Built-in Trim Kit Installation Instructions MA-TK8020** MA-TK8020_AA_II_DE68-04476A-01_EN.
Contents Before you begin Contents Before you begin 2 Parts included in the kits 3 Tools needed 3 Installation 4 Read these instructions completely and carefully. IMPORTANT • Save these instructions for local inspector’s use. • Observe all governing codes and coordinates. • Be sure to disconnect the plug of the microwave oven from the electrical outlet before installing the Builtin Kit. Remove the turntable from the oven cavity.
Parts included in the kits Tools needed Duct Base (1 EA) Duct Side (1 EA) Duct Rear (1 EA) Install Bracket (2 EA) Install hook Screw A (5/8” length) (12 EA) Screw B (15/32” length) (4 EA) Screw C (25/64” length) (9 EA) Pencil Drill with 7/64 or #35 Drill bit Scissors Tape measure T15H Torx driver Parts included in the kits Trim Frame (1 EA) Screwdriver Template (1 EA) English 3 MA-TK8020_AA_II_DE68-04476A-01_EN.
Installation STEP 2 STEP 1 CUTOUT DIMENSIONS Width Depth 3" min Electric Heat Source Model Height Height 16 3/4" ± 1/16" Width 25 1/2" ± 1/16" Depth 21 1/2" ± 1/16" P5 A CENTER LINE A P6 P7 C P8 TRIM DIMENSIONS Height 20 1/16" ± 1/64" Width 29 3/4" ± 1/64" Depth 1 1/4" ± 1/64" D P2 TRIM WEIGHT Net Weight C P1 13.
4. Tight 2 screws together on the Install hook by using provided SCREW A. (2 EA) STEP 4 1. Place oven on the Duct Base. NOTE You may not be assembled when using the thicker Drill bit. Duct Base STEP 3 5. Remove 4 screws from the lower right and left side of outer panel. 2. Tight 2 screws together on the back side with Duct base by using provided SCREW C. (2 EA) 3. Tight 2 screws together on the right side with Duct base by using provided SCREW C.
Installation 4. Tight 4 screws to Duct base and Duct side on the left side by using provided SCREW C. (4 EA) STEP 5 Check the assembly between Install hook and Duct base. Duct Side 5. Remove 2 Screw C on top of the back. In addition, Remove 1 Torx Screw to use Torx driver on bottom of the back. Do not scrap Screw. (3 EA) 1. Slide the oven with Duct Base into cabinet until Duct Base touch the front of cabinet. 2. Plug the Power cord into the electrical outlet. 3.
5. Tight Install Bracket 4 holes by using provided SCREW A. (4 EA) 2. Open the oven door. Tight 4 screws Trim frame by using provided SCREW B. (4 EA) STEP 6 1. Press the Trim Frame into the opening until all sides snap into place. Top Trim Frame Bottom Installation English 7 MA-TK8020_AA_II_DE68-04476A-01_EN.
DE68-04476A-01 MA-TK8020_AA_II_DE68-04476A-01_EN.
Kit de marco embellecedor para empotrar Instrucciones de instalación MA-TK8020** MA-TK8020_AA_II_DE68-04476A-01_MES.
Contenido ANTES DE COMENZAR Lea estas instrucciones con detenimiento en su totalidad. Contenido ANTES DE COMENZAR 2 Piezas incluidas en los kits 3 • Conserve estas instrucciones para que puedan ser consultadas por el inspector de su localidad. Herramientas necesarias 3 • Cumpla todos los códigos y coordenadas exigidos por las autoridades pertinentes. Instalación 4 • Asegúrese de desconectar el enchufe del horno de microondas del tomacorriente antes de instalar el kit para empotrar.
Piezas incluidas en los kits Marco embellecedor (1 ud.) Conducto base (1 ud.) Herramientas necesarias Destornillador Lápiz Perfore con mecha de 7/64 o #35. Tijeras Cinta de Medir Destornillador Torx T15H Conducto lateral (1 ud.) Ménsula de instalación (2 uds.) Gancho de instalación Tornillo A (5/8” largo) (12 uds.) Tornillo B (15/32” largo) (4 uds.) Tornillo C (25/64” largo) (9 uds.) Piezas incluidas en los kits Conducto posterior (1 ud.) Plantilla (1 ud.
Instalación PASO 2 STEP 1 DIMENSIONES DE LA ABERTURA RECORTADA Ancho Profundidad 3” mín.
4. Ajuste 2 tornillos en el gancho de instalación; use los TORNILLOS A (2 uds.) provistos. PASO 4 1. Coloque el horno en el conducto base. NOTA Si la mecha es más gruesa, es posible que no pueda instalarlo. Conducto base PASO 3 5. Quite 4 tornillos del lado inferior derecho e izquierdo del panel exterior. 2. Ajuste 2 tornillos en el lado trasero con el conducto base; use los TORNILLOS C (2 uds.) provistos. 3. Ajuste 2 tornillos en el lado derecho con el conducto base; use los TORNILLOS C (2 uds.
Instalación Conducto lateral 4. Ajuste 4 tornillos en el conducto base y el conducto lateral por el lado izquierdo; use los TORNILLOS C (4 uds.) provistos. PASO 5 Verifique el conjunto entre el gancho de instalación y el conducto base. 5. Quite 2 tornillos C de la parte superior trasera. Además, quite 1 tornillo Torx con el destornillador Torx de la parte inferior trasera. No deseche los tornillos (3 uds.). 1.
5. Ajuste los 4 agujeros de la ménsula de instalación; use los TORNILLOS A (4 uds.) provistos. 2. Abra la puerta del horno. Ajuste los 4 tornillos del marco embellecedor; use los TORNILLOS B (4 uds.) provistos. STEP 6 1. Presione el marco embellecedor en la abertura hasta que los lados encajen en su lugar. Superior Marco embellecedor Inferior Instalación Español 7 MA-TK8020_AA_II_DE68-04476A-01_MES.
DE68-04476A-01 MA-TK8020_AA_II_DE68-04476A-01_MES.