.1 Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice.
Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed. Always follow these instructions to help guard against personal injury and damage to your system.
Care During Use • Do not walk on the power cord or allow anything to rest on it. • Do not spill anything on the system. The best way to avoid spills is to not eat or drink near your system. • Some products have a replaceable CMOS battery on the system board. There is • • a danger of explosion if the CMOS battery is replaced incorrectly. Replace the battery with the same or equivalent type recommended by the manufacturer. Dispose of batteries according to the manufacturer’s instructions.
Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact an authorized service location.
Regulatory Compliance Statements Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device. Additional limitations, cautions, and concerns for specific countries are listed in the specific country sections (or country group sections).
In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated. When in environments where you are uncertain of the sanction to use wireless devices, ask the applicable authority for authorization prior to use or turning on the wireless device.
United States of America Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Written by: Daryl L. Osden This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on. The power output of the wireless device (or devices), which may be embedded in your notebook, is well below the RF exposure limits as set by the FCC.
If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par Industrie Canada.
Telecommunications per DOC notice (for products fitted with an IC-compliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users’ satisfaction.
European Union The following information is only applicable to systems labeled with the CE mark .
European States qualified under wireless approvals: EU Austria, Belgium, Denmark, Finland, France (with frequency restrictions), Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden and the United Kingdom. Accept EU Iceland, Liechtenstein, Norway and Switzerland European States with restrictions on use: EU In France, the frequency range is restricted to 2446.5-2483.5 MHz for devices above 10 mW transmitting power such as wireless LAN.
Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows® XP operating system. Whether you are new to using a portable computer or are an experienced user, this user’s manual can help you get the most from your computer. Manual Documentation Conventions Information Icons Three icons and their associated messages appear in this manual. The information icons are placed before the step/information they apply to: Warning: Indicates the possibility of personal injury.
CD-ROM Device Naming Convention In many installation programs you will have to get a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD. For instance, if you have one HDD with two partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.
Getting Started Introducing Your Computer The next section will explain the location of all of the buttons, status indicators and equipment needed to operate your notebook computer.
Right Side Earphone Jack Microphone Jack CD Drive (option, p21) USB Port Left Side 1394 Port Fan Vent Modem Port (p31) LAN Port (p32) Monitor Port USB Port PCMCIA Slot (p29) Back Side TV-Out Port (S-VHS) S/PDIF Port (p26) 4 Users Manual DC Jack Battery (p66) Security Lock Port (p78)
Bottom Battery Latches Mini-PCI Compartment* HDD Compartment (p72) Memory Compartment (p73) * Wireless communication module(option, p35) is installed in the mini PCI compartment.
Turning the Computer On and Off To turn on the computer 1. Insert the battery and connect the AC adapter according to the Installation Guide. 2. Slide the LCD latch to the right and open the LCD panel. 3. Press the power button. Power Button LCD Latch Power LED To turn off the computer 1. Click the start button ( 2. Click Turn Off Computer. 6 Users Manual ) on the taskbar.
3. Click Turn Off. If the computer is not turned off properly due to a system error, press ++. When [Windows Task Manager] dialogs appears, click Shut Down > Turn Off to turn off the computer. Your unsaved work may be damaged. If ++ keys do not operate either, press the power button for more than 4 seconds to turn off the computer. Your unsaved work may be damaged. When you turn on the computer next time, it will perform a disk checking process.
Using the Keyboard Your computer has an 87/88-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function & Special Purpose Keys Function Key Windows Key Embedded Numeric Keypad Application Key Cursor/Screen Control Keys Although the layout of the keys on your computer’s keyboard is different from that on a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you use it.
To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and the surface around the keys. Do not allow liquid to drip into the keyboard or you may damage the keyboard. Using the Numeric Keypad Your keyboard includes a numeric keypad, which is a group of keys that you can set to type numbers and mathematical symbols, such as the plus sign. A number or symbol on the left corner of each keypad key shows its numeric function.
Using Special Function Keys The function key activates special functions when it is pressed in combination with another keys. Table 2 shows the special key combinations. Table 2. Description of Special Function Key Combinations Key Combinations Key Name Key Function Esc Rest Rest Puts the computer into Suspend mode. To resume normal operation from rest, press the power button.
Using the Touchpad On Windows, you always see a small graphical image on the screen that indicates the location where you can take the next action. This image is called a pointer, and is usually displayed in arrow shape ( ) or ‘I’ shape ( ). Touchpad Touchpad Buttons Scroll Wheel The touchpad on your computer allows you to move the pointer on the LCD screen, just like a mouse that is used with a desktop computer.
You can use various actions with your touchpad as described below. d Action Function Process Move Move the pointer Place your finger on the touchpad and slide your finger to a destination. Click Select an object, open a menu, or execute a button Place the pointer over an object, then press left touchpad button once. Or, place the pointer over an object, then tap the touchpad once with your finger.
Action Function Process Scroll Display upper/lower/left/right part of the content within a window Place your finger on the scroll wheel, and roll the wheel up or down. (Applicable to only some programs) Or, place your finger on the right edge or bottom edge of the touchpad and move vertically or horizontally. Make sure to use your finger to move the pointer with the touchpad. Do not use any sharpened tool because it may damage your touchpad.
Hot Keys You may program the four keys to the left of the power button to start any program you have installed on your computer. The default settings for these keys are: Icon Name Function Internet Key Launches Internet Explorer. E-Mail Key Launches Outlook Express. User Key Executes user-defined action. WLAN/Bluetooth On/Off Key Turns WLAN/bluetooth on and off. (If you do not have WLAN/Bluetooth module installed, an additional User Key is provided instead.
To reprogram a hot key 1. Double-click Sens Keyboard icon ( ) on the taskbar. 2. Select a key and click Browse to locate the program you wish to assign to the key. 3. Click on your program choice to select it. Click Open. 4. Click OK.
Reading the Status Indicators Status indicators show the status of computer functions. System Top LED Name Function Num Lock Changes a portion of the keyboard to a numeric keypad. See ”Using the Numeric Keypad” on page 9. Caps Lock Changes all alphabet letter input into capital letters. No changes occur to numeric and special keys. Scroll Lock Scroll lock in certain software. HDD Access Blinking Green - HDD is being accessed.
Introducing Windows Understanding the Desktop The desktop is the working area on the computer. It consists of the large workspace and a taskbar at the bottom. Shortcut Icons Start Menu Recycle Bin Language Bar Start Button Taskbar System Tray withClock Start Button Opens the Start menu. Taskbar Displays programs that are currently running. Frequently used icons can be placed here. Recycle Bin Deleted files or folders end up here. Language Bar Switches text input language.
Understanding the Start Menu The Start menu includes everything that is required to start Windows. From the Start menu it is possible to run a program, open a file, assign system users with Control Panel, receive support by clicking Help and Support, and search desired items from computer of Internet by clicking Search.
Understanding a Window A window is the basic component in working with the computer. The My Computer window, which is a window for the computer's hard drive, will be used as an example here to show the basic composition of a window. Click Start > My Computer. Folder Icon Title Bar Menu Bar Close Button Maximize Button Minimize Button Quick Task Window Folders Files Double-click Shared Documents or Local Disk. You can see files and folders.
Help and Support Center Help and Support Center provides references and troubleshooting information regarding computer use. Click Start > Help and Support. Windows XP Tour You can tour elementary functions provided by Windows XP. Click Start > Tour Windows XP. Or click Start > All Programs > Accessories > Tour Windows XP. Click on the topics to find out about important functions of Windows XP.
Using the Computer Using the CD Drive You have one of following drives installed on your computer. CD-ROM drive Reads a CD. CD-RW drive Reads and writes a CD. DVD-ROM drive Reads a CD/DVD. CD-RW/DVD-ROM Combo drive Reads a CD/DVD and writes a CD. To insert a CD 1. Press the eject button on right side of the CD drive. 2. When the tray slides out, place a CD onto the tray with the label facing up, and push the CD down until it clicks. Emergency Eject Hole Eject Button CD Access LED 3.
If you remove the CD when the CD access LED is on, the disk and the data in it may be damaged. Emergency Eject Hole To eject a CD when the CD drive is not working or the computer is turned off, unfold a paper clip, and insert the unfolded end of the clip into the emergency eject hole and press until the CD tray opens. To clean a CD or DVD title Clean the disc with a soft clean cloth by wiping from the center outwards.
Windows Media Player tour For more information about using the Windows Media Player, run the Windows Media Player and click Help > Help Topics > Windows Media Player tour. To play a video CD If a video CD does not run automatically, follow these steps. 1. Insert a video CD into the CD drive. 2. When the CD drive window appears, double-click the MPEGAV folder. 3. Double-click the .dat file. 4. When the [Caution] dialog appears, click Open With. 5. Select “Select the program from a list” and click OK. 6.
To write data on a CD (Option) If your computer has writable CD drive, you can copy data to a blank CD or create an audio CD. Additional CD writing program is supplied in an additional CD. For information about use, refer to the supplied manual. You cannot write on a CD that already has data in it. 1. Insert a blank CD into the CD drive. 2. On the [CD Drive] dialog, select Open Writable CD Folder and click OK. The CD drive window appears. 3. Click Start > My Computer. 4.
5. Click Write these files to CD in the CD drive window. 6. When the CD Writing Wizard appears, enter the CD label, and click Next. The data begins copying. 7. When copying is completed, a message ‘completed’ appears and the CD drive window opens automatically. For more information on writing CDs Click Start > Help and Support. Type “CD copy” in the search field, and click the Search icon ( ). To create an audio CD Run the Windows Media Player program, click the Help > Help Topics.
Enjoying Home Theater (S/PDIF Port) Your computer supports 5.1 channel output, which is a basic function for home theater systems, and DVD drives. It provides 3D surrounding sound and vivid screen. What is a home theater system? Home theater system usually consists of a TV, DVD, 5.1 channel speaker, and digital amp and provides a high-resolution screen (MPEG2) and 3D surrounding sound (Dolby 5.1 or DTS).
Step 1. Connect digital amp, speakers, and TV to the computer 1. Connect a digital amp to the S/PDIF port of your computer. 2. Connect speakers to the digital amp. TV Digital Amplifier Sub Woofer Front Right Speaker Front Left Speaker Computer Center Speaker Surround Left Speaker Surround Right Speaker To watch through a TV Connect the TV and change the setting in the Display Properties to TV. See “Using External Display Devices” on page 60. Step 2.
Step 3. Enable S/PDIF on the DVD program To use 5.1 channel speakers, you need to install the Power DVD program from the DVD Installation CD provided with your computer, then change the settings as following procedure. 1. Run Power DVD program and click the Settings icon ( ). 2. On the Audio tab, set the Audio Output setting to “Use SPDIF” and click OK. Now, you can enjoy home theater using DVD titles. To control volume for your 5.1 channel speaker, use the control on the digital amp.
Using the PCMCIA Card Slot Various different functions can be added by inserting PCMCIA cards into the system. This system supports 16/32 bit, type I or II PCMCIA card types. The PCMCIA card slot does not support a ZV card or a PCMCIA III card. To insert a PCMCIA card Before using the PCMCIA slot, remove the slot protector. Push the eject button of the PCMCIA card slot once to pop it out. Push the button again to eject the slot protector. 1.
Using the Memory Stick Slot In recent, Memory Stick is popular as a removable storage device like floppy diskette. It is widely used for many digital products like digital camera, PDA, etc. Users can easily install a memory stick to save and remove data in it. Memory stick slot is optional when purchasing a computer. First decide the necessary capacity of storage for actual usage and then purchase separately the right amount of memory stick.
Connecting to the Internet Connecting with a Modem Before Start: • Prepare a telephone line that is not digital. • Contact an internet service provider (ISP) for instructions on how to connect to and disconnect from the Internet, and fees. 1. Connect a telephone line to the computer’s modem port. 2. Connect to the Internet according to the instructions provided by your ISP. If the Internet connection is not disconnected properly, additional telephone charges may be imposed.
Connecting Through a Wired LAN 1. Connect a LAN cable to the computer’s LAN port. 2. Click Start > Control Panel. 3. Click Network and Internet Connections in the [Control Panel] window. 4. Click Network Connections in the [Network and Internet Connections] window. 5. Right-click the Local Area Connection icon and click Properties.
6. On the General tab, select “Internet Protocol(TCP/IP)” and click Properties. 7. To use DHCP: On the General tab, select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click OK. To use a static IP: On the General tab, select “Use the following IP address” and fill in the IP address, Subnet mask, Default gateway, Preferred DNS server, and Alternative DNS server fields. Click OK.
Wake On LAN Function is a function that activates the system in rest mode when a signal (such as ping or magic packet commands) arrives from network(wired LAN). To use function: 1. Click Start > My Computer > My Network Places > View network connections. 2. Click the right button on the touchpad over Local Area Connection, and select Properties. 3. Click Configure, and select Power Management tab. Select 'Allow this device to bring the computer out of standby', then click OK.
Connecting Through a Wireless LAN (Option) A wireless network (Wireless LAN) environment is a network environment that enables communication between multiple computers at home or a small-size office through wireless LAN devices. Using the wireless network connections between the systems, you can use normal network functions such as sharing of files, folders and printers.
networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet. For details, see “Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 37. Connecting to an Access Point (AP) This section describes how to connect to an AP. You can use the network when you are connected to an AP. In this section, the configuration procedures are described for Windows XP installed computers.
If the network key is not configured for the desired AP, select 'Allow me to connect to the selected wireless network, even though it is not secure’. Now you are connected to the AP, and you can access the network. Checking the connection status Move the mouse pointer over the Wireless Network Connection ( the taskbar, and the connection status is displayed.
Step 1. Setting up a computer-to-computer network 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks. ) icon on the taskbar, and 2. Click Advanced. 3. On the Wireless Network tab, click Advanced. 4. Clear 'Automatically connect to non-default network' check box, if it is selected. Select 'Computer-to-computer (ad hoc) networks only', and click Close. 5. In the Wireless Networks tab, click Add.
6. Enter the network name (e.g. samsung), and unselect 'The key is provided for me automatically'. Enter the encryption key in the Network key field, and click OK. To prevent a network connection from an unauthorized user, it would be better to configure a network key (encryption key). A network key consists of 5 or 13 alphanumeric characters (e.g. magic), or of 10 or 26 hexadecimal numbers (a hexadecimal number is represented by numbers '0' to '9' or letters 'a' to 'f').
7. Check that the configured network name (e.g. samsung) is in the ’Preferred networks’ item, and click OK. Now your wireless network setup has been completed. Step 2. Connecting to the configured computer 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks. ) icon on the taskbar, and 2. Select the wireless network name (e.g.
If the network key is not configured in ”Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 37, select 'Allow me to connect to the selected wireless network, even though it is not secure'. The two computers are connected and are able to communicate with each other. When the computers are connected, the 'Wireless Network Connection' message is displayed for a short time over the Wireless Network Connection icon of the two computers.
Using Wireless Networks in Other Operating Systems In a operating system other than Windows XP, you have to install additional wireless LAN configuration program, and configure wireless network settings. To use wireless network connection, complete the following procedures. • Step1. Install the wireless LAN configuration program (PROSet). • Step2. Configure wireless network settings through the wireless LAN configuration program. Step 1.
To connect to an Access Point: To connect to an access point or existing computer-to-computer (Ad Hoc) network, refer to the following procedures. (To create a new computer-to-computer network, refer to the following "To create computer-to-computer (Ad Hoc) network" section.) 1. Click Scan in the Networks tab. 2. Select the name of desired access point or computer-to-computer network to connect from the searched available networks list, and click Connect.
- Data encryption (WEP): IEEE 802.11 WEP (Wired Equivalent Privacy) standard has two security levels of 64-bit key (40-bit key for some cases) and 128-bit key. - Key index: Select the current encryption key index used by the access point out of 1 to 4. - To use pass phrase: Click Use pass phrase to activate, and enter 5 (for 64bit) or 13 (for 128-bit) alphanumeric characters (represented by 0-9, a-z, or AZ).
3. Configure password setting to be used for computer-to-computer network connection in the Security Settings window. To connect to an access point, enter the network authentication, data encryption (WEP), key index, and password configured in the access point. It is recommended to configure data encryption for security purposes when creating a computer-to-computer network connection profile. For more information on security settings refer to the security settings in Connecting to AP or Help.
Using Network Services While the computer is connected to the network, you can use network services to share files, folders, and printers. Using computer-to-computer wireless networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet. Network services are provided for the computers that are connected to the network through wired or wireless network connections.
Step 1. Configuring Sharing 1. Right-click the target file or folder to share in My Computer, and select Sharing and Security. 2. Click 'IF you understand the security risks but want to share files without running the wizard, click here'. It has the same security effect as that of the 'Network Setup Wizard'. This screen does not appear if Internet Sharing Network Wizard has been installed in the computer-to-computer wireless network environment. 3. Select 'Just enable file sharing', and click OK. 4.
Step 2. Using Shared Files or Folders This section describes how to access shared files or folders if your computer is a member of the same workgroup. 1. Click Start > My Computer. Under Other Places, click My Network Places in your computer. 2. Click 'View workgroup computers', and click the desired computer to access the shared file. If your computer is a member of another workgroup: 1. Click Other Places > Microsoft Windows Network. 2. Click the desired workgroup. 3.
Step 1. Configuring Printer Sharing 1. From the computer connected to the printer, click Start > Printers and Faxes. 2. Right-click the printer you want to share, and click Sharing. 3. Select 'Share this printer', enter a share name for the shared printer, and click OK. 4. In the Printers and Faxes window, you will find the printer icon has been changed to another icon on a hand. Step 2. Adding and Using a Shared Printer. 1.
5. Select 'Browse for a printer', and click Next. 6. Select the workgroup or computer, select the desired printer, and click Next. If you cannot find the desired printer, try again after a while. 7. Read the warning about a shared printer, and click Yes to install the shared printer. 8. Select Yes for 'Do you want to use this printer as a default printer?', and click Next. 9. Click Finish. 10.
Sharing an Internet Connection Using computer-to-computer (peer-to-peer) network connections, you can access the Internet through a computer connected to the Internet even if your computer is not directly connected to the Internet. To share an Internet connection, the computers should be connected to a computer-to-computer (peer-to-peer) wireless network. For details, see “Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 37.
If the computer is connected to the Internet through a wired LAN, select 'Local Area Connection'. 3. On the Advanced tab, select 'Allow other network users to connect through this computer's Internet connection', and click OK. Step 2. Checking the Shared Internet Connection. When the Internet connection sharing configuration has been completed, the network icon in the Network Connections window is displayed as follows: Click Start > Control Panel > Network and Internet Connections > Network Connections.
Customizing Your Computer Using System Setup The System Setup (BIOS) program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in battery-maintained CMOS memory that saves the information even when the computer’s power is turned off. When your computer is turned back on, it is configured with the values found in this memory. Run System Setup if you get a message prompting you to run the program.
Starting System Setup To start System Setup, turn on your computer and then press and hold until the System Setup screen appears. Table 3. System Setup Menus Menu Function Main Changes the basic system. Advanced Configures advanced features on your computer. Security Enables security features, including passwords. Boot Specifies the order of boot devices and configures boot features. Exit Specifies how to exit System Setup.
Changing Booting Priority The Boot menu in System Setup enables you to select the booting device and to set booting options. Boot Device Priority field enables: You to select the order in which the computer attempts to boot from different devices. The field has four (4) options: CD-ROM Drive, Removable Devices, Hard Drive and MBA UNDI (Bus2 Slot5). To change the booting device priority, choose the device positions by completing the following: 1. At startup, press to open System Setup. 2.
Configuring the Password Setting the Supervisor Password By configuring a supervisor password, you can restrict system access to authorized users only. 1. Select the Security menu in the System Setup. To enter System Setup, see “Starting System Setup” on page 54. 2. On the Set Supervisor Password item, press . 3. Enter a password, press , re-enter the password for confirmation, and press again. 4.
Activating the Hard Disk Drive Password Activating the hard disk drive password prevents the currently installed hard disk drive from being used in other systems. Before activating the hard disk drive password, the supervisor password must have been configured. On the Set HDD 0 Password item, press , and complete step 3-4 of "Setting the Supervisor Password". Deactivating the Password 1. On the password to delete, press . (e.g. supervisor password) 2.
Video Features and Configuration Configuring Resolution and Color Depth Screen resolution is the number of pixels displayed on the screen. High resolution makes the overall screen area large, although individual items appear small. Color quality is determined by the number of bits used to represent a pixel on the screen. High color quality displays more number of colors on your screen. 1. Select Start > Control Panel > Appearance and Themes > Change the screen resolution. 2.
Adjusting the Screen Brightness There are 8 levels of LCD screen brightness (1:Dimmest~8:Brightest). You can adjust the screen brightness by pressing + or + on the keyboard, and the changed screen brightness is displayed on the upper left corner of the screen. The changed brightness setting is maintained after restarting the computer. Whenever you change the power source, to the AC adapter or the battery, the screen brightness is changed to the default setting as follows.
Using External Display Devices Using external display devices such as monitor, projector, TV, etc you can view the screen images alternatively or simultaneously. You can extend the screen into two display devices to use larger workspace. Using external display devices would be especially useful when you are giving presentation or watching a movie through your TV. 1. Connect a monitor or a projector to the monitor port of the system.
To switch display devices using shortcut key You can switch display devices easily by pressing + shortcut key. Provided that CRT monitor is connected, the display order will be LCD > CRT > LCD+CRT whenever the + key is pressed. Provided that multiple external display devices are connected, the display order will be LCD > CRT > LCD+CRT > TV > LCD+TV > CRT+TV > LCD+CRT+TV whenever the + key is pressed.
System Management Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance. Your computer runs fastest with the power cord attached, when power management is disabled.
3. Click the Power Schemes tab to display the basic power management options. Power Schemes Tab 4. Select the time that you wish each of the following actions to occur in Battery and AC power mode. • • • • Turn off monitor Turn off hard disks System standby System hibernates Turning off the monitor and HDDs will save a substantial battery power, therefore when in battery only mode select the shortest time practical.
If You Reinstall Windows: You should re-establish hibernate in power options by opening Power Options Properties window and click on the Hibernate tab then click “Enable Hibernation”. Hibernate Tab Frequent Interruptions: If you experience frequent interruptions, you might also consider putting your computer into automatic hibernation after a specified number of minutes using the power management options.
Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Control Panel > Performance and Maintenance. 2. Click icon to display the Power Options Properties window. 3. Click the Advanced tab to display the advanced power management options. Advanced Tab Power & Sleep Button Programming Windows 4.
Using the Battery Your computer uses a smart rechargeable Lithium-ion (Li-ion) battery pack for power when the AC adapter is not attached to an electrical outlet. The smart battery gives a accurate measurement of the current battery capacity which helps extend operating time by enabling effective power management in operating systems that take advantage of the accurate information supplied by the battery.
Safely Using the Battery Follow these guidelines to safely use the battery: • Turn off your computer and unplug it if you accidentally: – Expose the equipment to liquid. – Drop, jar, or damage the computer. • Use only approved battery chargers. • Do not disassemble the battery, heat it above 100°C, or burn it. The battery used in this computer may cause a fire or chemical burn if mistreated. • Your computer's rechargeable battery may be considered hazardous waste.
2. Insert the battery into the battery compartment until the battery latch snaps into place. 3 Left Battery Latch Right Battery Latch 2 3. Slide the left battery latch toward center to lock the battery in place. Removing the Battery Your computer comes with the battery pack inserted in the computer. To remove the battery from the computer: 1. Turn the computer’s power off. 2. Close the LCD panel, and turn the computer over so that the bottom of the unit faces up. 3. Slide the left battery latch outward.
Monitoring the Battery Charge Battery life is affected by factors such as the power-management settings in System Setup, the applications you use, and the brightness settings of the LCD. Under normal usage, the battery charge lasts approximately 2 hours. Battery life estimates are subject to variation. The actual life of your battery may be less than the estimates given in the manual. You can monitor the charge of the battery pack installed in your computer by using the Power Meter or Battery Gauge.
Battery Gauge You may display the battery gauge while you are in any program by pressing . The battery gauge is only displayed for a few seconds. When using this function, the LCD display may not operate properly. Power Source: Indicates that the computer is powered by the AC adapter. Indicates that the computer is powered by the battery. Battery Level: Indicates the approximate amount of the primary battery charge remaining.
Battery Warnings If the battery charge is low (about 10%) you have ~ 5–10 minutes of battery life left. You should: • Save your work and, • Connect the power cord to the computer or turn off the computer and install a fully charged battery. You can adjust the battery alarm features by using the operating systems power management program (Start > Control Panel > Power Options in Windows).
Using the Hard Drive Your computer includes a removable IDE (integrated drive electronics) hard drive. The IDE hard drive can store the data and programs your computer uses. The drive plugs into a connector on the system board. The hard drive that comes with your computer has already been formatted. Do not format the hard drive. Doing so destroys all data contained on the drive.
Memory Modules You can increase system memory by installing optional memory modules. To avoid possible system problems, use only approved memory modules in your computer. Please consult the appropriate sections of this manual, Samsung Technical Support, or the support Web site (www.samsungpc.com) for additional information. Before You Install Memory To prevent personal injury and damage to the equipment, follow the precautions listed here before installing a memory module.
Installing a Memory Module Handle a memory module carefully. Hold them only by the edges. To install a memory module: 1. Turn the computer over so that the bottom faces up. 2. Using a screwdriver, remove the screw that holds the memory-module compartment door in place. 3 Screw 3. Grasp the edge of the door and pull the door off the chassis. Memory Module Precautions: When removing the module, pull on the plastic portion of the connector slots tabs only.
5. Align the connector on the memory module with the connector of the slot. 6. Push the memory module into the slot at a slight angle (~30o) until the connectors are fully engaged. 6 7 7. Push down on the edge of the memory module until the module snaps into place. 8. Align the memory module compartment door with the compartment and push the door down until it snaps into place. 9. Reinstall the screw you removed in step 2.
Using Options You can select these options at purchase: • Wireless communication module (802.11b, bluetooth) • Memory stick slot You can purchse these options separately: • Extra battery pack (3 cell/6 cell) • Battery charger • Ear set The options that are available may change periodically. Contact your reseller for updated information on current and new options.
Tips for Using Your Computer The following information helps you avoid potential problems as you use your computer: Do not try to disassemble your computer. Opening the system chassis voids your warranty. Only an authorised manufacturer service center can replace or add any parts inside the chassis. • Follow all the instructions and cautions in your computer user documentation. • The LCD has a polarized surface and can be damaged easily. To prevent damage, avoid touching the screen.
Travelling with Your Computer Air Travel If you are travelling by air, follow these tips: • Take the computer with you as carry-on luggage. Do not check the computer with your baggage. • Allow the computer and disks to go through the X-ray security devices. Do not hand-carry disks through the walk-through metal detectors, which can cause loss of data. • Make sure that the battery is charged or the power cord is easily accessible. You may be required to turn on the computer for airport security personnel.
Handling Spills Do not spill anything on your computer. The best way to avoid spills is to avoid eating and drinking around your computer. If you do spill something on your computer, turn off your computer, unplug it immediately, and do the following: • If you spill liquid on the keyboard, drain as much of the liquid from the keyboard as possible. Be careful not to let the liquid drip onto the LCD panel. Allow the system to dry for several days before trying to use it.
Troubleshooting Complete the following in the order presented until your system is functioning properly. If all of the steps below fail then contact your local reseller for assistance. Questions and Answers Please see “Questions and Answers” on page 81 for assistance in correcting any computer operational problems. Check the Connections Verify all of the power and peripheral cables are securely plugged into their sockets and that your system and power supply is on.
Questions and Answers This section provides information on possible problems, solutions and other references for system use. Windows Related Q1 The system does not shutdown properly. A When the system does not shutdown normally, press and hold the Power button until the system manually shuts off. If the Power-Saving Mode is configured into the Power button, press and hold for more than 4 seconds to shut the system off.
Display Related Q1 The LCD screen is blank. A Adjust the LCD screen brightness. Use the , keys. Q2 The screen saver disturbs screen viewing during Media Player or video file operation. A Under the Media Player Options, in Player > Enable Screen Saver During Use, uncheck the box and restart the player. Q3 In DOS mode, changing the full screen DOS mode by pressing key displays a broken image for a short period.
Q7 I pressed + keys, then the screen blinks. A This problem may occur when you pressed + keys to convert display devices while there is no external display device connected.Connect an external display device first, then convert display devices. Q8 When I played an audio file (Mid/Mp3/Wave) on Windows Media Player, the screen resolution is changed or the screen is not displayed.
Q11 + keys does not operate. A When you are playing video file such as a video CD, an MPEG file, or a DVD, when no external display is connected, or when you are using the extended desktop mode or full screen DOS mode, you cannot change display devices. Q12 When I played a DVD or a video CD in dual display clone or extended desktop mode, actions such as changing the display setting or adjusting the volume operates slowly.
Q17 When I changed the screen resolution in extended screen mode and restarted the computer, the screen is not displayed properly. A This problem may occur when the display is set to "Restart the computer before applying the new display settings". (Start > Control Panel > Appearance and Themes > Display > Settings tab > Advanced > General tab) 1. Click Start > Control Panel > Appearance and Themes > Display > Settings tab > Advanced > General tab.
Modem Related Q1 I cannot hear the modem sound. A1 Check that the telephone line is properly connected to the modem. A2 Check that the modem driver is installed properly. 1. Click Start > Control Panel > Performance and Maintenance > System. 2. Select Hardware tab > Device Manager > Modems in the System Properties window, and check if there is a yellow exclamation mark on the installed modem icon.
- Using an AT command As an initialization command, use the command, ATX3. Otherwise, enter the ATX3 command manually before making a call. It can correct this problem by skipping the dial tone check step. - Configuring the Modem through the Control Panel 1. Click Start > Control Panel > Network and Internet Connections. 2. Under See Also, click Phone and Modem Options. 3. In the Modems tab, select the installed modem, and click Properties. 4.
3. Under See Also, click Phone and Modem Options. 4. In the Modems tab, select the installed modem, and click Properties. 5. In the Power Management tab of the Modem Properties window, select the "This device activates the computer in power saving mode" check box, and click OK. The above setting enables the modem to turn on the system and receive a fax when in power saving mode.
Wireless LAN Related Q1 The Wireless LAN device is operating properly, but I cannot connect to the network. This is due to an incorrect configuration, or a configuration error. Check the following check lists: A1 If you are using a computer-to-computer network (peer-to-peer) connection, check that the name of the configured network is correct. The network name used to connect should be the same in all computers. The network name is case sensitive, if the name contains letters.
Even if the network provides DHCP, the server may not allocate an IP address to the client properly, and the client station cannot connect to the network. A2 Referring to A2 of Q1, check that the network key is correct. Q3 I cannot share an Internet connection. A1 It may require some time to synchronize the computers to share an Internet connection after the Internet connection sharing configuration is completed. If you cannot share Internet connection even after a longer period, restart the computer.
A2 Initialize the device driver. Click Start > Control Panel > Performance and Maintenance > System > Hardware tab > Device Manager > Network adapters, and select the wireless LAN adapter. Right-click the network adaptor and select 'Disable'. Then rightclick over the network adaptor and select 'Enable' after a short wait to check that the device is operating properly.
computer-to-computer (Ad Hoc) network is operating properly. Click Refresh to view the latest search result. Q9 Running Help file while running Profile Wizard in the wireless LAN program (PROSet) makes the PROSet window white. A It will be displayed properly when you finish the profile wizard. It dose not affect the program operation. Q10 I installed the WLAN Configuration Program, but it does not operate properly.
Games and Programs Related Q1 3D game is not executed, or some functions are not working. A Change the graphic setting of the game to '2D' or 'Software Renderer', then execute the program again. Q2 I launched a game right after installing it, and the game is not executed. A This problem may occur when the game is not compatible with Windows XP. Launch the game again, and it will be executed properly. Q3 When I played a game, the screen is displayed in reduced size.
Q7 Running speed of a game is too slow or fast. A Change the setting of Power Schemes to 'Always On'. (Click Start > Control Panel > Performance and Maintenance > Power Options > Power Schemes tab, then configure the Power schemes field to 'Always On'.) Q8 Pressing + keys while running a game may cause abnormal operation of the system. A Do not press + keys while a game is running, because it may cause a system error.
Reinstalling Software If you have reinstalled the Windows operating system, or the system and program do not operate properly, you can re-install the driver and program using the system software CD. The drivers and programs included in the system software CD are listed in the D:\ReadMe.htm file. (Provided that the name of CD-ROM drive is "D".) Running the system software CD Insert the system software CD into the CD-ROM drive. The initial screen appears automatically.
Installing programs 1. In the initial screen, click Install programs. 2. Click Standard installation in the program installation screen (standard installation is recommended). • Standard installation: Installs and recovers programs to the state of shipment. • User installation: You can select the program installation location, and other options for the program installation.
Reinstalling Windows XP If the Windows XP does not operate properly due to an error in the system, or if you have replaced the hard disk drive, you can reinstall Windows XP using the system recovery CD. With the system recovery CD, you can reinstall Windows XP only. To return the system to the state of shipment, reinstall the device drivers and programs with the system software CD after reinstalling Windows XP with the system recovery CD.
3. The description for the standard installation appears. Click Yes. The installation starts, and the system will be restarted after a while. 4. After the system has restarted, the message ’Press any key to boot from CD’ appears. Do not press any key at this time. After a while the partition configuration screen appears. To not change the partition, press . What is partition configuration? Partition configuration is a function that devides the hard disk drive into one or several partitions.
If You Cannot Run Windows If you cannot run Windows, you have to boot the system with the system recovery CD, and reinstall Windows. If you boot the system from the system recovery CD, you can install Windows only with the user installation option. You cannot install with the standard installation option. 1. Insert the system recovery CD into the CD-ROM drive and start the computer. 2. If the following message appears on the screen, press any key from the keyboard. Press any key to boot from CD.....
Specifications System Specification The following is the basic hardware specification for the purchased product. Variations may exist depending on the model type. Item Specification CPU Intel PentiumM 1.3~1.7 GHz Cache memory 1MB Main memory 128/256/512/1024 MB DDR SDRAM, 2 DDR socket Main Chipset Intel 855GM/ICH4M Remarks Maximum 2GB Hard disk drive (HDD) 2.5’’, UltraDMA 100, S.M.A.R.T 9.
Wireless LAN Specification Product Specification Item Physical Specifications Detailed Specifications Dimensions (Width X Height) 59.75 X 44.45 mm operation temperature and humidity Same as system operation Temperature: 0°C ~ 70°C Humidity: less than 85% Power Specification Network Specifications Power Saving Mode 135 mW Receiving Mode 1.0 W Transmission Mode 1.6 W Power 3.3V Compatibility IEEE802.11b standard (DSSS) Mini-PCI Rev.1.
Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country. In France however, use only 4 channels (channel 10, 11, 12, 13) when using wireless networks. • Standard: IEEE 802.
Abbreviations A . . . . . . . . . Amperes AC . . . . . . . . Alternating current ACPI . . . . . . Advanced Configuration and Power management Interface APM . . . . . . Advanced Power Management ATA. . . . . . . AT attachment (refers to the hard-drive interface in an ATcompatible computer) ATAPI. . . . . AT attachment packet interface BBS . . . . . . . Bulletin board system BIOS . . . . . . Basic input/output system C . . . . . . . . . Centigrade CD . . . . . . . . Compact disc CD-ROM . .
ISA . . . . . . . Industry Standard Architecture KB . . . . . . . . Kilobytes kg . . . . . . . . . Kilograms LAN. . . . . . . Local-area network lb.. . . . . . . . . Pounds LBA . . . . . . . Logical block addressing LCD. . . . . . . Liquid-crystal display m . . . . . . . . . Meters mA . . . . . . . . Milliampere mAhr . . . . . . Milliampere hour MB. . . . . . . . Megabyte mm . . . . . . . millimeter MPEG . . . . . Motion Picture Experts Group MPU . . . . . . Microprocessor unit ms . . . . . . . .
Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts). The 32-bit cards can transmit more data at a time than the 16-bit cards, thus increasing their speed. CMOS memory CMOS (complementary metal oxide semiconductor) memory is powered by the CMOS battery.
Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer. Because hard drives in notebook computers are smaller than those in desktop computers, their maximum storage capacity may be less than that of desktop hard drives.
PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed. Pixel A pixel is an individual dot in a graphic displayed on your computer. The pixels are so close together that they look as though they are connected.
Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer. TFT (thin film transistor) LCD A TFT LCD uses a separate transistor circuit to control each pixel. This technology provides the best resolution for an LCD screen. A TFT LCD is also sometimes called an active matrix LCD.
Using Windows 2000 Samsung notebook provides Windows XP or 2000 as operating system depending on the product model. Because the use of Windows XP is similar to Windows 2000, the same User Guide (Online Manual) is used regardless of operating system installed on your notebook. However, since there are some differences in menus, screens, and operations, you need to refer to this Guide if your notebook's operating system is Windows 2000.
Introducing Windows Descriptions presented in ”Introducing Windows” (p 17) are applicable only to Windows XP. For Windows 2000, location of menus, shape of icons and some uses may differ from those of Windows XP. To Playback Audio or Video CD Just insert your audio or video CD into your CD drive. The associated application program will start automatically and playback the audio or video files.