User Manual U*H75* U*H85* The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. The contents of this manual are subject to change without notice to improve quality. © Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Table of contents Before Using the Product Securing the Installation Space Precautions for storage 4 4 Safety Precautions Symbols Cleaning Electricity and Safety Installation Operation 4 4 5 5 6 7 Preparations Parts 10 Control Panel 10 Direct Key guide 11 Function Key Guide 12 Configuring Eye Saver Mode, Brightness and Contrast from the Initial Screen 14 Changing the Volume setting 14 Reverse Side 15 Adjusting the Product Tilt and Height 16 Rotating the Monitor Screen (U32H850UM*) 16 Rotating the monito
Table of contents Picture Size 40 Contrast 41 Adjusting OSD (On Screen Display) settings Transparency 42 Language 42 Display Time 42 Installing the Software Specifications Easy Setting Box 48 Restrictions and Problems with the Installation 48 System Requirements 48 General 52 Standard Signal Mode Table 53 Requirements Before Contacting Samsung Customer Service Center 49 Testing the Product 49 Checking the Resolution and Frequency 49 Check the following.
Chapter 01 Before Using the Product Securing the Installation Space Precautions for storage Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product. ――The exterior may differ depending on the product. ――Contact your nearest Samsung Customer Service Center if you want to clean the inside of the product (Service fee will be charged.
Cleaning ――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ――Take the following steps when cleaning. Electricity and Safety Warning 1 Power off the product and computer. •• Do not use a damaged power cord or plug, or a loose power socket. 2 Disconnect the power cord from the product. •• Do not use multiple products with a single power socket. ――Hold the power cable by the plug and do not touch the cable with wet hands.
Installation Warning Caution •• DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. •• Do not drop the product while moving. •• Do not install the product in poorly ventilated spaces such as a bookcase or closet. •• Install the product at least 10 cm away from the wall to allow ventilation. •• Keep the plastic packaging out of the reach of children. ‒‒ Children may suffocate.
Operation Warning •• There is a high voltage inside the product. Never disassemble, repair or modify the product yourself. ‒‒ Contact Samsung Customer Service Center for repairs. •• To move the product, first disconnect all the cables from it, including the power cable. •• If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer Service Center.
Caution •• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. ‒‒ Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time. •• Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc). ‒‒ Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
•• Do not hold the product upside-down or move it by holding the stand. ‒‒ The product may fall and become damaged or cause an injury. •• Looking at the screen too close for an extended period of time can deteriorate your eyesight. •• Do not use humidifiers or stoves around the product. •• Rest your eyes for more than 5 minutes or look at distance objects for every 1 hour of product use. •• Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.
Chapter 02 Preparations Parts Icons Description JOG Button Multi directional button that helps navigate. ――The JOG button is located on the rear left side of the product. The button can be used to move up, down, left or right, or as Enter. Control Panel This LED is power status indicator and works as ――The color and shape of parts may differ from what is shown. Specifications are subject to change without •• Power On (Power button): Off notice to improve quality.
Direct Key guide ――The shortcut button screen (OSD menu) shown below is displayed only when the monitor screen is turned on, the computer resolution changes, or the input source changes. Eye Saver Mode Volume Features Eye Saver Mode Off •• UP/DOWN: Adjust Brightness, Contrast, Eye Saver Mode. •• LEFT/RIGHT: Adjust Volume. •• PRESS(ENTER): Display Function Key Guide.
Function Key Guide ――To enter the main menu or to use other items, press the JOG button to display the Function Key Guide. You can exit by pressing the JOG button again. UP/DOWN/LEFT/RIGHT: Move to the item you want. The description for each item will appear when the focus changes. PRESS(ENTER): The selected item will be applied. Return Icons Description Selects to change the input signal by moving the JOG button in the Function Key Guide screen.
When the monitor displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for control source and power could be used as below. JOG Button Power saving/Non-signal mode UP Source Change Down PRESS(ENTER) for 2 seconds Power Off When the monitor displays the Main menu the JOG Button could be used as below. JOG Button Action UP/DOWN Move the option Exit the Main menu. LEFT Close Sublist without saving value. Value decreases in the slider. RIGHT PRESS(ENTER) Move to next depth.
Configuring Eye Saver Mode, Brightness and Contrast from the Initial Screen Adjust the Brightness, Contrast and Eye Saver Mode by moving the JOG button. Changing the Volume setting You can adjust Volume by moving the JOG button left or right, if no OSD menu is displayed. 50 Volume Mute Contrast Off Eye Saver Mode ――The displayed image may differ depending on the model.
Reverse Side ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Refer to the actual product. Port Description HDMI IN 1 HDMI IN 2 Port Description Connects to a source device using an HDMI cable or HDMI-DVI cable. Connect the power cord for your monitor to the POWER IN port on the back of the product.
Adjusting the Product Tilt and Height Rotating the Monitor Screen (U32H850UM*) ――The color and shape of parts may differ from what is shown. Specifications are subject to change without ――You can rotate your monitor as shown below. ――The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. notice to improve quality. U28H750UQ* -1.0° (-2.0°, +1.0°) ~ 20.0° (±2.0°) 1 2 3 4 5 6 U32H850UM* -5.0° (±2.0°) ~ 24.0° (±2.0°) -30.
Rotating the monitor (U32H850UM*) Anti-theft Lock When rotating the monitor, the rotation angle is displayed on the monitor screen. ――An anti-theft lock allows you to use the product securely even in public places. ――The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
Precautions for moving the monitor •• Do not directly apply pressure on the screen. •• Do not hold the screen when moving the monitor. •• Hold the lower corners or edges of the monitor when moving it. •• Do not hold the product upside down only by the stand.
MagicRotation Auto (U32H850UM*) The MagicRotation Auto function detects the rotation of monitors that are fitted with a rotation sensor and rotates the Windows screen accordingly. Software Installation 1 Insert the user manual CD provided with the product into the CD-ROM drive. 2 Follow the instructions given on the screen to proceed with installation. ――After installation, the application menu language will be displayed in the language of the operating system.
Installing a Wall-mount Kit or Desktop Stand (U28H750UQ*) ――Power the product off and remove the power cable from the power socket. 1 2 •• Notes ‒‒ Using a screw longer than the standard length can damage the internal components of the product. ‒‒ The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications. ‒‒ Do not use screws that do not comply with the VESA standards.
Installing a Wall-mount Kit or Desktop Stand (U32H850UM*) ――Power the product off and remove the power cable from the power socket. 1 2 •• Notes ‒‒ Using a screw longer than the standard length can damage the internal components of the product. ‒‒ The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications. ‒‒ Do not use screws that do not comply with the VESA standards.
Installation Attaching the Stand (U28H750UQ*) ――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. ――The exterior may differ depending on the product. 1 Insert the stand neck into the stand base in the direction shown in the figure. 2 Check that the stand neck is firmly connected. 3 Tightly fasten the connecting screw at the bottom of the stand base.
Attaching the Stand (U32H850UM*) ――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. ――The exterior may differ depending on the product. 1 Insert the stand neck into the stand base in the direction shown in the figure. 2 Check that the stand neck is firmly connected. 3 Tightly fasten the connecting screw at the bottom of the stand base.
Removing the Stand (U28H750UQ*) ――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. ――The exterior may differ depending on the product. 1 Place the protective Styrofoam (cushion) included in the package on the floor and place the product facing down on the Styrofoam, as shown in the image.
Removing the Stand (U32H850UM*) ――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. ――The exterior may differ depending on the product. 1 Place the protective Styrofoam (cushion) included in the package on the floor and place the product facing down on the Styrofoam, as shown in the image. 2 Push the key upward and hold. Turn the stand neck of the display counterclockwise for 10°.
Chapter 03 Connecting and Using a Source Device Read below before installing the monitor. Connecting and Using a PC 1 Check the shapes of both ends of the cables that came with the monitor, and check the shapes and Select a connection method suitable for your PC. 2 Before connecting signal cables, disconnect the power cables for the monitor and external devices ――Provided ports may vary depending on the product.
Connection Using the HDMI-DVI Cable Check to make sure that the power cables for the monitor and external devices, such as computers and set-top boxes, are not connected to the power outlet. HDMI IN 1, HDMI IN 2 Connection Using the MINI DP Cable (U32H850UM*) Check to make sure that the power cables for the monitor and external devices, such as computers and set-top boxes, are not connected to the power outlet.
Connecting the Product to a PC as a USB HUB (U32H850UM*) Connecting a PC to the Product Utilizing the Product as a USB HUB Using the product as a hub, connect and use various source devices with the product at the same time. A PC cannot connect to multiple source devices at the same time as it has a limited number of input/ output ports available.
――To detect and start a USB device faster, connect the device to the USB 3.0 port on the product. The read/ write rate will be affected by the USB device and your PC. ――The product does not support media play. If you need to play a file in your USB device, please connect the product as a Hub to your PC and play the file on your PC. ――For USB-related problems caused by OS, drive programs or software, please contact relevant suppliers.
Tidying Up the Connected Cables (U28H750UQ*) 1 Connect cables to the appropriate ports. 2 Grab the stand with one hand and use your other hand to close the COVERREAR SUB in the direction of the arrow. 3 The cables are now tidied up. 4 Grab the stand with one hand and use the thumb on your other hand to remove the COVER-REAR SUB in the direction of the arrow.
Tidying Up the Connected Cables (U32H850UM*) 1 Stand assembly is complete. 6 Open the COVER-STAND NECK LEFT, and rotate the open part at the bottom. 2 Rotate the machine to the highest vertical position. 7 Place the corresponding cables into the stand-neck holder. Do not stretch the line. Three cables in one holder is recommended. 3 Connect the corresponding cables. 8 Cover the COVER-STAND NECK LEFT.
Correct posture to use the product Driver Installation ――You can set the optimum resolution and frequency for this product by installing the corresponding drivers. ――To install the latest version of the product driver, download it from the Samsung Electronics website at http://www.samsung.com. Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase.
Chapter 04 Screen Setup Configure the screen settings such as brightness. A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. In PC mode •• Custom: Customize the contrast and brightness as required.
Black Equalizer Contrast Adjust the brightness of the dark areas. Adjust the contrast between the objects and background. (Range: 0~100) As the value gets closer to 1, the darker areas of the screen become brighter, making it easier to find enemies when playing a game. To find enemies more easily during a game, use a lower value. A higher value will increase the contrast to make the object appear clearer.
Color SAMSUNG MAGIC Angle (U28H750UQ*) Adjust the tint of the screen. MAGICAngle allows you to configure the settings to obtain the optimum picture quality according to your viewing angle. SAMSUNG ――This menu is not available when SAMSUNG Bright is set to Cinema, Dynamic Contrast or Basic Color mode. MAGIC ――This menu is not available when Game Mode is enabled. ――This menu is not available when Eye Saver Mode is enabled. ――The Color Tone and Gamma menu is not available when SAMSUNGAngle is enabled.
HDMI Black Level Game Mode If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/ color degradation, black level, etc.) may occur, depending on the connected source device. In such case, HDMI Black Level can be used to adjust the image quality. Configure the product screen settings for game mode. If this is the case, correct the degraded picture quality using HDMI Black Level. ――This option is not available when SAMSUNG Bright is in Basic Color mode.
Picture Size Screen Adjustment Change the picture size. ――This menu is only available when Picture Size is set to Screen Fit in AV Mode. ――This menu is not available when PIP/PBP Mode is set to On and the Size is set to ――This option is not available when FreeSync is enabled. (PBP Mode). When a 480P or 576P or 720P or 1080P signal is input in AV mode and the monitor can display normally, select Screen Fit to adjust horizontal position in 0-6 levels.
Chapter 05 Configuring the PIP/PBP Settings A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. ――PIP/PBP mode is compatible with Windows 7, Windows 8, and Windows 10. ――The PIP/PBP function may not be available depending on the specifications of the graphics card used.
Size Sound Source Select the size and aspect ratio of the sub-screen. Set which screen you want to hear the sound for. •• : Select the icon image if you want to use PBP mode where the optimum resolution for the left and right sides of the screen is 1920 x 2160 (width x height). •• : Select the icon image if you want to use PIP mode where the optimum resolution for the subscreen is 720 x 480 (width x height).
Source Picture Size Select the source for each screen. Due to DisplayPort and MiniDP can't be identified at the same time, if DisplayPort and MiniDP as the source at the same time ,the 'Apply' is not available. PIP Mode (available in PIP mode (Size / / )) Select the image size for sub-screen. PIP Mode (available in PIP mode(Size / / )) In PC mode ――The input source for the main screen changes. •• Auto: Display the picture according to the aspect ratio of the each screen input source.
PBP Mode (available in PBP mode(Size )) Contrast Set the Picture Size for each of the divided screens. In PC mode •• Auto: Display the picture according to the aspect ratio of the each screen input source. •• Wide: Display the picture in full screen regardless of the aspect ratio of the each screen input source. In AV mode •• 4:3: Display the picture of the sub-screen with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
Chapter 06 Adjusting OSD (On Screen Display) settings A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Language Set the menu language. Transparency ――A change to the language setting will only be applied to the onscreen menu display.
Chapter 07 Setup and Reset A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. FreeSync •• Off: Disable FreeSync. •• Standard Engine: Enable the basic FreeSync functions of the AMD graphics card.
The models in the Graphic Cards list supports FreeSync FreeSync can only be used with specific AMD graphics card models. Refer to the following list for supported graphics cards: Make sure to install the latest official graphics drivers from AMD that support FreeSync. ――For additional AMD graphics card models that support the FreeSync feature, visit the official AMD website. ――Select FreeSync Off if you are using a graphics card from a different manufacturer.
Eco Saving Plus The Eco Saving Plus function reduces power consumption by controlling the electric current used by the monitor panel. ――This option is not available when SAMSUNG Bright is in Dynamic Contrast mode. MAGIC Configuring Eco Timer Eco Timer: Turn on Eco Timer mode. Eco Off After: The Eco Timer can be set between 10 and 180 minutes. The product will automatically power off after the specified time has elapsed. ――This option is only available when Eco Timer is set to On.
PC/AV Mode Key Repeat Time Set PC/AV Mode to AV. The picture size will be enlarged. Control the response rate of a button when the button is pressed. This option is useful when you view a movie. Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds only once when a button is pressed. •• Set to PC when connected to a PC. •• Set to AV when connected to an AV device. ――Supplied for the wide models only such as 16:9 or 16:10.
Information View the current input source, frequency and resolution.
Chapter 08 Installing the Software Easy Setting Box System Requirements OS Easy Setting Box enables users to use the monitor by partitioning multiple sections. To install the latest version of Easy Setting Box, download it from the Samsung Electronics website at http://www.samsung.com. ――The software may not work properly if you do not restart the computer after the installation.
Chapter 09 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center ――Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check the following. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connectors are locked.
Not Optimum Mode is displayed. Video playback is choppy. This message appears when the signal from the graphics card exceeds the maximum resolution or frequency for the product. Playback of high-definition large video files can be choppy. This may be because the video player is not optimized for the computer resource. Change the maximum resolution and frequency to suit the product performance, referring to Standard Signal Mode Table (P.53). Try playing the file on another video player.
Q&A ――Refer to the user manual for your PC or graphics card for further instructions on adjustment. How can I change the frequency? Set the frequency on your graphics card. •• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings → Advanced → Monitor, and adjust Refresh rate under Monitor settings. •• Windows ME/2000: Go to Control Panel → Display → Settings → Advanced → Monitor, and adjust Refresh rate under Monitor settings.
Chapter 10 Specifications General Model Name U28H750UQ* U32H850UM* Size 28 Class (27.9 Inches / 70.8 cm) 32 Class (31.5 Inches / 80.1 cm) Display area 620.93 mm (H) x 341.28 mm (V) 698.4 mm (H) x 392.85 mm (V) 24.4 Inches (H) x 13.4 Inches (V) 27.5 Inches (H) x 15.5 Inches (V) 0.16 mm (H) x 0.16 mm (V) 0.181 mm (H) x 0.181 mm (V) 0.006299 Inches (H) x 0.006299 Inches (V) 0.007126 Inches (H) x 0.007126 Inches (V) 533.25 MHz (DisplayPort) 297.00 MHz (HDMI1) 533.
Standard Signal Mode Table Model Name Synchronization Resolution U28H750UQ* U32H850UM* Horizontal Frequency 30 – 135 kHz 30 – 135 kHz Vertical Frequency 56 – 75 Hz (DisplayPort) 56 – 75 Hz (DisplayPort/MINI DisplayPort) 24 – 75 Hz (HDMI1/HDMI2) 24 – 75 Hz (HDMI1/HDMI2) 3840 x 2160 @ 60 Hz (DisplayPort) 3840 x 2160 @ 60 Hz (DisplayPort/MINI DisplayPort) 3840 x 2160 @ 30 Hz (HDMI1) 3840 x 2160 @ 30 Hz (HDMI1) 3840 x 2160 @ 60 Hz (HDMI2) 3840 x 2160 @ 60 Hz (HDMI2) 3840 x 2160 @ 60 Hz (Displa
Displayport/MINI DisplayPort Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 1152 x 870 68.681 75.062 100.000 -/+/+ VESA, 1280 x 720 45.000 60.000 74.250 VESA, 1280 x 800 49.702 59.810 83.500 -/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900 60.000 60.000 108.000 +/+ VESA, 1680 x 1050 65.290 59.954 146.
HDMI1 Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1280 x 800 49.702 59.810 83.500 -/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900 60.000 60.000 108.000 +/+ VESA, 1680 x 1050 65.290 59.954 146.250 -/+ VESA, 1920 x 1080 67.500 60.000 148.500 +/+ VESA, 2560 x 1440 88.787 59.951 241.
HDMI2 Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900 60.000 60.000 108.000 +/+ VESA, 1680 x 1050 65.290 59.954 146.250 -/+ VESA, 1920 x 1080 67.500 60.000 148.500 +/+ VESA, 2560 x 1440 88.787 59.951 241.500 +/- CEA, 3840 x 2160 135.000 60.000 594.
Chapter 11 Appendix Responsibility for the Pay Service (Cost to Customers) A Product damage caused by customer's fault ――When the service is requested, in spite of in warranty, we may charge you for a visit from a service •• External impact or drop. technician in the following cases. Not a product defect Cleaning of the product, Adjustment, Explanation, Re-installation and etc. •• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.