M40 1.0 Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice.
Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed. Always follow these instructions to help guard against personal injury and damage to your system.
Care During Use • Do not walk on the power cord or allow anything to rest on it. • Do not spill anything on the system. The best way to avoid spills is to not eat or drink near your system. • Some products have a replaceable CMOS battery on the system board. There is • • a danger of explosion if the CMOS battery is replaced incorrectly. Replace the battery with the same or equivalent type recommended by the manufacturer. Dispose of batteries according to the manufacturer’s instructions.
Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact an authorized service location.
Regulatory Compliance Statements Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device. Additional limitations, cautions, and concerns for specific countries are listed in the specific country sections (or country group sections).
In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated. When in environments where you are uncertain of the sanction to use wireless devices, ask the applicable authority for authorization prior to use or turning on the wireless device.
United States of America Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Written by: Daryl L. Osden This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on. The power output of the wireless device (or devices), which may be embedded in your notebook, is well below the RF exposure limits as set by the FCC.
If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par Industrie Canada.
Telecommunications per DOC notice (for products fitted with an IC-compliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users’ satisfaction.
European Union The following information is only applicable to systems labeled with the CE mark .
European States qualified under wireless approvals: EU Austria, Belgium, Denmark, Finland, France (with frequency restrictions), Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden and the United Kingdom. Accept EU Iceland, Liechtenstein, Norway and Switzerland European States with restrictions on use: EU In France, the frequency range is restricted to 2446.5-2483.5 MHz for devices above 10 mW transmitting power such as wireless LAN.
Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows® XP operating system. Whether you are new to using a portable computer or are an experienced user, this user’s manual can help you get the most from your computer. Manual Documentation Conventions Information Icons Four icons and their associated messages appear in this manual. The information icons are placed before the step/information they apply to: Warning: Indicates the possibility of personal injury.
CD-ROM Device Naming Convention In many installation programs you will have to get a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD. For instance, if you have one HDD with two partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.
Getting Started Introducing Your Computer The photographs used in this user manual may be somewhat different in shape and colour to those of your computer depending on the model of your computer.
Right View Headphone Jack Microphone Jack CD Drive (option, p24) USB Ports (2.0) Left View 1394 Port (4pin) Fan Vent Modem Port (p36) 4 Users Manual LAN Port (p37) Monitor Port USB Port (2.
Back View TV-Out Port (S-VHS) DC Jack Battery (p74) Security Lock Port (p79) S/PDIF Port (p28) Bottom View Battery Latches Fan Vent Memory Compartment (p77) HDD Compartment Mini-PCI Compartment* Removing or disassembling the hard disk drive will void your warranty. To replace the hard disk drive, please contact your nearest Samsung Service Centre. Wireless LAN module(optional) is installed in the mini PCI compartment.
Turning the Computer On and Off To turn on the computer 1. Insert the battery and connect the AC adapter according to the Installation Guide. 2. Slide the LCD latch to the right and open the LCD panel. 3. Press the power button. To turn off the computer 1. Click the start button ( 2. Click Turn Off Computer. 3. Click Turn Off. 6 Users Manual ) on the taskbar.
If the computer does not turn off properly due to a system error, press ++. When [Windows Task Manager] dialog box appears, click Shut Down > Turn Off to turn off the computer. Your unsaved work may be lost/damaged. If ++ keys do not operate either, press the power button for more than 4 seconds to turn off the computer. Your unsaved work may be lost/damaged. When you turn on the computer next time, it will perform a disk checking process.
Using the Keyboard Your computer has an 88/89-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function & Special Purpose Keys Function Key Windows Key Embedded Numeric Keypad Application Key Cursor/Screen Control Keys Although the layout of the keys on your computer’s keyboard is different from that on a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you use it.
To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and the surface around the keys. Do not allow liquid to drip into the keyboard or you may damage the keyboard. Using the Numeric Keypad Your keyboard includes a numeric keypad, which is a group of keys that you can set to type numbers and mathematical symbols, such as the plus sign. A number or symbol on the left corner of each keypad key shows its numeric function.
Using Special Function Keys The function key activates special functions when it is pressed in combination with another keys. Table 2 shows the special key combinations. Key Combinations Key Name Key Function Gauge Displays the remaining battery charge (%).
Number Lock Enables the numeric keypad. (p9) Scroll Lock Scrolls the screen up and down while the cursor position does not change in some applications. < / > Brightness Up Makes the LCD screen brighter. < / > Brightness Down Makes the LCD screen dimmer. < / > Volume Down Decreases the audio volume. < / > Volume Up Increases the audio volume.
Using the Touchpad In Windows, you always see a small graphical image on the screen that indicates the location where you can take the next action. This image is called a pointer, and is usually displayed in arrow shape ( ) or ‘I’ shape ( ). Touchpad Touchpad Buttons The touchpad on your computer allows you to move the pointer on the LCD screen, just like a mouse that is used with a desktop computer.
You can perform various actions with your touchpad as described below. d Action Function Process Move Move the pointer Place your finger on the touchpad and slide your finger to a destination. Click Select an object, open a menu, or execute a button Place the pointer over an object, then press left touchpad button once. Or, place the pointer over an object, then tap the touchpad once with your finger.
Action Function Process Scroll Display upper/lower/left/right part of the content within a window Place your finger on the right edge of the touchpad and move vertically. (Applicable to certain programs only) Make sure to use your finger to move the pointer with the touchpad. Do not use any sharpened tool because it may damage your touchpad.
Hot Keys Icon Name Function Internet Button Launches Internet Explorer. E-Mail Button Launches Outlook Express. User 1 Button Launches a user defined program. WLAN Button Turns on and off the wireless LAN function for the models with wireless LAN function. Turns on and off the touchpad for models without a wireless LAN option. Using Wireless LAN Button Loading or unloading wireless LAN driver takes about 5 seconds.
Changing the Hot Key Setting You can change the program that will be launched when you press a hot key. As default, Windows Calculator is configured to launch when you press the User 1 button. You can set the program by completing the following procedure. 1. Double-click the Magic Keyboard icon ( ) on the taskbar. 2. Select USER 1 and then click Browse. 3. Select the desired program in [Open] dialog box, and click Open. (Example: Paint) 4. Click OK to save the changes.
Reading the Status Indicators LED Name Function Num Lock Turns on when the numeric keypad is activated. Caps Lock Turns on when the user has set the option for typing letters in upper case. Scroll Lock Turns on when it is set to scroll the screen up and down while the cursor position does not change in some applications. HDD Blinks when the hard disk drive is operating. Battery Turns green - when the battery is fully charged, or when the battery is not installed.
Adjusting LCD Brightness There are 8 levels of LCD brightness (1: Dimmest ~ 8: Brightest). Press +< / > or +< / > keys from the keyboard to adjust LCD brightness. When changed, the current LCD brightness is displayed on the top left corner of the LCD screen for a few seconds. Whenever you turn the system on or change the power source the brightness level changes according to the settings.
Adjusting the Volume To adjust using keyboard Press +< / > or +< / > from the keyboard. To adjust using volume control program Click the Volume icon( level. ) on the taskbar, and move the Volume slider to a desired For advanced volume control options, double-click the Volume icon ( the volume level in the volume control program.
Introducing Windows Understanding the Desktop The desktop is the working area on the computer. It consists of the large workspace and a taskbar at the bottom. Shortcut Icons Start Menu Recycle Bin Language Bar Start Button Taskbar System Tray with Clock Start Button Opens the Start menu. Taskbar Displays programs that are currently running. Frequently used icons can be placed here. Recycle Bin Deleted files or folders are sent here. Language Bar Switches text input language.
Understanding the Start Menu The Start menu includes everything that is required to start Windows. From the Start menu it is possible to run a program, open a file, assign system users with Control Panel, receive support by clicking Help and Support, and search desired items from the computer or Internet by clicking Search.
Understanding a Window A window is the basic component in working with the computer. The My Computer window, which is a window for the computer's hard drive, will be used as an example here to show the basic composition of a window. Click Start > My Computer. Folder Icon Title Bar Menu Bar Close Button Maximize Button Minimize Button Quick Task Window Folders Files Double-click Shared Documents or Local Disk. You can see files and folders.
Help and Support Center Help and Support Center provides references and troubleshooting information regarding computer use. Click Start > Help and Support. Windows XP Tour You can tour elementary functions provided by Windows XP. Click Start > Tour Windows XP. Or click Start > All Programs > Accessories > Tour Windows XP. Click on the topics to find out about important functions of Windows XP.
Using the Computer Using the CD Drive You have one of following drives installed in your computer. CD-ROM drive Reads a CD. CD-RW/DVD-ROM Combo drive Reads a CD/DVD and writes a CD. DVD Super Multi drive Reads CD/DVDs and writes data to CD/DVDs. Supported DVD types include DVD ± R, DVD ± RW and DVD-RAM. To insert a CD 1. Press the eject button on right side of the CD drive. 2. When the tray slides out, place a CD onto the tray with the label facing up, and push the CD down until it clicks.
If you remove the CD when the CD access LED is on, the disk and the data in it may be damaged. Emergency Eject Hole To eject a CD when the CD drive is not working or the computer is turned off, unfold a paperclip, and insert the unfolded end of the clip into the emergency eject hole (located next to the eject button) and press until the CD tray opens. To clean a CD or DVD title Clean the disc with a soft clean cloth by wiping from the center outwards.
To play a video CD If a video CD does not run automatically, follow these steps. 1. Insert a video CD into the CD drive. 2. When the CD drive window appears, double-click the MPEGAV folder. 3. Double-click the .dat file. 4. When the [Caution] dialog box appears, click Open With. 5. Select “Select the program from a list” and click OK. 6. Select the Windows Media Player, and click OK. The video starts playing. The above procedure only applies to the video CDs that have a .dat file as the execution file.
4. In My Computer window, select files and folders to copy, then drag and drop them onto the CD drive window. My Computer window CD drive window 4. Drag and drop folders or files to copy. 5. Click Write these files to CD. 5. Click Write these files to CD in the CD drive window. 6. When the CD Writing Wizard appears, enter the CD label, and click Next. The data begins copying. 7. When copying is completed, a ‘completed’ message appears and the CD drive window opens automatically.
Enjoying Home Theater (S/PDIF Port) Your computer supports 5.1 channel output, which is a basic function for home theater systems, and DVD drive. It provides 3D surround sound and vivid screen. What is a home theater system? Home theater system usually consists of a TV, DVD, 5.1 channel speaker, and a digital amp which provides a high-resolution screen (MPEG2) and 3D surround sound (Dolby 5.1 or DTS).
Step 1. Connect 5.1 channel speaker system to your computer 1. Connect an amplifier to the S/PDIF port on your computer. 2. Connect speakers to the amplifier. (Refer to the speaker system’s manual.) 3. To watch through a TV, connect the TV, and change the display device to the TV in the Display Properties. (Refer to ”Using External Display Devices” (p 67).) TV Digital Amplifier Sub Woofer Front Right Speaker Front Left Speaker Computer Center Speaker Surround Left Speaker Surround Right Speaker Step 2.
Step 3. Enable S/PDIF in the DVD program To use 5.1 channel speakers, you need to install the Power DVD program from the System Software CD provided with your computer, then change the settings as per the following. 1. Run Power DVD program and click the Settings icon ( ). 2. On the Audio tab, set the Speaker Environment setting to “Use SPDIF” and click OK. Now, you can enjoy home theater using DVD titles. To control volume for your 5.1 channel speaker, use the control on the digital amp.
Using the PCMCIA Card Slot Various different functions can be added by inserting PCMCIA cards into the system. This system supports 16/32 bit, type I or II PCMCIA card types. The PCMCIA card slot does not support a ZV card or a PCMCIA III card. To insert a PCMCIA card Before using the PCMCIA slot, remove the slot protector. Push the eject button of the PCMCIA card slot once to pop it out. Push the button again to eject the slot protector. 1.
To remove a PCMCIA card 1. Double-click Safely Removes Hardware icon ( ) on the taskbar. 2. On the [Safely Remove Hardware] dialog box, select the appropriate PCMCIA card and click Stop. 3. When [Stop a Hardware Device] dialog box appears, click OK. 4. Click Close to close the [Safely Remove Hardware] dialog box. 5. Push eject button of the PCMCIA card slot once, and the button pops out. 6. Push the button again to eject the PCMCIA card.
Using the Memory Stick Slot Memory Stick is popular as a removable storage device similar to a floppy diskette. It is widely used for many digital products like digital cameras, PDAs, etc. Users can easily install a memory stick to save and remove data on it. Restrictions for using a Memory Stick/Memory Stick Pro Memory Sticks and Memory Sticks Pro (256MB ~ 1GB, about 1 MB/s data rate) can only be used as data saving devices. The copyright protection function is not supported for these memory sticks. 1.
To format Memory Stick Pro You cannot format Memory Stick Pro using Windows XP or Memory Stick Formatter. Format it in other digital devices. To protect data in a memory stick To prevent overwriting or deleting the data in the memory stick, move the slide lock to the "Lock" position. To remove a memory stick in Windows 2000 Only remove a memory stick after at least 20 seconds after finishing a task, such as formatting, copying or deleting.
Using Samsung Theme Samsung Theme is a program that enables a user to easily switch a theme (desktop, logon screen and sound effect). Double-click the Samsung Theme ( ) icon on the desktop. (Or select Start > All Programs > Samsung Software > Samsung Theme > Samsung Theme.) Close button Help button Move the mouse pointer over Samsung Theme item, then the Samsung Theme will be displayed below. • Samsung Theme: Switches to Samsung Theme (desktop, logon screen and sound effects on booting).
Connecting to the Internet Connecting with a Modem Before Start: • Prepare a telephone line that is not digital. • Contact an internet service provider (ISP) for instructions on how to connect to and disconnect from the Internet. 1. Connect a telephone line to the computer’s modem port. 2. Connect to the Internet according to the instructions provided by your ISP. If the Internet connection is not disconnected properly, additional telephone charges may be imposed.
Connecting Through a Wired LAN 1. Connect a LAN cable to the computer’s LAN port. 2. Click Start > Control Panel. 3. Click Network and Internet Connections in the [Control Panel] window. 4. Click Network Connections in the [Network and Internet Connections] window. 5. Right-click the Local Area Connection icon and click Properties.
6. On the General tab, select “Internet Protocol(TCP/IP)” and click Properties. 7. To use DHCP: On the General tab, select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click OK. To use a static IP: On the General tab, select “Use the following IP address” and fill in the IP address, Subnet mask, Default gateway, Preferred DNS server, and Alternative DNS server fields. Click OK.
Using Samsung Network Manager Use Samsung Network Manager to configure network setting. Using the program, you can do the following. • You can save network settings (including IP address) according to network places such as office and home. When you change places, simply select a network place and the network settings will be automatically changed accordingly. • You can easily find out your current IP. To configure network setting 1. Connect LAN cable to the computer's LAN port. 2.
5. New place icon is displayed and full dialog box appears. Check your IP and click Close. Network setting is saved. To configure network setting of some place other than current place, click the place icon and configure each network device. If you are using DHCP, select 'DHCP' check box and click Save. If you are using a static IP, clear 'DHCP' check box, enter appropriate network setting and click Save. Ask ISP or network administrator for IP address.
2. Click Change, select a place icon then click Change. Example) changing to Office 3. On "Do you want to change the location setting?" dialog box, click Ok. 4. When the network place is changed, corresponding place icon is displayed in color and full dialog box appears. In the right area of full dialog box, network setting is displayed. 5. Click Close to close the dialog box.
Connecting Through a Wireless LAN (Option) A wireless network (Wireless LAN) environment is a network environment that enables communication between multiple computers at home or a small-size office through wireless LAN devices. Using the wireless network connections between the systems, you can use normal network functions such as sharing of files, folders and printers.
What is an Access Point (AP)? An AP is a network device that bridges wired and wireless LANs, and corresponds to a wireless hub in a wired network. You can connect multiple wireless LAN installed computers to an AP. 2) Computer-to-computer (ad hoc) This is also called a peer-to-peer network. In computer-to-computer wireless networks, you can wirelessly connect 2 or more computers that have wireless LAN modules.
2. Select your desired AP (e.g. Test) to connect, and enter the encryption key for the AP in the Network key field, and click Connect. If the network key is not configured for the desired AP, select 'Allow me to connect to the selected wireless network, even though it is not secure’. Now you are connected to the AP, and you can access the network. Checking the connection status Move the mouse pointer over the Wireless Network Connection ( the taskbar, and the connection status is displayed.
Connecting to computer-to-computer networks (peer-to-peer or ad hoc) In computer-to-computer wireless networks, you can wirelessly connect 2 or more computers that have wireless LAN modules. Using this method, a computer that is not connected to the Internet can share the Internet by accessing another computer connected to the Internet. (Refer to ”Sharing an Internet connection through a wireless network” (p 59).) You can connect by completing the following steps: • Step 1.
2. Click Advanced. 3. On the Wireless Network tab, click Advanced. 4. Clear 'Automatically connect to non-default network' check box, if it is selected. Select 'Computer-to-computer (ad hoc) networks only', and click Close. 5. In the Wireless Networks tab, click Add.
6. Enter the network name (e.g. samsung), and unselect 'The key is provided for me automatically'. Enter the encryption key in the Network key field, and click OK. To prevent a network connection from an unauthorized user, it would be better to configure a network key (encryption key). A network key consists of 5 or 13 alphanumeric characters (e.g. magic), or of 10 or 26 hexadecimal numbers (a hexadecimal number is represented by numbers '0' to '9' or letters 'a' to 'f').
7. Check that the configured network name (e.g. samsung) is in the ’Preferred networks’ item, and click OK. Now your wireless network setup has been completed. Step 2. Connecting to the configured computer 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks. ) icon on the taskbar, and 2. Select the wireless network name (e.g.
If the network key is not configured in ”Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 45, select 'Allow me to connect to the selected wireless network, even though it is not secure'. The two computers are connected and are able to communicate with each other. When the computers are connected, the 'Wireless Network Connection' message is displayed for a short time over the Wireless Network Connection icon of the two computers.
Wireless Network Setup Using the Wireless LAN Setup Program When the operating system of your computer is not Windows XP, you should setup the wireless network settings using an additional wireless LAN setup program (PROSet). To use wireless network connection, complete the following procedures. • Step1. Install the wireless LAN configuration program (PROSet). • Step2. Configure wireless network settings through the wireless LAN configuration program. Step 1.
To connect to an Access Point: To connect to an access point or existing computer-to-computer (Ad Hoc) network, refer to the following procedures. (To create a new computer-to-computer network, refer to the following "To create computer-to-computer (Ad Hoc) network" section.) 1. Click Scan in the Networks tab. 2. Select the name of desired access point or computer-to-computer network to connect from the searched available networks list, and click Connect.
- Data encryption (WEP): The IEEE 802.11 WEP (Wired Equivalent Privacy) standard defines two levels of encryption, a 64-bit key (this is sometimes represented by 40bits) and a 128-bit key. - Key index: Select the current encryption key index used by the access point out of 1 to 4. - To use pass phrase: Click Use pass phrase to activate, and enter 5 (for 64bit) or 13 (for 128-bit) alphanumeric characters (represented by 0-9, a-z, or AZ).
3. Configure password setting to be used for computer-to-computer network connection in the Security Settings window. To connect to an access point, enter the network authentication, data encryption (WEP), key index, and password configured in the access point. It is recommended to configure data encryption for security purposes when creating a computer-to-computer network connection profile. For more information on security settings refer to the security settings in Connecting to AP or Help.
Using Network Services While the computer is connected to the network, you can use network services to share files, folders, and printers. Using computer-to-computer wireless networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet. Network services are provided for the computers that are connected to the network through wired or wireless network connections.
Step 1. Configuring Sharing 1. Right-click the target file or folder to share in My Computer, and select Sharing and Security. 2. Click 'IF you understand the security risks but want to share files without running the wizard, click here'. It has the same security effect as that of the 'Network Setup Wizard'. This screen does not appear if Internet Sharing Network Wizard has been installed in the computer-to-computer wireless network environment. 3. Select 'Just enable file sharing', and click OK. 4.
Step 2. Using Shared Files or Folders This section describes how to access shared files or folders if your computer is a member of the same workgroup. 1. Click Start > My Computer. Under Other Places, click My Network Places in your computer. 2. Click 'View workgroup computers', and click the desired computer to access the shared file. If your computer is a member of another workgroup: 1. Click Other Places > Microsoft Windows Network. 2. Click the desired workgroup. 3.
Step 1. Configuring Printer Sharing 1. From the computer connected to the printer, click Start > Printers and Faxes. 2. Right-click the printer you want to share, and click Sharing. 3. Select 'Share this printer', enter a share name for the shared printer, and click OK. 4. In the Printers and Faxes window, you will find the printer icon has been changed to another icon on a hand. Step 2. Adding and Using a Shared Printer. 1.
5. Select 'Browse for a printer', and click Next. 6. Select the workgroup or computer, select the desired printer, and click Next. If you cannot find the desired printer, try again after a while. 7. Read the warning about a shared printer, and click Yes to install the shared printer. 8. Select Yes for 'Do you want to use this printer as a default printer?', and click Next. 9. Click Finish. 10.
Sharing an Internet connection through a wireless network By connecting your computer to another computer, which is connected to the Internet over a wired connection, through a wireless network (Peer-to- Peer), you can access the Internet from your computer. To share an Internet connection, the computers should be connected to a computer-to-computer (peer-to-peer) wireless network. For details, see “Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 45.
If the computer is connected to the Internet through a wired LAN, select 'Local Area Connection'. 3. On the Advanced tab, select 'Allow other network users to connect through this computer's Internet connection', and click OK. Step 2. Checking the Shared Internet Connection. When the Internet connection sharing configuration has been completed, the network icon in the Network Connections window is displayed as follows: Click Start > Control Panel > Network and Internet Connections > Network Connections.
Customizing Your Computer Using System Setup The System Setup (BIOS) program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in battery-maintained CMOS memory that saves the information even when the computer’s power is turned off. When your computer is turned back on, it is configured with the values found in this memory. Run System Setup if you get a message prompting you to run the program.
Starting System Setup To start System Setup, turn on your computer and then press and hold until the System Setup screen appears. Table 2. System Setup Menus Menu Function Main Changes the basic system. Advanced Configures advanced features on your computer. Security Enables security features, including passwords. Boot Specifies the order of boot devices and configures boot features. Exit Specifies how to exit System Setup.
Changing Booting Priority You can select the booting priority among the devices such as the hard drive, CD-ROM drive, etc. The following example describes how to configure the hard drive as the first booting device when the CD-ROM drive is configured as the first booting device by default. 1. Select the Boot menu in System Setup. 2. Press on Boot Device Priority item. 3. Use < > key to move to the Hard Drive item, and press until it is at the very top. 4.
Configuring the Password Setting the Supervisor Password By configuring a supervisor password, you can restrict system access to authorized users only. Do not lose or forget your password. If you have forgotten your password, contact the Samsung service center. 1. Select the Security menu in the System Setup. To enter System Setup, see “Starting System Setup” on page 62. 2. On the Set Supervisor Password item, press . 3.
Activating the Booting Password Before activating the booting password, the supervisor password must have been configured. Set the Password on boot option to [Enabled]. From now on, system booting will not proceed without the password. Activating the Hard Disk Drive Password Activating the hard disk drive password prevents the currently installed hard disk drive from being used in other systems.
Configuring Resolution and Colour Depth Screen resolution is the number of pixels displayed on the screen. High resolution makes the overall screen area large, although individual items appear small. Colour quality is determined by the number of bits used to represent a pixel on the screen. High colour quality displays more number of colours on your screen. 1. Select Start > Control Panel > Appearance and Themes > Change the screen resolution. 2.
Using External Display Devices Using external display devices such as monitors, projectors, TVs, etc allows you to view screen images alternatively or simultaneously on each device. Additionally, you can extend the screen onto two display devices to use a larger workspace. Using external display devices is especially useful when you are giving a presentation or watching a movie through your TV.
Using Dual View to View Extended Screen You can expand the screen into two display devices and work conveniently in separate workspaces. In Dual View mode, you can select the screen resolution and colour quality for each display device, as if there were two separate graphics cards. 1. Connect the external display device (e.g. a monitor or a projector) to the corresponding port of the system. To connect a TV, connect the TV to the TV output port of the system. 2.
secondary display device is indicated as '2'. Now you can view the screen through two monitors. 1 : Primary 2 : Secondary When using Dual View, only the LCD can be configured as the primary display device. If the screen of the secondary display device is displayed at 640x480 pixels, with 256 colours, change the settings to the desired screen resolution and colour quality in the [Display Properties] dialog box.
System Management Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance. Your computer runs fastest with the power cord attached, whereby power management is disabled.
3. Click the Power Schemes tab to display the basic power management options. By default, the power scheme is configured to SAMSUNG mode. SAMSUNG mode extends the battery life and optimizes the Intel Speedstep function. Since the CPU power consumption is automatically optimized to conserve power when the computer is operating on battery power, an application may be executed slower than when it is operating on AC power.
If You Reinstall Windows: You should re-establish hibernate in power options by opening Power Options Properties window and click on the Hibernate tab then click “Enable Hibernation”. Hibernate Tab Frequent Interruptions: If you experience frequent interruptions, you might also consider putting your computer into automatic hibernation after a specified number of minutes using the power management options.
Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Control Panel > Performance and Maintenance. 2. Click icon to display the Power Options Properties window. 3. Click the Advanced tab to display the advanced power management options. Advanced Tab Power & Sleep Button Programming Windows 4.
Using the Battery Please refer to the following instructions when running the computer on battery power without connecting the AC power. Please read the instructions on the battery before use. Please refer to the system operation environment (p110) of this manual and operate and store the battery at room temperature. Ejecting and Attaching Battery 1. Shutdown the system and close LCD. 2. Put the computer upside down on a flat surface. 3. Pull the two battery latches outward, then remove the battery. 4.
Using the bridge battery Your computer has a bridge battery, which supplies power for a short time even when there is no battery installed. Thus you can exchange a battery in standby mode, without turning the computer completely off. When you are exchanging the battery in standby mode, exchange in 3 minutes. Monitoring the Battery Charge To monitor using a shortcut key Press + keys to view the remaining battery charge.
Battery Calibration Calibrating your battery once a month is one of the recommended methods of increasing your computer’s battery life. To calibrate the battery complete the following steps: Calibration Notes: You should start the battery calibration process with a fully charged battery, battery status LED is green. However, the power meter may not show 100%. Before you commence the battery calibration process you should fully charge, then fully discharge and finally fully recharge the battery again. 1.
Upgrading Memory This computer has one or more 128 MB or 256 MB memory module(s). Two memory module sockets are provided so that you can replace memory or install an additional memory module. Removing the memory module Before removing/replacing the memory module, turn the system off completely. Do not replace the memory module when the system is in Standby/Hibernate mode. 1. Using a screwdriver, open the memory module compartment cover on the bottom of the computer. screw 2.
Adding a memory module 1. Align the new memory module connectors accordingly and slide it into the slot at a 30° angle. Ensure the notch on the memory module corresponds with the notch on the socket. 2. Push the memory module in until the module clicks into place. If the memory module is not fixed completely, gently push the memory down while pressing the memory module tabs outward. 3. Close and fix the memory module compartment cover using a screwdriver.
Using the Security Lock Port The security lock is a device used to physically 'fix' the system when using it in a public place. The locking device needs to be purchased separately. The shape and methods of use may differ depending on the manufacturer. Please refer to the manual provided with the security lock for proper use. Connect a security lock cable to a fixed object, and to the security lock port on the back of the computer.
Tips for Using Your Computer The following information helps you avoid potential problems as you use your computer: Do not try to disassemble your computer. Opening the system chassis or removing the hard disk drive voids your warranty. Only an authorised Samsung service center can replace or add any parts inside the chassis. • Follow all the instructions and cautions in your computer user documentation. • The LCD has a polarized surface and can be damaged easily.
Travelling with Your Computer Air Travel If you are travelling by air, follow these tips: • Take the computer with you as carry-on luggage. Do not check the computer with your baggage. • Allow the computer and disks to go through the X-ray security devices. Do not hand-carry disks through the walk-through metal detectors, which can cause loss of data. • Make sure that the battery is charged or the power cord is easily accessible. You may be required to turn on the computer for airport security personnel.
Storing the Computer for Long Periods If you will not be using the computer for a long period of time (a month or more), you should discharge the battery completely then remove the battery from the computer. This extends the life of the battery.
Troubleshooting Complete the following in the order presented until your system is functioning properly. If all of the steps below fail then contact your local reseller for assistance. Questions and Answers Please see “Questions and Answers” on page 84 for assistance in correcting any computer operational problems. Check the Connections Verify all of the power and peripheral cables are securely plugged into their sockets and that your system and power supply is on.
Questions and Answers This section provides information on possible problems, solutions and other references for system use. Windows Related Q1 The system does not shutdown properly. A When the system does not shutdown normally, press and hold the Power button until the system manually shuts off. If the Power-Saving Mode is configured into the Power button, press and hold for more than 4 seconds to shut the system off.
Display Related Q1 The LCD screen is blank. A Adjust the LCD screen brightness. Use the +< >, +< > keys. Q2 The screen saver disturbs screen viewing during Media Player or video file operation. A Under the Media Player Options, in Player > Enable Screen Saver During Use, uncheck the box and restart the player.
device, removing the AC adapter, restarting the system, or changing the PowerMizer level) A This may happen while the video driver is examining the connected device. Q7 When I connect a projector, and change the setting to display screen image on both the LCD and the projector by pressing + keys, screen is not displayed properly. A Press + keys once again.
Q12 When I connected a TV, some programs, such as Mem, do not run properly in Full-DOS Screen. A When you are using a TV as display device, some programs, such as Mem, may not run properly in Full-DOS Screen. Run the program in DOS window mode. Q13 When I pressed + keys to change to full screen mode while playing a music file in Windows Media Player, the sound may be stopped for a short period.
Modem Related Q1 I cannot hear the modem sound. A1 Check that the telephone line is properly connected to the modem. A2 Check that the modem driver is installed properly. 1. Click Start > Control Panel > Performance and Maintenance > System. 2. Select Hardware tab > Device Manager > Modems in the System Properties window, and check if there is a yellow exclamation mark on the installed modem icon.
- Using an AT command As an initialization command, use the command, ATX3. Otherwise, enter the ATX3 command manually before making a call. It can correct this problem by skipping the dial tone check step. - Configuring the Modem through the Control Panel 1. Click Start > Control Panel > Network and Internet Connections. 2. Under See Also, click Phone and Modem Options. 3. In the Modems tab, select the installed modem, and click Properties. 4.
4. In the Modems tab, select the installed modem, and click Properties. 5. In the Power Management tab of the Modem Properties window, select the "Allow this device to bring the computer out of standby." check box, and click OK. The above setting enables the modem to turn on the system and receive a fax when in Standby mode.
Wired LAN Related Q1 function A is a function that activates the system in rest mode when a signal (such as ping or magic packet commands) arrives from network (wired LAN). To use function: 1. Click Start > My Computer > My Network Places > View network connections. 2. Click the right button of the touchpad over Local Area Connection, and select Properties. 3. Click Configure, and select Power Management tab.
Wireless LAN Related Refer to ”Connecting Through a Wireless LAN (Option)” (p 42) for the basic uses of a wireless LAN. Q1 The Wireless LAN device is operating properly, but I cannot connect to the Internet or to another computer. This is due to an incorrect configuration, or a configuration error. Check the following check lists: A1 If you are using a computer-to-computer (Ad Hoc) network connection, check that the name of the configured network (SSID) is correct.
Q3 I cannot share an Internet connection. A1 It may require some time to synchronize the computers to share an Internet connection after the Internet connection sharing configuration is completed. If you cannot share Internet connection even after a longer period, restart the computer. A2 Check if the connection between the network adapters is configured to bridge.
- Verify whether the AP's firmware is the most recent version. (Contact the AP manufacturer or the place where you purchased the AP for details of the AP firmware.) A5 Verify whether the AP has been properly connected to the network. Verify whether the network is operating normally by connecting the wired network cable, which has been connected to the AP, to your computer. A6 Check the network key settings (encryption key).
disable the [View Available Wireless Networks] window supported by WZC service. Exit the wireless LAN related program then check whether the window is enabled. A3 Initialize the device driver. Click Start > Control Panel > Performance and Maintenance > System > Hardware tab > Device Manager > Network adapters, and select the wireless LAN adapter. Right-click the network adaptor and select 'Disable'.
through a computer-to-computer (Ad Hoc) network should be configured so that their IP addresses are within the same subnet range. - If the IP address is configured to DHCP (Obtain an IP address automatically) in TCP/IP properties, IP address is configured within the same subnet range automatically. - If the IP address is configured to static IP in TCP/IP properties, select Use the following IP address in the TCP/IP properties of the wireless adapter, configure IP address:10.0.0.1~10.0.0.
Q12 An established wireless LAN connection is disconnected after 2~3 minutes, and the connection is not recovered. A1 This may be caused by channel interference. Change the channel of the AP, and reconnect. A2 This may be caused by selecting the ’Use IEEE 802.1x network authentication’ option when IEEE 802.1x authentication is not available. Check the properties of the AP in the wireless network settings. If the ’Use IEEE 802.
supports the function. This version of the driver does not support the WPA function. Click Start > Control Panel > Add or Remove Programs > Add or Remove Programs and remove the Q815485 patch if it is installed. Q13 After PROSet is installed, The “AEGIS Protocol (IEEE 802.1x) v2.2.1.0” appears in the [Local Area Connection Properties] window.
Games and Programs Related Q1 3D game is not executed, or some functions are not working. A Change the graphic setting of the game to '2D' or 'Software Renderer', then execute the program again. Q2 I launched a game right after installing it, and the game is not executed. A This problem may occur when the game is not compatible with Windows XP. Launch the game again, and it will be executed properly. Q3 A game runs only in small screen format.
Q6 While running a game, + keys may not work or screen may not be displayed properly when the keys are pressed. A While running Direct3D game, display device configuration keys do not work to maintain the system stability. Since display device control varies depending on the type of display devices in some games, the screen may not displayed properly. Use + keys before starting a game.
Q11 The screen may not be displayed properly in some games. A In some games including Harry Potter and Sorcerer's Stone and Harry Potter and the Chamber of Secrets, the screen may not displayed properly when you set the screen resolution to 1024x768 and color quality to 32 bits. Play these games in screen resolution - 1024x768 and color quality - 16 bits. Q12 The screen is severely interrupted in some games. A In 3D games, the texture data needed in 3D screen presentation are stored in the system memory.
Restoring the System This description is only for models running Window XP. The System Restore function allows you to restore your computer to an earlier copy (called restore point), and restores the settings if a problem occurs.The System Restore function is provided by Windows XP to enable the resolution of various problems without reinstalling Windows XP completely. You can use System Restore in the following cases. • • • • The system files are deleted or damaged by mistake.
2. Select "Create a restore point", and click Next. 3. In the Restore point description box, type a name to identify the restore point, and than click Create. A restore point has been created. Returning your computer to an earlier restore point The procedures to return your computer to an earlier restore point when a problem has occurred are described below. 1. Click Start > All Programs > Accessories > System Tools > System Restore. 2. Select "Restore my computer to an earlier time", and then click Next.
3. Select the desired restore date from the calendar restoration and select the desired restore point from the list, and then click Next. The date of the restore point is displayed in bold font. 4. Confirm the selected restore point and click Next. System Restore shuts down Windows, and starts the restoration processes. 5. After the restoration is complete, Windows restarts. In the [System Restore completed] dialog, click OK.Your computer has been restored to the selected restore point.
Reinstalling Software If you have reinstalled the Windows operating system, or the system and program do not operate properly, you can re-install the driver and program using the system software CD. The drivers and programs included in the system software CD are listed in the D:\ReadMe.htm file. (Provided that the name of CD-ROM drive is "D".) This computer is optimized for Microsoft Windows XP, therefore driver other than the ones included in the System Software CD are not provided.
Installing programs 1. In the initial screen, click Application Installation. 2. Click Standard installation in the program installation screen (standard installation is recommended). • Standard installation: Installs and recovers programs to the state of shipment. • User installation: You can select the program installation location, and other options for the program installation.
Reinstalling Windows XP If the Windows XP does not operate properly due to an error in the system, or if you have replaced the hard disk drive, you can reinstall Windows XP using the system recovery CD. With the system recovery CD, you can reinstall Windows XP only. To return the system to the state of shipment, reinstall the device drivers and programs with the system software CD after reinstalling Windows XP with the system recovery CD.
3. The description for the standard installation appears. Click Yes. The installation starts, and the system will be restarted after a while. 4. After the system has restarted, the message ’Press any key to boot from CD’ appears. Do not press any key at this time. After a while the partition configuration screen appears. To not change the partition, press . What is partition configuration? Partition configuration is a function that devides the hard disk drive into one or several partitions.
If You Cannot Run Windows If you cannot run Windows, you have to boot the system with the system recovery CD, and reinstall Windows. If you boot the system from the system recovery CD, you can install Windows only with the user installation option. You cannot install with the standard installation option. 1. Insert the system recovery CD into the CD-ROM drive and start the computer. 2. If the following message appears on the screen, press any key from the keyboard. Press any key to boot from CD.....
Specifications System Specification The following is the basic hardware specification for the purchased product. Variations may exist depending on the model type. Item Specification CPU Intel Pentium M 1.7 ~ 2.0GHz Cache memory 1MB(Banias)/2MB(Dothan) Main memory 128/256/512/1024 MB DDR SDRAM, 2 DDR socket Main Chipset Odem+ / ICH4M Remarks Max 2GB Hard disk drive (HDD) 2.5’’, UltraDMA 100, S.M.A.R.T 9.
Wireless LAN Specification (Optional) Intel(R) PRO/Wireless LAN 2100 3B Mini PCI Adapter Product Specification Item Physical Specifications Power Specification Network Specifications Detailed Specifications Dimensions (Width X Height) 59.75 X 44.45 mm operation temperature and humidity Same as system operation Power Saving Mode 135 mW Receiving Mode 1.0 W Transmission Mode 1.6 W Power 3.3V Compatibility IEEE802.
Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country. In France however, use only 4 channels (channel 10, 11, 12, 13) when using wireless networks. • Standard: IEEE 802.
Radio Specifications RF Band 2.4GHz (ISM band) Support Channels 1~13 channel (See "Regulatory Notice for Channel Use in France".) Device Transceiver Standard Output Power 5 mW Transmission Method 11b mode: DSSS 11g mode: OFDM Transmission Rate (Mbps) * 11b mode: 11, 5.5, 2, and 1 11g mode** : 54, 48, 36, 24, 18, 12, 9, and 6 Antenna Type Internal Antenna 2 EA (Main/Aux) * The transmission rate may differ from the actual transmission rate.
Abbreviations A . . . . . . . . . Amperes AC . . . . . . . . Alternating current ACPI . . . . . . Advanced Configuration and Power management Interface APM . . . . . . Advanced Power Management ATA. . . . . . . AT attachment (refers to the hard-drive interface in an ATcompatible computer) ATAPI. . . . . AT attachment packet interface BBS . . . . . . . Bulletin board system BIOS . . . . . . Basic input/output system C . . . . . . . . . Centigrade CD . . . . . . . . Compact disc CD-ROM . .
ISA . . . . . . . Industry Standard Architecture KB . . . . . . . . Kilobytes kg . . . . . . . . . Kilograms LAN. . . . . . . Local-area network lb.. . . . . . . . . Pounds LBA . . . . . . . Logical block addressing LCD. . . . . . . Liquid-crystal display m . . . . . . . . . Meters mA . . . . . . . . Milliampere mAhr . . . . . . Milliampere hour MB. . . . . . . . Megabyte mm . . . . . . . millimeter MPEG . . . . . Motion Picture Experts Group MPU . . . . . . Microprocessor unit ms . . . . . . . .
Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts). The 32-bit cards can transmit more data at a time than the 16-bit cards, thus increasing their speed. CMOS memory CMOS (complementary metal oxide semiconductor) memory is powered by the CMOS battery.
Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer. Because hard drives in notebook computers are smaller than those in desktop computers, their maximum storage capacity may be less than that of desktop hard drives.
PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed. Pixel A pixel is an individual dot in a graphic displayed on your computer. The pixels are so close together that they look as though they are connected.
Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer. TFT (thin film transistor) LCD A TFT LCD uses a separate transistor circuit to control each pixel. This technology provides the best resolution for an LCD screen. A TFT LCD is also sometimes called an active matrix LCD.
Using Windows 2000 Samsung notebook provides Windows XP or 2000 as operating system depending on the product model. Because the use of Windows XP is similar to Windows 2000, the same User Guide (Online Manual) is used regardless of operating system installed on your notebook. However, since there are some differences in menus, screens, and operations, you need to refer to this Guide if your notebook's operating system is Windows 2000.
Introducing Windows Descriptions presented in ”Introducing Windows” (p 20) are applicable only to Windows XP. For Windows 2000, location of menus, shape of icons and some uses may differ from those of Windows XP. To Playback Audio or Video CD Just insert your audio or video CD into your CD drive. The associated application program will start automatically and playback the audio or video files.