User Guide
Table Of Contents
- Important safety information
- Overview
- Using the cooktop burners
- Care and cleaning of the cooktop
- Troubleshooting
- Warranty
- Appendix
- Información importante de seguridad
- Descripción general
- Uso de los quemadores de la cubierta
- Cuidado y limpieza de la cubierta
- Superficie de la cubierta
- Superficies de porcelana esmaltada (en algunos modelos)
- Superficies de acero inoxidable (en algunos modelos)
- Perillas de control
- Rejillas y componentes de los quemadores
- Tapas y cabezales de los quemadores
- Bases de los quemadores
- Electrodos
- Rejillas y la rejilla para wok
- Comal de hierro fundido (para NA30K7750T*/NA36K7750T* solamente)
- Reemplazo del cabezal y la tapa de los quemadores
- Tapa de los quemadores
- Resolución de problemas
- Garantía
- Apéndice
- Informations importantes relatives à la sécurité
- Présentation
- Utilisation des brûleurs de la table de cuisson
- Entretien et nettoyage de la table de cuisson
- Surface de la table de cuisson
- Surfaces en émail vitrifié (sur certains modèles)
- Surfaces en acier inoxydable (sur certains modèles)
- Boutons de commande
- Grilles et composants des brûleurs
- Chapeaux et têtes des brûleurs
- Bases des brûleurs
- Électrodes
- Grilles et grille du wok
- Gril en fonte (uniquement pour NA30K7750T*/NA36K7750T*)
- Remplacement des chapeaux et têtes des brûleurs
- Chapeau du brûleur
- Dépannage
- Garantie
- Annexe
English 25
Troubleshooting
Problem Cause Action
Surface
burners do
not light.
The control knob is not set
properly.
Push in the control knob and
turn it to the Lite position.
The burner caps are not in
place.
The burner base is misaligned.
Clean the electrodes.
Put the burner cap on the
burner head.
Align the burner base.
A surface
burner
clicks during
operation.
The control knob has been left
in the Lite position.
After the burner lights, turn
the control knob to a desired
setting.
If the burner still clicks, contact
a service technician.
The burners
do not burn
evenly.
Surface burner components
and caps are not assembled
correctly and level.
pages 22, 23, and 24.
The surface burners are dirty. Clean the surface burner
components.
(pages 20, 21, and 22.)
Very large
or yellow
surface
burner
ames.
The wrong burner orice is
installed.
Check the burner orice size.
Contact your installer if you
have the wrong orice (LP
gas instead of natural gas or
natural gas instead of LP gas).
Troubleshooting
If you encounter a problem with the cooktop, check the tables starting below, and
then try the suggested actions.
Checkpoints
Gas safety
Problem Possible cause Action
You smell gas. The surface burner knob
is not in the OFF position
and the burner is not lit.
Turn the burner knob to OFF.
There is a gas leak. Clear the room, building, or area
of all occupants.
Immediately call your gas supplier
from a neighbor’s phone. Do
not call from your phone. It is
electrical and could cause a spark
that could ignite the gas. Follow
the gas supplier’s instructions.
If you cannot reach your gas
supplier, call the re department.
Surface burner
Problem Cause Action
All burners
do not light.
The power cord is not plugged
into the electrical outlet.
Make sure the electrical plug
is plugged into a live, properly
grounded outlet.
A fuse in your home may be
blown or the circuit breaker
may have tripped.
Replace the fuse or reset the
circuit breaker.
The gas supply is not properly
connected or turned on.
See the Installation Instructions
that came with your cooktop.
NA30N6555TG_DG68-01089A-01_EN+MES+CFR.indb 25 5/28/2018 12:47:26 PM