Installation Guide 2020.04.14
Table Of Contents
- Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN
- Before you begin
- Important safety information
- Gas range components
- Installation requirements
- Installation instructions
- Installing your gas range
- Step 1. Unpack the range
- Step 2. Connect the range to gas supply
- Step 3. Convert to lp gas (optional)
- Step 4. Install the anti-tip device
- Step 5. Plug in and place
- Step 6. Level the range
- Step 7. Assemble the surface burners
- Step 8. Check the ignition of surface burners
- Step 9. Final installation checklist
- Adjusting the oven burner air adjustment shutters
- Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_MES
- Antes de comenzar
- Información importante de seguridad
- Componentes de la estufa a gas
- Requisitos de instalación
- Instrucciones de instalación
- Instalación de la estufa de gas
- Paso 1. Desembalaje de la estufa
- Paso 2. Conexión de la estufa al suministro de gas
- Paso 3. Conversión a gas LP (opcional)
- Paso 4. Instalación del dispositivo anti inclinación
- Paso 5. Enchufe y ubicación
- Paso 6. Nivelación de la estufa
- Paso 7. Montaje de los quemadores superiores
- Paso 8. Verificación del encendido de los quemadores superiores
- Paso 9. Lista de verificación final de la instalación
- Ajuste de los obturadores de ajuste del aire de los quemadores del horno
- Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_CFR
- Avant de commencer
- Informations importantes relatives à la sécurité
- Composants de la cuisinière à gaz
- Conditions d'installation
- Consignes d'installation
- Installation de votre cuisinière à gaz
- Étape 1 : déballage de la cuisinière
- Étape 2 : raccordement de la cuisinière à l'arrivée de gaz
- Étape 3 : conversion au GPL (facultatif)
- Étape 4 : installation du dispositif anti-basculement
- Étape 5 : branchement et mise en place
- Étape 6 : mise à niveau de la cuisinière
- Étape 7 : montage des brûleurs de la surface de cuisson
- Étape 8 : vérification de l'allumage des brûleurs de surface
- Étape 9 : vérification finale de l'installation
- Réglage des volets d'air du brûleur du four
24 English
Installation instructions
Installation instructions
Step 9. Final installation checklist
You have just completed installing your range. Make sure all controls are in the off
position and the ow of ventilation air to the range is unobstructed. The following
is a checklist to conrm your range is safely installed and ready for operation.
Gas Range Plug
Locking screw
– Gas line has been properly connected to
the range. The gas has been turned on. All
connections have been checked for leaks.
– Range is plugged into the properly
grounded electrical receptacle.
– Approved anti-tip bracket is properly
installed and engaged with the range.
– Range is leveled and is rmly sitting on a
solid, level oor.
– Gas surface burners have been properly
assembled.
– All burners have been tested for proper
operation.
– FOR INSTALLER ONLY—Check and/or
adjust the broil and oven burner ames as
described on pages 22-23 in this manual.
Adjusting the oven burner air adjustment shutters
Air
adjustment
shutter
All oven burners have an air adjustment
shutter. The purpose of the shutter is to
regulate the ow of air to the ames.
Properly adjusted ames should burn
steadily with approximately 1-in of blue
cone. The ames should never extend
past the edge of the burner bafes. Even
though these are preset at the factory, they
should be checked and, if needed, adjusted
periodically to ensure efcient operation.
To check and adjust the oven burner air adjustment shutters:
1. Open the oven door.
2. Remove the oven racks.
3. Remove the oven oor.
4. Press the Bake pad, then the START/SET pad.
5. After the oven has lit, visually check the ames coming out of the upper and
lower burners. If adjustment is needed, carefully adjust the air adjustment
shutters.
Locking screw
The shutters are located at the base of the
burner manifolds near the back oven wall.
To adjust the shutter, loosen the locking
screw and rotate the shutter towards the
open or closed position as needed. If ames
are lifting off the burner ports, gradually
reduce the air shutter opening until the
ames are stabilized.
If ames are too yellow and/or too large,
gradually increase the air shutter opening
until the ames have approximately a 1-in
blue cone.
NOTE
If the range is set up for natural gas, the ames should burn with no yellow
tipping. If the range is set up for LP gas, small yellow tips at the end of the cones
are normal.
Locking screw
After the ames are adjusted properly, shut
off the oven, retighten the locking screws,
replace the oven bottom and racks, and
close the oven door.
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 24 2020-03-26 6:41:26