Gas Range Installation manual NX58M6650W*/NX58M6630S* NX5000M_NX58M6650WS_AA_DG68-00992A-01_EN+MES+CFR.
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. • DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. • WHAT TO DO IF YOU SMELL GAS: -- DO NOT try to light any appliance. -- DO NOT touch any electrical switch. -- DO NOT use any phone in your building. -- Immediately call your gas supplier from a neighbor’s phone.
Contents Before you begin 3 Important safety information 4 Gas range components Overview Gas range specifications Installation requirements Location requirements Gas requirements Special gas requirements (gas models sold in massachusetts) Electrical requirements Tools and materials What’s in the box Installation instructions Installing your gas range Adjusting the oven burner air adjustment shutters ABOUT THIS MANUAL READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.
Important safety information READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE • Important safety information • All electrical and gas equipment with moving parts can be dangerous. Please read the important safety instructions for this appliance in this manual. The instructions must be followed to minimize the risk of injury, death, or property damage. Save this manual. Please Do Not Discard.
• • • • • • • • • Fire safety WARNING To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. • • • • • • • Do not store, place, or use flammable or combustible materials such as paper, plastic, pot holders, linens, curtains, gasoline or other flammable vapors or liquids near the range. Do not wear loose fitting or hanging garments while using the range. To avoid grease buildup, regularly clean the vents.
Important safety information Gas safety Electrical and grounding safety WARNING WARNING Important safety information To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. • • • • If you smell gas: • • • Close the valve and do not use the range. Do not light a match, candle, or cigarette. Do not turn on any gas or electric appliances.
Installation safety • WARNING • • • • • • • • Have your range installed and properly grounded by a qualified installer, in accordance with the installation instructions. Any adjustment and service should be performed only by qualified gas range installers or service technicians. Do not attempt to service, modify, or replace your range or any part of your range unless it is specifically recommended in this manual. All other service should be referred to a qualified technician.
Important safety information Location safety Cooktop safety WARNING WARNING Important safety information To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. • • To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. This range is for indoor, household use only. Do not install the range in areas exposed to the weather and/or water.
• • • • • • Oven safety WARNING To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. • • • • • • • • • • • • • Important safety information • Make sure cookware handles are turned to the side or rear of the cooktop, but not over other surface burners. Stand away from the range while frying. Always heat frying oils slowly, and watch as they heat. If you are frying foods at high heat, carefully watch during the cooking process.
Important safety information Warming drawer safety (NX58M6650W* ONLY) Self-cleaning oven safety WARNING Important safety information To reduce the risk of fire, electric shock, personal injuries, and/or death, observe the following precautions. • The warming drawer is designed to keep hot foods at serving temperature. Always start with hot food. Cold or room temperature food cannot be heated, warmed, or cooked in the warming drawer. Bacteria will grow very rapidly in food that is between 40 and 140 °F.
Gas range components Overview 07 01 10 1/2 in (266.4 mm) 04 11 03 08 46 11/16 in (1185.4 mm) 02 Gas range components 09 36 3/16 in (919.0 mm) 10 05 04 Oven vent 05 Removable oven door 06 Warming¹ / Storage² drawer 07 Oven lights 08 Convection fan/ Convection heater 09 Oven rack system 10 Bake oven burner 11 Broil oven burner 29 15/16 in (761 mm) 9 /1 Do 6 in or (12 fu 07 lly .7 op mm en ) 03 Surface burners 47 02 Surface burner knobs (5 pcs) 28 01 Display 1 /4 W in ( ith 71 ha 7.
Gas range components BTU Ratings (NX58M6630S*) 01 02 03 04 05 01 02 03 04 05 Gas range components Cooktop Burner Placement (NX58M6630S* only) Cooktop Burners (under grates) Burner Locations and Output Ratings (NX58M6630S* only) BTU Ratings (NX58M6650W*) Left-Front: 16,000 BTU Left-Rear: 9,500 BTU Center: 10,000 BTU Right-Rear: 5,000 BTU Right-Front: 18,000 BTU 01 02 03 04 05 01 02 03 04 Left-Front: 15,000 BTU Left-Rear: 9,500 BTU Center: 10,000 BTU Right-Rear: 5,000 BTU Right-Front: 20,000 B
Gas range specifications MODEL NX58M6630S* MODEL NX58M6650W* DESCRIPTION Gas Free-Standing Range OVERALL DIMENSIONS 29 15/16 in (W) x 46 11/16 in (H) x 28 4/16 in (D) 761 mm (W) x 1185 mm (H) x 717.3 mm (D) Gas Free-Standing Range OVERALL DIMENSIONS 29 15/16 in (W) x 46 11/16 in (H) x 28 4/16 in (D) 761 mm (W) x 1185 mm (H) x 717.3 mm (D) ELECTRICAL Refer to the rating label. GAS, NG (NATURAL GAS) 5–13 in WC ELECTRICAL Refer to the rating label.
Installation requirements Location requirements Clearances and dimensions NOTE For OTR over Gas Stove, please follow local GAS CODE. BEFORE YOU BEGIN to install this appliance, refer to the following information, dimensions, and clearances. Do not locate the range where it may be subject to strong drafts. Provide adequate clearances between the range and adjacent combustible surfaces. These dimensions must be met for safe use of the range.
Minimum dimensions Recommended locations for gas piping and electrical outlets WARNING If overhead cabinets are provided, a range hood should also be provided that projects horizontally a minimum of 5 in (12.7 cm) beyond the front of the cabinets. This will dissipate any heat buildup in the overhead cabinets to prevent death, personal injury, and/or fire hazard. The ventilating hood must be constructed of sheet metal not less then 0.0122" thick.
Installation requirements Gas requirements Special gas requirements (gas models sold in massachusetts) Provide adequate gas supply COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS: Installation requirements This range is designed to operate at a pressure of 5 in (13 cm) of water column on natural gas or 10 in (25 cm) of water column on LP gas (propane or butane). Make sure you are supplying your range with the type of gas for which it is designed.
• • Wiring diagram is located on the back of the range. (Inside of the cover back wire) This range is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly polarized. • Gas models • • • • • • Ensure proper ground and firm connection before use. • • • • • CAUTION Failure to follow these instructions can result in death, fire, or electrical shock.
Tools and materials Usage situations where appliance power cord will be disconnected frequently What’s in the box Do not use an adapter plug in these situations because disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the adapter ground terminal.
Tools needed Parts needed Gas line shut-off valve 135-degree elbow (optional) Flexible metal Flare union adapter Flare union adapter appliance connector ¾ in or ½ in (NPT) x ½ in (NPT) x ½ in ½ in (ID) x 5 ft ½ in (ID) (ID) Lag bolt or ½-in (OD) sleeve anchor Phillips screwdriver Open-end or adjustable wrench Pipe wrench (2) Nut driver Pencil and ruler Level Pipe joint compound Utility knife Soapy water solution Tools and materials Flat-blade screwdriver English 19 NX5000M_NX58M6650WS_AA_D
Installation instructions Step 2. Connect the range to gas supply Installing your gas range IMPORTANT: Please read the following instructions, as well as the Important Safety Instructions section at the front of this manual, completely and carefully BEFORE installing and/or operating the gas range. Improper installation, adjustment, service, or maintenance can cause personal injury or property damage. NOTE To order parts or accessories, contact your local retailer or refer to the last page.
3. 4. 5. Install male 0.5-in (1.3-mm) flare union adapter to the 0.5-in (1.3-mm) NPT internal thread at the regulator inlet. Use a backup wrench on the regulator fitting to avoid damage. When installing the range from the front, remove the 90 ° elbow for easier installation. Install male 0.5-in (1.3-mm) or 0.75-in (1.9-mm) flare union adapter to the NPT internal thread of the manual shut-off valve, taking care to back up the shut-off valve to keep it from turning.
Installation instructions Step 3. Convert to LP gas (optional) NX58M6630S* All new gas ranges are shipped from the factory set up to use natural gas. Any Samsung gas range can be converted to use LP gas. Refer to page 52 in the User Manual to contact a qualified service technician. The conversion process should only be performed by a qualified LP gas installer. Conversion instructions and LP orifices will be supplied with the LP conversion kit.
Step 4. Install the anti-tip device Anti-Tip bracket WARNING To reduce the risk of tipping, the appliance must be secured by properly installing the anti-tip device packed with the appliance. • All ranges can tip, resulting in personal injury. • Tipping ranges can cause burns from spills, personal injury, and/or death. • To prevent accidental tipping, install and check the anti-tip bracket following the instructions and template supplied with the bracket.
Installation instructions Step 5. Plug in and place Step 6. Level the range 1. WARNING BEFORE OPERATING OR TESTING, follow the grounding requirements on pages 20 ~ 22 in this manual. Improper connection of the grounding plug can result in a risk of electric shock. • All gas ranges come with a power cord. The power cord is connected to the rear of the range. Please review "Electrical requirements" on pages 20 ~ 22. • All U.S.
Step 7. Assemble the surface burners 3. CAUTION Model NX58M6630S* Model NX58M6650W* Precise Simmer Burner (RR) Do not operate the surface burners without all burner parts in place. 1. Position surface burner heads on top of the surface burner manifolds as shown at right. The electrodes will fit into the slot in the bottom of the heads. Make sure the surface burner heads are flat and parallel with the cooktop. 2. Place the matching size caps on top of each surface burner head.
Installation instructions Step 8. Check the ignition of surface burners and oven burners To start the bake burners Check the operation of all cooktop and oven burners after the range has been installed and assembled, gas supply lines have been carefully checked for leaks, and electrical power cord has been plugged in. All surface and oven burners have electronic ignition. 02 01 03 04 To turn on a surface burner: 1. 2. 3.
Checking the flame quality: Step 9. Final installation checklist All combustion flames need to be visually checked to determine their flame quality. You have just completed installing your range. Make sure all controls are in the off position and the flow of ventilation air to the range is unobstructed. The following is a checklist to confirm your range is safely installed and ready for operation. 1. 1 2. 3. 2 3 Prevailing soft blue flames—Normal for natural gas operation.
Installation instructions Adjusting the oven burner air adjustment shutters Air adjustment shutter All oven burners have an air adjustment shutter. The purpose of the shutter is to regulate the flow of air to the flames. Properly adjusted flames should burn steadily with approximately 1-in of blue cone. The flames should never extend past the edge of the burner baffles. Even though these are preset at the factory, they should be checked and, if needed, adjusted periodically to ensure efficient operation.
Memo To adjust flame low setting Identify which burner is exhibiting too high or too low of simmer rate via manifold panel graphics. 1. Rotate a knob to "LO" position and remove the knob from the valve shaft while the flame is lit. 2. Carefully push the screw driver into the C chanel of the valve, until it hits the simmer set screw. Make sure the screwdriver flathead is seated into the set screw groove.
Scan the QR code* or visit www.samsung.com/spsn to view our helpful How-to Videos and Live Shows *R equires reader to be installed on your smartphone Please be advised that the Samsung warranty does NOT cover service calls to explain product operation, correct improper installation, or perform normal cleaning or maintenance. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT U.S.A Consumer Electronics 1-800-SAMSUNG (726-7864) www.samsung.com/us/support CANADA 1-800-SAMSUNG (726-7864) www.