Notice and Safety With Wireless - English V1.1.fm Page i Friday, May 3, 2002 3:21 PM 1.1 Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice.
Notice and Safety With Wireless - English V1.1.fm Page ii Friday, May 3, 2002 3:21 PM Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed. Always follow these instructions to help guard against personal injury and damage to your system.
Notice and Safety With Wireless - English V1.1.fm Page iii Friday, May 3, 2002 3:21 PM Care During Use • Do not walk on the power cord or allow anything to rest on it. • Do not spill anything on the system. The best way to avoid spills is to not eat or drink near your system. • Some products have a replaceable CMOS battery on the system board. There is • • a danger of explosion if the CMOS battery is replaced incorrectly.
Notice and Safety With Wireless - English V1.1.fm Page iv Friday, May 3, 2002 3:21 PM Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact an authorized service location.
Notice and Safety With Wireless - English V1.1.fm Page v Friday, May 3, 2002 3:21 PM Regulatory Compliance Statements Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device.
Notice and Safety With Wireless - English V1.1.fm Page vi Friday, May 3, 2002 3:21 PM In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated.
Notice and Safety With Wireless - English V1.1.fm Page vii Friday, May 3, 2002 3:21 PM United States of America Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Written by: Daryl L.
Notice and Safety With Wireless - English V1.1.fm Page viii Friday, May 3, 2002 3:21 PM The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on.
Notice and Safety With Wireless - English V1.1.fm Page ix Friday, May 3, 2002 3:21 PM If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Notice and Safety With Wireless - English V1.1.fm Page x Friday, May 3, 2002 3:21 PM Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada.
Notice and Safety With Wireless - English V1.1.fm Page xi Friday, May 3, 2002 3:21 PM Telecommunications per DOC notice (for products fitted with an IC-compliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users’ satisfaction.
Notice and Safety With Wireless - English V1.1.fm Page xii Friday, May 3, 2002 3:21 PM European Union The following information is only applicable to systems labeled with the CE mark .
Notice and Safety With Wireless - English V1.1.fm Page xiii Friday, May 3, 2002 3:21 PM European States qualified under wireless approvals: EU Austria, Belgium, Denmark, Finland, France (with frequency restrictions), Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden and the United Kingdom. Accept EU Iceland, Liechtenstein, Norway and Switzerland European States with restrictions on use: EU In France, the frequency range is restricted to 2446.5-2483.
Notice and Safety With Wireless - English V1.1.fm Page xiv Friday, May 3, 2002 3:21 PM Japan VCCI Statement This equipment is in the Class B category (Information Technology Equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment aimed at preventing radio interference in such residential areas.
Notice and Safety With Wireless - English V1.1.fm Page xv Friday, May 3, 2002 3:21 PM Prior to setting up your device: 1. Make sure that there are no other devices in your area using the same frequency band. 2. Change the channel, location, or discontinue device use if you are interfering with any other radio station. 3. Contact manufacturer if you have any problems with this device.
Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows® XP operating system. Whether you are new to using a portable computer or are an experienced user, this user’s manual can help you get the most from your computer. Manual Documentation Conventions Information Icons Three icons and their associated messages appear in this manual. The information icons are placed before the step/information they apply to: Warning: Indicates the possibility of personal injury.
CD-ROM Device Naming Convention In many installation programs you will have to get a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD. For instance, if you have one HDD with two partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.
Introducing Your Computer Your computer is a lightweight portable computer that includes following features to meet your computing needs at home or on the road: - Home Theater System Support (dependant on configuration) - CD-RW/DVD-ROM Combo Drive Factory options (Figures may be different depending on options) - Fingerprint recognition system - Memory Stick - Wireless LAN (802.
Right Side Earphone Jack Microphone Jack CD-RW/DVD-ROM Combo Drive USB Port Left Side 1394 Port Fan Vent Modem Port LAN Port VGA Port USB Port PCMCIA Slot Back Side TV-Out Port (S-VHS) S/PDIF Jack 4 Users Manual DC Jack Battery Security Lock Port
Bottom Battery Latches Mini-PCI Compartment* HDD Compartment Memory Compartment * Wireless communication module(option) is installed in the mini PCI compartment.
Using Your Computer for the First Time This section gives you detailed information on using your computer for the first time. Turning On the Computer To turn on the computer’s power for the first time: 1. Install the battery and connect the AC adapter according to the Installation Guide. 2. Slide the LCD cover latch to the right. 3. Lift up the cover. 4. Press and then release the power button. The power LED is on when the computer’s power is on.
Turning Off Your Computer Prior to shutting down your computer ensure all of your data and current work are saved. The system will ask if you wish to save any unsaved work, saving your work first will speed the shutdown process. To turn off the computer, complete the following steps: 1. Click on the taskbar. If you need to restart your computer after software (re)installation or because it is not responding select the Restart option in step 3 below. 2. Click Shut Down Computer below. 3.
Tips for Using Your Computer The following information helps you avoid potential problems as you use your computer: Do not try to disassemble your computer. Opening the system chassis voids your warranty. Only an authorised manufacturer service center can replace or add any parts inside the chassis. • Follow all the instructions and cautions in your computer user documentation. • The LCD has a polarized surface and can be damaged easily. To prevent damage, avoid touching the screen.
Travelling with Your Computer Air Travel If you are travelling by air, follow these tips: • Take the computer with you as carry-on luggage. Do not check the computer with your baggage. • Allow the computer and disks to go through the X-ray security devices. Do not hand-carry disks through the walk-through metal detectors, which can cause loss of data. • Make sure that the battery is charged or the power cord is easily accessible. You may be required to turn on the computer for airport security personnel.
Handling Spills Do not spill anything on your computer. The best way to avoid spills is to avoid eating and drinking around your computer. If you do spill something on your computer, turn off your computer, unplug it immediately, and do the following: • If you spill liquid on the keyboard, drain as much of the liquid from the keyboard as possible. Be careful not to let the liquid drip onto the LCD panel. Allow the system to dry for several days before trying to use it.
Using the Keyboard Your computer has an 87/88-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function & Special Purpose Keys Function Key Windows Key Embedded Numeric Keypad Application Key Cursor/Screen Control Keys Although the layout of the keys on your computer’s keyboard is different from that on a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you use it.
To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and the surface around the keys. Do not allow liquid to drip into the keyboard or you may damage the keyboard. Using the Numeric Keypad Your keyboard includes a numeric keypad, which is a group of keys that you can set to type numbers and mathematical symbols, such as the plus sign. A number or symbol on the right corner of each keypad key shows its numeric function.
Using Special Function Keys The function key activates special functions when it is pressed in combination with another keys. Table 2 shows the special key combinations. Table 2. Description of Special Function Key Combinations Key Combinations Key Name Key Function Esc Rest Rest Puts the computer into Suspend mode. To resume normal operation from rest, press the power button.
User Defined Buttons (SENS Keyboard) You may program the four buttons to the left of the power button to start any program you have installed on your computer. The default settings for these buttons are: Icon Name Function Internet Button Launches Internet Explorer. E-Mail Button Launches Outlook Express. User Button Executes user-defined action. WLAN/Bluetooth On/Off Button Turns WLAN/bluetooth on and off.
To reprogram the Sens Keyboard, follow the steps below: 1. Double-click displayed. icon on the Windows taskbar, the Key Setting window is 2. Use the Browse button to locate the program you wish to assign to the SENS Keyboard button selected. 3. Click on your program choice to select it. Click Open. 4. Click OK to close window and complete programming the Sens Keyboard.
Using the Touchpad Your computer is equipped with a touchpad, which is an integrated-pointing device that is used to perform standard mouse functions. The touchpad is an advanced and reliable pointing device that works with a touch of your finger. Touchpad Touchpad Buttons Scroll Wheel or Fingerprint Sensor Scroll Wheel Use If the scroll wheel does not function properly, install the scroll wheel driver provided on the Software CD. Press on the touchpad gently. The touchpad responds to light pressure.
d Action Process and Comment Click/Tap Process Depress the touchpad left button and release or position the pointer over the object and quickly tap the touchpad once with your finger. This action is called clicking. Comment This will cause a process to begin or select an object on the screen. Double-click/Tap Process Quickly click the left touchpad button two times or position the pointer over the object and quickly tap the touchpad twice with your finger. This action is called Double-clicking.
Drag (Move) To move a window on the desktop, complete the following: 1. Click the window title bar of the window which you want to drag using the touchpad. 2. Press the left touchpad button and hold it. 3. Drag the window using the touchpad. 2 Drag your finger to move the window. 1 Click the Window Title Bar and Hold. Area or Multiple item selection: The drag function may be used to select an area or multiple items in an area by clicking in one area and then dragging to create a selection window.
Reading the System Status Lights System Top System Status lights show the status of computer functions. LED Name Function Num Lock Changes a portion of the keyboard to a numeric keypad. See ”Using the Numeric Keypad” on page 12. Caps Lock Changes all alphabet letter input into capital letters. No changes occur to numeric and special keys. Scroll Lock Scroll lock in certain software. HDD Access Blinking Green - HDD is being accessed.
Connecting to the Internet This section explains how to connect you to the internet. For details on how to establish the connection contact the Internet Service Provider (ISP) or system administrator (SysAdmin). Using the Modem Install the Modem cable by simply plugging the cable into the modem slot as shown in the figure below. Your notebook computer may have both a modem and a LAN socket, please ensure you plug the modem cable into the correct socket. 1.
Precautions Before Use Country Selection Country Selection: Because you may use your computer in more than one country, please ensure you select the country you are calling from to avoid connection problems. To change the country selection proceed as follows: 1. Click Start > Control Panel > Network and Internet Connections. 2. Click Phone and Modem Options. 3. Click on the connection you wish to edit in the Locations: box. 4. Click Edit in the Dialing Rules Tab. 5.
If you use a simple terminal program (i.e. hyper terminal): Type the “ATX3&W” or “ATX3” command as an initialization command. MODEM Notes: 1. In order to use the V.90 feature, be sure to check if the standards supported by the on-line service provider and the modem are identical. Download speed is limited to 53Kbps. Upload speed is limited to 31.2Kbps. Speeds can vary by line condition. 2. If you use a PBX phone system, you can not connect using the V.90 mode. 3.
Configuring Network Environment Configure the Network Adapter as follows: 1. Click Start > Control Panel > Network and Internet Connections. 2. Click icon (Network Connections). 3. Right-click the icon (Local Area Network) then click Properties button. 4. Select Internet Protocol (TCP/IP) in the “This connection uses the following items:” box. 5. Click Properties. The TCP/IP Properties window opens. Step 7 Step 8 6. Click “Use the following IP address” in the General tab. 7.
Using Both DHCP and Static IP Simultaneously When you are alternatively using networks with either DHCP or static IP addressing, you can use both of the network connections without reconfiguring using alternative settings that enable simultaneous configurations of DHCP and static IP. This function is provided only when your operating system is Windows XP. 1.
Wake On LAN Function is a function that activates the system in rest mode when a signal (such as ping or magic packet commands) arrives from network(wired LAN). To use function: 1. Click Start > My Computer > My Network Places > View network connections. 2. Click the right button on the touchpad over Local Area Connection, and select Properties. 3. Click Configure, and select Power Management tab. Select 'Allow this device to bring the computer out of standby', then click OK.
Configuring the Network Environment Settings for Wireless Network (WLAN) A wireless network (Wireless LAN) environment is a network environment that enables communication between multiple computers at home or a small-size office through wireless LAN devices. Using the wireless network connections between the systems, you can use normal network functions such as sharing of files, folders and printers.
Connecting to an Access Point (AP) This section describes how to connect to an AP. You can use the network when you are connected to an AP. In this section, the configuration procedures are described for Windows XP installed computers. For information on the configuration procedures for other operating systems, see “Using Wireless Networks in Other Operating Systems” on page 33. Please ask your network administrator about detailed configuration information such as the network key (encryption key). 1.
Checking the connection status Move the mouse pointer over the Wireless Network Connection ( the taskbar, and the connection status is displayed. ) icon on Connecting to computer-to-computer networks (peer-to-peer or ad hoc) In computer-to-computer wireless networks, you can wirelessly connect 2 or more computers that have wireless LAN modules. You can connect by completing the following steps: • Step 1. Set up a computer-to-computer network on a computer. • Step 2.
Step 1. Setting up a computer-to-computer network 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks. ) icon on the taskbar, and 2. Click Advanced. 3. On the Wireless Network tab, click Advanced. 4. Clear 'Automatically connect to non-default network' check box, if it is selected. Select 'Computer-to-computer (ad hoc) networks only', and click Close. 5. In the Wireless Networks tab, click Add.
6. Enter the network name (e.g. samsung), and unselect 'The key is provided for me automatically'. Enter the encryption key in the Network key field, and click OK. To prevent a network connection from an unauthorized user, it would be better to configure a network key (encryption key). A network key consists of 5 or 13 alphanumeric characters (e.g. magic), or of 10 or 26 hexadecimal numbers (a hexadecimal number is represented by numbers '0' to '9' or letters 'a' to 'f').
7. Check that the configured network name (e.g. samsung) is in the ’Preferred networks’ item, and click OK. Now your wireless network setup has been completed. Step 2. Connecting to the configured computer 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks. ) icon on the taskbar, and 2. Select the wireless network name (e.g.
If the network key is not configured in ”Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 28, select 'Allow me to connect to the selected wireless network, even though it is not secure'. The two computers are connected and are able to communicate with each other. When the computers are connected, the 'Wireless Network Connection' message is displayed for a short time over the Wireless Network Connection icon of the two computers.
Using Wireless Networks in Other Operating Systems In a operating system other than Windows XP, you have to install additional wireless LAN configuration program, and configure wireless network settings. To use wireless network connection, complete the following procedures. • Step1. Install the wireless LAN configuration program (PROSet). • Step2. Configure wireless network settings through the wireless LAN configuration program. Step 1.
To connect to an Access Point: To connect to an access point or existing computer-to-computer (Ad Hoc) network, refer to the following procedures. (To create a new computer-to-computer network, refer to the following "To create computer-to-computer (Ad Hoc) network" section.) 1. Click Scan in the Networks tab. 2. Select the name of desired access point or computer-to-computer network to connect from the searched available networks list, and click Connect.
- Data encryption (WEP): IEEE 802.11 WEP (Wired Equivalent Privacy) standard has two security levels of 64-bit key (40-bit key for some cases) and 128-bit key. - Key index: Select the current encryption key index used by the access point out of 1 to 4. - To use pass phrase: Click Use pass phrase to activate, and enter 5 (for 64bit) or 13 (for 128-bit) alphanumeric characters (represented by 0-9, a-z, or AZ).
3. Configure password setting to be used for computer-to-computer network connection in the Security Settings window. To connect to an access point, enter the network authentication, data encryption (WEP), key index, and password configured in the access point. It is recommended to configure data encryption for security purposes when creating a computer-to-computer network connection profile. For more information on security settings refer to the security settings in Connecting to AP or Help.
Using Network Services While the computer is connected to the network, you can use network services to share files, folders, and printers. Using computer-to-computer wireless networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet. Network services are provided for the computers that are connected to the network through wired or wireless network connections.
Step 1. Configuring Sharing 1. Right-click the target file or folder to share in My Computer, and select Sharing and Security. 2. Click 'IF you understand the security risks but want to share files without running the wizard, click here'. It has the same security effect as that of the 'Network Setup Wizard'. This screen does not appear if Internet Sharing Network Wizard has been installed in the computer-to-computer wireless network environment. 3. Select 'Just enable file sharing', and click OK. 4.
Step 2. Using Shared Files or Folders This section describes how to access shared files or folders if your computer is a member of the same workgroup. 1. Click Start > My Computer. Under Other Places, click My Network Places in your computer. 2. Click 'View workgroup computers', and click the desired computer to access the shared file. If your computer is a member of another workgroup: 1. Click Other Places > Microsoft Windows Network. 2. Click the desired workgroup. 3.
Step 1. Configuring Printer Sharing 1. From the computer connected to the printer, click Start > Printers and Faxes. 2. Right-click the printer you want to share, and click Sharing. 3. Select 'Share this printer', enter a share name for the shared printer, and click OK. 4. In the Printers and Faxes window, you will find the printer icon has been changed to another icon on a hand. Step 2. Adding and Using a Shared Printer. 1.
5. Select 'Browse for a printer', and click Next. 6. Select the workgroup or computer, select the desired printer, and click Next. If you cannot find the desired printer, try again after a while. 7. Read the warning about a shared printer, and click Yes to install the shared printer. 8. Select Yes for 'Do you want to use this printer as a default printer?', and click Next. 9. Click Finish. 10.
Sharing an Internet Connection Using computer-to-computer (peer-to-peer) network connections, you can access the Internet through a computer connected to the Internet even if your computer is not directly connected to the Internet. To share an Internet connection, the computers should be connected to a computer-to-computer (peer-to-peer) wireless network. For details, see “Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 28.
If the computer is connected to the Internet through a wired LAN, select 'Local Area Connection'. 3. On the Advanced tab, select 'Allow other network users to connect through this computer's Internet connection', and click OK. Step 2. Checking the Shared Internet Connection. When the Internet connection sharing configuration has been completed, the network icon in the Network Connections window is displayed as follows: Click Start > Control Panel > Network and Internet Connections > Network Connections.
Using the Disk Drives Using the CD-RW/DVD-ROM Combo Drive You have to install the CD Writer software provided on a separate CD to write a CD. For more information, read the manual included in the CD. You have to install the DVD software provided on a separate CD to view a DVD title. 1. Press the button on the CD-RW/DVD-ROM Combo drive, and the tray slides out. CD-ROM Drive Warnings: Do not place reflective objects other than the CD/DVD disks in the disk slot because of possible hazardous laser emissions.
3. Push the tray in gently to close the drive tray. Emergency Eject Hole Eject Button CD-ROM LED Install and/or start a CD-based program as you would run a program on a floppy disk. Using the Memory Stick (Factory Option) The Memory Stick is a factory option that will increase your computer storage capacity as well as increase data portability. The Memory Stick may used in many types of equipment such as digital cameras and PDAs for example. Memory Stick and are a trademarks of the Sony Corporation.
1. Slide the Memory stick into the slot until you feel the first latch catch. 2. Then push the Memory stick in until it clicks into place. Using the Memory Stick The Memory Stick is used the same as the FDD drive on your computer but with much larger capacity, currently up to 128MB. Formatting the Memory Stick The Memory Stick may need to be formatted before use, if so insert it into the slot and format it the same as the FDD Drive.
Removing the Memory Stick To remove the Memory Stick proceed as follows: Ensure any operations using the Memory stick have completed before you remove it. Otherwise you will corrupt your data. When you are using Windows 2000, remove a memory stick after at least 20 seconds after finishing a task, such as formatting, copying, or deleting. Removing a memory stick directly after executing a task may cause a problem in Windows 2000. 1. Push the Memory Stick in until it clicks and release. 2.
Working with PC Cards By installing PC Cards, you can add functions to your notebook computer similar to those found on add-in boards for desktop computers. Available PC Cards include: • Input/output, such as modem, network, video capture, and SCSI cards. • Storage, such as hard drive and flash memory cards. Your computer includes the following PC Card support: • One PC-Card slot: You can install Type I or II cards in the slot.
3. Align the card with a slot and insert the card into the slot until it locks in place. Eject Button Windows automatically assigns computer resources (such as communication ports and memory addresses) to a PC Card installed in your computer. To remove a PC Card from your computer: Use the following procedures to remove PC Cards, or you may lose data that is being stored to a card. 1. Click icon on the taskbar. 2. Select the card currently in use, and click the Stop button.
Multi Media Functions/Equipment Media Player The Windows Media player is used to play audio files while the computer is on. You can play audio/video CD files using the Windows Media Player, as well as watching TV, video and listening to the radio through internet. The instructions to play a video CD-ROM are the same as the instructions for the audio CD below. Playing an Audio/Multimedia CD To play a CD follow the instructions below: 1. Insert a compact disc into your CD-ROM drive. 2.
Removing the Audio/Multimedia CD To remove the CD follow the instructions below: 1. Click Start > All Programs > Accessories > Entertainment > Windows Media Player to open the Windows Media Player window, if not already open. 2. Click Stop in the Windows Media Player window or simply close the Windows media player. 3. Press the button on your CD-ROM drive. The drive tray opens and you can remove the CD from the CD-ROM drive. 4.
Setting Up Your Home Theater 1. Connect the digital amplifier to the S/PDIF port of your computer. 2. Connect the speakers to the digital amplifier. TV Sub Woofer Digital Amplifier Front Right Speaker Front Left Speaker Computer Center Speaker Surround Left Speaker Surround Right Speaker If your computer supports a TV-Out port, you can connect and enjoy a large screen. After connecting the TV, you will need to select the TV as the display device using the Windows Display Properties window.
Enabling S/PDIF on the DVD Program When using 5.1 channel speakers, you will need to install the “Power DVD” program on the DVD Installation CD (supplied separately) and then set it up as described below: 1. Run the “Power DVD” program and click the settings button. The configurations window pops up. Settings Button 2. On the Audio tab, change the Audio Output setting to “Use SPDIF” and click OK. 3. You are ready to enjoy your home theater system with your own DVD. To control the sound volume on your 5.
Volume Control The instructions below are for controlling speaker volume when the computer is on. Using the Keyboard Changing the volume with your keyboard. Use to decrease the volume or to increase the volume. Using the Volume Control Icon Double-click icon in the active program tray. The Volume Control window pops up. Use this window to adjust the volume. You can pop up a simple volume slider by a single click icon.
Using the Battery Your computer uses a smart rechargeable Lithium-ion (Li-ion) battery pack for power when the AC adapter is not attached to an electrical outlet. The smart battery gives a accurate measurement of the current battery capacity which helps extend operating time by enabling effective power management in operating systems that take advantage of the accurate information supplied by the battery.
Safely Using the Battery Follow these guidelines to safely use the battery: • Turn off your computer and unplug it if you accidentally: – Expose the equipment to liquid. – Drop, jar, or damage the computer. • Use only approved battery chargers. • Do not disassemble the battery, heat it above 100°C, or burn it. The battery used in this computer may cause a fire or chemical burn if mistreated. • Your computer's rechargeable battery may be considered hazardous waste.
2. Insert the battery into the battery compartment until the battery latch snaps into place. Left Battery Latch 3 Right Battery Latch 2 3. Slide the left battery latch toward center to lock the battery in place. Removing the Battery Your computer comes with the battery pack inserted in the computer. To remove the battery from the computer: 1. Turn the computer’s power off. 2. Close the LCD panel, and turn the computer over so that the bottom of the unit faces up. 3.
Monitoring the Battery Charge Battery life is affected by factors such as the power-management settings in System Setup, the applications you use, and the brightness settings of the LCD. Under normal usage, the battery charge lasts approximately 2 hours. Battery life estimates are subject to variation. The actual life of your battery may be less than the estimates given in the manual. You can monitor the charge of the battery pack installed in your computer by using the Power Meter or Battery Gauge.
Battery Gauge You may display the battery gauge while you are in any program by pressing . The battery gauge is only displayed for a few seconds. When using this function, the LCD display may not operate properly. Power Source: Indicates that the computer is powered by the AC adapter. Indicates that the computer is powered by the battery. Battery Level: Indicates the approximate amount of the primary battery charge remaining.
Battery Warnings If the battery charge is low (about 10%) you have ~ 5–10 minutes of battery life left. You should: • Save your work and, • Connect the power cord to the computer or turn off the computer and install a fully charged battery. You can adjust the battery alarm features by using the operating systems power management program (Start > Control Panel > Power Options in Windows).
Using System Setup The System Setup (BIOS) program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in battery-maintained CMOS memory that saves the information even when the computer’s power is turned off. When your computer is turned back on, it is configured with the values found in this memory. Run System Setup if you get a message prompting you to run the program.
Table 4. System Setup Navigation Keys 62 Users Manual Navigation Key Function Displays the General Help window. Exits the current menu. or Moves the cursor up and down between fields. or Selects different menus. Pressing the key at the Main menu brings you to the Exit menu. Scrolls backwards through the options for the highlighted field. Scrolls forward through the options for the highlighted field.
Changing Booting Priority The Boot menu in System Setup enables you to select the booting device and to set booting options. Boot Device Priority field enables: You to select the order in which the computer attempts to boot from different devices. The field has four (4) options: CD-ROM Drive, Removable Devices, Hard Drive and MBA UNDI (Bus2 Slot5). To change the booting device priority, choose the device positions by completing the following: 1. At startup, press to open System Setup. 2.
Configuring the Password Setting the Supervisor Password By configuring a supervisor password, you can restrict system access to authorized users only. To use a fingerprint in the fingerprint sensor installed model, refer to the supplied manual for the fingerprint sensor. 1. Select the Security menu in the System Setup. To enter System Setup, see “Starting System Setup” on page 61. 2. On the Set Supervisor Password item, press . 3.
Activating the Booting Password Before activating the booting password, the supervisor password must have been configured. Set the Password on boot option to [Enabled]. From now on, system booting will not proceed without the password. Activating the Hard Disk Drive Password Activating the hard disk drive password prevents the currently installed hard disk drive from being used in other systems. Before activating the hard disk drive password, the supervisor password must have been configured.
Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance. Your computer runs fastest with the power cord attached, when power management is disabled. In the next sections, basic and advanced methods of power management will be discussed.
3. Click the Power Schemes tab to display the basic power management options. Power Schemes Tab 4. Select the time that you wish each of the following actions to occur in Battery and AC power mode. • • • • Turn off monitor Turn off hard disks System standby System hibernates Turning off the monitor and HDDs will save a substantial battery power, therefore when in battery only mode select the shortest time practical.
If You Reinstall Windows: You should re-establish hibernate in power options by opening Power Options Properties window and click on the Hibernate tab then click “Enable Hibernation”. Hibernate Tab Frequent Interruptions: If you experience frequent interruptions, you might also consider putting your computer into automatic hibernation after a specified number of minutes using the power management options.
Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Control Panel > Performance and Maintenance. 2. Click icon to display the Power Options Properties window. 3. Click the Advanced tab to display the advanced power management options. Advanced Tab Power & Sleep Button Programming Windows 4.
Using the Hard Drive Your computer includes a removable IDE (integrated drive electronics) hard drive. The IDE hard drive can store the data and programs your computer uses. The drive plugs into a connector on the system board. The hard drive that comes with your computer has already been formatted. Do not format the hard drive. Doing so destroys all data contained on the drive.
Video Features and Configuration Resolution and Colour Depth The resolution of the LCD is the sharpness of the image it can display. Resolution is measured by the number of pixels (individual dots) displayed on the entire screen. In general, the more pixels the LCD can display, the better the image. The number of colours the LCD can display is measured by how many bits the LCD uses to represent each pixel: • 16-bit colour can support 64 K (65,536) colours. • 32-bit colour can support 16 M (16.
Configuring Display Features The following sections describe how to configure the display settings on your computer. Display Resolution Notes: When Windows XP is initially installed it will automatically adjust the resolution to maximum available. Changing Colour Depth and Resolution To change the colour depth and resolution of your LCD: 1. Click Start > Control Panel > Appearance and Themes. 2. Click icon. The Display Properties window appears. 3. Click the Settings tab. The Settings screen appears. 4.
SIC (Smart Inverter Control) Function SIC is a function that adjusts the LCD brightness automatically when the system is operating on battery power so that you can use the battery for a long time. SIC function is activated as a default. If you feel the screen is too dim, deactivate the SIC function following the procedures below. 1. Restart the system. 2. Press key to run System Setup. 3. Change the Smart Inverter Control item in Advanced menu to [Disabled]. 4.
Using External Display Devices Using external display devices such as a monitor, projector, TV, etc allows you to view screen images alternatively or simultaneously on each device. You can also split a screen into two display devices, or view different images on each display device. Using external display devices is especially useful when you are giving a presentation or watching a movie through your TV.
Using nView to View Extended Screen You can expand the screen into two display devices and work conveniently in a wide workspace. 1. Connect the external display device (e.g. a monitor or a projector) to the corresponding port of the system. To connect a TV, connect the TV to the TV output port of the system. 2. Click Start > Control Panel > Appearance and Themes > Display. 3. On the [Display Properties] window, click Settings tab > Advanced > nView tab. Select the desired item, and click Apply.
Using Dual View to View Extended Screen You can expand the screen into two display devices and work conveniently in separate workspaces. In Dual View mode, you can select the screen resolution and color quality for each display device, as if there were two separate graphics cards. 1. Connect the external display device (e.g. a monitor or a projector) to the corresponding port of the system. To connect a TV, connect the TV to the TV output port of the system. 2.
4. Click OK. The primary display device(the LCD) is indicated as '1', and the secondary display device is indicated as '2'. Now you can use each of the two display devices as independent display devices. 1 : Primary 2 : Secondary When using Dual View, it is recommended that LCD is kept as '1', the primary display device.
Using Options You can select these options at purchase: • Wireless communication module (802.11b, bluetooth) • Fingerprinter recognition system / scroll wheel • Memory stick slot You can purchse these options separately: • Extra battery pack (3 cell/6 cell) • Battery charger • Ear set The options that are available may change periodically. Contact your reseller for updated information on current and new options.
Memory Modules You can increase system memory by installing optional memory modules. To avoid possible system problems, use only approved memory modules in your computer. Please consult the appropriate sections of this manual, Samsung Technical Support, or the support Web site (www.samsungpc.com) for additional information. Before You Install Memory To prevent personal injury and damage to the equipment, follow the precautions listed here before installing a memory module.
Installing a Memory Module Handle a memory module carefully. Hold them only by the edges. To install a memory module: 1. Turn the computer over so that the bottom faces up. 2. Using a screwdriver, remove the screw that holds the memory-module compartment door in place. 3 Screw 3. Grasp the edge of the door and pull the door off the chassis. Memory Module Precautions: When removing the module, pull on the plastic portion of the connector slots tabs only.
5. Align the connector on the memory module with the connector of the slot. 6. Push the memory module into the slot at a slight angle (~30o) until the connectors are fully engaged. 6 7 7. Push down on the edge of the memory module until the module snaps into place. 8. Align the memory module compartment door with the compartment and push the door down until it snaps into place. 9. Reinstall the screw you removed in step 2.
Troubleshooting Complete the following in the order presented until your system is functioning properly. If all of the steps below fail then contact your local reseller for assistance. Questions and Answers Please see “Questions and Answers” on page 83 for assistance in correcting any computer operational problems. Check the Connections Verify all of the power and peripheral cables are securely plugged into their sockets and that your system and power supply is on.
Questions and Answers This section provides information on possible problems, solutions and other references for system use. Windows Related Q1 The system does not shutdown properly. A When the system does not shutdown normally, press and hold the Power button until the system manually shuts off. If the Power-Saving Mode is configured into the Power button, press and hold for more than 4 seconds to shut the system off.
Q3 In DOS mode or with a screen resolution lower than 1024x768 pixels, pressing the Fn+F2 key does not display the icon clearly. A The screen image is extended across the LCD size when the screen resolution setting is lower than 1024x768 pixels. If the icon appears unclear, it is because the video chip does not support this function, but it does not affect the system performance.
Q8 When I connect a projector, and change the setting to display screen image on both the LCD and the projector by pressing + keys, screen is not displayed properly. A Press + keys once again. Modem Related Q1 I cannot hear the modem sound. A1 Check that the telephone line is properly connected to the modem. A2 Check that the modem driver is installed properly. 1. Click Start > Control Panel > Performance and Maintenance > System. 2.
Q2 I cannot make a call using an extension line. A In general, the dial tone of a PBX or a digital phone switching system is not a continuous one, unlike that of trunk line. Therefore, the modem may not make a call because the modem mistakes the dial tone from a PBX or a digital phone switching system as a busy tone. In this case, complete the following procedures. - Using an AT command As an initialization command, use the command, ATX3. Otherwise, enter the ATX3 command manually before making a call.
Q4 How do I receive a fax while the system is in power saving mode (Rest mode) (For Windows XP and 2000)? A To receive a fax when the system is in power saving mode, and the operating system is Windows XP or 2000, configure the system as follows: 1. The automatic fax reception function of the fax program needs to be activated. (For more information, refer to the corresponding fax program manual.) 2. Click Start > Control Panel > Network and Internet Connections. 3.
A4 To connect to an access point using network authentication (Shared key): - In Windows XP, select Network Authentication (Shared mode) in the Wireless Network Properties window. - If you use the wireless LAN program (PROSet) in Windows 2000, make sure that the network authentication mode is configure to Shared in security settings. For more information on the network authentication configuration procedures, ask your access point administrator.
A2 Check that the AP is operating properly. Turn the AP off, and turn it on after a short wait. A3 Check that the network key (encryption key) configuration for the AP is correct. A4 Check if the wireless LAN/Bluetooth button on the upper part of the keyboard is switched off. If the wireless button is switched off, press the button to switch the wireless function on. If you are using Windows 2000, check if switch radio is set to "On" on the General tab of PROSet program.
Q7 When connecting to a computer-to-computer (Ad Hoc) network, I cannot connect to another computer connected to the same computer-to-computer network. A1 Make sure that the security settings and network name of the computer-tocomputer (Ad Hoc) network is correct. A2 Check the TCP/IP properties of the computers to be connected through the computer-to-computer (Ad Hoc) network. All of those computers should be configured so that their IP addresses are within the same subnet range.
Q2 I launched a game right after installing it, and the game is not executed. A This problem may occur when the game is not compatible with Windows XP. Launch the game again, and it will be executed properly. Q3 The screen is displayed in reduced size when playing a game. A This problem may occur when the Screen Expansion option in system setup is set to Disabled by default. To fit the screen on the LCD size, change the setting as follows: 1. Push the power button to start the system. 2.
(It may happen while running Harry Porter and the Chamber of Secrets, Warcraft 3, Unreal Tournament 2003, Starcraft, Quake 3, Soldier of Fortune 2, Heroes of Might or Magic 4.) Q7 Running speed of a game is too slow or fast. A Change the setting of Power Schemes to 'Always On'. (Click Start > Control Panel > Performance and Maintenance > Power Options > Power Schemes tab, then configure the Power schemes field to 'Always On'.
Reinstalling Software If you have reinstalled the Windows operating system, or the system and program do not operate properly, you can re-install the driver and program using the system software CD. The drivers and programs included in the system software CD are listed in the D:\ReadMe.htm file. (Provided that the name of CD-ROM drive is "D".) Running the system software CD Insert the system software CD into the CD-ROM drive. The initial screen appears automatically.
Installing programs 1. In the initial screen, click Install programs. 2. Click Standard installation in the program installation screen (standard installation is recommended). • Standard installation: Installs and recovers programs to the state of shipment. • User installation: You can select the program installation location, and other options for the program installation.
Reinstalling Windows XP If the Windows XP does not operate properly due to an error in the system, or if you have replaced the hard disk drive, you can reinstall Windows XP using the system recovery CD. With the system recovery CD, you can reinstall Windows XP only. To return the system to the state of shipment, reinstall the device drivers and programs with the system software CD after reinstalling Windows XP with the system recovery CD.
3. The description for the standard installation appears. Click Yes. The installation starts, and the system will be restarted after a while. 4. After the system has restarted, the message ’Press any key to boot from CD’ appears. Do not press any key at this time. After a while the partition configuration screen appears. To not change the partition, press . What is partition configuration? Partition configuration is a function that devides the hard disk drive into one or several partitions.
If You Cannot Run Windows If you cannot run Windows, you have to boot the system with the system recovery CD, and reinstall Windows. If you boot the system from the system recovery CD, you can install Windows only with the user installation option. You cannot install with the standard installation option. 1. Insert the system recovery CD into the CD-ROM drive and start the computer. 2. If the following message appears on the screen, press any key from the keyboard. Press any key to boot from CD.....
Specifications The following is the basic hardware specification for the purchased product. Variations may exist depending on the model type. Item Specification CPU Intel Banias 1.3~1.7GHz Cache memory 1MB Main memory 128/256/512/1024 MB DDR SDRAM, 2 DDR socket Main Chipset Odem/ICH4M Remarks Maximum 2GB Hard disk drive (HDD) 2.5’’, UltraDMA 100, S.M.A.R.T 9.
Wireless LAN Specification Item Physical Specifications Detailed Specifications Dimensions (Width X Height) 59.75 X 44.45 mm operation temperature and humidity Same as system operation Temperature: 0°C ~ 70°C Humidity: less than 85% Power Specification Network Specifications Power Saving Mode 135 mW Receiving Mode 1.0 W Transmission Mode 1.6 W Power 3.3V Compatibility IEEE802.11b standard (DSSS) Mini-PCI Rev.1.
Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country. In France however, use only 4 channels (channel 10, 11, 12, 13) when using wireless networks. • Standard: IEEE 802.
Abbreviations A . . . . . . . . . Amperes AC . . . . . . . . Alternating current ACPI . . . . . . Advanced Configuration and Power management Interface APM . . . . . . Advanced Power Management ATA. . . . . . . AT attachment (refers to the hard-drive interface in an ATcompatible computer) ATAPI. . . . . AT attachment packet interface BBS . . . . . . . Bulletin board system BIOS . . . . . . Basic input/output system C . . . . . . . . . Centigrade CD . . . . . . . . Compact disc CD-ROM . .
ISA . . . . . . . Industry Standard Architecture KB . . . . . . . . Kilobytes kg . . . . . . . . . Kilograms LAN. . . . . . . Local-area network lb.. . . . . . . . . Pounds LBA . . . . . . . Logical block addressing LCD. . . . . . . Liquid-crystal display m . . . . . . . . . Meters mA . . . . . . . . Milliampere mAhr . . . . . . Milliampere hour MB. . . . . . . . Megabyte mm . . . . . . . millimeter MPEG . . . . . Motion Picture Experts Group MPU . . . . . . Microprocessor unit ms . . . . . . . .
Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts). The 32-bit cards can transmit more data at a time than the 16-bit cards, thus increasing their speed. CMOS memory CMOS (complementary metal oxide semiconductor) memory is powered by the CMOS battery.
Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer. Because hard drives in notebook computers are smaller than those in desktop computers, their maximum storage capacity may be less than that of desktop hard drives.
PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed. Pixel A pixel is an individual dot in a graphic displayed on your computer. The pixels are so close together that they look as though they are connected.
Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer. TFT (thin film transistor) LCD A TFT LCD uses a separate transistor circuit to control each pixel. This technology provides the best resolution for an LCD screen. A TFT LCD is also sometimes called an active matrix LCD.