Notice and Safety With Wireless - English V1.1.fm Page i Friday, May 3, 2002 3:21 PM Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice.
Notice and Safety With Wireless - English V1.1.fm Page ii Friday, May 3, 2002 3:21 PM Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed. Always follow these instructions to help guard against personal injury and damage to your system.
Notice and Safety With Wireless - English V1.1.fm Page iii Friday, May 3, 2002 3:21 PM Care During Use • Do not walk on the power cord or allow anything to rest on it. • Do not spill anything on the system. The best way to avoid spills is to not eat or drink near your system. • Some products have a replaceable CMOS battery on the system board. There is • • a danger of explosion if the CMOS battery is replaced incorrectly.
Notice and Safety With Wireless - English V1.1.fm Page iv Friday, May 3, 2002 3:21 PM Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact an authorized service location.
Notice and Safety With Wireless - English V1.1.fm Page v Friday, May 3, 2002 3:21 PM Regulatory Compliance Statements Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device.
Notice and Safety With Wireless - English V1.1.fm Page vi Friday, May 3, 2002 3:21 PM In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated.
Notice and Safety With Wireless - English V1.1.fm Page vii Friday, May 3, 2002 3:21 PM United States of America Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Written by: Daryl L.
Notice and Safety With Wireless - English V1.1.fm Page viii Friday, May 3, 2002 3:21 PM The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on.
Notice and Safety With Wireless - English V1.1.fm Page ix Friday, May 3, 2002 3:21 PM If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Notice and Safety With Wireless - English V1.1.fm Page x Friday, May 3, 2002 3:21 PM Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada.
Notice and Safety With Wireless - English V1.1.fm Page xi Friday, May 3, 2002 3:21 PM Telecommunications per DOC notice (for products fitted with an IC-compliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users’ satisfaction.
Notice and Safety With Wireless - English V1.1.fm Page xii Friday, May 3, 2002 3:21 PM European Union The following information is only applicable to systems labeled with the CE mark .
Notice and Safety With Wireless - English V1.1.fm Page xiii Friday, May 3, 2002 3:21 PM European States qualified under wireless approvals: EU Austria, Belgium, Denmark, Finland, France (with frequency restrictions), Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden and the United Kingdom. Accept EU Iceland, Liechtenstein, Norway and Switzerland European States with restrictions on use: EU In France, the frequency range is restricted to 2446.5-2483.
Notice and Safety With Wireless - English V1.1.fm Page xiv Friday, May 3, 2002 3:21 PM Japan VCCI Statement This equipment is in the Class B category (Information Technology Equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment aimed at preventing radio interference in such residential areas.
Notice and Safety With Wireless - English V1.1.fm Page xv Friday, May 3, 2002 3:21 PM Prior to setting up your device: 1. Make sure that there are no other devices in your area using the same frequency band. 2. Change the channel, location, or discontinue device use if you are interfering with any other radio station. 3. Contact manufacturer if you have any problems with this device.
Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows® XP operating system. Whether you are new to using a portable computer or are an experienced user, this user’s manual can help you get the most from your computer. Manual Documentation Conventions Information Icons Three icons and their associated messages appear in this manual. The information icons are placed before the step/information they apply to: Warning: Indicates the possibility of personal injury.
CD-ROM Device Naming Convention In many installation programs you will have to get a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD. For instance, if you have one HDD with two partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.
Introducing Your Computer Your computer is a lightweight portable computer that includes features such as Dolby Digital & Dolby Home Theater System support, flex-bay, fingerprint recognition system (factory option), memory stick (factory option), wireless LAN module (factory option), Bluetooth module (factory option), CD/MP3 player (factory option) to meet your computing needs at home or on the road. (Figures may be different depending on options).
Buttons and LEDs User Defined Button E-Mail Button Internet Button Power Button HDD Access LED CD Access LED FDD Access LED Scroll Lock LED Number Lock LED Caps Lock LED Play/Pause & Track Indicator Volume Up Player Off/Stop/Eject Volume Down MP3/CD Player Option Battery Status LED Power LED Next/Fast Search-Forward Previous/Fast Search-Reverse Without MP3/CD Player Option 4 Users Manual Player On/Play/Pause
Right Side Flex-Bay Left Side Memory Stick Slot * Factory Option PC Card Slot Fan Vent PC Card Eject Button Headphone / S/PDIF Jack Modem Port LAN Port Microphone Jack Back Side Security Lock Port Fan Vent Parallel Printer Port PS/2 Port 1394 Port FIR * Factory Option USB Ports External Monitor Port Serial Port DC-In Port TV-Out Port(S-VHS, option) Introducing Your Computer 5
Bottom Flex-Bay Latch Flex-Bay Compartment Fan Vent Port Replicator Connector Battery Latch Battery 6 Users Manual Memory Compartment
Using Your Computer for the First Time This section gives you detailed information on using your computer for the first time. Turning On the Computer To turn on the computer’s power for the first time: 1. Install the battery and connect the AC adapter according to the Installation Guide. 2. Push the LCD open button and lift up the cover. Or if you do not have MP3/CD Player option, slide the LCD open latch to the right and lift up the cover. 3. Press and then release the power button.
Turning Off Your Computer Prior to shutting down your computer, ensure all of your data and current work are saved. The system will ask if you wish to save any unsaved work. Saving your work first will speed the shutdown process. To turn off the computer, complete the following steps: 1. Click on the taskbar. 2. Click Shut Down Computer to display the shutdown popup window. 3. Click Turn Off to complete the shutdown sequence.
Tips for Using Your Computer The following information helps you avoid potential problems as you use your computer: Do not try to disassemble your computer. Opening the system chassis voids your warranty. Only an authorised manufacturer service center can replace or add any parts inside the chassis. • Follow all the instructions and cautions in your computer user documentation. • The LCD has a polarized surface and can be damaged easily. To prevent damage, avoid touching the screen.
Travelling with Your Computer Air Travel If you are travelling by air, follow these tips: • Take the computer with you as carry-on luggage. Do not check the computer with your baggage. • Allow the computer and disks to go through the X-ray security devices. Do not hand-carry disks through the walk-through metal detectors, which can cause loss of data. • Make sure that the battery is charged or the power cord is easily accessible. You may be required to turn on the computer for airport security personnel.
Handling Spills Do not spill anything on your computer. The best way to avoid spills is to avoid eating and drinking around your computer. If you do spill something on your computer, turn off your computer, unplug it immediately, and do the following: • If you spill liquid on the keyboard, drain as much of the liquid from the keyboard as possible. Be careful not to let the liquid drip onto the LCD panel. Allow the system to dry for several days before trying to use it.
Using the Keyboard Your computer has an 88/89-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function & Special Purpose Keys Embedded Numeric Keypad Cursor/Screen Control Keys Application Key Function Key Windows Key Although the layout of the keys on your computer’s keyboard is different from that on a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you use it.
To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and the surface around the keys. Do not allow liquid to drip into the keyboard or you may damage the keyboard. Using the Numeric Keypad Your keyboard includes a numeric keypad, which is a group of keys that you can set to type numbers and mathematical symbols, such as the plus sign. A number or symbol on the left corner of each keypad key shows its numeric function.
Using Special Function Keys The function key activates special functions when it is pressed in combination with another keys. Table 2 shows the special key combinations. Table 2. Description of Special Function Key Combinations Key Combinations Key Name F2 Gauge Gauge Displays the gauge showing the power source, battery level, wireless on/off, and S/PDIF on/off. The gauge closes in a few seconds, or you can press to close the gauge.
Hot Keys You may program the three buttons to the left of the power button to start any program you have installed on your computer. User Defined Button Internet Button E-Mail Button The default settings for these buttons are: Internet Explorer Outlook Express Windows Calculator To reprogram the hot keys, follow the steps below: 1. Double-click displayed. icon on the Windows taskbar, the Key Setting window is 2.
Using the Touchpad Your computer is equipped with a touchpad, which is an integrated-pointing device that is used to perform standard mouse functions. The touchpad is an advanced and reliable pointing device that works with a touch of your finger. Touchpad Touchpad Buttons Scroll Button Four (4) Direction Scroll Button (Default is a 2 Direction Button) If you have purchased your computer without the CD/MP3 player option, your computer will have a four (4) direction scroll button.
d Action Process and Comment Click/Tap Process Depress the touchpad left button and release or position the pointer over the object and quickly tap the touchpad once with your finger. This action is called clicking. Comment This will cause a process to begin or select an object on the screen. Double-click/Tap Process Quickly click the left touchpad button two times or position the pointer over the object and Quickly tap the touchpad twice with your finger. This action is called Double-clicking.
Action Process and Comment Scroll Up Process Place your finger on the top half of the button to scroll up the current window. Comment Moves the current window down. Scroll Down Process Place your finger on the bottom half of the button to scroll up the current window. Comment Moves the current window up. Scroll Left Process Place your finger on the left half of the button to scroll left in the current window. Comment Moves the current window right.
Drag (Move) To move a window on the desktop, complete the following: 1. Click the window title bar of the window which you want to drag using the touchpad. 2. Press the left touchpad button and hold it. 3. Drag the window using the touchpad.
Reading the System Status Lights System Top System Status lights show the status of computer functions. LED Name Function HDD Access Blinking Green - HDD is being accessed. CD Access Blinking Green - CD is being accessed. FDD Access Blinking Green - FDD is being accessed. Caps Lock Changes all alpha or letter input into capital letters. No changes occur to numeric and special keys. Num Lock Changes a portion of the keyboard to a numeric keypad. See ”Using the Numeric Keypad” on page 13.
Connecting to the Internet This section explains how to connect you to the internet. For details on how to establish the connection contact the Internet Service Provider (ISP) or system administrator (SysAdmin). Connecting to the Internet Using a Modem Install the Modem cable by simply plugging the cable into the modem slot as shown in the figure below. Modem Cable (Minimum 26 AWG) 1. Contact your Internet Service Provider to obtain information or CD required to make the connection in your area. 2.
Precautions Before Use Country Selection Country Selection: Because your computer is very mobile you must ensure you select the country you are calling from is selected correctly, otherwise you may experience connection problems. To change the country selection proceed as follows: 1. Click Start > Control Panel > Network and Internet Connections. 2. Click Phone and Modem Options. 3. Click on the connection you wish to edit in the Locations: box. 4. Click Edit in the Dialing Rules Tab 5.
If you use a simple terminal program (i.e. hyper terminal): Type the “ATX3&W” or “ATX3” command as an initialization command. MODEM Notes: 1. In order to use the 56K feature, be sure to check if the standards supported by the on-line service provider and the modem are identical. 2. If you use a PBX phone system, you can not connect using the 56K mode. 3. Internationally connected calls will be limited to 33.6K (Max.
Configuring Network Environment Configure the Network Adapter as follows: 1. Click Start > Control Panel > Network and Internet Connections 2. Click icon (Network Connections). 3. Right-click the icon (Local Area Network) then click Properties button. 4. Select Internet Protocol (TCP/IP) in the “This connection uses the following items:” box. Intel(R) Pro/100 VE Network Connection 5. Click Properties. The TCP/IP Properties window opens. Step 7 Step 8 6.
Using Both DHCP and Static IP Simultaneously When you are alternatively using networks with either DHCP or static IP addressing, you can use both of the network connections without reconfiguring using alternative settings that enable simultaneous configurations of DHCP and static IP. This function is provided only when your operating system is Windows XP. 1.
Configuring Network Environment Settings for Wireless LAN A wireless network (Wireless LAN) environment is a network environment that enables communication between multiple computers at home or a small-size office through wireless LAN devices. Using the wireless network connections between the systems, you can use normal network functions such as sharing of files, folders and printers.
To turn wireless function on/off Press keys to turn wireless function on/off. Press keys to see if the wireless function is turned on( ) or off( ). Connecting to an Access Point (AP) This section describes how to connect to an AP. You can use the network when you are connected to an AP. In this section, the configuration procedures are described for Windows XP installed computers.
If the network key is not configured for the desired AP, select 'Allow me to connect to the selected wireless network, even though it is not secure’. Now you are connected to the AP, and you can access the network. Checking the connection status Move the mouse pointer over the Wireless Network Connection ( the taskbar, and the connection status is displayed.
2. Click Advanced. 3. On the Wireless Network tab, click Advanced. 4. Clear 'Automatically connect to non-default network' check box, if it is selected. Select 'Computer-to-computer (ad hoc) networks only', and click Close. 5. In the Wireless Networks tab, click Add.
6. Enter the network name (e.g. samsung), and unselect 'The key is provided for me automatically'. Enter the encryption key in the Network key field, and click OK. To prevent a network connection from an unauthorized user, it would be better to configure a network key (encryption key). A network key consists of 5 or 13 alphanumeric characters (e.g. magic), or of 10 or 26 hexadecimal numbers (a hexadecimal number is represented by numbers '0' to '9' or letters 'a' to 'f').
7. Check that the configured network name (e.g. samsung) is in the ’Preferred networks’ item, and click OK. Now your wireless network setup has been completed. Step 2. Connecting to the configured computer 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks. ) icon on the taskbar, and 2. Select the wireless network name (e.g.
If the network key is not configured in ”Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 28, select 'Allow me to connect to the selected wireless network, even though it is not secure'. The two computers are connected and are able to communicate with each other. When the computers are connected, the 'Wireless Network Connection' message is displayed for a short time over the Wireless Network Connection icon of the two computers.
Using Networks in Other Operating Systems This section describes the wireless network configuration procedures for operating systems other than Windows XP. You can connect to the network by completing the following steps. • Step 1. Install the 'Wireless Client Manager' program. • Step 2. Set up a network in the target computer. To connect two computers with a computer-to-computer (peer-to-peer) network, the following procedures have to be completed for both computers. Step 1.
5. Enter the desired network name (i.e. AP name) in the 'Identify Your Network' window, and click Next. If you do not know the network name when you connect to the AP, click the Scan button, and select the name from the displayed name list. When configuring a computer-to-computer wireless network, all target computers have to specify the same network name. 6.
Using Network Services While the computer is connected to the network, you can use network services to share files, folders, and printers. Using computer-to-computer wireless networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet. Network services are provided for the computers that are connected to the network through wired or wireless network connections.
Step 1. Configuring Sharing 1. Right-click the target file or folder to share in My Computer, and select Sharing and Security. 2. Click 'IF you understand the security risks but want to share files without running the wizard, click here'. It has the same security effect as that of the 'Network Setup Wizard'. This screen does not appear if Internet Sharing Network Wizard has been installed in the computer-to-computer wireless network environment. 3. Select 'Just enable file sharing', and click OK. 4.
Step 2. Using Shared Files or Folders This section describes how to access shared files or folders if your computer is a member of the same workgroup. 1. Click Start > My Computer. Under Other Places, click My Network Places in your computer. 2. Click 'View workgroup computers', and click the desired computer to access the shared file. If your computer is a member of another workgroup: 1. Click Other Places > Microsoft Windows Network. 2. Click the desired workgroup. 3.
Step 1. Configuring Printer Sharing 1. From the computer connected to the printer, click Start > Printers and Faxes. 2. Right-click the printer you want to share, and click Sharing. 3. Select 'Share this printer', enter a share name for the shared printer, and click OK. 4. In the Printers and Faxes window, you will find the printer icon has been changed to another icon on a hand. Step 2. Adding and Using a Shared Printer. 1.
5. Select 'Browse for a printer', and click Next. 6. Select the workgroup or computer, select the desired printer, and click Next. If you cannot find the desired printer, try again after a while. 7. Read the warning about a shared printer, and click Yes to install the shared printer. 8. Select Yes for 'Do you want to use this printer as a default printer?', and click Next. 9. Click Finish. 10.
Sharing an Internet Connection Using computer-to-computer (peer-to-peer) network connections, you can access the Internet through a computer connected to the Internet even if your computer is not directly connected to the Internet. To share an Internet connection, the computers should be connected to a computer-to-computer (peer-to-peer) wireless network. For details, see “Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 28.
If the computer is connected to the Internet through a wired LAN, select 'Local Area Connection'. 3. On the Advanced tab, select 'Allow other network users to connect through this computer's Internet connection', and click OK. Step 2. Checking the Shared Internet Connection. When the Internet connection sharing configuration has been completed, the network icon in the Network Connections window is displayed as follows: Click Start > Control Panel > Network and Internet Connections > Network Connections.
Using the Flex-Bay The flex-bay provides an impressive array of secondary storage devices listed below. These are available as an option for your computer. • • • • • • • • CD-ROM drive CD-RW drive DVD-ROM drive CD-RW/DVD-ROM combo drive DVD multi drive FDD drive 2nd HDD drive Weight Saver If your operating system is Windows, you must install the Softex Bay Manager software on the software CD in order to use the Bay Manager Utility to swap the devices while the power is on.
Swapping a Flex-Bay Device - Power Off To remove a device with the power off proceed as follows: 1. Turn the computer’s power off. 2. Tilt the computer up and locate the flex-bay latch. 3. Slide and hold the latch toward the rear of the computer. 4. Slide the device out. 5. Carefully slide the new device into the bay. 6. Push the device in until it is flush with the chassis and the flex-bay latch snaps into place.
To swap a device with the power on proceed as follows: 1. Start the Softex Bay Manager Utility. You do not have to turn the computer over or tip it on its side to change devices. Simply tilt the computer up about 10 cm at the back and locate the Flex-Bay latch. See Figure below for the location of the Flex-Bay latch. The computer in the figure is turned over for clarity. Flex-Bay Latch 2. Click Remove / Swap.
Using the Disk Drives To use the Floppy drive or the CD-ROM drive you must verify it is installed in the flexbay slot. To swap devices see “Using the Flex-Bay” on page 42. Using the Floppy Disk Drive (Option) To use a floppy disk in your computer, insert it into the floppy drive. Floppy Disk Eject Button To remove a floppy disk, press the floppy disk eject button on the front of the floppy drive. To protect the data on your floppy disks, follow the manufacturers guidelines.
1. Press the button on the CD-ROM drive, and the tray slides out. (Do not lean on the tray; because it will not support much weight.) CD-ROM Drive Warnings: Do not place reflective objects other than the CDs in the disk slot because of possible hazardous laser emissions. The laser beam used in this CD-ROM drive is harmful to the eyes. Do not attempt to disassemble the CD-ROM drive. Refer servicing to your authorized service center. Do not touch the CD lens, doing so may damage the device.
Using the Memory Stick (Factory Option) The memory stick is a factory option that will increase your computer storage capacity as well as increase data portability. The memory stick may used in many types of equipment such as digital cameras and PDAs for example. Memory Stick and are a trademarks of the Sony Corporation. Memory Stick Support The Magic Gate model is not currently supported.
Using the Memory Stick The memory stick is used the same as the FDD drive on your computer but with much larger capacity, currently up to 128MB. Formatting the memory stick The memory stick may need to be formatted before use, if so insert it into the slot and format it the same as the FDD Drive. Protecting Data on the memory stick To prevent overwriting/deleting your data in the memory stick, move the slide lock to the “Lock” position. to see the contents of the memory stick: 1.
Working with PC Cards By installing PC cards, you can add functions to your notebook computer similar to those found on add-in boards for desktop computers. Available PC cards include: • Input/output, such as modem, network, video capture, and SCSI cards. • Storage, such as hard drive and flash memory cards. Your computer includes the following PC card support: • One PC-card slot: You can install PCMCIA type I or II cards in the slot.
Using PC Cards To insert a PC card into a slot: 1. Push the slot door in with the PC card. 2. Align the card with a slot and insert the card into the slot until it locks in place. PCMCIA Card Eject button PC Card : Insert PC card with product information facing up Windows automatically assigns computer resources (such as communication ports and memory addresses) to a PC card installed in your computer.
Multi Media Functions/Equipment Media Player The Windows Media player is used to play audio files while the computer is on. You can play audio/video CD files using the Windows Media Player, as well as watching TV, video and listening to the radio through internet. The instructions to play a video CD-ROM are the same as the instructions for the audio CD below. Playing a Audio/Multimedia CD To play an CD follow the instructions below: 1. Insert a compact disc into your CD-ROM drive. 2.
MP3/CD Player (Factory Option) The MP3/CD Player can play music CDs and MP3 files while the computer is off. It will not, however play video CDs. Button Operation The buttons and display for the MP3/CD Player operate as follows: Button + + + 52 Users Manual Name Function Volume Down Decreases speaker volume when MP3/CD Player is on. Volume Up Increases speaker volume when MP3/CD Player is on. Mute Press the buttons simultaneously for 1 sec. to mute the sound.
Using the MP3/CD Player Play an Audio CD 1. Verify the computer is off and that a CD-ROM device is in the flex-bay. Player On/Play/Pause Button: If a CD-ROM device is not in the flex-bay, the Player On/Play/Pause button button will not turn on the MP3/CD Player. Computer Button Operation: MP3/CD Player buttons are not functional when the system is turned on. To use the MP3/CD Player buttons while the system is on, you must start the Windows media player. 2.
Dolby Digital & Home Theater System (S/PDIF Port) This product supports 5.1 channel output, which is a basic function for home theater systems and DVD drives. It provides 3D surround sound and a vivid screen. Home theater system usually consists of a TV, DVD, 5.1 channel speakers, and a digital amplifier to provide a high-resolution vivid (MPEG2) picture and 3D surround sound (Dolby 5.1 or DTS).
2. Connect the speakers to the digital amplifier. TV Sub Woofer Digital Amplifier Front Right Speaker Front Left Speaker Computer Center Speaker Surround Left Speaker Surround Right Speaker If your computer supports a TV-Out port, you can connect and enjoy a large screen. After connecting the TV, you will need to select the TV as the display device using the Windows Display Properties window. After making all connections, ensure you enable S/PDIF: 1. Enable S/PDIF in Windows. 2.
Enabling S/PDIF on the DVD Program When using 5.1 channel speakers, you will need to install the “Power DVD” program on the DVD Installation CD (supplied separately) and then set it up as described below: 1. Run the “Power DVD” program and click the settings button, the configurations window pops up. Settings Button 2. On the Audio tab, change the Audio Output setting to “Use SPDIF” and click OK. 3. You are ready to enjoy your home theater system with your own DVD’s.
Volume Control The instructions below are for controlling speaker volume when the computer is on. To control speaker volume when the MP3/CD Player only is on, see “MP3/CD Player (Factory Option)” on page 52. Using the Keyboard Changing the volume with your keyboard. Use to decrease the volume or to increase the volume. Using the Volume Control Icon Double-click icon on the taskbar. The Volume Control window pops up. Use this window to adjust the volume.
Using the Battery Your computer uses a smart rechargeable Lithium-ion (Li-ion) battery pack for power when the AC adapter is not attached to an electrical outlet. The smart battery gives an accurate measurement of the current battery capacity which helps extend operating time by enabling effective power management in operating systems that take advantage of the accurate information supplied by the battery.
Safely Using the Battery Follow these guidelines to safely use the battery: • Turn off your computer and unplug it if you accidentally: – Expose the equipment to liquid. – Drop, jar, or damage the computer. • Use only approved battery chargers. • Do not disassemble the battery, heat it above 100°C, or burn it. The battery used in this computer may cause a fire or chemical burn if mistreated. • Your computer's rechargeable battery may be considered hazardous waste.
Installing the Battery To install the battery pack: 1. With the computer’s power off, close the LCD panel and turn the computer over so the bottom of the unit faces up. Insert the battery into the battery compartment, ensuring the correct orientation so that the battery fits in its slot properly. 2. Place the battery inside and against right side of the computer battery compartment at an angle of approximately 30 degrees. 3. Push the battery down until the latch snaps into place, securing the battery.
Monitoring the Battery Charge Battery life is affected by factors such as the power-management settings in System Setup, the applications you use, and the brightness settings of the LCD. Under normal usage, the battery charge lasts approximately 2.5 hours. Battery life estimates are subject to variation. The actual life of your battery may be less than the estimates given in the manual. You can monitor the charge of the battery pack installed in your computer by using the Power Meter or Battery Gauge.
Battery Gauge You may display the battery gauge while you are in any program by pressing . While the battery gauge is being displayed, all keys except are disabled. The battery gauge is only displayed for a few seconds. Power Source: Indicates that the computer is powered by the AC adapter. Indicates that the computer is powered by the battery. Battery Level: Indicates the approximate amount of the primary battery charge remaining. Indicates the computer is on AC power only.
Battery Warnings If the battery charge is low (about 10%) you have 5–10 minutes of battery life left. You should: • Save your work and, • Connect the power cord to the computer or turn off the computer and install a fully charged battery. You can adjust the battery alarm features by using the operating systems power management program (Start > Control Panel > Power Options in Windows).
Using System Setup The System Setup (BIOS) program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in battery-maintained CMOS memory that saves the information even when the computer’s power is turned off. When your computer is turned back on, it is configured with the values found in this memory. Run System Setup if you get a message prompting you to run the program.
Table 4. System Setup Navigation Keys Navigation Key Function Displays the General Help window. Exits the current menu. or Moves the cursor up and down between fields. or Selects different menus. Pressing the key at the Main menu brings you to the Exit menu. Scrolls backwards through the options for the highlighted field. Scrolls forward through the options for the highlighted field.
Changing Booting Priority The Boot menu in system setup enables you to select the booting device and to set booting options. Boot Device Priority field enables: You to select the order in which the computer attempts to boot from different devices. The field has three options: CD-ROM Drive, Removable Devices, and Hard Drive. To change the booting device priority, choose the device positions by completing the following: 1. At startup, press to open System Setup. 2. Use to select Boot menu.
Configuring the Password Setting the Supervisor Password By configuring a supervisor password, you can restrict system access to authorized users only. To use a fingerprint in the fingerprint sensor installed model, refer to the supplied manual for the fingerprint sensor. 1. Select the Security menu in the System Setup. To enter System Setup, see “Using System Setup” on page 64. 2. On the Set Supervisor Password item, press . 3.
Activating the Booting Password Before activating the booting password, the supervisor password must have been configured. On the Password on boot item, press or to set the option to [Text Password]. If you have fingerprint sensor installed, you can set the option to [Finger Print] to boot the computer with your fingerprint. From now on, system booting will not proceed without the password. Deactivating the Password 1. On the password to delete, press . (e.g. supervisor password) 2.
Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance. Your computer runs fastest with the power cord attached, when power management is disabled. In the next sections, basic and advanced methods of power management will be discussed.
3. Click the Power Schemes tab to display the basic power management options. Power Schemes Tab 4. Select the time that you wish each of the following actions to occur in Battery and AC power mode. • • • • Turn off monitor: Turn off hard disks: System standby: System hibernates: Turning off the monitor and HDDs will save a substantial battery power, therefore when in battery only mode, select the shortest time practical.
If You Reinstall Windows: You should re-establish hibernate in power options by opening Power Options Properties window and click on the Hibernate tab then click “Enable Hibernation”. Hibernate Tab Frequent Interruptions: If you experience frequent interruptions, you might also consider putting your computer into automatic hibernation after a specified number of minutes using the power management options.
Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Control Panel > Performance and Maintenance. 2. Click icon to display the Power Options Properties window. 3. Click the Advanced tab to display the advanced power management options. Advanced Tab Power & Sleep Button Programming Windows 4.
Using the Hard Drive Your computer includes a removable IDE (integrated drive electronics) hard drive. The IDE hard drive can store the data and programs your computer uses. The drive plugs into a connector on the system board. The hard drive that comes with your computer has already been formatted. Do not format the hard drive. Doing so destroys all data contained on the drive.
Video Features and Configuration Resolution and Colour Depth The resolution of the LCD is the sharpness of the image it can display. Resolution is measured by the number of pixels (individual dots) displayed on the entire screen. In general, the more pixels the LCD can display, the better the image. The number of colours the LCD can display is measured by how many bits the LCD uses to represent each pixel: • 16-bit colour can support 64 K (65,536) colours. • 32-bit colour can support 16 M (16.
Configuring Display Features The following sections describe how to configure the display settings on your computer. Display Resolution Notes: When Windows XP is initially installed it will automatically adjust the resolution to maximum available. Changing Colour Depth and Resolution To change the colour depth and resolution of your LCD: 1. Click Start > Control Panel > Appearance and Themes. 2. Click icon. The Display Properties window appears. 3. Click the Settings tab. The Settings screen appears. 4.
Using External Display Devices Using external display devices such as a monitor, projector, TV, etc allows you to view screen images alternatively or simultaneously on each device. You can also split a screen into two display devices, or view different images on each display device. Using external display devices is especially useful when you are giving a presentation or watching a movie through your TV.
Using Dual View to View Extended Screen You can expand the screen into two display devices and work conveniently in separate workspaces. In Dual View mode, you can select the screen resolution and color quality for each display device, as if there were two separate graphics cards. 1. Connect the external display device (e.g. a monitor or a projector) to the corresponding port of the system. To connect a TV, connect the TV to the TV output port of the system. 2.
4. Click OK. The primary display device(the LCD) is indicated as '1', and the secondary display device is indicated as '2'. Now you can use each of the two display devices as independent display devices. 1 : Primary 2 : Secondary When using Dual View, it is recommended that LCD is kept as '1', the primary display device.
Using Options You can select these options at purchase: • Wireless communication module (802.
Memory Modules You can increase system memory by installing optional memory modules. You can install a 128, 256 or 512 MB modules. To avoid possible system problems, use only approved memory modules in your computer. Before You Install Memory To prevent personal injury and damage to the equipment, follow the precautions listed here before installing a memory module.
Installing a Memory Module Handle a memory module carefully. Hold them only by the edges. To install a memory module: 1. Turn the computer over so that the bottom faces up. 2. Using a screwdriver, remove the screw that holds the memory-module compartment door in place. 3. Grasp the edge of the door and pull the door off the chassis. Memory Module Precautions: When removing the module, pull on the plastic portion of the connector slots tabs only.
5. Align the connector on the memory module with the connector of the slot. 6. Push the memory module into the slot at a slight angle (~45o) until the connectors are fully engaged. 45o 7. Push down on the edge of the memory module until the module snaps into place. 8. Align the memory module compartment door with the compartment and push the door down until it snaps into place. 9. Reinstall the screw you removed in step 2.
FIR (Fast Infrared) Connection FIR Technology Limitation The transmitter and the receiver should be no more than 50cm apart. System Setup The system setup setting must be completed first in order for the option to operate properly. 1. At startup, press to open System Setup. 2. Use to select the Advanced menu. 3. Highlight the I/O Device Configuration option with or keys and press . 4. Highlight the FIR port with the or keys. 5.
Troubleshooting Complete the following in the order presented until your system is functioning properly. If all of the steps below fail then contact your local reseller for assistance. Questions and Answers Please see “Questions and Answers” on page 85. for assistance in correcting any computer operational problems. Check the Connections Verify all of the power and peripheral cables are securely plugged into their sockets and that your system and power supply is on.
Questions and Answers This section provides information on possible problems, solutions and other references for system use. Windows Related Q1 The system does not shutdown properly. A When the system does not shutdown normally, press and hold the Power button until the system manually shuts off. If the Power-Saving Mode is configured into the Power button, press and hold for more than 4 seconds to shut the system off.
Q3 How to remove graphics driver? A Graphics drivers of both 'ATI Control Panel' and 'ATI Display Driver''. In the 'Add/Remove Programs' menu, remove 'ATI Control Panel', and remove 'ATI Display Driver' in order without rebooting the system. Please reboot the system after removing 2 drivers. Q4 In the following cases, the screen flickers or displays noise.
2. Select Hardware tab > Device Manager > Modems in the System Properties window, and check if there is a yellow exclamation mark on the installed modem icon. If there is, delete the modem device driver and reinstall the driver, because the yellow exclamation mark represents a not properly installed driver. 3. If there is no yellow exclamation mark, double-click the installed modem, and click Diagnostics tab > Query Modem in the Modem Properties window to diagnose the modem.
3. In the Modems tab, select the installed modem, and click Properties. 4. In the Modem tab of the Modem Properties window, clear the 'Wait for dial tone before dialing' check box. 5. When the configuration is completed, click OK. Q3 How do I use my modem when dialing from overseas? A1 Check that the modem is correctly configured according to the current country.
Game and Program Related Windows might not support some functions or might cause driver compatibility problem while running some application software, especially games. For more information about the latest driver, and bug fixes, refer to our home page. Q1 While running 3D program, pressing key combination to toggle display devices dose not work. A Pressing key combination while running 3D programs, may cause an error.
to connect should be the same in all computers. The network name is case sensitive, if the name contains letters. A2 If you are using a network key (encryption key), an AP (Access Point) and a computer-to-computer network (peer-to-peer), you have to use the same network key. The network key of the AP is configured in the AP management program. Ask your network administrator for more detailed information. A3 Check that the device driver is properly installed.
Q4 I cannot connect to the AP wireless network. A1 Check the wireless LAN radio environment. Using a wireless LAN may be restricted by the surrounding radio environment, and the distance between wireless stations. Also obstacles such as walls or doors may affect wireless LAN connections. A2 Check that the AP is operating properly. Turn the AP off, and turn it on after a short wait. A3 Check that the network key (encryption key) configuration for the AP is correct.
- Windows 2000 service pack 2: http://support.microsoft.com/default.aspx?scid=kb;en-us;296872 - Windows 2000 service pack 3: http://support.microsoft.com/support/kb/articles/Q327/9/47.asp Q7 The Wireless network connection operates properly, but the Wireless Network Connection icon on the Taskbar displays the "Disconnected" message. A This is one of the known problems when you are using a wireless LAN connection after installing Windows XP service pack 1.
Reinstalling Software If you have reinstalled the Windows operating system, or the system and program do not operate properly, you can re-install the driver and program using the system software CD. The drivers and programs included in the system software CD are listed in the D:\ReadMe.htm file. (Provided that the name of CD-ROM drive is "D".) Running the system software CD Insert the system software CD into the CD-ROM drive. The initial screen appears automatically.
Installing programs 1. In the initial screen, click Install programs. 2. Click Standard installation in the program installation screen (standard installation is recommended). • Standard installation: Installs and recovers programs to the state of shipment. • User installation: You can select the program installation location, and other options for the program installation.
Reinstalling Windows XP If the Windows XP does not operate properly due to an error in the system, or if you have replaced the hard disk drive, you can reinstall Windows XP using the system recovery CD. With the system recovery CD, you can reinstall Windows XP only. To return the system to the state of shipment, reinstall the device drivers and programs with the system software CD after reinstalling Windows XP with the system recovery CD.
3. The description for the standard installation appears. Click Yes. The installation starts, and the system will be restarted after a while. 4. After the system has restarted, the message ’Press any key to boot from CD’ appears. Do not press any key at this time. After a while the partition configuration screen appears. To not change the partition, press . What is partition configuration? Partition configuration is a function that devides the hard disk drive into one or several partitions.
If You Cannot Run Windows If you cannot run Windows, you have to boot the system with the system recovery CD, and reinstall Windows. If you boot the system from the system recovery CD, you can install Windows only with the user installation option. You cannot install with the standard installation option. 1. Insert the system recovery CD into the CD-ROM drive and start the computer. 2. If the following message appears on the screen, press any key from the keyboard. Press any key to boot from CD.....
Specifications The following is the basic hardware specification for the purchased product. Variations may exist depending on the model type. Item Specification CPU Intel Pentium 4 1.4~2.2 GHz Remarks Cache memory 512KB PBSRAM Main memory 128/256/512 MB DDR SDRAM, 2 DDR socket Main Chipset Brookdale-M Chipset Maximum 1GB Hard disk drive (HDD) 2.5’’, UltraDMA 100, S.M.A.R.T 9.
Wireless LAN Specification Name of the Registered Equipment : Special Low Output Wireless Device For Wireless Data Communication Systems. Item Physical Specifications Detailed Specifications Dimensions (Width X Height) 59.75 X 50.95 mm operation temperature and humidity Same as system operation Temperature: 0°C ~ 40°C Humidity: less than 95% Power Specification Network Specifications Power Saving Mode 45mA Receiving Mode 250mA Transmission Mode 350mA Power 3.3V +/- 0.
Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country. In France however, use only 4 channels (channel 10, 11, 12, 13) when using wireless networks. • Standard: IEEE 802.
Abbreviations A . . . . . . . . . Amperes AC . . . . . . . . Alternating current ACPI . . . . . . Advanced Configuration and Power management Interface APM . . . . . . Advanced Power Management ATA. . . . . . . AT attachment (refers to the hard-drive interface in an ATcompatible computer) ATAPI. . . . . AT attachment packet interface BBS . . . . . . . Bulletin board system BIOS . . . . . . Basic input/output system C . . . . . . . . . Centigrade CD . . . . . . . . Compact disc CD-ROM . .
ISA . . . . . . . Industry Standard Architecture KB . . . . . . . . Kilobytes kg . . . . . . . . . Kilograms LAN. . . . . . . Local-area network lb.. . . . . . . . . Pounds LBA . . . . . . . Logical block addressing LCD. . . . . . . Liquid-crystal display m . . . . . . . . . Meters mA . . . . . . . . Milliampere mAhr . . . . . . Milliampere hour MB. . . . . . . . Megabyte mm . . . . . . . millimeter MPEG . . . . . Motion Picture Experts Group MPU . . . . . . Microprocessor unit ms . . . . . . . .
Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts). The 32-bit cards can transmit more data at a time than the 16-bit cards, thus increasing their speed. CMOS memory CMOS (complementary metal oxide semiconductor) memory is powered by the CMOS battery.
Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer. Because hard drives in notebook computers are smaller than those in desktop computers, their maximum storage capacity may be less than that of desktop hard drives.
PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed. Pixel A pixel is an individual dot in a graphic displayed on your computer. The pixels are so close together that they look as though they are connected.
Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer. TFT (thin film transistor) LCD A TFT LCD uses a separate transistor circuit to control each pixel. This technology provides the best resolution for an LCD screen. A TFT LCD is also sometimes called an active matrix LCD.