SyncMaster 710T / 910T / 710N / 910N / 510T / 510N / 512N / 515V / 915V / 712N / 912N / 711T / 912T / 913N / 701T
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended periods of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. z This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. z This may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. z This may cause a fire.
Set down the monitor carefully. z It could be damaged or broken. Do not place the monitor face down. z The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. z z Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. Leave a space for ventilation between the product and the wall. z Poor ventilation may cause the interior temperature to rise and lead to a fire.
Contact a Service Center or Customer Center for interior cleaning once a year. z Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or a fire. Other Do not remove cover (or back). No user serviceable parts inside. z z This may cause an electric shock or a fire. Refer servicing to qualified service personnel.
z This may cause a breakdown, electric shock or a fire due to damage to the cable. Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small metal objects on the monitor. z z This may cause malfunction, an electric shock or a fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center . Do not use or store inflammable substances near the monitor.
Sitting too close to the monitor on a continuous basis may damage eyesight. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not use the monitor where it can be exposed to strong vibrations. z Exposure to strong vibrations can be a fire hazard and shorten the life of the monitor. When moving the monitor, turn the power switch off and unplug the power cord.
SyncMaster 510T / 710T / 910T / 711T / 912T / 701T Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
Quick Setup Guide Warranty Card Dirver, Natural Color software, MagicTune™ software CD (Not available in all locations) Cable D-Sub Cable Power Cord DVI Cable(option) Front 1. Menu button [ ] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. 2. MagicBright button [ ] MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
If this is the case, adjust the Brightness and Contrast by using the OSD menu. 3. Brightness button [ ] 2,3. Adjust buttons [ ] >>Click here to see an animation clip When OSD is not on the screen, Push the button to adjust brightness. Adjust items in the menu. 4. Enter button [ ] / Source button Activate a highlighted menu item. / Push the 'Source', then Selects the Video signal while the OSD is off.
SyncMaster 710T / 910T / 711T / 912T / 701T(Option) (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. 3. DVI port D-sub 15-pin port 4. Power on/off Switch (option) Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI Port on the back of your Monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Use this button for turn the monitor on and off.
SyncMaster 510N / 710N / 910N / 512N / 712N / 912N / 913N / 515V / 915V Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
Quick Setup Guide Warranty Card Dirver, Natural Color software, MagicTune™ software CD (Not available in all locations) Cable D-Sub Cable Power Cord Front 1. Menu button [ ] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. 2. MagicBright button [ ] MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain.
If this is the case, adjust the Brightness and Contrast by using the OSD menu. 3. Brightness button [ ] 2,3. Adjust buttons [ ] >>Click here to see an animation clip When OSD is not on the screen, Push the button to adjust brightness. Adjust items in the menu. 4. Enter button [ ] Activate a highlighted menu item. 5. Auto button Use this button for auto adjustment direct access. 6. Power button Use this button for turn the monitor on and off. 7.
SyncMaster 510T / 710T / 910T / 711T / 912T / 701T 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor. 2-3. Connected to a Macintosh.
SyncMaster 510N / 710N / 910N / 512N / 712N / 912N / 913N / 515V / 915V 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 2-3.
SyncMaster 510T / 510N / 512N /515V 701T Monitor and Bottom Pivot Stand Attaching a base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
SyncMaster 510T / 510N / 512N / 515V / 701T Simple stand A. Monitor Pivot stand B. Mounting interface pad 1. 2. 3. 4. Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove four screws and then remove the Stand from the LCD monitor. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung.com/. 5. Monitor driver installation is completed. Windows XP | Windows 2000 | Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2.
If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button. Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4.
How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup.exe and then press the key.
SyncMaster 510T / 710T / 910T / 711T / 912T / 701T 1. Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. 2. These buttons allow you to adjust items in the menu. 3. These buttons allow you to adjust items in the menu. 4. Activate a highlighted menu item. 5. Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are adjusted automatically.
Brightness Menu Description Brightness Adjust Brightness. Source Menu Description Source 1. Picture 2. Color 3. Image 4. OSD 5. Setup 6. Information Selects the Video signal while the OSD is off. Brightness Color Tone Coarse Language Auto Source Contrast Color Control Fine H-Position Image Reset Gamma Sharpness V-Position Color Reset H-Position Transparency V-Position Display Time Picture Menu Description Brightness Adjust the Brightness.
OSD Menu Description Language Follow these steps to change the language used in the menu. You can choose one of seven languages. (English, German, Spanish, French, Italian, Swedish, Russian) Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Positon You can change the vertical position where the OSD menu appears on your monitor.
SyncMaster 510N / 710N / 910N / 512N / 712N / 912N / 913N / 515V / 915V 1. Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. 2. These buttons allow you to adjust items in the menu. 3. These buttons allow you to adjust items in the menu. 4. Activate a highlighted menu item. 5. Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are adjusted automatically.
Brightness Menu Description Brightness 1. Picture 2. Color 3. Image 4. OSD 5. Setup 6. Information Adjust Brightness. Brightness Color Tone Coarse Language Image Reset Contrast Color Control Fine H-Position Color Reset Gamma Sharpness V-Position H-Position Transparency V-Position Display Time Picture Menu Description Brightness Adjust the Brightness. Direct Access Feature : When OSD is not on the screen, Push the button to adjust brightness. Contrast Play/Stop Adjust the Contrast.
OSD Menu Description Language Follow these steps to change the language used in the menu. You can choose one of seven languages. (English, German, Spanish, French, Italian, Swedish, Russian) Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Positon You can change the vertical position where the OSD menu appears on your monitor.
Overview | Install | OSD Mode | Color Calibration | Uninstall | Troubleshooting Overview What is MagicTune™? Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls available to tune the image often prove to be challenging.
Overview | Install | OSD Mode | Color Calibration | Uninstall | Troubleshooting Install 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the InstallShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune program. 7. Click "Install." 8. The "Installation Status" window appears.
9. 10. Click "Finish." When the installation is complete, the MagicTune 2.5 executable icon appears on your desktop. Double-click the icon to start the program. Magictune execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. 11. The following window appears if the installation is successful.
12. The following error message indicates that the system is using a video card that is not supported by MagicTune. Installation Problems The installation of MagicTune™ 2.5 can be affected by such factors as the video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation.
Overview | Install | OSD Mode | Color Calibration | Uninstall | Troubleshooting MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z z OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. When Pivot is functioning, part of Magictune Program may not operate normally.
Allows the user to adjust the screen settings to the desired values. i Brightness n j k l m n j Contrast n k l m j Resolution n k l m j MagicBright k l m Brightness Makes the entire screen brighter or darker. The detailed data of the images in the dark areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions. Contrast Adjusts the difference in brightness between the bright and dark areas on screen. Determines the crispness of the images.
n Color Tone m i j k l m n Color Control m j k l n Calibration j k l The tone of the color can be changed. Color Tone z z Color Control Adjusts of the monitor image color. You can change the monitor color to your desired color. z Calibration Warm - Normal - Cool Custom R- G - B The process through which the colors of your choice are optimized and maintained.
i Image Setup n j k l m n j Position k l m z Image Setup z z Position Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. Auto Setup : Auto adjustment allows the monitor to self-adjust to the incoming video signal.
z Preferences z Source Select z z Enable task tray menu . - To access the MagicTune menus, click the icon on the [task tray menu]. The menus are not displayed if the [Enable System Tray] is deselected in [Options] ' [Basic Settings]. Select Language - The language chosen affects only the language of the OSD. Analog Digital Support Tab Definition Shows the Asset ID and the version number of the program, and allows you to use the Help feature.
Overview | Install | OSD Mode | Color Calibration | Uninstall | Troubleshooting Color Calibration 1. Color Calibration Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition . 1. 2. 3. 4. 5.
Press "Preview" button on the Color Calibration. The above picture will be shown. 1. 2. Press "View Calibrated" button to see the calibration effect which you adjusted. Press "View Uncalibrated" button to see the original image.
Overview | Install | OSD Mode | Color Calibration | Uninstall | Troubleshooting Uninstall The MagicTune program can be removed only by using the "Add or Remove Programs" option of the Windows Control Panel. Perform the following steps remove MagicTune. 1. Go to [Tusk Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add or Remove Programs" icon in Control Panel. 3.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Troubleshooting z MagicTune may not work in case monitor is replaced or driver of graphic card is updated while MagicTune is operating. If so, please restart the system. Check when MagicTune does not function properly. * MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and Play.
SyncMaster 510T / 710T / 910T / 711T / 912T / 701T Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
displayed. If the display exceeds 85Hz, the display will work properly but the "Not Optimum Mode","Recommanded Mode 1280 x 1024 60Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode.
changing the video card. Has the video card been set properly? Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have you installed the monitor driver? Install the monitor driver according to the Driver Installation Instructions. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. Install the monitor driver according to the Driver Installation Instructions.
functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
SyncMaster 510N / 710N / 910N / 512N / 712N / 912N / 913N / 515V / 915V Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
(The message is displayed again if the system is rebooted.) The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.Make sure the video card is fully inserted in it's slot.
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel→System→Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center. Q&A Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used.
Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2.
General General Model Name SyncMaster 710T / 711T / 701T LCD Panel Size 17" Diagonal Display area 337.92 (H) x 270.336 (V) Pixel Pitch 0.264mm (H) x 0.264mm (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,194,277 Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Less than 34W Dimensions (WxDxH)/ Weight (Simple Stand) 370.0 x 60.3 x 316.0 mm (Without Stand) 370.0 x 195.4 x 386.5 mm (with Basic Stand) / 4.4kg Dimensions (WxDxH)/ Weight (Pivot Stand) 370.0 x 60.3 x 316.0 mm (Without Stand) 370.0 x 200,0 x 404.0 mm (with Basic Stand) / 5.8kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.
General General Model Name SyncMaster 910T / 912T LCD Panel Size 19" Diagonal Display area 376.32 (H) x 301.056 (V) Pixel Pitch 0.294mm (H) x 0.294mm (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,777,219 Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Less than 38W Dimensions (WxDxH)/ Weight (Simple Stand) 416.6 x 60.2 x 349.4 mm (Without Stand) 416.6 x 215.2 x 424.6 mm(with Basic Stand) / 5.6 kg Dimensions (WxDxH)/ Weight (Pivot Stand) 416.6 x 60.2 x 349.4 mm (Without Stand) 416.6 x 200.0 x 420.6 mm(with Basic Stand) / 7.2 kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
General General Model Name SyncMaster 710N / 712N LCD Panel Size 17" Diagonal Display area 337.92 (H) x 270.336 (V) Pixel Pitch 0.264mm (H) x 0.264mm (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,194,277 Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog 0.7Vp-p Positive at 75 ohms Separate H/V sync, Composite sync, SOG, TTL level positive or negative.
Dimensions (WxDxH)/ Weight (Simple Stand) 370.0 x 60.3 x 316.0 mm (Without Stand) 370.0 x 195.4 x 386.5 mm (with Basic Stand) / 4.4kg Dimensions (WxDxH)/ Weight (Pivot Stand) 370.0 x 60.3 x 316.0 mm (Without Stand) 370.0 x 200.0 x 404.0 mm (with Basic Stand) / 5.8kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
General General Model Name SyncMaster 910N / 912N / 913N / 915V LCD Panel Size 19" Diagonal Display area 376.32 (H) x 301.056 (V) Pixel Pitch 0.294mm (H) x 0.294mm (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16 194 277 Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog 0.
Dimensions (WxDxH)/ Weight (Simple Stand) 416.6 x 60.2 x 349.4 mm (Without Stand) 416.6 x 215.2 x 424.6 mm(with Basic Stand) / 5.6 kg Dimensions (WxDxH)/ Weight (Pivot Stand) 416.6 x 60.2 x 349.4 mm (Without Stand) 416.6 x 200.0 x 420.6 mm(with Basic Stand) / 7.2 kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
General General Model Name SyncMaster 510T LCD Panel Size 15" Diagonal Display area 304.1 (H) x 228.1 (V) Pixel Pitch 0.297 (H) x 0.297 (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 61 kHz Vertical 56 ~ 75 Hz Display Color 16,194,277 Colors Resolution Optimum resolution 1024 x 768@60 Hz Maximum resolution 1024 x 768@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Less than 25W Dimensions (WxDxH)/ Weight 338.0 X 56.3 X 272.0 mm (Without Stand) 338.0 X 195.4 X 342.5 mm (with Basic Stand) / 3.0kg VESA Mounting Interface 75mm x 75mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 800 x 600 35.156 56.250 36.
General General Model Name SyncMaster 510N / 512N LCD Panel Size 15" Diagonal Display area 304.1 (H) x 228.1 (V) Pixel Pitch 0.297 (H) x 0.297 (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 61 kHz Vertical 56 ~ 75 Hz Display Color 16,194,277 Colors Resolution Optimum resolution 1024 x 768@60 Hz Maximum resolution 1024 x 768@75 Hz Input Signal, Terminated RGB Analog 0.7Vp-p Positive at 75 ohms Separate H/V sync, Composite sync, SOG, TTL level positive or negative.
Dimensions (WxDxH)/ Weight 338.0 X 56.3 X 272.0 mm (Without Stand) 338.0 X 195.4 X 342.5 mm (with Basic Stand) / 3.0kg VESA Mounting Interface 75mm x 75mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature: 50°F ~ 104°F(10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4°F ~113°F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 800 x 600 35.156 56.250 36.
Service The address and phone number of the company can be changed without previous notice. AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 1300 362 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc.
Ciencies, 55-65 (Poligono Pedrosa) 08908 Hospitalet de Llobregat (Barcelona) Tel. : (93) 261 67 00 Fax. : (93) 261 67 50 http://samsung.es/ FRANCE : SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2 66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex Tel : 08 25 08 65 65 Fax : 01 48 63 06 38 http://www.samsungservices.com/ GERMANY : TELEPLAN Rhein-Main GmbH Feldstr. 16 64331 Weiterstadt T. 06151/957-1306 F. 06151/957-1732 * EURO 0.12/Min http://www.samsung.
Panama Tel. : (507) 210-1122, 210-1133 Tel : 800-3278(FAST) http://www.samsung-latin.com/ PERU : Servicio Integral Samsung Av.Argentina 1790 Lima1. Peru Tel: 51-1-336-8686 Fax: 51-1-336-8551 http://www.samsungperu.com/ PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA S.A. Rua Mário Dioniso, No2 - 1º Drt. 2795-140 LINDA-A-VELHA Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120 http://www.samsung.pt/ SOUTH AFRICA : Samsung Electronics,5 Libertas Road, Somerset Office Park, Bryanston Ext 16.
Fax. : (01952) 292 033 http://samsungservice.co.uk/ U.S.A. : Samsung Electronics America Service Division 400 Valley Road, Suite 201 Mount Arlington, NJ 07856 1-800-SAMSUNG (1-800-726-7864) http://samsungusa.com/monitor/ Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'.
1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. { For example, the number of TFT LCD sub pixels that is contained in this product are 2,359,296 / 3,932,160. 3. When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it.
FCC Information | IC Compliance Notice | MPR II Compliance European Notice (Europe only) | PCT Notice | VCCI | TCO'95-Ecological requirements for personal computers (TCO'95 applied model only) TCO'99-Ecological requirements for personal computers (TCO'99 applied model only) TCO'03-Ecological requirements for personal computers (TCO'03 applied model only) TCO'03 Recycling Information (TCO'03 applied model only) Medical Requirement Mercury Statement (LCD Monitor, LCD TV, DLP Projection TV, Projector for USA o
MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice(Europe Only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic and climate-influencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of energy, since it is often routinely left running continuously.
electronics components concerned with the display unit. CFCs (freons) CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer (malignant melanoma).
via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
Energy z Energy-saving mode after a certain time ?beneficial both for the user and the environment z Electrical safety Emissions z z Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 z Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead.
This equipment has been tested and found to comply with the limits for medical devices to the IEC 601-1-2:1994. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur.
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.