User Manual
Contents Chapter 1. Getting Started 3 5 20 23 28 Before You Start Safety Precautions Proper Posture During Computer Use Overview Turning the Computer On and Off Chapter 2. Using Windows 32 33 35 37 42 43 What is Microsoft Windows? Screen At a Glance Using the Charms Using Apps Windows Hot Key Function Using a Touch Screen (Touch screen models only) Chapter 3.
Chapter 1.
Before You Start Before reading the user manual, first check the following information. •• Optional items, some devices and software referred to in the user manual may not be provided and/or changed by upgrade. Note that the computer environment referred in the user manual may not be the same as your own environment.
Before You Start Copyright Chapter 1 Getting Started 4 About the Product Capacity Representation Standard © 2013 Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. owns the copyright of this manual. About the capacity representation of the storage No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, without the consent of Samsung Electronics Co., Ltd.
Safety Precautions For your security and to prevent damage, please read the following safety instructions carefully. Since this is commonly applied to Samsung computers, some pictures may differ from actual products. Chapter 1 Getting Started 5 Do not install the computer on a slant or a place prone to vibrations, or avoid using the computer in that location for a long time. This increases the risk that a malfunction or damage to the product will occur.
Safety Precautions Chapter 1 Getting Started Warning Failure to follow instructions marked with this symbol may cause personal injury and even fatality. Power Related The power plug and wall outlet figures may differ depending on the country specifications and the product model. Do not touch the main plug or power cord with wet hands. G If the power cord or power outlet makes a noise, disconnect the power cord from the wall outlet and contact a service center.
Safety Precautions Warning Chapter 1 Getting Started 7 AC Adapter Usage Precautions Failure to follow instructions marked with this symbol may cause personal injury and even fatality. Connect the power cord to an outlet or multiple power plug (extended cable) with a ground terminal. Failure to do so may result in electric shock. When the power supply is ungrounded, the current may leak resulting in electric shock.
Safety Precautions Warning Failure to follow instructions marked with this symbol may cause personal injury and even fatality. Battery Usage Related Please charge the battery fully before using the computer for the first time. Keep the battery out of the reach of infants and pets, as they could put the battery into their mouths. There is a danger of electric shock or choking. Use an authorized battery and AC adapter only. Please use an authorized battery and adapter approved by Samsung Electronics.
Safety Precautions Warning Failure to follow instructions marked with this symbol may cause personal injury and even fatality. Never heat the product (or battery) or put the product (or battery) into a fire. Do not put or use the product (or battery) in a hot location such as a sauna, inside a vehicle exposed to the heat, and so on. There is a danger of an explosion or fire. Take care not to allow metal objects such as a key or clip to touch the battery terminal (metal parts).
Safety Precautions Warning Failure to follow instructions marked with this symbol may cause personal injury and even fatality. Usage Related Disconnect all cables connected to the computer before cleaning it. If your notebook is an external & removable battery type, remove the external battery. There is a danger of electric shock or damage to the product. Do not connect a phone line connected to a digital phone to the modem. There is a danger of a electric shock, fire or damage to the product.
Safety Precautions Warning Failure to follow instructions marked with this symbol may cause personal injury and even fatality. Upgrade Related Be sure to upgrade the computer by yourself only if you have sufficient knowledge and ability. If this is not the case, ask for assistance from the service center or an authorized engineer for the upgrade. Be sure to upgrade only the parts specified in the user manual according to the procedures described in the user manual.
Safety Precautions Warning Failure to follow instructions marked with this symbol may cause personal injury and even fatality. Security and Movement Related Follow the instructions for the relevant location (e.g., airplane, hospital, etc.) when using a wireless communication device (wireless LAN, Bluetooth, etc.). Avoid exposing a drive to magnetic fields. Security devices with magnetic fields include airport walk-through devices and security wands.
Safety Precautions Caution Failure to follow instructions marked with this symbol may cause slight injury or damage to the product. Chapter 1 Getting Started 13 Battery Usage Related Dispose of worn-out batteries properly. •• There is a danger of fire or explosion. Installation Related Do not block the ports (holes), vents, etc. of the product and do not insert objects. Damage to a component within the computer may cause electric shock or fire.
Safety Precautions Caution Failure to follow instructions marked with this symbol may cause slight injury or damage to the product. Usage Related Do not place a candle, light a cigar, etc. over or on the product. There is a danger of fire. Use a wall outlet or multi-plug with a grounding part. Failure to do so may cause electric shock hazard. Make sure to have the product tested by a safety service engineer after repairing the product.
Safety Precautions Caution Failure to follow instructions marked with this symbol may cause slight injury or damage to the product. Chapter 1 Getting Started 15 Do not place your face close to the Optical Disk Drive tray when it is operating. There is a danger of injury due to an abrupt ejection. Check CDs for cracks and damage prior to use. If the computer emits smoke, or there is a burning smell, disconnect the power plug from the wall outlet and contact a service center immediately.
Safety Precautions Caution Failure to follow instructions marked with this symbol may cause slight injury or damage to the product. Chapter 1 Getting Started 16 To connect a device that is not manufactured or authorized by Samsung Electronics, inquire at your service center before connecting the device. There is a danger of damaging the product. Upgrade Related Carefully touch a part or device of the product. Failure to do so may result in damage to the product or injury.
Safety Precautions Caution Failure to follow instructions marked with this symbol may cause slight injury or damage to the product. Cautions on Preventing Data Loss (Hard Disk Management) Take care not to damage the data on a hard disk drive. •• A hard disk drive is so sensitive to external impact that an external impact may cause loss of data on the surface of the disk.
Safety Precautions Using the Power Supply in an Airplane Since the power outlet type differs depending on the type of airplane, connect the power appropriately. Since the representative figures of the power plug and the auto adapter are used, they may differ from the actual parts. Chapter 1 Getting Started 18 When Using the AC Power Plug Connect the power plug pins perpendicular into the center of the power outlet.
Safety Precautions Chapter 1 Getting Started When Using the Auto Adapter When a cigar socket is provided, you have to use the auto adapter (optional). Insert the cigar plug of the auto adapter into the cigar socket and connect the DC plug of the auto adapter to the power input port of the computer. Auto Adapter DC Plug Cigar Plug In-flight Cigar Socket When Using the Airplane Charging Coverter Depending on the airplane, you have to use the auto adapter and charging converter.
Proper Posture During Computer Use Chapter 1 Getting Started 20 Maintaining a proper posture during computer use is very important to prevent physical harm. •• Do not use the computer while you are lying down, but only while you are sitting down. The following instructions are about maintaining a proper posture during computer use developed through human engineering. Please read and follow them carefully when using the computer. •• Do not use the computer on your lap.
Proper Posture During Computer Use Chapter 1 Getting Started Eye Position Hand Position Keep the monitor or LCD away from your eyes by at least 50cm. Keep your arm at a right angle as shown by the figure. •• Adjust the height of the monitor and the LCD screen so that its top height is equal to or lower than your eyes. •• Avoid setting the monitor and LCD excessively bright. •• Keep the monitor and LCD screen clean. •• If you wear glasses, clean them before using the computer.
Proper Posture During Computer Use Chapter 1 Getting Started 22 Volume Control (Headphones and Speakers) Use Time (Break Time) Check your volume first to listen to music. •• Take a break for 10 minutes or more after a 50-minute period when working for more than one hour. Illumination Check your volume! •• Do not use the computer in dark locations. The illumination level for computer use must be as bright as for reading a book. •• Indirect illumination is recommended.
Overview Chapter 1 Getting Started 23 Front View •• The pictures used for the cover and the main body in the User Manual are those of the representative model of each series. Therefore the colors and appearance of the pictures may differ from the actual appearance of the product depending on the model. 1 Camera operating indicator 2 Camera •• The actual color and appearance of the computer may differ from the pictures used in this guide.
Overview Chapter 1 Getting Started 24 Status indicators and sensors (Optional) 1 Power 2 1 2 3 Charge Status 4 3 Caps Lock This shows the computer operating status. On: When the computer is operating. Blinks: When the computer is in Sleep mode. This shows the power source and the battery charge status. Green: When the battery is fully charged or the battery is not installed. / Red or orange: When the battery is being charged.
Overview Chapter 1 Getting Started 25 Right View 1 Monitor Port 1 2 3 A port used to connect a monitor, TV or projector supporting a 15pin D-SUB interface. You can connect a VGA adapter (optional). 4 2 Ear-set / headset Jack This is the jack for connecting an ear-set or headset. 3 USB Port You can connect USB devices to the USB port such as a keyboard/mouse, digital camera, etc. 4 Security Slot You can secure the computer by connecting a lock and cable to the Security Slot.
Overview Chapter 1 Getting Started 26 Left View 1 DC Jack A jack to connect the AC adapter that supplies power to the computer. This is a chargeable USB port that can be used to connect and charge a USB device. 1 2 3 4 5 Chargeable USB 3.0 2 Port What is a chargeable USB port? •• USB device accessing and charging functions are supported. 3 Micro HDMI Port •• The USB charging function is supported regardless of whether the power is turned on or off.
Overview Chapter 1 Getting Started Bottom View 1 1 Speaker A device used to generate sound.
Turning the Computer On and Off Chapter 1 Getting Started 28 Turning the computer on 1 2 3 Connect the AC adapter. Lift the LCD panel up. Press the Power button to turn the computer on. About Windows Activation When you turn the computer on for the first time, the Windows activation screen appears. Follow the activation procedures according to the instructions on the screen to use the computer.
Turning the Computer On and Off •• Since the procedures to turn the computer off may differ depending on the installed operating system, please turn the computer off according to the procedures for the áᔪ purchased operating system. •• Save all your data before clicking on Shut down. Ŗᮁ Open the Charms. • Touch screen:᯲ Swipe inward from the right edge. • Touchpad/mouse: Drag the mouse pointer to the top- or the bottom-right corner of the screen.
Turning the Computer On and Off Unlocking the screen To unlock the lock screen, do one of the following: •• Touch screen: Swipe the lock screen from bottom to top. •• Touchpad/mouse: Click the lock screen. •• Keyboard: Press any key. If the account has a password, enter the password to log in after unlocking the screen.
Chapter 2.
What is Microsoft Windows? Microsoft Windows is an operating system that is required for operating a computer. To use your computer optimally, you need to know how to use it properly. To learn how to use the operating system, check out Windows Help and Support, and Help+Tips. Chapter 2 Using Windows Viewing Help+Tips On the Start screen, select Help+Tips. •• The screen may appear somewhat different depending on the model and the operating system. •• This manual is designed for Windows 8.
Screen At a Glance Chapter 2 Using Windows Windows provides both the new Start screen mode and the Desktop mode of the existing OS. Start screen When you turn on the computer, the Start screen is displayed, which allows you to use the applications (Application, App, hereafter referred to as an App) at the same location. 1 1 Start Screen Refers to the default Start screen of Windows. 2 App Refers to the apps that are currently installed.
Screen At a Glance Chapter 2 Using Windows Desktop This provides similar functions to those provided by the desktop in prior Windows 8 versions. 1 2 3 3 Charms This refers to the menu that allows you to use functions such as Search, Share, Start, Device and Settings. Move to the Start screen. 4 Start button Right-click the button or tap and hold it to select quick access menus such as Shut down and Control Panel.
Using the Charms Chapter 2 Using Windows The Charms is a new type of menu that combines the Start menu with the Control Panel of existing Windows. The Charms allows you to quickly configure the device(s) connected to your computer, search for App(s)/file(s), and use the sharing function, etc. Activating the Charms To open the Charms, do the following: •• Touch screen: Swipe inward from the right edge. •• Touchpad/mouse: Place the mouse pointer over the top- or bottom-right corner of the screen.
Using the Charms Chapter 2 Using Windows 36 Changing the Settings Frequently used Windows menus are collected. Icon Name Function Description Wireless Network You can connect to a wireless network. Select a wireless network to connect to. Adjusting the Volume You can adjust the volume or mute the sound. Click the Charms > Settings. Screen Brightness ⦽ ⦽ ENG ⦽ You can adjust the screen brightness. Notice You can set the interval at which an App sends notices.
Using Apps Chapter 2 Using Windows 37 An App refers to an application program (hereafter referred to as an App). In a larger sense, it refers to all the software programs installed on the operating system. Windows provides basic Apps for frequently performed tasks. Starting/Exiting an App Click on an App in the Start screen to activate it. To exit the current app on the touch screen Swipe downward from the top edge of the screen.
Using Apps 3 Click on an App in that list or drag it to the center of the screen. Now, you can check the selected App which is currently running. Right-click over the App in the list and click Close to exit the App. Chapter 2 Using Windows 3 4 Arrange the position of each split screen as appropriate. Move the Screen Split Bar to change the screen split ratio. Weather Screen App Split Bar Store App 1 2 Using split screens 1 2 Select the Apps in the Start screen.
Using Apps Chapter 2 Using Windows Adding/Removing an App to/from the Start Screen 1 Move to the Apps screen. • Touch screen: Swipe upward from the Start screen. • Touchpad/mouse: Click the icon corner of the Start screen. in the bottom-left 2 Tap and hold the app, or right-click it to display the apps list. 3 Select Pin to Start or Unpin from Start .
Using Apps Chapter 2 Using Windows To play the photo or movie Cautions ► To play the Camera-taken photos instantly • Touch screen: Swipe from the left to the right. • Mouse: Click the arrow symbol in the left of the screen. ► On the Start screen, Select Photos > Camera Roll. You can play a continuous roll of captured photos and videos. To edit photos 1 2 Select a photo to edit. Swipe inward from the top edge, or swipe upward from the bottom edge. Alternatively, right-click the photo.
Using Apps Using the Windows Store If you run the App Store in the Start screen, the Apps in the Windows Store are displayed. However, a Microsoft account is required to purchase App(s) in the Windows Store. Continue after registering your Microsoft Account in the Charms. Chapter 2 Using Windows Configuring your Microsoft Account A Microsoft Account allows you to synchronize your settings with other device(s) running Windows online allowing you to share file(s) or settings.
Windows Hot Key Function Chapter 2 Using Windows You can use the following convenient hot keys in Windows. Function Hot Keys Function Description Displaying the Start Screen Windows Key Displaying the Desktop Windows Key + D Switches to Desktop mode. Running the Charms Windows Key + C Activates the Charms. Locking the Screen Windows Key + L Locks the screen. Opening the Ease of Access Center Windows Key + U Opens the Ease of Access Center configuration.
Using a Touch Screen (Touch screen models only) Chapter 2 Using Windows 43 You can use the computer using the touch screen only, without using the keyboard and mouse. The touch screen function is only supported for models which have the function installed at the factory. •• If you are using your computer for a long period of time, it is recommended using a keyboard and mouse. •• Make sure to operate your touch screen using your finger.
Using a Touch Screen (Touch screen models only) Touch Operation or Chapter 2 Using Windows Function Description Swipe inward from the left edge Displays the last run App. Swipe downward from the top edge, or swipe upward from the bottom edge Displays the options for the currently running application. Swipe upward on the Start screen. A tile of all apps installed is displayed. Swipe downward from the top on the All Apps screen The All Apps screen switches to the Start screen.
Using a Touch Screen (Touch screen models only) Touch Operation Touching slightly (Clicking) Touching twice (Double-clicking) Tap and swipe Chapter 2 Using Windows 45 Function Description Slightly press with your finger to select an item. (If you slightly touch a specific menu, option, application icon, etc. on the screen, the corresponding capability is activated.) Slightly press twice with your finger to select an item. Moves the selected target or moves to the next page.
Using a Touch Screen (Touch screen models only) Touch Operation Touching and holding for a while (Right-clicking your mouse) Touching and dragging 2 fingers up/down, left/right (Scrolling) Chapter 2 Using Windows Function Description Provides the same function as right-clicking your mouse button. Displays the additional options which can be set for the selected target or more detailed information. Moves up/down, left/right. Provides the same function as scrolling your mouse.
Using a Touch Screen (Touch screen models only) Calibrating the Screen If you are using the touch screen for the first time or the pointer is not aiming correctly and the accuracy has declined, calibrate your screen. Chapter 2 Using Windows 2 When the Calibration window appears, press the + mark by following the onscreen instructions. 3 The input location of your touch screen is calibrated. The screen calibration process may differ depending on the OS.
Using a Touch Screen (Touch screen models only) Entering Characters You can use the keyboard or Touch Keyboard to enter characters. 3 Chapter 2 Using Windows On the desktop, tap the at the right of the taskbar to display the Touch Keyboard. Entering characters may differ depending on the operating system and is not supported by some operating systems. If you are using your computer for a long period of time, it is recommended using the keyboard.
Using a Touch Screen (Touch screen models only) Chapter 2 Using Windows 49 Touch-enabled mode Entering characters in Handwriting Mode The touch-enabled mode provides the same input environment as the physical keyboard. You can enter characters by writing them in the Handwriting Mode Input Panel on the touch screen. 1 2 1 Tap the Hand-writing mode icon Keyboard. 2 Write characters in the input area of the Handwriting Mode Input Panel on the touch screen.
Using a Touch Screen (Touch screen models only) Note for Using the Touch Screen •• When using the touch screen, make sure to keep your hands clean and dry. In humid environments, dry off your hands and the surface of the touch screen before using the touch screen. •• Do not directly spray LCD display cleaner onto the touch screen. The cleaner may soak through the bottom of the touch screen. When using an LCD display cleaner, spray it onto a cloth to clean your touch screen.
Chapter 3.
Keyboard Chapter 3. Using the computer Shortcut key functions and procedures are discussed in the following sections. •• The keyboard image may differ from the actual keyboard. •• The keyboard may differ depending on your country. The following mainly describes the shortcut keys. Shortcut Keys While pressing and holding the Fn key, press a shorcut keys. Alternatively, press the Fn Lock key as well as a hot key to use the hot key functions more easily.
Keyboard Shortcut Keys Chapter 3. Using the computer Name Settings Screen Brightness Control LCD/External Monitor Touchpad Mute Volume Control Silent Mode Airplane Mode Function The Samsung software control program, the Settings, is launched. Controls the screen brightness. Switches the screen output to the LCD or external monitor when an external monitor (or TV) is connected to the computer. Turns the Touchpad function on or off. When using an external mouse only, you can turn the Touchpad off.
Keyboard Chapter 3. Using the computer Other Function Keys (Optional) •• Performs the right-click mouse function (touchpad). + •• If you press the Fn Lock key, you can use the hot key functions without pressing the Fn key. If the hot keys do not work properly, you have to install the Settings.
Touchpad The touchpad provides the same function as a mouse and the left and right buttons of the touchpad plays the role of the left and right buttons of a mouse. Chapter 3. Using the computer 55 Click Function Place a finger on the touchpad and click on an item once. Alternatively, press the left button once quickly and release it. •• Touch the touchpad with your fingers only. Anything other than your fingers, such as a ball-point pen, will not be recognized by the touchpad.
Touchpad Chapter 3. Using the computer Right Button Function 56 The Gesture Function of the Touchpad (Optional) This corresponds to clicking the right mouse button. Press the right touchpad button once. The corresponding pop-up menu appears. áᔪ the The Touchpad Gesture function may not be provided and version of the function may differ depending on the model. Some usage procedures may differ depending on the version.
Touchpad Chapter 3. Using the computer The Scroll Function Charms Menu Activating Function This function is the same as the scroll area of the Touchpad. If you place your finger on the right edge of the touch pad and drag your finger toward the center, the Charms menu appears. If you place two fingers over the Touchpad and move them up, down, left or right, the screen is scrolled up, down, left or right accordingly.
Touchpad Chapter 3. Using the computer 58 Touchpad On/Off Function Locking with shortcut keys Turning the touchpad off automatically If you want to use the mouse only without using the touchpad, you can turn the touchpad off. When a USB mouse is connected to the computer, the computer can turn the touchpad off automatically. To lock the touchpad function, press the 1 + Alternatively, press the key and then press the turn the touchpad function off. keys.
External-type CD drive (ODD, To be purchased) This computer supports an external USB CD-ROM drive (can be additionally purchased). Check if the interface type of the external CD-ROM drive is a USB type. For detailed specifications, refer to the catalog. Chapter 3. Using the computer Connecting the CD Drive Connect the CD drive to the USB port. •• Do not insert a cracked or scratched CD. Otherwise, the CD may break and damage the optical disk drive when the CD rotates at a high speed.
External-type CD drive (ODD, To be purchased) Inserting and Ejecting a CD 1 Press the Eject button of the CD drive. Status Indicator Emergency Hole Eject Button 2 When the CD tray opens, insert a CD or DVD and push the tray in until it clicks. 3 Push the CD tray inward until it clicks. The CD drive status indicator is turned on. •• A CD drive’s reading and writing speed may differ depending on the condition and type of the media.
Multi Card Slot (Optional) Chapter 3. Using the computer Using the multi-card slot, you can read and write data on various types of memory cards. When you insert a memory card, make sure to insert the memory card in the correct direction. Pushing an incorrectly inserted memory card may damage the card itself or the slot. •• You can use memory cards as a removable disk and conveniently exchange data with digital devices such as a digital camera, etc.
Multi Card Slot (Optional) Chapter 3. Using the computer 62 1 Insert a memory card into the multi-card slot in the correct direction. To remove a memory card 2 The following message appears on the top right. Alternatively, push the tip of the card in and then remove it once it pops up. Click to open the folder and click View Files. If a message appears to notify you of any problem, click the corresponding window > Continue without Scanning. You can perform the following process described in No. 3.
Multi Card Slot (Optional) To format a memory card When using the memory card for the first time, you must format the card before using it. Formatting a card deletes all data saved on the card. If the card includes data, backup the data before formatting it. 1 Click the File Explorer icon of the desktop. 2 Right-click the card drive and click Format. 3 Click Start to the formatting. on the taskbar at the bottom Chapter 3.
Connecting an External Display Device Chapter 3. Using the computer 64 If you connect an external display device such as a monitor, TV, projector, etc., you can view the picture on the wider screen of the external device when you give a presentation or watch a video or movie. Connect an external monitor, TV, or projector that supports the D-SUB interface to display the image on a wider screen. You can connect a D-SUB monitor or HD device using a micro HDMI cable.
Connecting an External Display Device 2 áᔪ Connect the power cord of the connected monitor, TV or projector and turn the power on. Ŗᮁ Change your TV to external device mode when connecting to the TV. ᯲ 3 Select Charms menu > Devices > Projector > Second ᰆ⊹ Screen. Select a3& ִփ desired monitor mode. 3& ִփ PC3& ִփ screen only ᖅᱶ 3& ִփ The contents are only displayed on the PC monitor (current device).
Ŗᮁ Connecting an External Display Device Chapter 3. Using the computer 66 ᯲ 1 Connect the HDMI to micro HDMI cable to the HDMI port of the TV. External Monitor 2 Select Charms menu > Devices > Projector > Second ᰆ⊹ Screen. Select a3& ִփ desired monitor mode. 3& ִփ TV Projector PC3& ִփ screen only ᖅᱶ 3& ִփ The contents are only displayed on the PC monitor (current device).
Adjusting the Volume Chapter 3. Using the computer You can adjust the volume using the keyboard and the volume control program. Adjusting the Volume using the Keyboard + or Using the Sound Recorder The procedures to record sound using the Windows Recorder are described below. Connect a microphone to the microphone jack. + 1 key combination to 2 Right-click over the Volume icon Recording Device. 3 Check if the microphone is set as the default recording device.
Adjusting the Volume Using SoundAlive (Optional) The SoundAlive function enables you to experience more stereophonic sound using stereo speakers. áᔪ •• The software programs provider may vary, depending on your computer model. Ŗᮁ •• In addition, some pictures may differ from actual product depending on the computer model and software version. 1 ᯲ Right-click over the Volume and click Play Device.
Ŗᮁ LCD Brightness Control Chapter 3. Using the computer 69 ᯲ Controlling the Brightness Using the Keyboard Switching the picture mode ᰆ⊹ 1 2 Click the Charms menu > Settings Adjustment icon . > Screen ᖅᱶ Adjust the brightness with the screen brightness control bar. ⦽ You can switch the picture mode to your preferred viewing pleasure, such as optimizing the display for movies or electronic books. 1 2 Click the bottom-left icon on the Start screen. Click Settings > Display > Color tone.
LCD Brightness Control The screen brightness is automatically set to the brightest level when AC power is connected and the brightness is automatically set dimmer when the computer runs on battery power to extend the battery use time. •• Saving battery power consumption Decreases the LCD brightness when the computer is running on battery power to save battery power consumption. •• LCD bad pixels principle of computer Samsung observes the specifications regarding strict quality and reliability of LCD.
Wired Network A wired network is a network environment used for a company network or broadband internet connection at home. Chapter 3. Using the computer 2 Connect the LAN cable to the connected LAN adapter. áᔪ •• You can use wired LAN by using the LAN adapter (Optional). •• This manual is based on the latest Windows. The content or pictures may differ from the actual model, depending on the Windows version.
Wired Network 4 Select Ethenet and click the right button of the touch pad and select Properties. Chapter 3. Using the computer 5 72 Select Internet Protocol Version 4(TCP/IPv4) from the list of Network Components and click Properties. The LAN Device name may differ depending on your computer’s Network Device. •• The Network Component name may differ depending on the Operating System Installed. •• To add a network component, click Install in the screen shown in the figure above.
Wired Network 6 áᔪ Chapter 3. Using the computer 73 Ŗᮁ Configure the IP settings. When using DHCP, select Obtain an IP address automatically. To use a static IP address, select Use the following IP address, and set the IP address manually. Using the WOL (Wake On LAN) function ᯲ is a function that activates the system from Sleep mode when a signal (such as a ping or magic packet command) arrives over the network (wired LAN).
Wired Network Wake On LAN activated by Ping is not supported. When connected to a 100Mbps/1Gbps wired LAN and the computer exits Sleep/hibernation mode, a message appears informing you of a connection to a 10Mbps/100Mbps wired LAN. This happens because when the computer exits standby/hibernate mode, restoring the network takes about 3 seconds. When the network is restored, it operates at 100Mbps/1Gbps.
Wireless Network (Optional) A wireless network (Wireless LAN) environment is a network environment that enables communication between multiple computers at home or a small-size office through wireless LAN devices. Chapter 3. Using the computer 75 •• The screen figures and terms may differ depending on the model. •• Depending on the program version, some functions may not be provided or different functions may be provided.
áᔪ Wireless Network (Optional) Chapter 3. Using the computer 76 Ŗᮁ Connecting to a Wireless LAN ᯲ 2 If there is an AP, you can connect to the Internet via the AP using the Wireless LAN connection method provided by Windows. Click Connect. If a network key is set for the AP, enter the network key and then click OK. ᰆ⊹ 1 For the network key, please ask your network administrator. If you click the Charms menu > Settings > Network Connections icon, a list of available APsᖅᱶappears.
᯲ Mobile broadband (Wireless WAN, Optional) Chapter 3. Using the computer 77 ᰆ⊹ A wireless wide area network (WWAN) is a mobile broadband network that is available in mobile phone service areas. 1 Click Charms > Settings > Network to display available ᖅᱶ mobile broadband networks as shown below. •• The descriptions below are for computer models with mobile broadband devices. A mobile broadband device is optional.
Using the TPM Security Device (Optional) A TPM (Trusted Platform Module) security device is a security solution that protects your personal information by saving the user authentication data on the TPM chip installed on the computer. To use the TPM security device, you have to initialize the TPM chip in the BIOS Setup, initialize the TPM program, and then register the user. •• This function is only supported for models with TPM (security chip). Chapter 3.
Using the TPM Security Device (Optional) Initializing the TPM chip 2 Chapter 3. Using the computer If the BIOS screen appears, select the Security > TPM Configuration item and press Enter. When you use the TPM function for the first time or you want to register the user again, you have to initialize the TPM chip. TPM Device Disabled Enabled •• Initializing the TPM chip erases all authentication information saved on the TPM chip. Any decision to initialize must be taken carefully.
Using the TPM Security Device (Optional) 5 When the system reboots, press the corresponding key(s) by following the onscreen instructions. 6 When the computer restarts automatically and the Samsung logo screen appears, press the F2 key repeatedly. 7 Select the Security > TPM Configuration > Change TPM Status item and set the item to Enable and Activate. TPM Device Enabled TPM State Clear Security Chip State Enabled & Activate Clear Chapter 3.
Using the TPM Security Device (Optional) Registering the TPM program 1 On the Start screen, click the bottom-left icon , and then click Infineon Security Platform Solution > Security Platform Managment > User Settings. (Run as administrator) Alternatively, double-click the icon on the Taskbar and run initialization with administrator authority. 2 The security authentication settings begin with the Initialization Wizard. When the Initialization Wizard appears, click Next.
Using the TPM Security Device (Optional) Using the TPM program 2 Chapter 3. Using the computer If the Confirm Attribute Changes window appears, select the range to apply the encryption to and click OK. (This dialog box only appears when the folder is encrypted.) For more information about using the TPM program, refer to the online help for the program. Encrypting a file (folder) This function enables encrypting files and folders. You can safely protect documents through the Encrypt File System (EFS).
Using the TPM Security Device (Optional) 4 You will be able to confirm that the color of the folder (file) name in the encrypted folder has been changed to green. Chapter 3. Using the computer 83 Opening an encrypted folder (file) 1 2 3 Double-click an encrypted folder (file). If the user authentication window appears, enter the basic user password you entered when registering the user and click OK. The folder (file) opens.
Using the TPM Security Device (Optional) Chapter 3. Using the computer Using the virtual drive (Personal Secure Drive: PSD) When the virtual drive (PSD) is not loaded The virtual drive (PSD) is a virtual space to save and manage confidential data. In the created virtual drive (PSD), you can create files and folders as with a normal drive (e.g. drive C:) and you can use confidential data saved on another drive by copying the data to the virtual drive (PSD).
Using the TPM Security Device (Optional) When you have to register again (to erase the authentication information on the TPM chip) To register a user again, you need to delete the existing authentication information saved on the TPM chip and then clear the TPM chip. If a virtual drive has been created, you have to delete the virtual drive before deleting the existing authentication information saved on the TPM chip. Register the user in the following order.
Using the TPM Security Device (Optional) Deleting the existing authentication information saved on the TPM chip. 1 On the desktop, select the Charms menu > Settings > Control Panel > Programs > Uninstall a program > Infineon TPM Professional Package. Then click Uninstall. 2 If the message window appears, click Yes to remove the program. 3 If the Infineon Security Platform message appears, click No. 4 Click the File Explorer of the desktop.
Using the Multimedia App (Optional) S PhotoStudio and S Player+ enables you to take photos and make videos and edit them to your preference. S PhotoStudio S Player+ Edit photos that you took or selected to your preference. Play music or video clips stored on the computer. Chapter 3. Using the computer 87 •• Depending on the version of the program, some functions may not be provided or different functions may be provided. •• Depending on the model, the application may not be provided.
Using the Multimedia App (Optional) Chapter 3. Using the computer Using the PhotoStudio app 1 2 3 4 On the Start screen, select S PhotoStudio. When done, save the image as a different name. Select a photo to edit. Select an editing mode from the lower-right bar. The content of the top-left bar differs depending on the selected editing mode.
Using Apps With a Samsung Smartphone (Optional) Depending on the model, the application may not be provided. Samsung Kies You can use Samsung Kies to sync multimedia files and documents between the computer and mobile devices, or upgrade the firmware of the connected mobile device to the latest version. For more information, refer to the Help section of this application. HomeSync Lite You can use the computer as Cloud storage to save the uploaded files from Samsung mobile devices.
Samsung Software Update SW Update is a software program that searches for Samsung software programs and drivers installed when you purchased the computer and helps you update any drivers or programs. Chapter 3. Using the computer 2 The SW Update program runs. Select the items that you want to update before proceeding with the update process. •• You can check updatable files before performing the update only when you are connected to the internet.
Diagnosing the Computer Status and Troubleshooting The Support Center program, which is Samsung’s computer’s troubleshooting guide, supports diagnosing the system and has a FAQ for frequently occurring problem(s). 2 1 on the Start screen, and click 91 Support Center is activated and starts diagnosing your computer. After the diagnosing process is finished, the System Status menu displays a list of the current problems to be solved as shown.
Using the Security Slot You can secure the computer by connecting a lock and cable to the Security Slot. To use this feature, you have to purchase the lock and cable additionally. To use the lock and cable, refer to the product manual. Tie the lock and cable to a fixed object and install the other end of the cable to the security slot. Chapter 3.
Chapter 4.
BIOS Setup The BIOS Setup enables you to configure your computer hardware according to your needs. •• Use the BIOS setup to define a boot password, change the booting priority, or add a new device. •• Since incorrect settings may cause your system to malfunction or crash, take care when configuring the BIOS. •• The functions of the BIOS setup are subject to change for product function enhancement purposes. •• The BIOS Setup menus and items may differ depending on your computer model. Chapter 4.
BIOS Setup Chapter 4. Settings and Upgrade System BIOS Setup Keys The BIOS Setup Screen The BIOS Setup menus and items may differ depending on your computer model. Setup Menu System Time > System Date > SATA Port 1 SanDisk SSD U100 126GB CPU CPU CPU CPU Intel(R) Core(TM) i5-3317U CPU 1.70 GHz Supported Vender Type Core Speed VT (VT-x) Total Memory 4096 MB BIOS Version MICOM Version E00AAT.017.120804.dg E00AAT.017 Aptio Setup Utility - Copy (C) 2012 American Megatrends, Inc.
Setting a Boot Password If you set a password, you have to enter the password when you turn the computer on or enter the BIOS Setup. By configuring a password, you can restrict system access to authorized users only and protect data and files saved on the computer. Chapter 4. Settings and Upgrade 1 2 Select the Security menu in the BIOS Setup. In the Set Supervisor Password item, press . •• The password setting provides the following 3 sub menus.
Setting a Boot Password Setting a User Password Using the User Password, you can turn the computer on but you cannot change the major settings of the BIOS Setup because you cannot enter the BIOS Setup. This helps prevent unauthorized access to the major settings in the BIOS Setup menu. Before configuring a user password, a supervisor password must have been configured. Deactivating the supervisor password also deactivates the user password.
Setting a Boot Password Deactivating the Password 1 Press on the password to be deactivated. For example, to deactivate a supervisor password in the Set Supervisor Password item, press . 2 In the Enter Current Password item, enter the currently configured password and press . 3 Leave the Enter New Password item field empty, and press . 4 Leave the Confirm New Password field empty, and press . The password is deactivated.
Changing the Boot Priority The computer is configured so that it boots from the HDD with priority, by default. Chapter 4. Settings and Upgrade 4 99 Set the Boot Device Priority > Boot Option #1 item on the right screen to USB device. This section will show you how to change the setting so that the computer boots from a USB device. The screen image and terms may change depending on the model and the device driver version. 1 2 3 Boot Option Priorities Boot Option #1 xxx Connect the USB device.
Battery Please refer to the following instructions when running the computer on battery power without connecting the AC power. This computer is equipped with an internal battery. Precautions •• Users cannot remove or replace the internal battery. •• To remove or replace the battery, use an authorized service center in order to protect the product and users. You will be charged for this service. •• Use only chargers specified in the User Manual.
Battery Measuring the Remaining Battery Charge You can view the battery charge status by completing the following procedures. Confirming the battery charge in the Taskbar Disconnect the AC adapter and move the mouse cursor over the battery icon in the system tray of the Taskbar to confirm the remaining battery charge.
áᔪ áᔪ Battery Chapter 4. Settings and Upgrade 102 Ŗᮁ Ŗᮁ Using the power management program Extending the Battery Usage Time ᯲ ᯲ This program helps you use the battery more efficiently and supports the power mode optimized for the operating environment. Decreasing the LCD Brightness ᰆ⊹ ᰆ⊹ 1 2 Click the Charms menu > Settings Adjustment icon . > Screen ᖅᱶ 1 Alternatively, right-click the power measuring device icon in the notification area of the taskbar and select Power Options.
Battery Using the Battery Calibration Function When charging/discharging the battery repeatedly for a short time only, the battery usage time may be reduced by the difference between the actual battery charge and the remaining charge display. Chapter 4. Settings and Upgrade 3 103 Move to the Boot > Smart Battery Calibration item using the direction keys and press .
Chapter 5.
Recovering/Backing up the Computer (Optional) If a problem occurs with your computer, Recovery (recovery program) allows you to easily restore your computer to the default (factory) settings. Alternatively, you can back up your computer so that you can restore it to your preferred state at any time. Chapter 5. Troubleshooting 105 •• Recovery may not be provided or may be a different version depending on the model. •• Some functions may differ slightly or be excluded depending on the version.
Recovering/Backing up the Computer (Optional) 3 Recovering You can restore the computer settings to the factory default settings if the computer fails to boot up, or if you encounter a serious problem with the computer. 1 Chapter 5. Troubleshooting If the initial menu screen appears, click Recover. Select a recovery point and click Recover. If you set the User Data Maintenance to ON, the computer is restored while maintaining the current user data.
Recovering/Backing up the Computer (Optional) Recovering after a Backup 2 You can recover your computer after you have backed up your computer to a separate drive or external storage device. Chapter 5. Troubleshooting 107 Click Backup in the Recovery Home screen. Select the drive to save and click Backup. You cannot select a DVD drive. Backing up 1 To back up your computer to an external storage device, connect the external storage device and select the relevant drive. Select the drive to save to.
Recovering/Backing up the Computer (Optional) Recovering You can recover your computer using the backup from the above process. 1 2 3 If the backup image is saved to an external storage device, connect the device. Start Recovery and click Recover. Select a Recover Option and click Recover. Select a point to recover. 4 Chapter 5. Troubleshooting 108 The recover is performed based on the screen instructions. You can use your computer after the recover is completed.
Recovering/Backing up the Computer (Optional) Chapter 5. Troubleshooting 109 To copy the external storage disk When you replace a storage device such as the HDD, SSD, etc. (hereafter referred to as a hard disk) built into your computer, you can move your existing data to the new storage device easily and safely. The new storage device must have sufficient capacity to save your existing data. You need to purchase an external hard USB connector separately to connect the hard disk and your computer.
Recovering/Backing up the Computer (Optional) Export Disk Image Function If you frequently recover your computer to the default (factory) settings, you can conveniently recover your computer after exporting the default (factory) status disk image to an external storage device. 1 2 3 Connect the external storage device, and then select a drive to save to. Click Run. Perform the process by following the instructions to completely save the default (factory) status disk image to the external storage device.
Recovering/Backing up the Computer (Optional) Computer Recovery Function in Windows If a problem occurs with your computer, the recovery program allows you to restore your computer to the default settings. For models where the SSD is less than 64GB, use the Windows System Restore function instead of the Recovery program. 1 Click Charms > Settings > Change PC settings > Update and recovery > Recovery. 2 Click the Get started button for Refresh.... or Remove..... Refresh....
Reinstalling Windows (Optional) You can reinstall Windows using the SYSTEM RECOVERY MEDIA for Windows when Windows is no longer working properly. (For models supplied with a SYSTEM RECOVERY MEDIA.) •• A SYSTEM RECOVERY MEDIA may not be supplied depending on your computer model. •• If you cannot start Windows, or if you want to delete all existing data and reinstall Windows, install Windows according to the descriptions in [Reinstalling when Windows does not start]. Chapter 5.
Reinstalling Windows (Optional) 4 The following window appears, select an installation option. If you click Custom, the procedures from Step 5 continue sequentially. If you click Upgrade, the procedures from Step 6 continue sequentially. Chapter 5. Troubleshooting 5 •• Upgrade Select this option to Upgrade Windows while maintaining current files, configurations and programs.
Reinstalling Windows (Optional) Chapter 5. Troubleshooting Reinstalling when Windows does not start When Windows does not start, boot up with the SYSTEM RECOVERY MEDIA and from there you can reinstall Windows. 1 Insert the SYSTEM RECOVERY MEDIA into the DVD drive and restart the computer. 2 If the Press any key to boot from CD or DVD... message appears while booting, press any key on the keyboard. 3 4 5 114 This screen may not be displayed depending on the OS version.
Q&A Chapter 5. Troubleshooting than the actual capacity because some programs occupy a certain area of the HDD outside of Windows. You can look for potential problems that may occur with the system and view the relevant solutions. Also, you may look up any reference(s) required while operating the computer.
Q&A Chapter 5. Troubleshooting • Touchpad/mouse: Windows Related Q1 on the Start screen to 1. Click the bottom-left icon display a tile of all apps installed on the computer. I cannot find the computer's Shutdown button. 2. Right-click over the corresponding App to select in a Pin to Start. A • Touch screen: - Tap Charms > Settings > Power > Shut down. - Tap and hold the Start button to select Shut down or sign out > Shut down.
Q&A Q5 A How can I change the screen settings, environment settings, color, and so on? Click Charms > Settings > Change PC Settings > PC and devices. You can set the OS settings such as the screen design, etc. Chapter 5. Troubleshooting Q7 A Q6 A Active X does not run in Internet Explorer on the Start screen. Since Internet Explorer on the Start screen complies with the HTML5 web standards, it does not support Active X. However, Internet Explorer on the Desktop supports Active X.
Q&A Sound Related Q1 A I cannot hear any sound from the TV after connecting via the HDMI port. 1. Right-click over the taskbar on the Desktop and click Play Device. 2. Change the option to Digital Audio (HDMI), HDMI device, HDMI Output or another option and click Set as Default. Then click OK. Chapter 5. Troubleshooting 118 Others Q1 A You can configure your computer in the same way as existing Windows systems.
Chapter 6.
Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed. Always follow these instructions to help guard against personal injury and damage to your system.
Important Safety Information Chapter 6 Appendix 121 Care During Use The Instruction On Safety Operation of NotePC •• Do not walk on the power cord or allow anything to rest on it. 1. When installing and operating devices please refer to safety requirements in the user manual. •• Do not spill anything on the system. The best way to avoid spills is to not eat or drink near your system. •• Some products have a replaceable CMOS battery on the system board.
Replacement Parts and Accessories Use only replacement parts and accessories recommended by manufacturer. To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord. Do not use this product in areas classified as hazardous. Such areas include patient care areas of medical and dental facilities, oxygen rich environments, or industrial areas.
Replacement Parts and Accessories Connect and Disconnect the AC adapter The socket-outlet shall be installed near the equipment and shall be easily accessible. Do not unplug the power cord by pulling the cable only. Power Cord Requirements The power cord set (wall plug, cable and AC adapter plug) you received with your computer meets the requirements for use in the country where you purchased your equipment.
Regulatory Compliance Statements Wireless Guidance (If fitted with 2.4G band or 5G band) Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4GHz/5GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device. Additional limitations, cautions, and concerns for specific countries are listed in the specific country sections (or country group sections).
Regulatory Compliance Statements • Wireless devices are not user serviceable. Do not modify them in any way. Modification to a wireless device will void the authorization to use it. Please contact manufacturer for service. • Only use drivers approved for the country in which the device will be used. See the manufacturer System Restoration Kit, or contact manufacturer Technical Support for additional information.
Regulatory Compliance Statements Use On Aircraft Caution Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments. Other Wireless Devices Safety Notices for Other Devices in the Wireless Network: Refer to the documentation supplied with wireless Ethernet adapters or other devices in the wireless network.
Regulatory Compliance Statements If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices.
Regulatory Compliance Statements Health and safety information Exposure to Radio Frequency (RF) Signals Certification Information (SAR) Chapter 6 Appendix 128 SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
Regulatory Compliance Statements Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Intentional Emitter per RSS 210 This device complies with RSS 210 of Industry Canada.
Regulatory Compliance Statements Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. To prevent radio interference to licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding.
Regulatory Compliance Statements European Union European Union CE Marking and Compliance Notices Products intended for sale within the European Union are marked with the Conformité Européene (CE) Marking, which indicates compliance with the applicable Directives and European standards and amendments identified below. This equipment also carries the Class 2 identifier. The following information is only applicable to systems labeled .
Regulatory Compliance Statements Chapter 6 Appendix EU R&TTE Compliance Statements Česky [Czech] Samsung tímto prohlašuje, že tento Notebook PC je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede Samsung erklærer herved, at følgende udstyr Notebook PC overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Regulatory Compliance Statements Magyar [Hungarian] Polski [Polish] Alulírott, Samsung nyilatkozom, hogy a Notebook PC megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Niniejszym Samsung oświadcza, Ŝe Notebook PC jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Samsung declara que este Notebook PC está Português conforme com os requisitos essenciais e outras [Portuguese] disposições da Directiva 1999/5/CE.
Regulatory Compliance Statements To view the EU Declaration of Conformity for this product (in English only), go to: http://www.samsung.com/uk/support/main/ supportMain.do or http://www.samsung.com/uk/support then search the model number of the product. If the Declaration of Conformity for the model you are interested in is not available on our web-site, please contact your distributor or below address. doc.eu@samsung.com Manufacturer Information Samsung Electronics Co., Ltd.
Regulatory Compliance Statements The European variant is intended for use throughout the European Economic Area. However, authorization for use is further restricted in particular countries or regions within countries, as follows: General European standards dictate maximum radiated transmit power of 100 mW effective isotropic radiated power (EIRP) and the frequency range 2400 – 2483.5 MHz. The low band 5.15 - 5.35 GHz is for indoor use only.
WEEE Symbol Information Correct disposal of this product (Waste Electrical & Electronic Equipment) Chapter 6 Appendix 136 Correct disposal of batteries in this product Pb (Applicable in countries with separate collection systems) (Applicable in countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
Samsung Packaging Take-Back Program In partnering with select recyclers, Samsung offers packaging take-back at no cost to you. Simply call the following number for the locations nearest you. CRT Processing, LLC (877) 278-0799 Kathy Severson – Logistics contact Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.
TCO Certified (for corresponding models only) Congratulations! Félicitations ! This product is TCO Certified for Usability and the Environment. The product you have just purchased carries the TCO Certified label. This means that your computer is designed, manufactured and tested according to some of the strictest performance and environmental criteria in the world.
Product Specifications Chapter 6 Appendix 139 The system specifications may differ depending on the derived models. For detailed system specifications, refer to the product catalogue.
Product Specifications Registered Trademarks Chapter 6 Appendix ENERGY STAR® Partner As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Samsung is a registered trademark of Samsung Co., Ltd. Intel, Core are registered trademarks of the Intel Corporation. Microsoft, MS-DOS, and Windows are registered trademarks of the Microsoft Corporation.
Glossary Chapter 6 Appendix 141 The Glossary lists the terminologies used in this user manual. For terminologies other than these, look in Windows Help. Backup DHCP (Dynamic Host Configuration Protocol) A way to save the current data to restore it later if necessary. A backup is a way to restore computer data when the data or computer is damaged. This refers to automatically allocating IP addresses to the users on the network by the network administrators.
Glossary Chapter 6 Appendix 142 DVD (Digital Versatile Disk) Icon DVD was developed to replace CD (compact disk). Although the shape and size of the disc are the same as that of a CD, the capacity of a DVD is at least 4.7GB while the capacity of a CD is 600MB. DVD video is digital unlike VHS (analog) video and supports MPEG2 compression and digital audio. To play a DVD, a DVD drive is required. This refers to a small image that represents a file that users can use.
Glossary Chapter 6 Appendix 143 Network Protocol A group of computers and devices, such as printers and scanners, connected by a communications link. A network can be either small or large and can be connected permanently through cables or temporarily through telephone lines or wireless links. The biggest network is the Internet, a worldwide network. A protocol is a set of rules used by computers to communicate with each other across a network.
Glossary Chapter 6 Appendix Share USB (Universal Serial Bus) This refers to setting a resource of a computer such as a folder or printer so that other users can also use it. This refers to a serial interface standard developed to replace the conventional interface standards such as Serial and PS/2. Shared Folder A folder that can be used by other users on the network. Sleep Mode A power mode that enables computers to save power consumption when they are not being used.
