User Manual
Table Of Contents
- Important safety information
- Overview
- Before you start
- Cooktop
- Dual Door™
- Electric oven
- Maintenance
- Troubleshooting
- Warranty (U.S.A)
- Warranty (CANADA)
- Información importante de seguridad
- Descripción general
- Antes de comenzar
- Cubierta
- Dual Door™
- Horno eléctrico
- Modo simple
- Modo doble
- Modo de cocción
- Guías de ajuste de temperatura
- Uso de las parrillas del horno
- Uso de la parrilla deslizante
- Uso del divisor
- Guía de recetas
- Modo Freidora de aire
- Sonda de temperatura (solo modo simple)
- Opciones de cocción
- Funciones especiales
- Más funciones
- Ajuste del sistema
- Control inteligente
- Control por voz
- Mantenimiento
- Resolución de problemas
- Garantía limitada (Estados Unidos)
- Garantía (CANADÁ)
- Informations importantes relatives à la sécurité
- Présentation
- Avant de commencer
- Table de cuisson
- Dual Door™
- Four électrique
- Mode Unique
- Mode Double
- Mode de cuisson
- Guides de réglage de la température
- Utilisation des grilles du four
- Utilisation de la grille coulissante
- Utilisation de la plaque de séparation
- Guide des recettes
- Mode Friture par application d'air
- Sonde thermique (mode Unique seulement)
- Options de cuisson
- Fonctions spéciales
- Fonctions supplémentaires
- Réglage du système
- Commande intelligente
- Commande vocale
- Entretien
- Dépannage
- Garantie (États-Unis)
- Garantie (CANADA)
English 49
Maintenance
Brass burner head
NOTE
• The brass parts of your burner will change
color with use. However, this will not
affect performance and you can clean the
brass parts with a brass cleaner.
• After cleaning, conrm that the burner
port openings aren't plugged.
• Shake out any excess water and then let
burner heads and caps dry thoroughly.
Placing the center burner upside down
will allow the water to drain out more
easily.
• Do not wash any burner components in a
dish washer.
CAUTION
• The starter electrodes are not removable. Do not attempt to remove them by
force.
• To avoid chipping, do not bang grates and caps against each other or against
hard surfaces, such as cast iron cookware.
• The burner head can be blocked by food or dust. Clean the head if it appears
blocked. If you clean the head with water, assemble it only after it is completely
dry. If the head is wet, it might prevent the burners from igniting.
• To avoid falling down the grates, make sure to remove both sides grates rst.
• Do not attempt to remove center oval burner cap from the head.
Burner grates and components
Turn off all surface burners and make sure they have all cooled down.
1
3
2
LL CC RR
1. Remove the center burner grate(C)
following both sides grates.(L/R)
2. Remove the burner caps from the burner
heads.
3. Remove the burner heads from the
valve manifolds to reveal the starter
electrodes.
4. Clean all removable grates and burner
components in warm, soapy water. Do
not use steel-wool pads or abrasive
cleaners.
5. Rinse and dry grates and burner
components thoroughly.
8
6
7
6. Return the burner heads to their
positions on top of the manifold valves.
Make sure a starter electrode is inserted
through the hole in each burner head.
NOTE
See the next page for detailed burner
component re-assembly instructions.
7. Return the burner caps to their positions
on top of the burner heads. To ensure
proper and safe operation, make sure the
burner caps lie at on top of the burner
heads.
8. Reinstall the burner grates in their
respective positions.
9. Turn on each burner and check if it
operates properly. After verifying that a
burner operates normally, turn it off.