Mono - This fuction does not work for this monitor. 26) PIP Every time you press the button, a PIP screen appears.
Mechanical Layout | Monitor Head | Speaker | Installation VESA Bracket | Wall Bracket Installation 1. Mechanical Layout 2. Monitor Head 3.
4. Installation VESA Bracket z z z z When installing VESA, make sure to comply with the international VESA standards. Purchasing VESA Bracket and Installation Information : Please contact your nearest Samsung Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. At least 2 persons are needed in order to move the LCD Monitor.
5. Wall Bracket Installation z z z Contact a technician for installing the wall bracket. Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components Only use the components and accessories shipped with the product.
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) Remove the 4 screws on the back of the product.
1. Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. 2. Be careful when installing the product on the bracket as fingers can be caught in the holes. 3. Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
Select Language Main Page Model SyncMaster 570DX Safety Instructions Introduction Connections Installing the Stand KIT Connecting the LCD Display Using the Software Adjusting the LCD Display Troubleshooting Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Connecting the LCD Display Using a Power cord with Earth In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note • AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display.
3) Connect the audio cable for your LCD Display to the audio port on the back of your computer. Note • Turn on both your computer and the LCD Display. Note • The DVI cable or BNC cable is optional. Contact a local Samsung Electronics Service Center to buy optional items. Connecting Digital DVD Note • Input devices such as digital DVD are connected to the DVI IN terminal of the monitor using the DVI cable. • Then, start the DVD with a DVD disc inserted. • Select Digital using the SOURCE button.
1) AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [S-VIDEO] of the LCD Display using an S-VHS or BNC cable. 2) Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the LCD Display 's AV AUDIO IN [L-AUDIO-R] using audio cables. Note • Select AV or S-Video for a connected VCR or Camcorder using the SOURCE button on the front of the LCD Display or on the remote control. • Then, start the VCR or Camcorders with a tape inserted.
Connecting a Camcorder 1) Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display. 2) Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display. Note • Select AV for the Camcorder connection using the SOURCE button on the front of the LCD Display or on the remote control.
Note • Select Component for the connection to a DTV Set Top Box using the SOURCE button on the front of the LCD Display or on the remote control. Note • For an explanation of Component video, see your Set Top Box owner's manual. Connecting Speakers Note • Fasten the SET and the speaker using the screws. * Mount the speaker set without the speaker stand.
Note • Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and the AUDIO OUT [L-AUDIO-R] on LCD Display. Connecting to a Wired Remote Control Note • You can control your monitor by allowing it to receive the remote control signals of other devices through the REMOTE OUT terminal. • You can control a device by allowing it to receive remote control signals from other devices through the REMOTE IN terminal.
Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Select Button Remocon Info Grid Safety Lock Display Selection Port Selection Control Tools 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4. The setting for the PC Serial Port can change. The original value is COM1. 5.
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 4. The selected port is stored in the program and used for the next program as well. Power Control 1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display.
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display. When selecting one set at a time, turn on the Mute function for the selected set.
Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) AV - Changes the Input Source of the selected display to AV. 6) S-Video - Changes the Input Source of the selected display to S-Video.
Info Grid shows some basic information necessary to Image Size Control. 1) ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI. 5) PC Source - When you click Image Size, the PC Source tab first appear. - The Image Size Control button controls Image Size available for PC, BNC, DVI.
Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component. , DVI(HDCP). Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source. 3) Switch Image Size of the selected display randomly.
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display. 4) Shows the On Time settings. 5) Shows the Off Time settings.
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small. 5) Double 1 - Turns on the PIP of the selected display and changes the size to Double 1.
• PIP S-Video Mode Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) TV -Changes the source of the PIP of the selected display to TV.
6) AV - Changes the source of the PIP of the selected display to AV. 7) S-Video - Changes the source of the PIP of the selected display to S-Video. 8) Component - Changes the source of the PIP of the selected display to Component. 9) Channel - Channel arrow appears when the PIP Source is TV. Note: Some of the PIP Sources may not be available for selection, depending on the input source type of the Main Screen. The Input source of MagicNet works only on MagicNet model.
- Adjusts Tint of the selected display. - Available only for NT. 7) Color Tone - Adjusts the Color Tone for the selected display. 8) Color Temp - Adjusts the Color Temp for the selected display. 9) Brightness Sensor - Adjusts the Brightness Sensor for the selected display. 10) Dynamic Contrast - Adjusts the Dynamic Contrast for the selected display. The Input source of MagicNet works only on MagicNet model. Color Temp is only enabled if the Color Tone is set to Off.
- Adjusts green Color of the selected display. - Available only for NT. 6) Blue - Adjusts blue Color of the selected display. - Available only for NT. 7) Color Tone - Adjusts the Color Tone for the selected display. 8) Color Temp - Adjusts the Color Temp for the selected display. 9) Brightness Sensor - Adjusts the Brightness Sensor for the selected display. The Input source of MagicNet works only on MagicNet model. The Input source of TV works only on TV model.
- SRS TS XT Sound ON/OFF of the selected display. 6) Sound Select - Select either Main or Sub when PIP is On. The Input source of MagicNet works only on MagicNet model. The Input source of TV works only on TV model. This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed. Settings Image Lock 1. Click Settings of the main icons and the Settings Control screen appears.
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen. An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control.
1) Safety Screen - Eliminates the afterimages that can result when the selected display stays in Pause mode for an extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and "Second" by second. It can be set to Scroll, Pixel, Bar and Eraser by Screen Type. The Input source of MagicNet works only on MagicNet model. The Input source of TV works only on TV model.
1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection. z The place will be set up by pressing a number in the selected mode.
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 16 . (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 16 . 2. The display you wish to control does not appear on the other Control Info Grids - Check to see if the display power is ON.
Select Language Main Page Model SyncMaster 570DX Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Input Picture [PC / BNC /DVI Mode] Picture [AV / S-Video / Component / DVI-Video Mode] Sound Setup Multi Control Direct Functions The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
PIP When external AV devices such as VCRs or DVDs are connected to the LCD Display , PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off/On) Note • More than one PIP cannot be overlapped on screen as BNC and the component use the same terminal. 1) PIP [MENU] → [ENTER] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] Turns the PIP Screen Off/On. - Off - On [The direct button on the remote control is the 'PIP' button.
5) S-Video 6) Component Picture [PC / BNC /DVI Mode] Available Modes PC / BNC / DVI AV S-Video Component DVI-Video MagicBright™ [MENU] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom. Each mode has its own pre-configured brightness value.
1) Contrast Adjusts the Contrast. 2) Brightness Adjusts the Brightness. Note • By adjusting the picture using the Custom function, MagicBright will change to Custom mode. Color Tone [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] The color tones can be changed. 1) Off 2) Cool 3) Normal 4) Warm 5) Custom (Available in PC, BNC mode only) Note • If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is disabled.
Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. (Available in PC, BNC mode only) 1) Coarse [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [ENTER] → [< / >] → [ENTER] Removes noise such as vertical stripes. Coarse adjustment may move the screen image area.
The Size can be switched. 1) 16:9 2) 4:3 PIP Picture [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [< / >] → [ENTER] Adjusts the PIP Screen Settings. 1) Contrast Adjusts the Contrast of the PIP window on the screen. 2) Brightness Adjusts the Brightness of the PIP window on the screen. 3) Sharpness Adjusts the difference between the lightest and darkest areas of the PIP window. 4) Color Adjusts the Color of the PIP window on the screen.
1) Dynamic 2) Standard 3) Movie 4) Custom [The direct button on the remote control is the 'P.MODE' button.] Custom [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [< / >] → [ENTER] By using the on-screen menus, the contrast and brightness can be changed to your personal preference. 1) Contrast Adds a natural tone to the PIP window. 2) Brightness Adjusts the Brightness. 3) Sharpness Adjusts the picture Sharpness. 4) Color Adjusts the picture Color.
Brightness Sensor [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [< / >] → [ENTER] Brightness Sensor is to automatically detect distribution of inputted visual signal and adjust to create optimum brightness. 1) Off 2) On Dynamic Contrast [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨]→ [ENTER] Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast.
Sound Available Modes PC / BNC / DVI AV S-Video Component DVI-Video Mode [MENU] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] The LCD Display has a built-in high fidelity stereo amplifier. 1) Standard Selects Standard for the standard factory settings. 2) Music Selects Music when watching music videos or concerts. 3) Movie Selects Movie when viewing movies. 4) Speech Selects Speech when watching a show that is mostly dialogue (i.e., news).
Auto Volume [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] Reduces the difference in volume control between broadcasters. 1) Off 2) On SRS TS XT [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers.
DVI-Video Language [MENU] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] You can choose from 11 languages. Note • The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. 1) Clock Set [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [ENTER] → [< / >] → [ENTER] Current Time Setting.
[MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [MENU] The picture parameters are replaced with the factory default values. 1) On 2) Off Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. When the Video Wall is on, you can adjust the Video Wall screen setting.
2) Interval [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨]→ [ENTER] →[∧ / ∨] → [ENTER] Determines the time interval to run the Screen Scroll operation. (1~10 Hour) The time is calculated on the basis of the power on time. By default, the time is set to 10 hours. - 1~10 Hour 3) Second [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨]→ [ENTER] → [∧ / ∨] → [ENTER] Determines the time period to run the Screen Scroll operation. (1~5 Second) By default, the time is set to 5 seconds.
[MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨]→ [ENTER] Adjusts the DVI Source. 1) PC DVI Selects PC DVI mode. 2) DTV DVI Selects DTV DVI mode. FAN [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨]→ [ENTER] Adjusts the FAN. 1) Normal 2) Pivot Note • When pivoting your monitor, make sure to select PIVOT for the FAN. Reset The picture parameters are replaced with the factory default values. For the DVI source, the Reset function is only available when PC DVI is being used.
Available Modes PC / BNC / DVI AV S-Video Component DVI-Video Multi Control Assigns an individual ID to the SET. 1) ID Setup [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [ENTER] → [0~9] Assigns distinctive IDs to the SET. 2) ID Input [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [ENTER] → [0~9] Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.
It will be unlocked. Note • When setting the Lock function, you can only operate the power and lock buttons on the remote control and set. The preset password on the LCD Display is "0000". Note • Resetting the password for the function key lock. Press MUTE → 1 → 8 → 6 → On. The password will be reset to '0000'. The remote control is required for resetting the password. © 1995~2007 SAMSUNG.
Select Language Main Page Model SyncMaster 570DX Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Self-Test Feature Check Check List Q&A Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend that a Samsung cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.
(Refer to Connecting a Computer) Problems related to the Screen Note • Problems related to the LCD Display screen and their solutions are listed. Problems The screen is blank and the power Solutions z Ensure that the power cord is firmly connected and the LCD LCD Display is on. indicator is off. (Refer to the Connecting the LCD Display ) "Check Signal Cable" message. z Ensure that the signal cable is firmly connected to the PC or video sources.
• Problems related to audio signals and their solutions are listed below. Problems No sound. Solutions z Ensure that the audio cable is firmly connected to both the audio-in port on your LCD Display and the audio-out port on your sound card. (Refer to the Connecting the LCD Display ) The sound level is too low. z Check the volume level. z Check the volume level.
Select Language Main Page Model SyncMaster 570DX Safety Instructions Introduction Connections Using the Software Adjusting the Monitor Troubleshooting Specifications General PowerSaver Preset Timing Modes The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
PC Audio Input 3.5 Ø Stereo Jack, 0.5 Vrms (-9 dB) Frequency RF: 80 Hz ~ 15 kHz (at -3 dB) Response A/V: 80 Hz ~ 20 kHz (at -3 dB) Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 640 x 480 43.269 85.008 36.000 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 800 x 600 53.674 85.000 56.250 +/+ VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.
Select Language Main Page Model SyncMaster 570DX Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information For Better Display PRODUCT INFORMATION (Image Retention Free) The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Power Off, Screen Saver, or Power Save Mode z Turn the power off for 4 hours after 20 hours in use z Turn the power off for 2 hours after 12 hours in use z Set the Monitor to power off with the PC Display Properties Power Scheme. z Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Change the Color Information periodically Note • Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes.
z Every 30 minutes, change the characters with movement. z All area display Moving image together with Logo periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use. z The best way to protect your monitor from Image retention is to turn Power off, or set your PC, or System to operate a Screen Saver program when you are not using it. Also Warranty service will be limited based on instruction guide.
- Select method . Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Bar . Time Interval : 1 ~ 10 hours ( Recommend : 1 ) . Time Period : 10 ~ 50 second ( Recommend : 50 ) Note • ( Please check CD's User Guide at "OSD Function", some model's will not available. ) Apply the Screen Erasing function on Product z Apply the Screen Erasing function - Symptom: 2 Vertical blocks move with erasing the display - Select method . Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser .
Select Language Main Page Model SyncMaster 570DX Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix Contact SAMSUNG WORLDWIDE Terms Correct Disposal Authority The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(7267864) (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805-121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.samsung.com/nl NORWAY 815-56 480 http://www.samsung.
Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) 800SAMSUNG (7267864) U.A.E 8000-4726 http://www.samsung.com/za http://www.samsung.com/mea Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the LCD Display. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency.
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household waste at the end of its working life. To prevent possible harm to the environment or damage to health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources.